OMAP4430 supports UTMI and ULPI types of transceiver interface.
In UTMI mode: The PHY is embedded within OMAP4430. The transceiver functionality
is split between the twl6030 PMIC chip and OMAP4430. The VBUS, ID pin
sensing and OTG SRP generation part is integrated in TWL6030 and UTMI PHY
functionality is embedded within the OMAP4430.
There is no direct interactions between the MUSB controller and TWL6030
chip to communicate the session-valid, session-end and ID-GND events.
It has to be done through a software by setting/resetting bits in
one of the control module register of OMAP4430 which in turn toggles
the appropriate signals to MUSB controller.
musb driver is register for blocking notifications from the transceiver
driver to get the event notifications for connect/disconnect and ID-GND.
Based on these events call the transceiver init/shutdown function to
configure the transceiver to toggle the VBUS valid, session end and ID_GND
signals to musb and power on/off the internal PHY.
For ID_GND event notifications, toggle the ID_GND signal and then wait for
musb to be configured as "A" device, and then call the transceiver function
to set the VBUS.
In OTG mode and musb as a host, When the Micro A connector used, VBUS is turned on
and session bit set. When the device is connected, enumeration goes through.
When the device disconnected from the other end of the connector(ID is still grounded),
link will detect the disconnect and end the session. When the device is connected back,
there are no events generated in the TWL6030-usb, and link is already down.
So the device is not detected. Removed the session bit disable code which
will recognize the connect of the device.
Limitation: In OTG host mode, if device is connected during boot, it does not get
detected. If disconnect and connect it back or connect after boot only it works.
Fix for this, I will submit seperate patch later.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
instead of using musb_platform_suspend/resume,
we can use dev_pm_ops and let the platform_device
core handle when to call musb_core's suspend and
glue layer's suspend.
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb core doesn't need to know about platform
specific details. So start moving clock
handling to platform glue layer and make
musb core agnostic about that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
that structure currently only holds a device
pointer to our own platform_device and musb's
platform_device, but soon it will hold pointers
to our clock structures and glue-specific bits
and pieces.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
preparing to a big refactor on musb code. We need
to be able to compile in all glue layers (or at
least all ARM-based ones) together and have a
working binary.
While preparing for that, we move every glue
layer to export only one symbol, which is
a struct musb_platform_ops, and make all
other functions static.
Later patches will come to allow for compiling
all glue layers together and have a working
binary.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removed the board_data parameter being
passed to musb_platform_init function
as board_data can be extracted from
device structure which is already member
of musb structure.
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since commit 461972d8a4 (musb_core: don't call
musb_platform_exit() twice), unloading the driver module results in a WARNING
"kobject: '(null)' (c73de788): is not initialized, yet kobject_put() is being
called." (or even kernel oops) on e.g. DaVincis, though only in the OTG mode.
There exists dubious and unbalanced put_device() call in musb_free() which
takes place only in the OTG mode. As this commit caused musb_platform_exit()
to be called (and so unregister the NOP transceiver) before this put_device()
call, this function references already freed memory.
On the other hand, all the glue layers miss the otg_put_transceiver() call,
complementary to the otg_get_transceiver() call that they do. So, I think
the solution is to get rid of the strange put_device() call, and instead
call otg_put_transceiver() in the glue layers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This pin-muxing is best done in the board files. The driver should
not do this explicitly.
Also, this code causes a warning to be thrown when OMAP2430 and OMAP3/4
support are enabled in the same kernel.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need mach-types and hardware.h
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
get_cpu_rev() is unused in this driver. It is probably legacy
code. So remove it.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function is only called inside omap2430.c...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function does nothing...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Program the OTG_INTERFSEL register based on
transcevier type passed from board file.
Adapt signature of musb_platform_init() function
for davinci, blackfin and tusb6010.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate/unbalanced call to clk_put() from musb_platform_exit() --
clk_put() gets called from musb_core.c anyway...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
we have those addresses already ioremaped, so let's
use our __raw_readl/writel wrappers.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding support for MUSB register save and restore during system
suspend and resume.
Changes:
- Added musb_save/restore_context() functions
- Added platform specific musb_platform_save/restore_context()
to handle platform specific jobs.
- Maintaining BlackFin compatibility by adding read/write
functions for registers which are not available in BlackFin
Tested system suspend and resume on OMAP3EVM board.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
drivers/usb/musb/omap2430.c:314:16: warning: Using plain integer as NULL pointer
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Omap3 MUSB AUTOIDLE functionality configured through OTG_SYSCONFIG
register prevents the device from going into retention.
This is a workaround (by Richard Woodruff/TI), as his comment :
> A new MUSB bug which is a match to data below was identified very
> recently (on hardware and in simulation).
> This bug is in 3430 and not 3630.
> As a priority test (and as new default) you should have engineers
> disable autoidle for MUSB block.
> This is the workaround which will show up in next errata.
Signed-off-by: Niilo Minkkinen <ext-niilo.1.minkkinen@nokia.com>
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup of OTG timer handling:
* unify decls for OTG time constants, in the core header
* set up and use that timer in a more normal way
* move to the driver struct, so it's usable outside core
And tighten use and setup of T(a_wait_bcon) so that if it's used,
it's always valid. (If that timer expires, the A-device will
stop powering VBUS. For non-OTG systems, that will be a surprise.)
No behavioral changes, other than more consistency when applying
that core HNP timeout.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Let the otg_transceiver in MUSB be managed by an external driver;
don't assume it's integrated. OMAP3 chips need it to be external,
and there may be ways to interact with the transceiver which add
functionality to the system.
Platform init code is responsible for setting up the transeciver,
probably using the NOP transceiver for integrated transceivers.
External ones will use whatever the board init code provided,
such as twl4030 or something more hands-off.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This email address is going to expire soon and my contribution to musb
is next to zero so remove it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor locking fix for musb_hdrc on OMAP3 and OMAP2430:
don't read DEVCTL without holding the spinlock, since
an IRQ could come in and corrupt things.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix three omissions in the "mode" sysfs attribute support:
(a) inability to report errors;
(b) no DaVinci support ... just report an error;
(c) for omap2430, accepting unsupportable values
The 2430 stuff is still odd....
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
