In case the pxa3xx-u2d driver isn't used, probing of ohci-pxa27x will cause an
ugly kernel crash (NULL pointer dereference in pxa3xx_u2d_start_hc(), because
struct u2d is NULL and clk_enable() call will crash the kernel, trying to access
it).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
USB2.0 Device Controller (U2DC) which is found in Marvell PXA3xx.
U2DC supports both High and Full speed modes.
PXA320 and PXA300 U2DC supports only UTMI interface.
PXA310 U2DC supports only ULPI interface and has the OTG capability.
U2D Controller ULPI driver introduced in this patch supports only the
PXA310 USB Host via the ULPI.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (28 commits)
ARM: 6411/1: vexpress: set RAM latencies to 1 cycle for PL310 on ct-ca9x4 tile
ARM: 6409/1: davinci: map sram using MT_MEMORY_NONCACHED instead of MT_DEVICE
ARM: 6408/1: omap: Map only available sram memory
ARM: 6407/1: mmu: Setup MT_MEMORY and MT_MEMORY_NONCACHED L1 entries
ARM: pxa: remove pr_<level> uses of KERN_<level>
ARM: pxa168fb: clear enable bit when not active
ARM: pxa: fix cpu_is_pxa*() not expanding to zero when not configured
ARM: pxa168: fix corrected reset vector
ARM: pxa: Use PIO for PI2C communication on Palm27x
ARM: pxa: Fix Vpac270 gpio_power for MMC
ARM: 6401/1: plug a race in the alignment trap handler
ARM: 6406/1: at91sam9g45: fix i2c bus speed
leds: leds-ns2: fix locking
ARM: dove: fix __io() definition to use bus based offset
dmaengine: fix interrupt clearing for mv_xor
ARM: kirkwood: Unbreak PCIe I/O port
ARM: Fix build error when using KCONFIG_CONFIG
ARM: 6383/1: Implement phys_mem_access_prot() to avoid attributes aliasing
ARM: 6400/1: at91: fix arch_gettimeoffset fallout
ARM: 6398/1: add proc info for ARM11MPCore/Cortex-A9 from ARM
...
When CONFIG_PXA3xx is not selected, cpu_is_pxa3xx() doesn't expand to
zero, which in some places doesn't result in correct optimization.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Reported-and-tested-by: Marek Vasut <marek.vasut@gmail.com>
This fixes the regression caused by the commit 6fee48cd33
("dma-mapping: arm: use generic pci_set_dma_mask and
pci_set_consistent_dma_mask").
ARM needs to clip the dma coherent mask for dmabounce devices. This
restores the old trick.
Note that strictly speaking, the DMA API doesn't allow architectures to do
such but I'm not sure it's worth adding the new API to set the dma mask
that allows architectures to clip it.
Reported-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to PXA3xx Processor Family Developer Manuall Vol1. section
"Pin Descriptions and Control", PXA30x and PXA31x Processor Alternate
Function Table shows the Alt FN 0 for GPIO51 is CI_HSYNC and for GPIO52
is CI_VSYNC. This patch fixes the MFP defines and also corrects the
order of MFD defines.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is causing section mismatches when linking, as cpufreq_driver->init()
is not supposed to be in init section.
Reported-by: Tomáš 'Sleep_Walker' Čech <sleep_walker@suse.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
ffuart is available on cm-x300 only with pxa300.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: stable <stable@kernel.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Improve formating so checkpatch passes. Also, change some function and variable
names to make the naming consistent.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This huge patch mostly shuffles code. The spitz.c file contained terrible mess
and needed a cleanup, here it is:
1) Made every part modular, components are not built in if not selected.
2) Removed loads of preprocessor goo, mostly "#ifdef MACH_AKITA .... #endif" and
similar code. The kernel size will grow by a few kb now, but the file is much
more readable.
3) Reworked SD/CF power setting function and made it reentrant.
4) Add ISL6271A regulator support
5) Correctly register WM8750
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This contains common code for Palm LD, TX, T5, Z72, Treo680, Centro
This code also adds PMIC support for all the devices,
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
READ_GPIO_BIT() is no way generic by accessing GPIO registers directly,
replace it with gpio_get_value().
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
IDE_PXA_CF doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Juergen Schindele <schindele@nentec.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
XSCALE_CACHE_ERRATA doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
CORGI_SSP_DEPRECATED doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
ARCH_GUMSTIX_ORIG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
BACKLIGHT_CORGI was later renamed to BACKLIGHT_GENERIC and has not been
used since then. As it's now safe to completely transition to LCD_CORGI
driver, which incorprates both the LCD and backlight device.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch:
1) Simpifies the DRI recomputation routine by pulling out the common code
2) Fixes a bug in PXA27x DRI recomputation caused by incorrect parenthesis
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The latest PXA3xx DM has enabled 312MHz for the HSS bus,
which allows x24 multiplier.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
With kexec-based kernel boot loader on Zaurus, the machine ID is
actually correctly passed, and head-sharpsl.S is not necessary.
Introduce PXA_SHARPSL_DETECT_MACH_ID, and include head-sharpsl.S
only when that's explicitly enabled.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
1. TOSA related un-hidden options moved to right under MACH_TOSA
2. SHARPSL_PM related hidden options moved to the end of Kconfig
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Not tested and enabled on MMP at this moment, and since the IRQ
is different from mach-pxa, I'd prefer to move the PMU device
back into mach-pxa/. Will introduce the PMU device to MMP once
it's enabled and tested.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
pxa3xx cpu needs the irq type setup to be able to
wakeup from low power mode on IRQ_WAKEUPx events.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This file is scheduled for removal, therefore fix all devices that use this
file to use the suggested wm97xx.h and pass platform data properly.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Tomas Cech <sleep_walker@suse.cz>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
