This fixes a lost 'key' variable declaration that went missing in a
mismerge (commit b981d8b3f5)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some NICs (3c905B) can not generate PME in power state PCI_D0, while others
like 3c905C can. Call pci_enable_wake() with PCI_D3hot should give proper
WOL for 3c905B.
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Tested-by: Harry Coin <hcoin@n4comm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a debugfs interface to look at internal ring state.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change how PHY is managed on SysKonnect fibre based boards.
Poll for PHY coming up 1 per second, but use interrupt to detect loss.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rather than bring network down/up when changing MTU,
only need to impact receiver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes problems with transmit hangs on older fiber based SysKonnect boards.
Adjust ram buffer sizing calculation to make it correct on all boards
and make it like the code in sky2 driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
net: Fix new EMAC driver for NAPI changes
This fixes the new EMAC driver for the NAPI updates. The previous patch
by Roland Dreier (already applied) to do that doesn't actually work. This
applies on top of it makes it work on my test Ebony machine.
This patch depends on "net: Add __napi_sycnhronize() to sync with napi poll"
posted previously.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Two small fixes to IPoIB support for bonding:
1- copy header_ops from slave to bonding for IPoIB slaves
2- move release and destroy logic to UNREGISTER from GOING_DOWN
notifier to avoid double release
Set bonding to version 3.2.1.
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Apparently poking the link status registers when autonegotiation
is running on the PHY might botch the PHY link on 80003es2lan
devices. While this is a very rare condition we can completely
avoid it alltogether by just using the MAC link bits to provide
the proper information to ethtool.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The xl_laa array is just 6 bytes long, so we should substract
10 from the index, like is also done some lines above already.
Signed-Off-By: Marcus Meissner <meissner@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A copy of struct net_device_stats now lives in struct net_device,
making in-driver copies a waste of memory.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
main change:
* greatly improve per-NIC probe diagnostic output. Similar to other
net drivers, print out MAC address, PHY info, and various hardware and
software flags that may be relevant.
other changes:
* similar to other net drivers, only print the initial version message
when we have found at least one board.
* don't bother to print error message when pci_enable_device() fails,
it will do so for us.
* use dev_printk() rather than printk() in nv_probe(). This gives
use a standardized output similar to the rest of the kernel, and
eliminates the need to manually print out PCI bus id.
* use DRV_NAME constant where appropriate
* clean struct pci_driver indentation
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This duplicates the read cycle timer feature of raw1394 (added in Linux
2.6.21) in firewire-core's userspace ABI. The argument to the ioctl is
reordered though to ensure 32/64 bit compatibility.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Check NodeID.nodeNumber as per OHCI 1.1 clause 7.2.3.2. See also IEEE
1394a table 5B-1.
Also, demote the "node ID not valid" message from error to notification
as it is not an error condition.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
at_context_queue_packet() didn't clean up in an early exit path.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
It seems unlikely, but access to self_id_cpu[0] could at least in theory
be deferred until after the loop over self_id_cpu[1..n] or even after
the subsequent reg_read. Enforce the desired order by a read barrier.
Also prevent the reg_read from being reordered relative to the for loop.
This isn't necessary if the loop's conditional printk counts as an
implicit barrier, but better make it explicit.
(self_id_cpu[] is a coherent DMA buffer.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Firewire-sbp2 did very uncooperative things in the kernel's shared
workqueue: Sleeping until reception of management status from the
target for up to 2 seconds, and performing SCSI inquiry and all of the
setup of SCSI command set drivers via scsi_add_device. If there were
transient or permanent error conditions, this caused long blockage of
the kernel's events process, noticeable e.g. by blocked keyboard input.
We now allocate a workqueue process exclusive to fw-sbp2. As a side
effect, this also increases parallelism of fw-sbp2's login and reconnect
work versus fw-core's device discovery and device update work which is
performed in the shared workqueue.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
On rare occasions, the ability to set one of the workaround flags at
runtime may save the day.
People who experience I/O errors with firewire-sbp2 while the old sbp2
driver worked for them should try workarounds=1 and report to the devel
mailinglist whether that improves things. Firewire-sbp2 defaults to the
SCSI stack's maximum transfer size per command, while sbp2 limits them
to 128 kBytes. Flag 1 accomplishes just that.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
On IOMMU-less noncoherent architectures, orb->callback will memcpy the
whole SCSI command buffer for READ-like SCSI commands. It is therefore
friendlier to enable IRQs before the call, like before patch "Add
ref-counting for sbp2 orbs".
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>
Sparse warned about it although it was apparently harmless:
drivers/firewire/fw-cdev.c:624:23: warning: symbol 'interrupt' shadows an earlier one
include/asm/hw_irq.h:29:13: originally declared here
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
drivers/ieee1394/ieee1394_core.c: Define spinlock using
DEFINE_SPINLOCK instead of assignment to SPIN_LOCK_UNLOCKED
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
At least since nodemgr got rid of coarse global locking, accesses to
struct csr1212_keyval's reference counter should be atomic and coupled
with proper barriers. Also, calls to csr1212_keep_keyval(kv) should
occur before kv is being used.
(We probably should convert refcnt to struct kref, but how to keep
csr1212_destroy_keyval's implementation non-recursively then?)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
csr1212_keep_keyval(kv) in nodemgr_process_root_directory was
unbalanced if ne->vendor_name_kv already exists. This happens for
example if eth1394 or raw1394 modify the local config ROM and it is
parsed again.
As a bonus, the attempt to add the vendor_name_kv sysfs attribute
when it already exists is now fixed for good.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* Delete optional and empty i2c client_register and client_unregister
callbacks.
* Use the proper i2c adapter ID.
* Don't use a template to initialize the i2c_adapter structure, it's
inefficient.
* Update a misleading comment on why we use i2c_transfer rather than
higher level i2c functions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The nodemgr host thread can exit on its own even when kthread_should_stop
is not true, on receiving a signal (might never happen in practice, as
it ignores signals). But considering kthread_stop() must not be mixed with
kthreads that can exit on their own, I think changing the code like this
is clearer. This change means the thread can cut its sleep short when
receive a signal but looking at the code around, that sounds okay (and
again, it might never actually recieve a signal in practice).
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
sbp2_host_reset and sbp2_handle_status_write are not serialized against
sbp2_alloc_device and sbp2_remove_device.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This belongs to user-space (and only if really needed).
text data bss dec hex filename
6723 2000 28 8751 222f drivers/ide/pci/amd74xx.o.before
3833 2000 16 5849 16d9 drivers/ide/pci/amd74xx.o.after
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drive->dn is initialized by ide-probe.c::probe_hwif() so no need to do it
in ->init_hwif method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This belongs to user-space (and only if really needed).
text data bss dec hex filename
7129 404 8 7541 1d75 drivers/ide/pci/sis5513.o.before
3916 404 1 4321 10e1 drivers/ide/pci/sis5513.o.after
Additionaly to being bloat the code contained two bugs:
- wrong cable bit was checked (0x0001 instead of 0x8000) on ATA_133 chipsets
- incorrect UDMA cycle time was reported on ATA_100a/ATA_133 chipsets
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ATAPI devices with broken DMA support should be handled by DMA blacklist
and for debugging purposes we have new shiny "hdx=nodma" kernel paremeter.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add "hdx=nodma" option allowing user to disallow DMA for a given device.
* Obsolete "ide=nodma" option.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt34x.c: disable DMA masks for HPT345
(hwif->autodma is zero so DMA won't be enabled anyway).
* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
(hwif->autodma is zero so DMA won't be enabled anyway).
* Check noautodma global variable instead of drive->autodma in ide_tune_dma().
This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.
* Remove hwif->autodma (it was not checked by IDE core code anyway) and
drive->autodma (was set by all host drivers - except HPT345/TRM290 special
cases - unless "ide=nodma" was used).
While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
(this setting was always later over-ridden by host drivers anyway)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It has been obsoleted since 1 Nov 2004, is valid only when used together with
"ide=nodma" kernel parameter (which makes no sense) and only for aec62xx,
cmd64x, cs5220, generic, hpt366, sl82c105, tc86c001 and triflex host drivers.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This code doesn't use pci_assign_resource() and ide_get_or_set_dma_base() uses
pci_resource_start() to get DMA base address so it has no chance of working.
Moreover this belongs to PCI quirks (in case somebody would like to fix it).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Clear prefetch and postwrite for ATAPI devices instead of depending on BIOS.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't force PIO4 when programming UDMA mode (suggested by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
noautodma can now be unexported.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide-pmac allows separate PIO and DMA timings, and ide-pmac always sets
->autotune this change shouldn't have any other effect than bringing ide-pmac
driver in-line with other host drivers wrt ->ide_dma_check implementation.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide-cris allows separate PIO and DMA timings, and ide-cris always sets
->autotune this change shouldn't have any other effect than bringing ide-cris
driver in-line with other host drivers wrt ->ide_dma_check implementation.
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since sl82c105 re-programs DMA/PIO timings for DMA enable/disable, and sets
->autotune this change shouldn't have any other effect than bringing sl82c105
driver in-line with other host drivers wrt ->ide_dma_check implementation.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add PIO autotune fallback to ->ide_dma_check.
Since cs5530/sc1200 allow separate PIO and DMA timings, and cs5530/sc1200
always set ->autotune this change shouldn't have any other effect than
bringing these drivers in-line with other host drivers wrt ->ide_dma_check
implementations.
* Fix ->ide_dma_check to return "-1" if DMA cannot be set.
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove ide_use_fast_pio() and just re-tune PIO unconditionally if DMA tuning
has failed in ->ide_dma_check. All host drivers using ide_use_fast_pio() set
drive->autotune so PIO is always tuned anyway and in some cases we _really_
need to re-tune PIO because PIO and DMA timings are shared.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Several host drivers used to reset drive->init_speed in their ->ide_dma_check
implementations which resulted in incorrect init speed being reported to the
user, fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove needless setting of drive->using_dma from auide_dma_check().
* Split off auide_mdma_filter() from auide_dma_check().
* Use ide_tune_dma() in auide_dma_check(), this fixes following issues:
- device's DMA capability bit not being checked
- device not being checked against generic DMA blacklist
- transfer mode not being set on device/host
* Add PIO autotune fallback to auide_dma_check().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix handling of unsupported/invalid modes in atiixp_set_dma_mode().
* ATI controllers allow separate PIO and DMA timings so remove programming
of PIO modes from atiixp_set_dma_mode(). Also remove no longer needed
atiixp_dma_2_pio() helper.
* SWDMA timings are not programmed by atiixp_set_dma_mode() and if SWDMA
mode is chosen atiixp_dma_host_on() erroneously enables UDMA, just disable
support for SWDMA modes for now.
* Enable support for MWDMA0 mode.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Always set ->autotune in init_hwif_sis5513(), this means practically
no change in behavior since PIO was always tuned in ->ide_dma_check
and >autotune was always set for ->dma_base == 0 case.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add sis_ata133_get_base() helper function for obtaining the address of
the drive control registers on chipset_family == ATA_133 chipsets.
* Add three helper functions for programming PIO/MWDMA timings:
- sis_ata16_program_timings() (for ATA_16/33/66/100a chipset families)
- sis_ata100_program_timings() (for ATA_100/133a chipset families)
- sis_ata133_program_timings() (for ATA_133 chipset family)
MWDMA timings are taken from datasheets and they match ATA spec.
* Add generic helper function sis_program_timings() and use it in
->set_pio_mode and ->set_dma_mode methods (previously the driver
depended on BIOS to program the correct MWDMA timings).
* Remove redundant !chipset_family check from init_hwif_sis5513()
(init_chipset_sis5513() guarantees that we will never get here if
chipset_family cannot be determined).
* SWDMA seems to be unsupported by SiS chipsets (no info about SWDMA in
datasheets and for SWDMA0 mode timing requirements are impossible to
fulfill) so remove ->swdma_mask from init_hwif_sis5513() and handling
of SWDMA modes from sis_set_dma_mode().
* Enable DMA support for chipset_family == ATA_16.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch adds id strings for Corsair 1GB (identified as Hyperstone Model1)
inside legacy/ide-cs.c.
It also includes some minor whitespace cleanups.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The patch described by the following excerpt from ChangeLog-2.6.22 makes
it impossible to use UDMA on a Tyan S2707 motherboard (SvrWks CSB5):
commit 2d5eaa6dd7
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Thu May 10 00:01:08 2007 +0200
ide: rework the code for selecting the best DMA transfer mode (v3)
...
This one-line patch against 2.6.23 fixes the problem.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently, the set_lazy_mode pv_op is overloaded with 5 functions:
1. enter lazy cpu mode
2. leave lazy cpu mode
3. enter lazy mmu mode
4. leave lazy mmu mode
5. flush pending batched operations
This complicates each paravirt backend, since it needs to deal with
all the possible state transitions, handling flushing, etc. In
particular, flushing is quite distinct from the other 4 functions, and
seems to just cause complication.
This patch removes the set_lazy_mode operation, and adds "enter" and
"leave" lazy mode operations on mmu_ops and cpu_ops. All the logic
associated with enter and leaving lazy states is now in common code
(basically BUG_ONs to make sure that no mode is current when entering
a lazy mode, and make sure that the mode is current when leaving).
Also, flush is handled in a common way, by simply leaving and
re-entering the lazy mode.
The result is that the Xen, lguest and VMI lazy mode implementations
are much simpler.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Zach Amsden <zach@vmware.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Anthony Liguory <aliguori@us.ibm.com>
Cc: "Glauber de Oliveira Costa" <glommer@gmail.com>
Cc: Jun Nakajima <jun.nakajima@intel.com>
This patch refactors the paravirt_ops structure into groups of
functionally related ops:
pv_info - random info, rather than function entrypoints
pv_init_ops - functions used at boot time (some for module_init too)
pv_misc_ops - lazy mode, which didn't fit well anywhere else
pv_time_ops - time-related functions
pv_cpu_ops - various privileged instruction ops
pv_irq_ops - operations for managing interrupt state
pv_apic_ops - APIC operations
pv_mmu_ops - operations for managing pagetables
There are several motivations for this:
1. Some of these ops will be general to all x86, and some will be
i386/x86-64 specific. This makes it easier to share common stuff
while allowing separate implementations where needed.
2. At the moment we must export all of paravirt_ops, but modules only
need selected parts of it. This allows us to export on a case by case
basis (and also choose which export license we want to apply).
3. Functional groupings make things a bit more readable.
Struct paravirt_ops is now only used as a template to generate
patch-site identifiers, and to extract function pointers for inserting
into jmp/calls when patching. It is only instantiated when needed.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Zach Amsden <zach@vmware.com>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Anthony Liguory <aliguori@us.ibm.com>
Cc: "Glauber de Oliveira Costa" <glommer@gmail.com>
Cc: Jun Nakajima <jun.nakajima@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: introduce ccflags-y, asflags-y and ldflags-y
kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP
kbuild: enable use of AFLAGS and CFLAGS on commandline
kbuild: enable 'make AFLAGS=...' to add additional options to AS
kbuild: fix AFLAGS use in h8300 and m68knommu
kbuild: check for wrong use of CFLAGS
kbuild: enable 'make CFLAGS=...' to add additional options to CC
kbuild: fix up CFLAGS usage
kbuild: make modpost detect unterminated device id lists
kbuild: call export_report from the Makefile
kbuild: move Kai Germaschewski to CREDITS
kconfig/menuconfig: distinguish between selected-by-another options and comments
kconfig: tristate choices with mixed tristate and boolean values
include/linux/Kbuild: remove duplicate entries
kbuild: kill backward compatibility checks
kbuild: kill EXTRA_ARFLAGS
kbuild: fix documentation in makefiles.txt
kbuild: call make once for all targets when O=.. is used
kbuild: pass -g to assembler under CONFIG_DEBUG_INFO
kbuild: update _shipped files for kconfig syntax cleanup
...
Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (264 commits)
[ALSA] version 1.0.15
[ALSA] Fix thinko in cs4231 mce down check
[ALSA] sun-cs4231: improved waiting after MCE down
[ALSA] sun-cs4231: use cs4231-regs.h
[ALSA] This simplifies and fixes waiting loops of the mce_down()
[ALSA] This patch adds support for a wavetable chip on
[ALSA] This patch removes open_mutex from the ad1848-lib as
[ALSA] fix bootup crash in snd_gus_interrupt()
[ALSA] hda-codec - Fix SKU ID function for realtek codecs
[ALSA] Support ASUS P701 eeepc [0x1043 0x82a1] support
[ALSA] hda-codec - Add array terminator for dmic in STAC codec
[ALSA] hdsp - Fix zero division
[ALSA] usb-audio - Fix double comment
[ALSA] hda-codec - Fix STAC922x volume knob control
[ALSA] Changed Jaroslav Kysela's e-mail from perex@suse.cz to perex@perex.cz
[ALSA] hda-codec - Fix for Fujitsu Lifebook C1410
[ALSA] mpu-401: remove MPU401_INFO_UART_ONLY flag
[ALSA] mpu-401: do not require an ACK byte for the ENTER_UART command
[ALSA] via82xx - Add DXS quirk for Shuttle AK31v2
[ALSA] hda-codec - Fix input_mux numbers for vaio stac92xx
...
- Previese patch to NCR5380 broke scsi_mac because
AUTOSENSE was defined after the inclusion of
NCR5380.h. Fix it
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a test in tgafb_mono_imageblit() for a colour image with a fall-back
to cfb_imageblit(). The test is not necessary as the only caller, which is
tgafb_imageblit(), checks it too and only invokes this function for monochrome
images. It looks like a left-over from before some changes to
tgafb_imageblit().
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Jay Estabrook <Jay.Estabrook@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pixel mask calculation in tgafb_mono_imageblit() uses a variable
left-shift on a 32-bit data type by up to 32. Shifting by the width of a data
type or more produces an unpredictable result according to the C standard.
Rather than widening the data type this fix makes sure the count is between 0
and 31. The reason is not to penalise 32-bit platforms with operation on a
"long long" type for a marginal case that is meant not to happen (blitting an
image of a zero width).
The reason it has escaped for so long is the Alpha, being purely 64-bit, :-)
does not mask the shift out to 32 bits. This is a valid implementation --
producing the correct result certainly falls within "unpredictable behaviour".
It does trigger on MIPS though and it is the recent merge of the TC support
which only enabled the driver for use on anything other than the Alpha. For
MIPS when the width is 32 the mask ends up being 0 rather than 0xffffffff as
it should be and the frame buffer is not updated.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Jay Estabrook <Jay.Estabrook@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported in Bugzilla Bug 9093, upon switching to X, a small rectangular
cursor can still be seen blinking in the upper left part of the screen. It is
fbcon's text cursor. This is caused by a strange ioctl(..., KDSETMODE,
KD_TEXT) call done by something in userspace, perhaps by X itself, while the
tty is still in graphics mode. And when the tty is in KD_TEXT mode, the
cursor timer is restarted.
Although this is a userspace problem, we can work around it by delaying the
restart of the cursor timer until an fbcon_switch() is called. In other
words, the cursor timer will not be restarted even if a KD_TEXT mode switch is
requested.
Regression potential: Present but low
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This correct case, when source and destination X coordinates difference is n
multiple of pixels in byte. This is probably rare case, but this case should
supported for completeness.
Reorganization of FB_READL and FB_WRITEL calls results in code size decrease
for normal build without swapping support and size with support enabled is
reasonable too.
[adaplas]
Add missing fb_rev_pixels_in_long() prototype.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds check if selected pixclock is valid (is in the PLL range).
Previously, if the pixclock could not be set, the new mode resolution was set
but pixclock was not set which led to incorrect timings sent to monitor.
[adaplas]
Fixed a few misplaced curly braces.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes mode selection matching algorithm. It allows to choose
mode with matching depth even when requested color lengths are greater than
color lengths of every mode with requested color depth.
It also fixes bug in s3fb - wrong error value returned when format is not
supported by chip.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Default to the 480p video mode on DVI-D and HDMI displays if `video=safe' is
passed on the kernel command line.
This is intended to be used by `kboot'-style boot loaders (i.e. first-stage
kernels) for the PS3, to provide a failsafe video mode.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the extern declaration for global_mode_option to <linux/fb.h> and rename
the variable to fb_mode_option.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Enhance horizontal panning on firmware 1.90 and up:
- On firmware 1.90 and up, L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT supports copying
rectangles from XDR to DDR memory with different source and destination
line lengths. Hence larger horizontal virtual resolutions can be supported
(up to 16368 pixels).
- As the actual frame buffer memory layout no longer matches the entries in
ps3fb_res[], create fake struct ps3fb_ioctl_res data for the
PS3FB_IOCTL_SCREENINFO ioctl, so user space applications that depend on it
keep on working.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Add virtual screen and panning support:
- The vertical virtual screen size is limited by the amount of memory
reserved for ps3fb,
- The horizontal virtual screen size is limited to the fullscreen width,
- Advertise that we support panning, so fbcon will use it if the virtual
screen is enabled.
Enabling a virtual screen (using `fbset -vyres nnn') can speed up text
console scrolling by a factor of 10-15, depending on the video mode.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't keep the borders for non-fullscreen modes in XDR memory:
- Extract ps3fb_sync_image()
- Work around the alignment restrictions of L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT
by using an offset with L1GPU_CONTEXT_ATTRIBUTE_DISPLAY_FLIP
- Only copy the visible part of the screen on every vblank
- Always put the real frame buffer at the start of video memory
- Clear fullscreen DDR memory on mode change
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Use fb_info.par properly:
o Move mode-specific fields into struct ps3fb_par
o Allocate struct ps3fb_par using framebuffer_alloc()
o Protect access to ps3fb_par in ps3fb_sync() using the console semaphore
(this semaphore is already held when ps3fb_set_par() is called)
o Avoid calling ps3av_set_video_mode() if the actual video mode hasn't
changed
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: In the case of non-fullscreen video modes, there was a partial overlap
of the GPU command buffer and the frame buffer. Fix and cleanup various issues
with overlap and alignment:
- Move the GPU command buffer from the beginning to the end of video memory
- Exclude the GPU command buffer from the actual frame buffer memory
- Align the start of the virtual frame buffer to PAGE_SIZE instead of to 64
KiB, and don't waste memory if it's already aligned (for fullscreen modes)
- Take into account the alignment when checking memory requirements and
maximum number of frames
- Make sure fb_fix_screeninfo.smem_start always points to the virtual frame
buffer start, so we don't have to compensate for that in ps3fb_mmap()
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make ps3fb_wait_for_vsync() and ps3fb_flip_ctl() static, as they're no
(longer) used outside ps3fb.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up includes
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not print warnings on invalid frame numbers, as this can be triggered from
user space.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i.MX frame-buffer read operation should be faster for all configurations
then drawing each individual character again in response to scroll events.
The nonstandard fields allows to configure frame-buffer special options flags
for different display configurations by board specific initialization code.
One of such specific options is reversed order of pixels in each individual
byte. i.MX frame-buffer seems to be designed for big-endian use first. The
byte order is correctly configured for little-endian ordering, but if 1, 2 or
4 bits per pixel are used, pixels ordering is incompatible to Linux generic
frame-buffer drawing functions.
The patch "Allow generic BitBLT functions to work with swapped pixel order in
bytes" introduces required functionality into FBDEV core. The pixels ordering
selection has to be enabled at compile time CONFIG_FB_CFB_REV_PIXELS_IN_BYTE
and for each display configuration which requires it by flag
FB_NONSTD_REV_PIX_IN_B in "nonstd" field of info structure.
This patch provides way for board specific code to select this option.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
don't distinguish between `boot' and `non-boot' autodetection now the
autodetection code has been improved
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
add a quirk database for broken monitors where the `best' advertised
video mode doesn't work
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
treat DVI-D monitors like HDMI monitors when autodetecting the best video mode
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It doesn't make much sense to use the PS3AV_CMD_VIDEO_VID_* values in the
autodetection code, just to convert them to PS3 video mode ids afterwards.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3av: eliminate PS3AV_DEBUG
- Move ps3av_cmd_av_monitor_info_dump from ps3av_cmd.c to ps3av.c, as
it's
used there only
- Integrate ps3av_cmd_av_hw_conf_dump() into its sole user
- Use pr_debug() for printing debug info
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move AGP and DRM menus into the video graphics support menu.
They use 'menuconfig' so that they can all be disabled with
one selection.
Make the console menu use 'menuconfig' so that it can all be
disabled with one selection.
Make the frame buffer menu use 'menuconfig' so that it can all be
disabled with one selection.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add logo.nologo kernel boot option to disable the logo in order to provide
more screen space for kernel messages; especially useful when debugging and
screen space is more critical.
newport_con driver changes are untested.
[akpm@linux-foundation.org: cleanups, coding-style fixes]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add error messages to the probe call.
[adaplas]
On failure, return actual error value instead of -ENXIO.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the i2c ports are to be reversed, I2C_CLASS_HWMON assignment must also be
reversed.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various console drivers are able to resize the screen via the con_resize()
hook. This hook is also visible in userspace via the TIOCWINSZ, VT_RESIZE and
VT_RESIZEX ioctl's. One particular utility, SVGATextMode, expects that
con_resize() of the VGA console will always return success even if the
resulting screen is not compatible with the hardware. However, this
particular behavior of the VGA console, as reported in Kernel Bugzilla Bug
7513, can cause undefined behavior if the user starts with a console size
larger than 80x25.
To work around this problem, add an extra parameter to con_resize(). This
parameter is ignored by drivers except for vgacon. If this parameter is
non-zero, then the resize request came from a VT_RESIZE or VT_RESIZEX ioctl
and vgacon will always return success. If this parameter is zero, vgacon will
return -EINVAL if the requested size is not compatible with the hardware. The
latter is the more correct behavior.
With this change, SVGATextMode should still work correctly while in-kernel and
stty resize calls can expect correct behavior from vgacon.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move video graphics driver configs to fix menus:
Fix FB_PMAGB_B to depend on FB so that the FB menus remain
listed in order and indented correctly.
Fix FB_IBM_GXT4500 to depend on FB so that the FB menus remain
listed in order and indented correctly.
The OMAP FB drivers still muck up the FB menu a bit, so I put
OMAP drivers at the end of the FB menu.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel FB: allow odd- and even-field-first in interlaced modes, and
proper sync to vertical retrace
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <sylvain.meyer@worldonline.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel FB: the chip adds two halflines automatically in interlaced mode,
force even line count for the right timings.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <sylvain.meyer@worldonline.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add error messages to the probe call.
While they may rarely trigger, they may be useful when something weird is
going on. Also this is good style.
[akpm@linux-foundation.org: remove unneeded initialisation]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make radeonfb work ith the 200m Xpress RC410. In my tests it was terribly
unstable and would freeze until I set a refresh rate in the kernel argument
to 75.
e.g video=radeonfb:1280x800@75
Now it is rock solid.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a missing FB dependency to FB_PMAGB_B.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes all errors pointed by the checkpatch.pl script.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces busy waiting with the cpu_relax() call. This makes
scrolling faster.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces busy waiting with the cpu_relax() call. This makes
scrolling faster.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces busy waiting with cpu_relax() call. This makes scrolling
faster.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Add a `mode' parameter to ps3fb_get_res_table(), as in some cases it
should check the full-screen flag of the _new_ video mode instead of the
current video mode.
This bug caused spurious mode change failures when switching between
fullscreen and non-fullscreen modes using fbset, while ps3-video-mode worked
fine.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the black and white stripes issue with WUXGA monitor via HDMI.
It seems that when we use a VESA resolution from boot up, the AV settings
driver could not be initialized correctly. In that case we need a dummy
packet before VESA setting.
[Geert] Refactored to reduce code duplication.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow generic frame-buffer code to correctly write texts and blit images for
1, 2 and 4 bit per pixel frame-buffer organizations when pixels in bytes are
organized to in opposite order than bytes in long type.
Overhead should be reasonable. If option is not selected, than compiler
should eliminate completely all overhead.
The feature is disabled at compile time if CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is
not set.
[adaplas]
Convert helper functions to macros if feature is not enabled.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a few nvidia hardware where the i2c port assignments are reversed,
i.e., the 1st i2c port is assigned to the secondary display and the 2nd i2c
port to the primary display. In most cases, if only 1 display is attached, or
if only 1 flatpanel and 1 analog display is attached, the port reversal is of
no consequence. However if 2 flatpanels are attached, it can cause display
problems.
There is no sane way of determining if the hardware reversed the i2c port
assignment, so the simplest fix is to add a boot/module option, "reverse_i2c
to explicitly reverse the i2c port.
This also restores i2c ordering back to the pre-2.6.22 state.
Signed-off-by: Antonino Daplas <adaplas@gail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, if the refresh rate is not specified, fb_find_mode() returns the
first known video mode with the requested resolution, which provides no
guarantees wrt the refresh rate. Change this so that the mode with the
highest refresh rate is returned when the driver provides a custom video mode
database and the monitor limits, and a mode with the safe 60 Hz refresh rate
otherwise.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel framebuffer now supports interlaced video modes.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changed things:
1. vmalloc()/vfree() replaced with rvmalloc()/rvfree() (taken from
drivers/media/video/se401.c)
2. mmap method implemented (mostly taken from drivers/media/video/se401.c)
3. smem_start and smem_len fields of struct fb_fix_screeninfo initialized.
(smem_start initialized with virtual address, don't know if it is really
bad...)
[adaplas: sparse warning fix]
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch:
- disallows setting of virtual height above 2048 as it does
not work for accelerated copyarea and imageblit
- fixes blinking of pm2v cursor by pushing cursor outside
the display (x=2047)
- fixes hardware cursor position on Permedia 2 chips with
panning enabled
- enables hardware cursor by default
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds hardware cursor support for the Permedia 2 chip.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes:
- redundant fields from the cirrusfb_regs structure
- one redundant header
- fixes two includes ("" to <>)
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch does some "short-range" code improvements like merging identical
switch clauses, replacing conditional branches with calculation of values,
merging only once-used functions into place they are called from.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes unused or redundant fields from cirrusfb_info structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces "typedef enum" with "enum type" constructs. Using the
typedef is error for the checkpatch.pl script.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes over 850 errors and warnings pointed out by the checkpatch.pl
script.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes mode selection to always prefer default mode if possible
and always honor type of display set by default mode settings.
This patch is required in case the same display modes were defined for
different panels (e.g. STN and TFT).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes lcdcon1 register field from the s3c2410fb_display as all
bits are calculated from other fields.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds pixelclock field to the s3c2410fb_display structure and make
use of it in the driver.
The Bast machine defined 9 modes but pixclock and margin values are defined
only for the 640x480 modes so I removed other modes.
This patch also fixes wrong display type constant for the SMDK2440 board.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch:
- moves more display mode preparations to s3c2410fb_check_var()
- reduces number of fields in s3c2410fb_info
- removes redundant values setting in s3c2410fb_probe()
- removes static mach_info pointer
- releases fb_info structure in s3c2410fb_remove()
- changes s3c2410fb_init to __init from __devinit
- fixes few typos in comments and removes unused includes
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces <asm/uaccess.h> with <linux/uaccess.h> after the
checkpatch.pl hint. The include of <asm/uaccess.h> is removed if the driver
does not use it.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
