This patch updates the version number to 3.92.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All variants of the 5714, 5715, and 5780 offer a feature called the
"Universal Management Port". This feature is implemented in firmware
and is largely transparent to the driver, except...
It turns out that the UMP firmware needs to know the current status
of the link. Because the firmware cannot touch the PHY registers while
the driver is in control of the device, it needs the driver to report
link status changes through an additional handshaking mechanism.
Without this handshake, it has been observed in the field that the UMP
firmware will not operate correctly.
This patch implements the new handshake with the UMP firmware. Since
the handshake uses the same mechanism ASF heartbeats use, code was
added to detect and wait for completion of a pending previous event.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A CPMU related loopback test bug existed for AX revisions of the 5761.
While that errata has been fixed, the CPMU still slows down the core
clock too far to run the loopback test successfully. This patch
disables the CPMU LINK_SPEED mode just like we do with the AX
revisions of the 5761 and all revisions of the 5784.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5761 NVRAM sizes assigned to the nvram_size member are half as big
as they should be. This patch corrects the NVRAM sizes and replaces
the hardcoded constants with preprocessor constants for readability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MI clock is not configured correctly on adapters with the CPMU
present. The tg3 driver has code which statically sets the MI clock to
be a fraction of the speed at which the core clock is running.
However, the CPMU can change the adapter's core clock frequency based
on operating conditions. Consequently, the MI will run slow when the
core's clock has been slowed down.
There is a new 500KHz constant frequency clock available on adapters
with a CPMU. This patch removes the static core clock scaling and
configures the MI clock to use this new 500KHz clock instead.
Running the MI clock at slower speeds will not directly result in data
corruption, but it does challenge the PHY read and write routine timeouts.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent proposed feature addition to the virtio block driver revealed
some flaws in the API: in particular, we assume that feature
negotiation is complete once a driver's probe function returns.
There is nothing in the API to require this, however, and even I
didn't notice when it was violated.
So instead, we require the driver to specify what features it supports
in a table, we can then move the feature negotiation into the virtio
core. The intersection of device and driver features are presented in
a new 'features' bitmap in the struct virtio_device.
Note that this highlights the difference between Linux unsigned-long
bitmaps where each unsigned long is in native endian, and a
straight-forward little-endian array of bytes.
Drivers can still remove feature bits in their probe routine if they
really have to.
API changes:
- dev->config->feature() no longer gets and acks a feature.
- drivers should advertise their features in the 'feature_table' field
- use virtio_has_feature() for extra sanity when checking feature bits
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
So, we previously had a 'VIRTIO_NET_F_GSO' bit which meant that 'the
host can handle csum offload, and any TSO (v4&v6 incl ECN) or UFO
packets you might want to send. I thought this was good enough for
Linux, but it actually isn't, since we don't do UFO in software.
So, add separate feature bits for what the host can handle. Add
equivalent ones for the guest to say what it can handle, because LRO
is coming too (thanks Herbert!).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Herbert tells me that returning NETDEV_TX_BUSY from hard_start_xmit is
seen as a poor thing to do; we should cache the packet and stop the queue.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu points out (within another patch) that my scatterlists are
too short: one entry for the gso header, one for the skb->data, and
MAX_SKB_FRAGS for all the fragments.
Fix both xmit and recv sides (recv currently unused, coming in later
patch).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
get_buf() gives the length written by the other side, which will be
zero. We want to add the skb length.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
There was an obvious typo in LED structure
initialization which caused the radio and quality/activity
leds to be incorrectly initialized which resulted in
the leds not being enabled.
Additionally add the rt2x00led_led_activity() handler
that will enable TX/RX activity leds when the radio
is being enabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The timing settings for 1MBs should exclude
the short preamble bit since that only applies
to 2MBs, 5.5MBs and 11MBs.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
direct_mask will be set when we are not associated and requesting a
direct scan. The second debug print will be confusing as priv->essid
is not set at that time and it will thus print "<hidden>" while it is
known to which AP a direct scan is requested - as previous debug message
also indicates.
Now make all debugging consistent.
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All channels should be scanned, including the current channel
when the client is associated.
Removed also unused flag to scan only active channels.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some TX/RX related locking issues.
With this patch applied, some of the PHY transmission errors are fixed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various improvements for configuring the MPC5200 MII link from the
device tree:
* Look for 'current-speed' property for fixed speed MII links
* Look for 'fsl,7-wire-mode' property for boards using the 7 wire mode
* move definition of private data structure out of the header file
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
It's easy: grab locks before talking to hardware and realease
them afterwards. The one big lock has been splitted into a hw_lock
and mii_lock.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
linux-2.6-mk68/drivers/net/fec.c: In function 'fec_enet_module_init':
linux-2.6-mk68/drivers/net/fec.c:2627: warning: unused variable 'j'
linux-2.6-mk68/drivers/net/fec.c: At top level:
linux-2.6-mk68/drivers/net/fec.c:2136: warning: 'mii_link_interrupt' defined but not used
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the acquisition of unused interrupt types. We don't need to
register all the TX and RX varients used on some ColdFire FEC hardware.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Renamed the 5272 hash_table registers to match the "grp" hash_table
registers of the other ColdFire parts. They are actually a group hash.
The makes for consistent setup across all ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to Coverity (kudo's to Adrian Bunk), we had one use-before-check
bug in libe libertas driver. This patch fixes this issue.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes operation of dual-PHY (A/B/G) devices.
Do not anounce the A-PHY to mac80211, as that's not supported, yet.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (53 commits)
tcp: Overflow bug in Vegas
[IPv4] UFO: prevent generation of chained skb destined to UFO device
iwlwifi: move the selects to the tristate drivers
ipv4: annotate a few functions __init in ipconfig.c
atm: ambassador: vcc_sf semaphore to mutex
MAINTAINERS: The socketcan-core list is subscribers-only.
netfilter: nf_conntrack: padding breaks conntrack hash on ARM
ipv4: Update MTU to all related cache entries in ip_rt_frag_needed()
sch_sfq: use del_timer_sync() in sfq_destroy()
net: Add compat support for getsockopt (MCAST_MSFILTER)
net: Several cleanups for the setsockopt compat support.
ipvs: fix oops in backup for fwmark conn templates
bridge: kernel panic when unloading bridge module
bridge: fix error handling in br_add_if()
netfilter: {nfnetlink,ip,ip6}_queue: fix skb_over_panic when enlarging packets
netfilter: x_tables: fix net namespace leak when reading /proc/net/xxx_tables_names
netfilter: xt_TCPOPTSTRIP: signed tcphoff for ipv6_skip_exthdr() retval
tcp: Limit cwnd growth when deferring for GSO
tcp: Allow send-limited cwnd to grow up to max_burst when gso disabled
[netdrvr] gianfar: Determine TBIPA value dynamically
...
Something Arjan suggested which allows us to clean up the code nicely
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use the tty baud functions
- Call driver termios methods directly holding the right locking
- Check for a write method
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Operations are now a shared const function block as with most other Linux
objects
- Introduce wrappers for some optional functions to get consistent behaviour
- Wrap put_char which used to be patched by the tty layer
- Document which functions are needed/optional
- Make put_char report success/fail
- Cache the driver->ops pointer in the tty as tty->ops
- Remove various surplus lock calls we no longer need
- Remove proc_write method as noted by Alexey Dobriyan
- Introduce some missing sanity checks where certain driver/ldisc
combinations would oops as they didn't check needed methods were present
[akpm@linux-foundation.org: fix fs/compat_ioctl.c build]
[akpm@linux-foundation.org: fix isicom]
[akpm@linux-foundation.org: fix arch/ia64/hp/sim/simserial.c build]
[akpm@linux-foundation.org: fix kgdb]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver somehow escaped the tty operations changes way back when. Update
it so that we can switch to tty->ops shortly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the following select's:
- RFKILL : IWLWIFI_RFKILL -> IWLCORE
- RFKILL_INPUT : IWLWIFI_RFKILL -> IWLCORE
- MAC80211_LEDS : IWL4965_LEDS -> IWLCORE
- LEDS_CLASS : IWL4965_LEDS -> IWLCORE
- MAC80211_LEDS : IWL3945_LEDS -> IWL3945
- LEDS_CLASS : IWL3945_LEDS -> IWL3945
The effects are:
- with IWLCORE=m and/or IWL3945=m RFKILL/RFKILL_INPUT/MAC80211_LEDS/LEDS_CLASS
are no longer wrongly forced to y
- fixes a build error with IWLCORE=y, IWL4965=m
might be a bug in kconfig causing it, but doing this change that is
anyway the right thing fixes it
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a FMR is unmapped, mlx4 resets the map count to 0, and clears the
upper part of the R_Key which is used as the sequence counter.
This poses a problem for RDS, which uses ib_fmr_unmap as a fence
operation. RDS assumes that after issuing an unmap, the old R_Keys
will be invalid for a "reasonable" period of time. For instance,
Oracle processes uses shared memory buffers allocated from a pool of
buffers. When a process dies, we want to reclaim these buffers -- but
we must make sure there are no pending RDMA operations to/from those
buffers. The only way to achieve that is by using unmap and sync the
TPT.
However, when the sequence count is reset on unmap, there is a high
likelihood that a new mapping will be given the same R_Key that was
issued a few milliseconds ago.
To prevent this, don't reset the sequence count when unmapping a FMR.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Open MPI, Intel MPI and other applications don't respect the iWARP
requirement that the client (active) side of the connection send the
first RDMA message. This class of application connection setup is
called peer-to-peer. Typically once the connection is setup, _both_
sides want to send data.
This patch enables supporting peer-to-peer over the chelsio RNIC by
enforcing this iWARP requirement in the driver itself as part of RDMA
connection setup.
Connection setup is extended, when the peer2peer module option is 1,
such that the MPA initiator will send a 0B Read (the RTR) just after
connection setup. The MPA responder will suspend SQ processing until
the RTR message is received and reply-to.
In the longer term, this will be handled in a standardized way by
enhancing the MPA negotiation so peers can indicate whether they
want/need the RTR and what type of RTR (0B read, 0B write, or 0B send)
should be sent. This will be done by standardizing a few bits of the
private data in order to negotiate all this. However this patch
enables peer-to-peer applications now and allows most of the required
firmware and driver changes to be done and tested now.
Design:
- Add a module option, peer2peer, to enable this mode.
- New firmware support for peer-to-peer mode:
- a new bit in the rdma_init WR to tell it to do peer-2-peer
and what form of RTR message to send or expect.
- process _all_ preposted recvs before moving the connection
into rdma mode.
- passive side: defer completing the rdma_init WR until all
pre-posted recvs are processed. Suspend SQ processing until
the RTR is received.
- active side: expect and process the 0B read WR on offload TX
queue. Defer completing the rdma_init WR until all
pre-posted recvs are processed. Suspend SQ processing until
the 0B read WR is processed from the offload TX queue.
- If peer2peer is set, driver posts 0B read request on offload TX
queue just after posting the rdma_init WR to the offload TX queue.
- Add CQ poll logic to ignore unsolicitied read responses.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Extend the mlx4_cq_resize() API with a way to set the "collapsed" flag
for the CQ being created.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Yeah, in practice they both mean "root", but Alan correctly points out
that anybody who gets to do raw IO space accesses should really be using
CAP_SYS_RAWIO rather than CAP_NET_ADMIN.
Pointed-out-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[RAPIDIO] Change RapidIO doorbell source and target ID field to 16-bit
[RAPIDIO] Add RapidIO connection info print out and re-training for broken connections
[RAPIDIO] Add serial RapidIO controller support, which includes MPC8548, MPC8641
[RAPIDIO] Add RapidIO node probing into MPC86xx_HPCN board id table
[RAPIDIO] Add RapidIO node into MPC8641HPCN dts file
[RAPIDIO] Auto-probe the RapidIO system size
[RAPIDIO] Add OF-tree support to RapidIO controller driver
[RAPIDIO] Add RapidIO multi mport support
[RAPIDIO] Move include/asm-ppc/rio.h to asm-powerpc
[RAPIDIO] Add RapidIO option to kernel configuration
[RAPIDIO] Change RIO function mpc85xx_ to fsl_
[POWERPC] Provide walk_memory_resource() for powerpc
[POWERPC] Update lmb data structures for hotplug memory add/remove
[POWERPC] Hotplug memory remove notifications for powerpc
[POWERPC] windfarm: Add PowerMac 12,1 support
[POWERPC] Fix building of pmac32 when CONFIG_NVRAM=m
[POWERPC] Add IRQSTACKS support on ppc32
[POWERPC] Use __always_inline for xchg* and cmpxchg*
[POWERPC] Add fast little-endian switch system call
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers have duplicated unlikely() macros. IS_ERR() already has
unlikely() in itself.
This patch cleans up such pointless code.
Signed-off-by: Hirofumi Nakagawa <hnakagawa@miraclelinux.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use creation by full path: "driver/foo".
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The error handling for the mpc5200 fec interrupt is broken. The intended
behaviour is like this:
* If one of FEC_IEVENT_RFIFO_ERROR and FEC_IEVENT_XFIFO_ERROR happens,
the datasheet says (MPC5200B User's Guide R1.2, p. 14-13): "When this
occurs, software must ensure both the FIFO Controller and BestComm are
soft-reset".
* On any other error (non-TFINT) interrupt, just issue a debug message.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The RapidIO system size will auto probe in RIO setup. The route table
and rionet_active in rionet.c are changed to be allocated dynamically
according to the size of the system.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
TBIPA needs to be set to a value (on connected MDIO buses) that
doesn't conflict with PHYs on the bus. By hardcoding it to 0x1f,
we were preventing boards with PHYs at 0x1f from working properly.
Instead, scan the bus when it comes up, and find an address that
doesn't have a PHY on it. The TBI PHY configuration code then
trusts that the value in TBIPA is either safe, or doesn't matter
(ie - it's not an active bus with other PHYs).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dev->irq is unsigned, platform_get_irq() may return signed unnoticed
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- replace specific "bf537" function or data structure name to "bfin_mac"
- cleanup bfin_mac_probe with error checking
- punt set_pin_mux function, call peripheral request/free list functions directly
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Found by sparse dubious !x & y warning...hidden in the GetBit macro
why !Word doesn't make any sense.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for two additional SMSC PHY models with identical interrupt
source and mask registers to the LAN83C185
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several models of SMSC PHY have the same interrupt status and mask
registers as the LAN83C185, so these functions can service multiple
different PHY drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix kernel-doc warning:
Warning(linux-2.6.25-git11//drivers/net/phy/phy_device.c:275): No
description found for parameter 'bus_id'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- Seperate ring specific data
- Initialize all configured rings with equal priority.
- Updated boundary check for number of Rings.
- Updated per ring statistics of rx_bytes and rx_packets.
- Moved lro struct from struct s2io_nic to struct ring_info.
- Access respective rx ring directly in fill_rx_buffers.
- Moved rx_bufs_left struct s2io_nic to struct ring_info.
- Added per ring variables - rxd_mode, rxd_count, dev, pdev.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use net_device_stats from net_device structure instead of local.
No need to memset it to 0, because it is allocated by kzalloc.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver supports the 10Xpress PHY and XFP modules on our reference
designs SFE4001 and SFE4002 and the SMC models SMC10GPCIe-XFP and
SMC10GPCIe-10BT.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dev->irq is unsigned, platform_get_irq() may return signed unnoticed
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
iwlwifi: Allow building iwl3945 without iwl4965.
wireless: Fix compile error with wifi & leds
tcp: Fix slab corruption with ipv6 and tcp6fuzz
ipv4/ipv6 compat: Fix SSM applications on 64bit kernels.
[IPSEC]: Use digest_null directly for auth
sunrpc: fix missing kernel-doc
can: Fix copy_from_user() results interpretation
Revert "ipv6: Fix typo in net/ipv6/Kconfig"
tipc: endianness annotations
ipv6: result of csum_fold() is already 16bit, no need to cast
[XFRM] AUDIT: Fix flowlabel text format ambibuity.
The platform is actually named routerboard 532 so let's call it this.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
If IWL3945 ever depends on IWLCORE, the silent, user-invisible
IWLWIFI option can go away.
Signed-off-by: Jason Riedy <jason@acm.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Add helper to move QP to ready-to-send
mlx4_core: Add HW queues allocation helpers
RDMA/nes: Remove volatile qualifier from struct nes_hw_cq.cq_vbase
mlx4_core: CQ resizing should pass a 0 opcode modifier to MODIFY_CQ
mlx4_core: Move kernel doorbell management into core
IB/ehca: Bump version number to 0026
IB/ehca: Make some module parameters bool, update descriptions
IB/ehca: Remove mr_largepage parameter
IB/ehca: Move high-volume debug output to higher debug levels
IB/ehca: Prevent posting of SQ WQEs if QP not in RTS
IPoIB: Handle 4K IB MTU for UD (datagram) mode
RDMA/nes: Fix adapter reset after PXE boot
RDMA/nes: Print IPv4 addresses in a readable format
RDMA/nes: Use print_mac() to format ethernet addresses for printing
... and isn't possible on sparc32 boxen anyway, unless somebody
had done JavaStation with PCIE lately.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It does not help the auto-negotiation process to settle.
Added a debug message to give some hindsight when things
do not work as expected.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
- remove the function pointer to help gcc optimizing the
inline pci_dma functions
- pci_dma_sync_single_for_cpu is not needed for a single
large packet
- convert rtl8169_try_rx_copy to bool
b449655ff5 did the same
for the r8169 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
This sets skb->dev and allows arch specific allocation.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
There is no DMA involved here. Align the IP header without condition.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
The local status code does not carry mory information.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Avoid duplicating code in ethernet and FC modules.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Wrap doorbell, buffer and MTT allocation in helper functions for
ethernet and FC modules to use.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (49 commits)
[POWERPC] Add zImage.iseries to arch/powerpc/boot/.gitignore
[POWERPC] bootwrapper: fix build error on virtex405-head.S
[POWERPC] 4xx: Fix 460GT support to not enable FPU
[POWERPC] 4xx: Add NOR FLASH entries to Canyonlands and Glacier dts
[POWERPC] Xilinx: of_serial support for Xilinx uart 16550.
[POWERPC] Xilinx: boot support for Xilinx uart 16550.
[POWERPC] celleb: Add support for PCI Express
[POWERPC] celleb: Move miscellaneous files for Beat
[POWERPC] celleb: Move a file for SPU on Beat
[POWERPC] celleb: Move files for Beat mmu and iommu
[POWERPC] celleb: Move files for Beat hvcall interfaces
[POWERPC] celleb: Move the SCC related code for celleb
[POWERPC] celleb: Move the files for celleb base support
[POWERPC] celleb: Consolidate io-workarounds code
[POWERPC] cell: Generalize io-workarounds code
[POWERPC] Add CONFIG_PPC_PSERIES_DEBUG to enable debugging for platforms/pseries
[POWERPC] Convert from DBG() to pr_debug() in platforms/pseries/
[POWERPC] Register udbg console early on pseries LPAR
[POWERPC] Mark udbg console as CON_ANYTIME, ie. callable early in boot
[POWERPC] Set udbg_console index to 0
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-xen-next: (52 commits)
xen: add balloon driver
xen: allow compilation with non-flat memory
xen: fold xen_sysexit into xen_iret
xen: allow set_pte_at on init_mm to be lockless
xen: disable preemption during tlb flush
xen pvfb: Para-virtual framebuffer, keyboard and pointer driver
xen: Add compatibility aliases for frontend drivers
xen: Module autoprobing support for frontend drivers
xen blkfront: Delay wait for block devices until after the disk is added
xen/blkfront: use bdget_disk
xen: Make xen-blkfront write its protocol ABI to xenstore
xen: import arch generic part of xencomm
xen: make grant table arch portable
xen: replace callers of alloc_vm_area()/free_vm_area() with xen_ prefixed one
xen: make include/xen/page.h portable moving those definitions under asm dir
xen: add resend_irq_on_evtchn() definition into events.c
Xen: make events.c portable for ia64/xen support
xen: move events.c to drivers/xen for IA64/Xen support
xen: move features.c from arch/x86/xen/features.c to drivers/xen
xen: add missing definitions in include/xen/interface/vcpu.h which ia64/xen needs
...
- vlans were using a single CAM register (see mac_set_vlan_cam)
- setting the address filtering registers for vlans is not
needed when there is no vlan
The non-tagged interface is filtered out as soon as a tagged
(!= 0) interface is created. Its traffic appears again when an
zero-tagged interface is created.
Tested on Via Epia SN (VT6130 chipset) with several vlans whose
tag was above or beyond 255.
Signed-off-by: Séguier Régis <rseguier@e-teleport.net>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the following sparse warning :
drivers/net/tg3.c:4025:3: warning: context imbalance in 'tg3_restart_hw'
- unexpected unlock
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue seen with the realtek 8201 phy. This phy has a
problem with crossover detection and it needs to be disabled. The
problem only arises on certain switches. Therefore, a module parameter
has been added to allow enabling crossover detection if needed. The
default will be set to disabled.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch doubles the MDIO timeouts in EMAC as there are field
cases where they are two short to communicate with some PHYs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
gianfar was unable to handle failed skb allocation for rx buffers, so
we were spinning until it succeeded. Actually, it was worse--we were
spinning for a long time, and then silently failing. Instead, we take
Stephen Hemminger's suggestion to try the allocation earlier, and drop the
packet if it failed.
We also make a couple of tweaks to how buffer descriptors are set up.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Don't need to keep a struct netxen_new_user_info on the stack
when we only are interested in printing the serial_num. Change
to only reading the serial_num.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When timeout reaches 0 the postfix decrement still subtracts, so the test
fails.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable network
platform drivers, to re-enable auto loading.
NOTE: didn't change drivers/net/fs_enet/fs_enet-main.c "old binding" support.
That looks problematic in the first place (it even uses the ancient "struct
device_driver" binding scheme for platform_bus!) and I suspect it will vanish
soonish when arch/powerpc rules the world. Also, drivers/net/ne.c would have
needed more thought to sort out.
[akpm@linux-foundation.org: fix sgiseeq.c]
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for a new backoff algorithm for half duplex supported
in newer hardware. The old method is will be designated as legacy mode.
Re-seeding random values for the backoff algorithms are performed when a
transmit has failed due to a maximum retry count (1 to 15, where max is
considered the wraparound case of 0).
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ehea_flush_sq() and ehea_purge_sq() should be static.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Thomas Klein <osstklei@de.ibm.com>
Cc: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sometimes the specific interaction between the platform and the PHY
requires special handling. For instance, to change where the PHY's
clock input is, or to add a delay to account for latency issues in the
data path. We add a mechanism for registering a callback with the PHY
Lib to be called on matching PHYs when they are brought up, or reset.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move some code from atlx.c to atl1.c to prevent build conflict with
the upcoming atl2 code. No changes, just movement.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no good reason to manually set the flash vendor in a module
parameter, outside of an Atheros hardware lab. Remove it, so nobody
accidentally bricks their board using it incorrectly.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- useless initialization (korina_ope / korina_restart)
- use a single variable for the status code in korina_probe
and propagate the error status code from below
- useless checks in korina_remove : the variables are
necessarily set when korina_probe succeeds
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver takes the error unwind path without condition.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The local variable "prefix" is never used anymore, and the content of
this string appears a bit later, directly in a call to "alloc_netdev"
after doing exactly the same if/else test. So there seems to be no
point keeping those 4 lines anymore.
Signed-off-by: Cédric Augonnet <cedric.augonnet@ens-lyon.org>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
While trying to fix http://bugzilla.kernel.org/show_bug.cgi?id=8952
I looked at a few other drivers to figure out what drivers _should_
be doing for suspend/resume. I noticed typhoon driver is likely doing
more than it needs to. Patch below is untested since I don't have the HW.
Suspend/resume code across NIC drivers is fairly inconsistent.
And I couldn't find any documentation on what the canonical sequence
NICs need to do for suspend or resume. Is there any?
Barring contrary advice, I'm going model the tulip suspend/resume
fixes after tg3.c since a number of "modern" (< 5 years old) laptops
have that and I'm silly enough to assume it works.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds ibm_newemac PHY clock workaround for 440EP/440GR EMAC
attached to a PHY which doesn't generate RX clock if there is no link.
The code is based on the previous ibm_emac driver stuff. The 440EP/440GR
allows controlling each EMAC clock separately as opposed to global clock
selection for 440GX.
BenH: Made that #ifdef CONFIG_PPC_DCR_NATIVE for now as dcri_* stuff doesn't
exist for MMIO type DCRs like Cell. Some future rework & improvements of the
DCR infrastructure will make that cleaner but for now, this makes it work.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The PowerPC 440GX Taishan board fails to reset EMAC3 (reset timeout
error) if there's no link. Because of that it fails to find PHY
chip. The older ibm_emac driver had a workaround for that: the
EMAC_CLK_INTERNAL/EMAC_CLK_EXTERNAL macros, which toggle the Ethernet
Clock Select bit in the SDR0_MFR register. This patch does the same for
"ibm,emac-440gx" compatible chips. The workaround forces clock on -all-
EMACs, so we select clock under global emac_phy_map_lock.
BenH: Made that #ifdef CONFIG_PPC_DCR_NATIVE for now as dcri_* stuff
doesn't exist for MMIO type DCRs like Cell. Some future rework &
improvements of the DCR infrastructure will make that cleaner but
for now, this makes it work.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert ibm_newemac to use the of_device_is_available function when checking
for unused/unwired EMACs. We leave the current check for an "unused" property
to maintain backwards compatibility for older device trees. Newer device
trees should simply use the standard "status" property in the EMAC node.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes several section mismatch warnings in the
ibm_newemac driver similar to:
WARNING: vmlinux.o(.devinit.text+0x3a04): Section mismatch in reference from the function emac_probe() to the function .devexit.text:tah_detach()
The function __devinit emac_probe() references
a function __devexit tah_detach().
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On some 4xx PPC's (e.g. 460EX/GT), the rx channel number is a multiple
of 8 (e.g. 8 for EMAC1, 16 for EMAC2), but enabling in MAL_RXCASR needs
the divided by 8 value for the bitmask.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This fixes the jumbo frame support on EMAC V4 systems. Now the correct
bit is set depending on the EMAC version configured.
Tested on Kilauea (405EX) and Canyonlands (460EX).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To enable EEH support for pci-express network adapters, pcie/msi state
needs to be saved and restored for that adapter.
[after similar patches for ixgbe and e1000e from Wendy Xiong]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To enable EEH support for pci-express network adapters, pcie/msi state
needs to be saved and restored for that adapter.
Tested this EEH patch with 2ports and 4ports pci-express e1000e
adapters.
Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To enable EEH support for pci-express network adapters, pcie/msi state
needs to be saved and restored for that adapter.
Tested this EEH patch with Intel 10G pci-express ixgbe adapter.
Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The lower limit of 80 descriptors in the ring is only valid for
one older 8254x chipset. All e1000e devices can use as low as
64 descriptors.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several components to this complex fix. The es2lan cards occasionally
gave a "HW Error" especially when forcing speed. Some users also
reported that the BMC stole ARP packets.
The fixes include setting the proper SW_FW bits to tell the BMC
that we're active and not do any un-initialization at all, so the
setup routine is largely changed.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ethtool -c / -C interface can now be used to modify the
irq moderation algorithm. This change does not require an
adapter reset and can thus be used at all times. The adapter
only supports changing/reading rx-usecs which has special
values for 0, 1 and 3:
0 - no irq moderation whatsoever
1 - normal moderation favoring regular mixed traffic (default)
3 - best attempt at low latency possible at cost of CPU
For values between 10 and 10000 the rx-usecs defines "the minimum
time between successive irqs" in usec, unlike the module parameter.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several stats registers are completely unused and we just waste pci
bus time reading them. We also omit using the high 32 bits of the GORC/
GOTC counters. We can just read clear them and only read the low registers.
Mii-tool can also break es2lan if it executes a MII PHY register
ioctl while the device is in autonegotiation. Unfortunately it seems
that several applications and installations still perform this ioctl
call periodically and especially in this crucial startup time. We
can fool the ioctl by providing fail safe information that mimics
the "down" link state and only perform the dangerous PHY reads once
after link comes up to fill in the real values. As long as link
stays up the information will not change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- Removed receive buffer replenishment tasklet s2io_tasklet and instead
allocating the receive buffers in either the interrupt handler (no napi)
or the napi handler (napi enabled).
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The patch that changed mdio_bus to a string didn't conflict strongly enough
with the patch that added fixed PHY support to UCC. Gather it back into
the fold.
Fixes this error:
...
CC drivers/net/ucc_geth.o
'ucc_geth_probe':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/net/ucc_geth.c:3935: error:
incompatible types in assignment
make[3]: *** [drivers/net/ucc_geth.o] Error 1
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[ Minor coding style and whitespace corrections, also bump
driver version and release date. -DaveM ]
Signed-off-by: Matheos Worku <matheos.worku@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Fix minor whitespace and coding style stuff... -DaveM ]
Signed-off-by: Matheos Worku <matheos.worku@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before getting merged, xen-blkfront was xenblk and
xen-netfront was xennet.
Temporarily adding compatibility module aliases
eases upgrades from older versions by e.g. allowing
mkinitrd to find the new version of the module.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add module aliases to support autoprobing modules
for xen frontend devices.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (85 commits)
Blackfin char driver for Blackfin on-chip OTP memory (v3)
Blackfin Serial Driver: fix bug - use mod_timer to replace only add_timer.
Blackfin Serial Driver: the uart break anomaly has been given its own number, so switch to it
Blackfin Serial Driver: use BFIN_UART_NR_PORTS to help SIR driver in uart port.
Blackfin Serial Driver: Fix bug - kernel hangs when accessing uart 0 on bf537 when booting u-boot and linux on uart 1
Blackfin Serial Driver: punt unused lsr variable
Blackfin Serial Driver: Enable IR function when user application (irattach /dev/ttyBFx -s) call TIOCSETD ioctl with line discipline N_IRDA
[Blackfin] arch: add include/boot .gitignore files
[Blackfin] arch: Functional power management support: Add support for cpu frequency scaling
[Blackfin] arch: Functional power management support: Remove broken cpu frequency scaling drivers
[Blackfin] arch: Equalize include files: Add PLL_DIV Masks
[Blackfin] arch: Add a warning about the value of CLKIN.
[Blackfin] arch: take DDR DEVWD into consideration as well for BF548
[Blackfin] arch: Remove the circular buffering mechanism for exceptions
[Blackfin] arch: lose unnecessary dependency on CONFIG_BFIN_ICACHE for MPU
[Blackfin] arch: fix bug - before assign new channel to the map register, need clear the bits first.
[Blackfin] arch: add Blackfin on-chip SIR IrDA driver support
[Blackfin] arch: BF54x memsizes are in mbits, not mbytes
[Blackfin] arch: try to remove condition that causes double fault, by checking current before it gets dereferenced
[Blackfin] arch: Update anomaly list.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (22 commits)
tun: Multicast handling in tun_chr_ioctl() needs proper locking.
[NET]: Fix heavy stack usage in seq_file output routines.
[AF_UNIX] Initialise UNIX sockets before general device initcalls
[RTNETLINK]: Fix bogus ASSERT_RTNL warning
iwlwifi: Fix built-in compilation of iwlcore (part 2)
tun: Fix minor race in TUNSETLINK ioctl handling.
ppp_generic: use stats from net_device structure
iwlwifi: Don't unlock priv->mutex if it isn't locked
wireless: rndis_wlan: modparam_workaround_interval is never below 0.
prism54: prism54_get_encode() test below 0 on unsigned index
mac80211: update mesh EID values
b43: Workaround DMA quirks
mac80211: fix use before check of Qdisc length
net/mac80211/rx.c: fix off-by-one
mac80211: Fix race between ieee80211_rx_bss_put and lookup routines.
ath5k: Fix radio identification on AR5424/2424
ssb: Fix all-ones boardflags
b43: Add more btcoexist workarounds
b43: Fix HostFlags data types
b43: Workaround invalid bluetooth settings
...
The PS3 gelic network driver depends on the wake-on-lan support
provided by the PS3 sys manager driver. Add that dependency
to the GELIC_NET Kconfig option.
Prevents these build errors:
ps3_gelic_net.c:1277: undefined reference to `.ps3_sys_manager_get_wol'
ps3_gelic_net.c:1337: undefined reference to `.ps3_sys_manager_set_wol'
CC: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since these operations don't go through the normal
device calls, we have to ensure we synchronize with
those paths.
Noticed by Alan Cox.
Signed-off-by: David S. Miller <davem@davemloft.net>
On Wed, 2008-04-23 at 13:38 +0300, Tomas Winkler wrote:
> This patch fixes problem in Makefile that prevented
> built-in compilation of iwlcore
Here is the second part. Without this,
drivers/net/wireless/iwlwifi/build-in.o will not be linked into vmlinux.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed by Alan Cox.
The IFF_UP test is a bit racey, because other entities
outside of this driver's ioctl handler can modify that
state, even though this ioctl handler runs under
lock_kernel().
Signed-off-by: David S. Miller <davem@davemloft.net>
Use stats which now is in the net_device instead of one declared in
ppp structure.
Kill ppp_net_stats function, because by default it is used identical
internal_stats function from net/core/dev.c
Signed-of-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b716bb91 ("iwlwifi: Cancel scanning upon association") moved the
test of priv->vif in iwl{3945,4964}_mac_config_interface() outside of
where priv->mutex is held, but still tries to do mutex_unlock() on
return. This is clearly wrong and triggers a nasty lockdep warning when
this codepath is triggered. Fix this by removing the mutex_unlock().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->param_workaround_interval is unsigned, modparam_workaround_interval not.
the former is never < 0.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
previously in this function:
u32 index = (dwrq->flags & IW_ENCODE_INDEX) - 1;
index is unsigned, so if -1, the original test (below) didn't work.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some mainboards/CPUs don't allow DMA masks bigger than a certain limit.
Some VIA crap^h^h^h^hdevices have an upper limit of 0xFFFFFFFF. So in this
case a 64-bit b43 device would always fail to acquire the mask.
Implement a workaround to fallback to lower DMA mask, as we can always
also support a lower mask.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
*Fix radio chip identification on AR5424/2424 during ath5k_hw_attach
*Try to assign an RF2413 radio on AR2424 for testing
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds more workarounds for devices with broken BT bits.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HostFlags are a bitmask of 48bit. So we must use an u64 datatype
to hold all bits.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a workaround for invalid bluetooth SPROM settings
on ASUS PCI cards.
This will stop the microcode from poking with the BT GPIO line.
This fixes data transmission on this device, as the BT GPIO line
is used for something TX related on this device
(probably the power amplifier or the radio).
This also adds a modparam knob to help debugging this in the future,
as more devices with this bug may show up.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
iwlwifi: Fix built-in compilation of iwlcore
net: Unexport move_addr_to_{kernel,user}
rt2x00: Select LEDS_CLASS.
iwlwifi: Select LEDS_CLASS.
leds: Do not guard NEW_LEDS with HAS_IOMEM
[IPSEC]: Fix catch-22 with algorithm IDs above 31
time: Export set_normalized_timespec.
tcp: Make use of before macro in tcp_input.c
hamradio: Remove unneeded and deprecated cli()/sti() calls in dmascc.c
[NETNS]: Remove empty ->init callback.
[DCCP]: Convert do_gettimeofday() to getnstimeofday().
[NETNS]: Don't initialize err variable twice.
[NETNS]: The ip6_fib_timer can work with garbage on net namespace stop.
[IPV4]: Convert do_gettimeofday() to getnstimeofday().
[IPV4]: Make icmp_sk_init() static.
[IPV6]: Make struct ip6_prohibit_entry_template static.
tcp: Trivial fix to correct function name in a comment in net/ipv4/tcp.c
[NET]: Expose netdevice dev_id through sysfs
skbuff: fix missing kernel-doc notation
[ROSE]: Fix soft lockup wrt. rose_node_list_lock
The call to mlx4_MODIFY_CQ() had a typo so that mlx4_cq_resize() was
actually asking the FW to modify a CQ's interrupt moderation rather than
asking it to resize a CQ.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In addition to mlx4_ib, there will be ethernet and FC consumers of
mlx4_core, so move the code for managing kernel doorbells into the
core module to avoid having to duplicate this multiple times.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes problem in Makefile that prevented
built-in compilation of iwlcore
Commit that caused this problem: eadd3c4b ("iwlwifi: make Makefile
more concise")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Yi Zhu <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
rose: Socket lock was not released before returning to user space
hci_usb: remove code obfuscation
drivers/net/appletalk: use time_before, time_before_eq, etc
drivers/atm: use time_before, time_before_eq, etc
hci_usb: do not initialize static variables to 0
tg3: 5701 DMA corruption fix
atm nicstar: Removal of debug code containing deprecated calls to cli()/sti()
iwlwifi: Fix unconditional access to station->tidp[].agg.
netfilter: Fix SIP conntrack build with NAT disabled.
netfilter: Fix SCTP nat build.
