The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forgot to cancel all timers in mac80211 when suspending.
In particular we forgot to deal with some things that can
cause hardware reconfiguration -- while it is down.
While at it we go ahead and add a warning in ieee80211_sta_work()
if its run while the suspend->resume cycle is in effect. This
should not happen and if it does it would indicate there is
a bug lurking in either mac80211 or mac80211 drivers.
With this now wpa_supplicant doesn't blink when I go to suspend
and resume where as before there where issues with some timers
running during the suspend->resume cycle. This caused a lot of
incorrect assumptions and would at times bring back the device
in an incoherent, but mostly recoverable, state.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all the code from mac80211 to keep track of BSSes
and use the cfg80211-provided code completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the standards only define 12 legacy rates, 32 is certainly
a sane upper limit and we don't need to use u64 everywhere. Add
sanity checking that no more than 32 rates are registered and
change the variables to u32 throughout.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes documentation of enum mesh_path_flags in mesh.h.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes mesh_plink_close() method as it is unused.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a constant from the 802.11 specification.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the mesh code doesn't support bridging mesh point interfaces
with wired ethernet or AP to construct an MPP or MAP. This patch adds
code to support the "6 address frame format packet" functionality to
mesh point interfaces. Now the mesh network can be used as backhaul
for end to end communication.
Signed-off-by: Li YanBo <dreamfly281@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits off mesh handling from the STA/IBSS.
Unfortunately it increases mesh code size a bit, but I
think it makes things clearer. The patch also reduces
per-interface run-time memory usage.
Also clean up a few places where ifdef is not required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces net_device arguments to mac80211 internal functions
with ieee80211_{local,sub_if_data} as appropriate.
It also does the same for many 802.11s mesh functions, and changes the
mesh path table to be indexed on sub_if_data rather than net_device.
If the mesh part needs to be a separate patch let me know, but since
mesh uses a lot of mac80211 functions which were being converted anyway,
the changes go hand-in-hand somewhat.
This patch probably does not convert all the functions which could be
converted, but it is a large chunk and followup patches will be
provided.
Signed-off-by: Jasper Bryant-Greene <jasper@amiton.co.nz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we deal with mesh forwarding before the 802.11->802.3 conversion, thus
eliminating a few unnecessary steps. The next hop lookup is called from
ieee80211_master_start_xmit() instead of subif_start_xmit(). Until the next hop
is found, RA in the frame will be all zeroes for frames originating from the
device. For forwarded frames, RA will contain the TA of the received frame,
which will be necessary to send a path error if a next hop is not found.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mesh_path_node_copy() performs kmalloc() and thus - may fail
(well, it does not now, but I'm fixing this right now). Its caller -
the mesh_table_grow() - isn't prepared for such a trick yet.
This preparation is just flush the new hash and make copy_node()
return an int value.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 6c4711b469.
That patch breaks mesh config comparison between beacons/probe reponses, so
every beacon from a mesh network would be added as a new bss. Since the
comparison has to be performed for every received beacon I believe it is best to
save the mesh config in a format easy to compare, rather than do a bunch of
unaligned accesses to compare field by field.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows cleaner code when accesing bss->mesh_config components.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Postponing the deletion is not really useful anymore.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a bug I introduced when mesh is enabled: sta_info_destroy()
will end up calling cancel_timer() on a timer that has never been
initialized because the timer is only initialized in mesh_plink_alloc(),
not in sta_info_alloc(). This patch moves the initialization of all mesh
related fields into sta_info_alloc(), adds a bit of sanity checking to
the cfg80211 handlers and sta_info_insert() and makes mesh_plink_alloc()
a static helper function that is only used from the mesh plink code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_info_add() has two functions: allocating a station info
structure and inserting it into the hash table/list. Splitting
these two functions allows allocating with GFP_KERNEL in many
places instead of GFP_ATOMIC which is now required by the RCU
protection. Additionally, in many places RCU protection is now
no longer needed at all because between sta_info_alloc() and
sta_info_insert() the caller owns the structure.
This fixes a few race conditions with setting initial flags
and similar, but not all (see comments in ieee80211_sta.c and
cfg.c). More documentation on the existing races will be in
a follow-up patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes access to the STA hash table/list use RCU to protect
against freeing of items. However, it's not a true RCU, the
copy step is missing: whenever somebody changes a STA item it
is simply updated. This is an existing race condition that is
now somewhat understandable.
This patch also fixes the race key freeing vs. STA destruction
by making sure that sta_info_destroy() is always called under
RTNL and frees the key.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various cleanups, reducing the #ifdef mess and other things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
