This patch renames hdev->extfeatures to hdev->host_features since it
holds the extended features Page 1 (aka host features).
Signed-off-by: Andre Guedes <aguedespe@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We should not forget to try for real server with port 0
in the backup server when processing the sync message. We should
do it in all cases because the backup server can use different
forwarding method.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
During some debugging I needed to look into how /proc/net/ipv6_route
operated and in my digging I found its calling fib6_clean_all() which uses
"write_lock_bh(&table->tb6_lock)" before doing the walk of the table. I
found this on 2.6.32, but reading the code I believe the same basic idea
exists currently. Looking at the rtnetlink code they are only calling
"read_lock_bh(&table->tb6_lock);" via fib6_dump_table(). While I realize
reading from proc isn't the recommended way of fetching the ipv6 route
table; taking a write lock seems unnecessary and would probably cause
network performance issues.
To verify this I loaded up the ipv6 route table and then ran iperf in 3
cases:
* doing nothing
* reading ipv6 route table via proc
(while :; do cat /proc/net/ipv6_route > /dev/null; done)
* reading ipv6 route table via rtnetlink
(while :; do ip -6 route show table all > /dev/null; done)
* Load the ipv6 route table up with:
* for ((i = 0;i < 4000;i++)); do ip route add unreachable 2000::$i; done
* iperf commands:
* client: iperf -i 1 -V -c <ipv6 addr>
* server: iperf -V -s
* iperf results - 3 runs each (in Mbits/sec)
* nothing: client: 927,927,927 server: 927,927,927
* proc: client: 179,97,96,113 server: 142,112,133
* iproute: client: 928,927,928 server: 927,927,927
lock_stat shows taking the write lock is causing the slowdown. Using this
info I decided to write a version of fib6_clean_all() which replaces
write_lock_bh(&table->tb6_lock) with read_lock_bh(&table->tb6_lock). With
this new function I see the same results as with my rtnetlink iperf test.
Signed-off-by: Josh Hunt <joshhunt00@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tcp diag reports rqlen and wqlen values similar to how
the CINQ/COUTQ iotcls do. To make unix diag report these values
in the same way move the respective code into helpers.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It just obscures that the netdevice pointer and the expires value are
implemented in the dst_entry sub-object of the ipv6 route.
And it makes grepping for dst_entry member uses much harder too.
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, create and use an rt6_bind_neighbour() in net/ipv6/route.c to
consolidate some common logic.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to perform a proper universal hash on a vector of integers,
we have to use different universal hashes on each vector element.
Which means we need 4 different hash randoms for ipv6.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
The NAT range to nlattr conversation callbacks and helpers are entirely
dead code and are also useless since there are no NAT ranges in conntrack
context, they are only used for initially selecting a tuple. The final NAT
information is contained in the selected tuples of the conntrack entry.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The only remaining user of NAT protocol module reference counting is NAT
ctnetlink support. Since this is a fairly short sequence of code, convert
over to use RCU and remove module reference counting.
Module unregistration is already protected by RCU using synchronize_rcu(),
so no further changes are necessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Export the NAT definitions to userspace. So far userspace (specifically,
iptables) has been copying the headers files from include/net. Also
rename some structures and definitions in preparation for IPv6 NAT.
Since these have never been officially exported, this doesn't affect
existing userspace code.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This partially reworks bc01befdcf
which added userspace expectation support.
This patch removes the nf_ct_userspace_expect_list since now we
force to use the new iptables CT target feature to add the helper
extension for conntracks that have attached expectations from
userspace.
A new version of the proof-of-concept code to implement userspace
helpers from userspace is available at:
http://people.netfilter.org/pablo/userspace-conntrack-helpers/nf-ftp-helper-POC.tar.bz2
This patch also modifies the CT target to allow to set the
conntrack's userspace helper status flags. This flag is used
to tell the conntrack system to explicitly allocate the helper
extension.
This helper extension is useful to link the userspace expectations
with the master conntrack that is being tracked from one userspace
helper.
This feature fixes a problem in the current approach of the
userspace helper support. Basically, if the master conntrack that
has got a userspace expectation vanishes, the expectations point to
one invalid memory address. Thus, triggering an oops in the
expectation deletion event path.
I decided not to add a new revision of the CT target because
I only needed to add a new flag for it. I'll document in this
issue in the iptables manpage. I have also changed the return
value from EINVAL to EOPNOTSUPP if one flag not supported is
specified. Thus, in the future adding new features that only
require a new flag can be added without a new revision.
There is no official code using this in userspace (apart from
the proof-of-concept) that uses this infrastructure but there
will be some by beginning 2012.
Reported-by: Sam Roberts <vieuxtech@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
skb->truesize might be big even for a small packet.
Its even bigger after commit 87fb4b7b53 (net: more accurate skb
truesize) and big MTU.
We should allow queueing at least one packet per receiver, even with a
low RCVBUF setting.
Reported-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They don't need to disable interrupts anymore, we only run in process
context now.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We simply say that regular this_cpu use must be safe regardless of
preemption and interrupt state. That has no material change for x86
and s390 implementations of this_cpu operations. However, arches that
do not provide their own implementation for this_cpu operations will
now get code generated that disables interrupts instead of preemption.
-tj: This is part of on-going percpu API cleanup. For detailed
discussion of the subject, please refer to the following thread.
http://thread.gmane.org/gmane.linux.kernel/1222078
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
LKML-Reference: <alpine.DEB.2.00.1112221154380.11787@router.home>
To achive Man-In-The-Middle (MITM) level security with Low Energy,
we have to enable User Passkey Comparison. This commit modifies the
hard-coded JUST-WORKS pairing mechanism to support query via the MGMT
interface of Passkey comparison and User Confirmation.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Acked-by: Marcel Holtmann<marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The struct hci_proto and all related register/unregister and dispatching
code was removed. HCI core code now call directly the SCO and L2CAP
event functions.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Make code readable by removing magic numbers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
flow_cach_flush() might sleep but can be called from
atomic context via the xfrm garbage collector. So add
a flow_cache_flush_deferred() function and use this if
the xfrm garbage colector is invoked from within the
packet path.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
to record the state of SACK/FACK and DSACK for better readability and maintenance.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handling of SCO audio links and the L2CAP protocol are essential to
any system with Bluetooth thus are always compiled in from now on.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
It makes more sense this way, since info_timer is a timer using delayed
work API.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This one also needs to run in process context
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
af_iucv differs unnecessarily between state IUCV_SEVERED and
IUCV_DISCONN. This patch removes state IUCV_SEVERED.
While simplifying af_iucv, this patch removes the 2nd invocation of
cpcmd as well.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
af_iucv contains timer infrastructure which is not exploited.
This patch removes the timer related code parts.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8ffd3208 voids the previous patches f6778aab and 810c0719 for
limiting the autoclose value. If userspace passes in -1 on 32-bit
platform, the overflow check didn't work and autoclose would be set
to 0xffffffff.
This patch defines a max_autoclose (in seconds) for limiting the value
and exposes it through sysctl, with the following intentions.
1) Avoid overflowing autoclose * HZ.
2) Keep the default autoclose bound consistent across 32- and 64-bit
platforms (INT_MAX / HZ in this patch).
3) Keep the autoclose value consistent between setsockopt() and
getsockopt() calls.
Suggested-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 5c3ddec73d.
S390 qeth driver actually still uses the setup ops.
Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a peer changes SMPS state we should update
rate control so it doesn't have to detect it by
itself. It can't detect "dynamic" mode anyway
since that just requires rts-cts handshaking.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If station info contains a beacon loss count, return
it to userspace.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the necessary structs for the Confirm Name command. This
ensures that the protocol definitions are up to date with the latest
mgmt specification. The actual implementation of the command will follow
in a later patch-set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch fixes the opcodes of the Block/Unblock device commands to
match with what user-space expects and to confirm with the latest mgmt
specification. The reason the values were wrong was a missing Confirm
Name command definition (which will be added by a subsequent patch).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a missing confirm_name field to mgmt_ev_device_found.
Support for setting the correct value for this field is not implemented
yet, but having it part of the struct definition ensures that user-space
gets correct sized device_found events and is thereby able to do at
least rudimentary parsing of them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Implement block size read function. Use different variables for
packet-based and block-based flow control.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch updates the ordering and opcodes of mgmt messages to match
the latest API specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We do not want the service cache to be enabled indefinitely after
mgmt_read_info is called. To solve this a timer is added which will
automatically disable the cache if mgmt_set_dev_class isn't called
within 5 seconds of calling mgmt_read_info.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Instead of having an explicit service cache command we can make the mgmt
API simpler by implicitly enabling the cache when mgmt_read_info is
called for the first time and disabling it when mgmt_set_dev_class is
called.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Fast connectable is logically after the connectable property so that's
where it should show up in the code as well (it's also after connectable
in the settings bitfield).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch updates the mgmt_read_info and related messages to the latest
management API which uses a bitfield of settings instead of individual
boolean values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As we run in process context now we don't need worqueue to add e del from
sysfs.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This move some checking code that was in l2cap_sock_connect() to
l2cap_chan_connect(). Thus we can invert the lock calls, i.e., call
lock_sock() before hci_dev_lock() to avoid a deadlock scenario.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Another step of remove interrupt context from Bluetooth Core.
Use the system workqueue.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This should simplify Bluetooth core processing a lot.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As part of the moving on all the Bluetooth processing to Process context.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Handling hci_conn_hash with RCU make us avoid some locking and disable
tasklets.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
spin lock doesn't fit ok anymore on the new code based on workqueues.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
L2CAP timers also need to run in process context. As the works in l2cap
are small we are using the system worqueue.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As HCI rx path is now done in process context it makes sense to do all the
timer in process context as well.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth rx task runs now in a workqueue, so it a good approach run any
timer that share locking with process context code also in a workqueue.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Now we run everything in HCI in process context, so it's a better idea use
mutex instead spin_lock. The macro remains hci_dev_lock() (and I got rid
of hci_dev_lock_bh()), of course.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Run recv process in workqueue helps a lot with our processing as the recv
path will also be in the process context, i.e., now all our tx and rx are
in process context.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We can use atomic64_t infrastructure to avoid taking a spinlock in fast
path, and remove inaccuracies while reading values in
ctnetlink_dump_counters() and connbytes_mt() on 32bit arches.
Suggested by Pablo.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Glauber Costa <glommer@parallels.com>
CC: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com>
CC: David S. Miller <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
By definition WIPHY_FLAG_STRICT_REGULATORY was intended to allow the
wiphy to adjust itself to the country IE power information if the
card had no regulatory data but we had no way to tell cfg80211 that if
the card also had its own custom regulatory domain (these are typically
custom world regulatory domains) that we want to follow the country IE's
noted values for power for each channel. We add support for this and
document it.
This is not a critical fix but a performance optimization for cards
with custom regulatory domains that associate to an AP with sends
out country IEs with a higher EIRP than the one on the custom
regulatory domain. In practice the only driver affected right now
are the Atheros drivers as they are the only drivers using both
WIPHY_FLAG_STRICT_REGULATORY and WIPHY_FLAG_CUSTOM_REGULATORY --
used on cards that have an Atheros world regulatory domain. Cards
that have been programmed to follow a country specifically will not
follow the country IE power. So although not a stable fix distributions
should consider cherry picking this.
Cc: compat@orbit-lab.org
Cc: Paul Stewart <pstew@google.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Senthilkumar Balasubramanian <senthilb@qca.qualcomm.com>
Reported-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 station handling code is a bit messy
and doesn't do a lot of validation. It seems like
this could be an issue for drivers that don't use
mac80211 to validate everything.
As cfg80211 doesn't keep station state, move the
validation of allowing supported_rates to change
for TDLS only in station mode to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without an API for setting and getting the local and remote general bytes,
drivers won't be able to properly establish a DEP link.
This API also allows them to propagate the remote general bytes they get
from the DEP link establishment up to the LLCP layer.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NFC-DEP (Data Exchange Protocol) is an NFC MAC layer.
This command allows to enable and disable the DEP link on to which e.g.
LLCP can run.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a factorization of the current rawsock tx skb allocation routine,
as it will be used by the LLCP code.
We also rename nfc_alloc_skb to nfc_alloc_recv_skb for consistency sake.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit b099ce2602 (net: Batch inet_twsk_purge) added rcu protection
on tw_net for no obvious reason.
struct net are refcounted anyway since timewait sockets escape from rcu
protected sections. tw_net stay valid for the whole timwait lifetime.
This also removes a lot of sparse errors.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's simpler to just keep these things out until there is a real user
of them, so we can see what the needs actually are, rather than keep
these things around as useless overhead.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is quite possible to run into a race in bss timeout where
the drivers see the bss entry just before notifying cfg80211
of a roaming event but it got timed out by the time rdev->event_work
got scehduled from cfg80211_wq. This would result in the following
WARN-ON() along with the failure to notify the user space of
the roaming. The other situation which is happening with ath6kl
that runs into issue is when the driver reports roam to same AP
event where the AP bss entry already got expired. To fix this,
move cfg80211_get_bss() from __cfg80211_roamed() to cfg80211_roamed().
[158645.538384] WARNING: at net/wireless/sme.c:586
__cfg80211_roamed+0xc2/0x1b1()
[158645.538810] Call Trace:
[158645.538838] [<c1033527>] warn_slowpath_common+0x65/0x7a
[158645.538917] [<c14cfacf>] ? __cfg80211_roamed+0xc2/0x1b1
[158645.538946] [<c103354b>] warn_slowpath_null+0xf/0x13
[158645.539055] [<c14cfacf>] __cfg80211_roamed+0xc2/0x1b1
[158645.539086] [<c14beb5b>] cfg80211_process_rdev_events+0x153/0x1cc
[158645.539166] [<c14bd57b>] cfg80211_event_work+0x26/0x36
[158645.539195] [<c10482ae>] process_one_work+0x219/0x38b
[158645.539273] [<c14bd555>] ? wiphy_new+0x419/0x419
[158645.539301] [<c10486cb>] worker_thread+0xf6/0x1bf
[158645.539379] [<c10485d5>] ? rescuer_thread+0x1b5/0x1b5
[158645.539407] [<c104b3e2>] kthread+0x62/0x67
[158645.539484] [<c104b380>] ? __init_kthread_worker+0x42/0x42
[158645.539514] [<c151309a>] kernel_thread_helper+0x6/0xd
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses the "tcp.limit_in_bytes" field of the kmem_cgroup to
effectively control the amount of kernel memory pinned by a cgroup.
This value is ignored in the root cgroup, and in all others,
caps the value specified by the admin in the net namespaces'
view of tcp_sysctl_mem.
If namespaces are being used, the admin is allowed to set a
value bigger than cgroup's maximum, the same way it is allowed
to set pretty much unlimited values in a real box.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com>
CC: David S. Miller <davem@davemloft.net>
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows each namespace to independently set up
its levels for tcp memory pressure thresholds. This patch
alone does not buy much: we need to make this values
per group of process somehow. This is achieved in the
patches that follows in this patchset.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
CC: David S. Miller <davem@davemloft.net>
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces memory pressure controls for the tcp
protocol. It uses the generic socket memory pressure code
introduced in earlier patches, and fills in the
necessary data in cg_proto struct.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtisu.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this work is to move the memory pressure tcp
controls to a cgroup, instead of just relying on global
conditions.
To avoid excessive overhead in the network fast paths,
the code that accounts allocated memory to a cgroup is
hidden inside a static_branch(). This branch is patched out
until the first non-root cgroup is created. So when nobody
is using cgroups, even if it is mounted, no significant performance
penalty should be seen.
This patch handles the generic part of the code, and has nothing
tcp-specific.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtsu.com>
CC: Kirill A. Shutemov <kirill@shutemov.name>
CC: David S. Miller <davem@davemloft.net>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all uses of struct sock fields' memory_pressure,
memory_allocated, sockets_allocated, and sysctl_mem to acessor
macros. Those macros can either receive a socket argument, or a mem_cgroup
argument, depending on the context they live in.
Since we're only doing a macro wrapping here, no performance impact at all is
expected in the case where we don't have cgroups disabled.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com>
CC: David S. Miller <davem@davemloft.net>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of testing defined(CONFIG_IPV6) || defined(CONFIG_IPV6_MODULE)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP diag get_exact handler will require them to find a
socket by provided net, [sd]addr-s, [sd]ports and device.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now RED uses a Q0.32 number to store max_p (max probability), allow
RED/GRED/CHOKE to use/report full resolution at config/dump time.
Old tc binaries are non aware of new attributes, and still set/get Plog.
New tc binary set/get both Plog and max_p for backward compatibility,
they display "probability value" if they get max_p from new kernels.
# tc -d qdisc show dev ...
...
qdisc red 10: parent 1:1 limit 360Kb min 30Kb max 90Kb ecn ewma 5
probability 0.09 Scell_log 15
Make sure we avoid potential divides by 0 in reciprocal_value(), if
(max_th - min_th) is big.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adaptative RED AQM for linux, based on paper from Sally FLoyd,
Ramakrishna Gummadi, and Scott Shenker, August 2001 :
http://icir.org/floyd/papers/adaptiveRed.pdf
Goal of Adaptative RED is to make max_p a dynamic value between 1% and
50% to reach the target average queue : (max_th - min_th) / 2
Every 500 ms:
if (avg > target and max_p <= 0.5)
increase max_p : max_p += alpha;
else if (avg < target and max_p >= 0.01)
decrease max_p : max_p *= beta;
target :[min_th + 0.4*(min_th - max_th),
min_th + 0.6*(min_th - max_th)].
alpha : min(0.01, max_p / 4)
beta : 0.9
max_P is a Q0.32 fixed point number (unsigned, with 32 bits mantissa)
Changes against our RED implementation are :
max_p is no longer a negative power of two (1/(2^Plog)), but a Q0.32
fixed point number, to allow full range described in Adatative paper.
To deliver a random number, we now use a reciprocal divide (thats really
a multiply), but this operation is done once per marked/droped packet
when in RED_BETWEEN_TRESH window, so added cost (compared to previous
AND operation) is near zero.
dump operation gives current max_p value in a new TCA_RED_MAX_P
attribute.
Example on a 10Mbit link :
tc qdisc add dev $DEV parent 1:1 handle 10: est 1sec 8sec red \
limit 400000 min 30000 max 90000 avpkt 1000 \
burst 55 ecn adaptative bandwidth 10Mbit
# tc -s -d qdisc show dev eth3
...
qdisc red 10: parent 1:1 limit 400000b min 30000b max 90000b ecn
adaptative ewma 5 max_p=0.113335 Scell_log 15
Sent 50414282 bytes 34504 pkt (dropped 35, overlimits 1392 requeues 0)
rate 9749Kbit 831pps backlog 72056b 16p requeues 0
marked 1357 early 35 pdrop 0 other 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare cfg80211 for IBSS HT:
* extend cfg80211 ibss struct with channel_type
* Check if extension channel can be used
* Export can_beacon_sec_chan for use in mac80211 (will be called
from ibss.c later).
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
[siwu@hrz.tu-chemnitz.de: Updates]
* fix cfg80211_can_beacon_ext_chan comment
* remove implicit channel_type enum assumptions
* remove radar channel flags check
* add HT IBSS feature flag
* reword commit message
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix dump upon device removal, by moving deinitialization from
platform-device-remove to network-interface-uninit.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reflect the fact that a refrence is not obtained to the
resulting neighbour entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Roland Dreier <roland@purestorage.com>
like rt6_lookup, but allows caller to pass in flowi6 structure.
Will be used by the upcoming ipv6 netfilter reverse path filter
match.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It's only used in net/ipv6/route.c and the NULL device check is
superfluous for all of the existing call sites.
Just expand the __ndisc_lookup_errno() call at each location.
Signed-off-by: David S. Miller <davem@davemloft.net>
While parsing through IPv6 extension headers, fragment headers are
skipped making them invisible to the caller. This reports the
fragment offset of the last header in order to make it possible to
determine whether the packet is fragmented and, if so whether it is
a first or last fragment.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Open vSwitch uses Generic Netlink interface for communication
between userspace and kernel module. genl_notify() is used
for sending notification back to userspace.
genl_notify() is analogous to rtnl_notify() but uses genl_sock
instead of rtnl.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Use bluetooth names instead of BT SIG assigned numbers
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The below patch fixes some typos in various parts of the kernel, as well as fixes some comments.
Please let me know if I missed anything, and I will try to get it changed and resent.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds the parameter struct and the command complete event
handler to the LE Set Scan Parameter HCI command.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds the dev_flags field to struct hci_dev. This new
flags variable should be used to define flags related to BR/EDR
and/or LE controller itself. It should be used to define flags
which represents states from the controller. The dev_flags is
cleared in case the controller sends a Reset Command Complete
Event to the host.
Also, this patch adds the HCI_LE_SCAN flag which was created to
track if the controller is performing LE scan or not. The flag
is set/cleared when the controller starts/stops scanning.
This is an initial effort to stop using hdev->flags to define
internal flags since it is exported to userspace by an ioctl.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Upstream Code Aurora function with minor trivial fixes.
Origin: git://codeaurora.org/kernel/msm.git
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
gcc compiler is smart enough to use a single load/store if we
memcpy(dptr, sptr, 8) on x86_64, regardless of
CONFIG_CC_OPTIMIZE_FOR_SIZE
In IP header, daddr immediately follows saddr, this wont change in the
future. We only need to make sure our flowi4 (saddr,daddr) fields wont
break the rule.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include linux/if_ether.h to fix below build errors:
CC arch/arm/mach-kirkwood/common.o
In file included from arch/arm/mach-kirkwood/common.c:19:
include/net/dsa.h: In function 'dsa_uses_dsa_tags':
include/net/dsa.h:192: error: 'ETH_P_DSA' undeclared (first use in this function)
include/net/dsa.h:192: error: (Each undeclared identifier is reported only once
include/net/dsa.h:192: error: for each function it appears in.)
include/net/dsa.h: In function 'dsa_uses_trailer_tags':
include/net/dsa.h:197: error: 'ETH_P_TRAILER' undeclared (first use in this function)
make[1]: *** [arch/arm/mach-kirkwood/common.o] Error 1
make: *** [arch/arm/mach-kirkwood] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some MITM protection pairing scenarios, the user is
required to enter or accept a 6 digit passkey.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Remove unused enum cfcnfg_phy_type and the parameter to cfserl_create.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enrolling CAIF link layers are refactored.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit a4a710c4a7 (pkt_sched: Change PSCHED_SHIFT from 10 to
6) it seems RED/GRED are broken.
red_calc_qavg_from_idle_time() computes a delay in us units, but this
delay is now 16 times bigger than real delay, so the final qavg result
smaller than expected.
Use standard kernel time services since there is no need to obfuscate
them.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of instantiating an entire new neigh_table instance
just for ATM handling, use the neigh device private facility.
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to alloc for device specific private areas for
neighbour entries, and in order to do that we have to move
away from the fixed allocation size enforced by using
neigh_table->kmem_cachep
As a nice side effect we can now use kfree_rcu().
Signed-off-by: David S. Miller <davem@davemloft.net>
Tons of drivers missed that we use mBm and not dBm...
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Le lundi 28 novembre 2011 à 19:06 -0500, David Miller a écrit :
> From: Dimitris Michailidis <dm@chelsio.com>
> Date: Mon, 28 Nov 2011 08:25:39 -0800
>
> >> +bool skb_flow_dissect(const struct sk_buff *skb, struct flow_keys
> >> *flow)
> >> +{
> >> + int poff, nhoff = skb_network_offset(skb);
> >> + u8 ip_proto;
> >> + u16 proto = skb->protocol;
> >
> > __be16 instead of u16 for proto?
>
> I'll take care of this when I apply these patches.
( CC trimmed )
Thanks David !
Here is a small patch to use one 64bit load/store on x86_64 instead of
two 32bit load/stores.
[PATCH net-next] flow_dissector: use a 64bit load/store
gcc compiler is smart enough to use a single load/store if we
memcpy(dptr, sptr, 8) on x86_64, regardless of
CONFIG_CC_OPTIMIZE_FOR_SIZE
In IP header, daddr immediately follows saddr, this wont change in the
future. We only need to make sure our flow_keys (src,dst) fields wont
break the rule.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 2005 (c1b4a7e695)
tcp_tso_should_defer has been using tcp_max_burst() as a target limit
for deciding how large to make outgoing TSO packets when not using
sysctl_tcp_tso_win_divisor. But since 2008
(dd9e0dda66) tcp_max_burst() returns the
reordering degree. We should not have tcp_tso_should_defer attempt to
build larger segments just because there is more reordering. This
commit splits the notion of deferral size used in TSO from the notion
of burst size used in cwnd moderation, and returns the TSO deferral
limit to its original value.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any headers included by drivers should be under include/, and
any definitions they use are not really private to the core as
the name "dsa_priv.h" suggests.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use at least two flow dissectors in network stack, with known
limitations and code duplication.
Introduce skb_flow_dissect() to factorize this, highly inspired from
existing dissector from __skb_get_rxhash()
Note : We extensively use skb_header_pointer(), this permits us to not
touch skb at all.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 802.11mb 13.9.11.3
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the configuration changes in nl80211/cfg80211.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now inetpeer is the place where we cache redirect information for ipv4
destinations, we must be able to invalidate informations when a route is
added/removed on host.
As inetpeer is not yet namespace aware, this patch adds a shared
redirect_genid, and a per inetpeer redirect_genid. This might be changed
later if inetpeer becomes ns aware.
Cache information for one inerpeer is valid as long as its
redirect_genid has the same value than global redirect_genid.
Reported-by: Arkadiusz Miśkiewicz <a.miskiewicz@gmail.com>
Tested-by: Arkadiusz Miśkiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eth_type_trans() will use these functions if DSA is enabled, which
blocks building DSA as a module.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move all mtu handling from dst_mtu() down to the protocol
layer. So each protocol can implement the mtu handling in
a different manner.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We plan to invoke the dst_opt->default_mtu() method unconditioally
from dst_mtu(). So rename the method to dst_opt->mtu() to match
the name with the new meaning.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can not update iph->daddr in ip_options_rcv_srr(), It is too early.
When some exception ocurred later (eg. in ip_forward() when goto
sr_failed) we need the ip header be identical to the original one as
ICMP need it.
Add a field 'nexthop' in struct ip_options to save nexthop of LSRR
or SSRR option.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I broke the build with the addition of netprio_cgroups if CONFIG_CGROUPS=n.
This patch corrects it by moving the offending struct into an ifdef
CONFIG_CGROUPS block. Also clean up a few needless defines and inline functions
that don't get called if CONFIG_CGROUPS isn't defined while Im at it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
C assignment can handle struct in6_addr copying.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current addr_match() is errh, under-optimized.
Compiler doesn't know that memcmp() branch doesn't trigger for IPv4.
Also, pass addresses by value -- they fit into register.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds in the infrastructure code to create the network priority
cgroup. The cgroup, in addition to the standard processes file creates two
control files:
1) prioidx - This is a read-only file that exports the index of this cgroup.
This is a value that is both arbitrary and unique to a cgroup in this subsystem,
and is used to index the per-device priority map
2) priomap - This is a writeable file. On read it reports a table of 2-tuples
<name:priority> where name is the name of a network interface and priority is
indicates the priority assigned to frames egresessing on the named interface and
originating from a pid in this cgroup
This cgroup allows for skb priority to be set prior to a root qdisc getting
selected. This is benenficial for DCB enabled systems, in that it allows for any
application to use dcb configured priorities so without application modification
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
CC: Robert Love <robert.w.love@intel.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an oops that can be triggered following this recipe:
0) make sure nf_conntrack_netlink and nf_conntrack_ipv4 are loaded.
1) container is started.
2) connect to it via lxc-console.
3) generate some traffic with the container to create some conntrack
entries in its table.
4) stop the container: you hit one oops because the conntrack table
cleanup tries to report the destroy event to user-space but the
per-netns nfnetlink socket has already gone (as the nfnetlink
socket is per-netns but event callback registration is global).
To fix this situation, we make the ctnl_notifier per-netns so the
callback is registered/unregistered if the container is
created/destroyed.
Alex Bligh and Alexey Dobriyan originally proposed one small patch to
check if the nfnetlink socket is gone in nfnetlink_has_listeners,
but this is a very visited path for events, thus, it may reduce
performance and it looks a bit hackish to check for the nfnetlink
socket only to workaround this situation. As a result, I decided
to follow the bigger path choice, which seems to look nicer to me.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Reported-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This allows users to disable features such as HT, HT40,
and to modify the MCS, AMPDU, and AMSDU settings for
drivers that support it.
The MCS, AMPDU, and AMSDU features that may be disabled are
are reported in the phy-info netlink message as a mask.
Attemping to disable features that are not supported will
take no affect, but will not return errors. This is to aid
backwards compatibility in user-space apps that may not be
clever enough to deal with parsing the the capabilities mask.
This patch only enables the infrastructure. An additional
patch will enable the feature in mac80211.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No other driver ever ended up using this, and
the commit forgot to move the prototype so no
driver could have used it. Revert it, if any
driver shows up and needs it it can be moved
again, but until then it's more efficient to
have it in mac80211 where the only user is.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 implements these for all devices,
but given restrictions of some devices that isn't
really true, so prepare for being able to remove the
capability for some mac80211 devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers can usually handle fragmented packets
much easier when they get the entire list of
fragments at once. The only thing they need to
do is keep enough space on the queues for up
to ten fragments of a single MSDU.
This allows them to implement this with a new
operation tx_frags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This grants drivers access to the DFS region that a
regulatory domain belongs to.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wireless-regdb now has support for mapping a country to
one DFS region. CRDA sends this to us now so process it
so we can provide that hint to drivers. This will later be
used by code for processing DFS in a way that meets the
criteria for the DFS region the country belongs to.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mgmt_start_discovery command contains the type of discovery that
should be started so this should be passed to the start_discovery
function. This patch doesn't yet add any action depending on the type of
the requested discovery.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The management protocol uses a single byte for error codes (aka command
status). In some places this value is directly copied from HCI and in
other a POSIX error number is used. This makes it impossible for
user-space to uniquily decipher the meaning of an error.
To solve this issue a new mgmt-specific set of error codes is added
along with a conversion table for HCI status values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The kernel needs to know whether it should connect to a device over
BR/EDR or over LE. This is particularly important in the future when
dual-mode device may be connectable also over LE. It is also important
if/when we decide to move the LE advertisement cache from the kernel
into user-space. Adding the type to the mgmt command also ensures
conformance with the latest mgmt API spec.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patches creates mgmt_stop_discovery_failed() which removes
pending MGMT_OP_STOP_DISCOVERY commands and sends proper command
status events.
This patch also fixes the MGMT_OP_STOP_DISCOVERY command leak in
case cancel inquiry fails.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch renames the function mgmt_inquiry_failed() to
mgmt_start_discovery_failed(). This function is more related
to MGMT_OP_START_DISCOVERY command handling than to inquiry.
Besides, this functions will be reused by LE based discovery
procedures in case of failure.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Le mercredi 09 novembre 2011 à 16:21 -0500, David Miller a écrit :
> From: David Miller <davem@davemloft.net>
> Date: Wed, 09 Nov 2011 16:16:44 -0500 (EST)
>
> > From: Eric Dumazet <eric.dumazet@gmail.com>
> > Date: Wed, 09 Nov 2011 12:14:09 +0100
> >
> >> unres_qlen is the number of frames we are able to queue per unresolved
> >> neighbour. Its default value (3) was never changed and is responsible
> >> for strange drops, especially if IP fragments are used, or multiple
> >> sessions start in parallel. Even a single tcp flow can hit this limit.
> > ...
> >
> > Ok, I've applied this, let's see what happens :-)
>
> Early answer, build fails.
>
> Please test build this patch with DECNET enabled and resubmit. The
> decnet neigh layer still refers to the removed ->queue_len member.
>
> Thanks.
Ouch, this was fixed on one machine yesterday, but not the other one I
used this morning, sorry.
[PATCH V5 net-next] neigh: new unresolved queue limits
unres_qlen is the number of frames we are able to queue per unresolved
neighbour. Its default value (3) was never changed and is responsible
for strange drops, especially if IP fragments are used, or multiple
sessions start in parallel. Even a single tcp flow can hit this limit.
$ arp -d 192.168.20.108 ; ping -c 2 -s 8000 192.168.20.108
PING 192.168.20.108 (192.168.20.108) 8000(8028) bytes of data.
8008 bytes from 192.168.20.108: icmp_seq=2 ttl=64 time=0.322 ms
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for frame fragmentation.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading /proc/net/snmp6 on a machine with a lot of cpus is very
expensive (can be ~88000 us).
This is because ICMPV6MSG MIB uses 4096 bytes per cpu, and folding
values for all possible cpus can read 16 Mbytes of memory (32MBytes on
non x86 arches)
ICMP messages are not considered as fast path on a typical server, and
eventually few cpus handle them anyway. We can afford an atomic
operation instead of using percpu data.
This saves 4096 bytes per cpu and per network namespace.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow setting a probe response template for an interface operating in
AP mode. Low level drivers are notified about changes in the probe
response template and are able to retrieve a copy of the current probe
response. This data can, for example, be uploaded to hardware as a
template.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass probe-response data from usermode via beacon parameters.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Notify user-space about probe-response offloading support in the driver.
A wiphy flag is used to indicate support and a bitmap of protocols
determines which protocols are supported.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The macro is only used in ipw2200 and we certainly
don't want to encourage its use, so move it out of
the radiotap header file and into the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check if NCI data flow control is used in nci_tx_work.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused NCI operations, e.g. create static rf connection.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Addition, deletion and modification of NCI constants.
Changes in NCI commands, responses and notifications structures.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just add API to get the channel & report it. Trivial really.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rename to l2cap_chan_check_security() to make it consistent with other
l2cap_exported functions. This function will be exported in a later
commit.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Since disconnecting may fail the status needs to be communicated to user
space. This also updates the implementation to match the latest mgmt API
specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Since the command can fail we need to have a proper response with the
remote address and a failure status for it. This also updates it to
conform to the latest mgmt API spec.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
It's necessary to know the distinction between public and random LE
addresses so the mgmt interface also needs to distinguish between them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Le lundi 07 novembre 2011 à 15:33 +0100, Eric Dumazet a écrit :
> At least, in recent kernels we dont change dst->refcnt in forwarding
> patch (usinf NOREF skb->dst)
>
> One particular point is the atomic_inc(dst->refcnt) we have to perform
> when queuing an UDP packet if socket asked PKTINFO stuff (for example a
> typical DNS server has to setup this option)
>
> I have one patch somewhere that stores the information in skb->cb[] and
> avoid the atomic_{inc|dec}(dst->refcnt).
>
OK I found it, I did some extra tests and believe its ready.
[PATCH net-next] ipv4: IP_PKTINFO doesnt need dst reference
When a socket uses IP_PKTINFO notifications, we currently force a dst
reference for each received skb. Reader has to access dst to get needed
information (rt_iif & rt_spec_dst) and must release dst reference.
We also forced a dst reference if skb was put in socket backlog, even
without IP_PKTINFO handling. This happens under stress/load.
We can instead store the needed information in skb->cb[], so that only
softirq handler really access dst, improving cache hit ratios.
This removes two atomic operations per packet, and false sharing as
well.
On a benchmark using a mono threaded receiver (doing only recvmsg()
calls), I can reach 720.000 pps instead of 570.000 pps.
IP_PKTINFO is typically used by DNS servers, and any multihomed aware
UDP application.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the socket wifi TX status error
queue reflection in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new wifi socket TX capability should be
supported by wifi drivers, let them advertise
whether they do or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For probe responses it can be useful to not wait for ACK to
avoid retransmissions if the station that sent the probe is
already on the next channel, so allow userspace to request
not caring about the ACK with a new nl80211 flag.
Since mac80211 needs to be updated for the new function
prototype anyway implement it right away -- it's just a
few lines of code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The frames are used by AP/STA WDS mode, and hostapd
needs to know when such a frame was received to set
up the VLAN appropriately to allow using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to register to received beacon frames
to allow implementing OLBC logic in userspace. The
registration is per wiphy since there's no point in
receiving the same frame multiple times.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the AP SME in hostapd is used it wants to
probe the clients when they have been idle for
some time. Add explicit API to support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to advertise that the device
contains the AP SME and what features it can
support. There are currently no features in
the bitmap -- probe response offload will be
advertised by a few patches Arik is working
on now (who took over from Guy Eilam) and a
device with AP SME will typically implement
and require response offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To implement AP mode without monitor interfaces we
need to be able to send a deauth to stations that
send frames without being associated. Enable this
by adding a new nl80211 event for such frames that
an application can subscribe to.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that need to drop a frame before it
can be transmitted will usually simply free
that frame. This is currently fine, but in
the future it'll be needed to tell mac80211
about this case, so add a new routine that
frees a TX skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reading /proc/net/snmp on a machine with a lot of cpus is very expensive
(can be ~88000 us).
This is because ICMPMSG MIB uses 4096 bytes per cpu, and folding values
for all possible cpus can read 16 Mbytes of memory.
ICMP messages are not considered as fast path on a typical server, and
eventually few cpus handle them anyway. We can afford an atomic
operation instead of using percpu data.
This saves 4096 bytes per cpu and per network namespace.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.1X EAPOL handshake hostapd does requires
knowing whether the frame was ack'ed by the peer.
Currently, we fudge this pretty badly by not even
transmitting the frame as a normal data frame but
injecting it with radiotap and getting the status
out of radiotap monitor as well. This is rather
complex, confuses users (mon.wlan0 presence) and
doesn't work with all hardware.
To get rid of that hack, introduce a real wifi TX
status option for data frame transmissions.
This works similar to the existing TX timestamping
in that it reflects the SKB back to the socket's
error queue with a SCM_WIFI_STATUS cmsg that has
an int indicating ACK status (0/1).
Since it is possible that at some point we will
want to have TX timestamping and wifi status in a
single errqueue SKB (there's little point in not
doing that), redefine SO_EE_ORIGIN_TIMESTAMPING
to SO_EE_ORIGIN_TXSTATUS which can collect more
than just the timestamp; keep the old constant
as an alias of course. Currently the internal APIs
don't make that possible, but it wouldn't be hard
to split them up in a way that makes it possible.
Thanks to Neil Horman for helping me figure out
the functions that add the control messages.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function returns a referenced BSS struct
(or NULL), annotate with __must_check. It seems
that a lot of drivers get this completely wrong
and leak all BSS structs as a result.
Reported-by: Adam Mikuta <Adam.Mikuta@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the pending management command list (previously global
to mgmt.c) into struct hci_dev. This makes it possible to do proper
locking when accessing it (through the existing hci_dev locks) and
thereby avoid race conditions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The current global pending command list in mgmt.c is racy. Possibly the
simplest way to fix it is to have per-hci dev lists instead of a global
one (all commands that need a pending struct are hci_dev specific).
This way the list can be protected using the already existing per-hci
dev lock. To enable this refactoring the first thing that needs to be
done is to ensure that the mgmt functions have access to the hci_dev
struct (instead of just the dev id).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Make clear that sk_clone() and inet_csk_clone() return a locked socket.
Add _lock() prefix and kerneldoc.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some cards can generate CCMP IVs in HW, but require the space for the IV
to be pre-allocated in the frame at the correct offset. Add a key flag
that allows us to achieve this.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast retransmission after changing the last address
with ASCONF negotiation
Signed-off-by: Michio Honda <micchie@sfc.wide.ad.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new struct members were not documented, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds address type info (typically BR/EDR vs LE) to management
messages that need this. This also ensures conformance to the latest
management API specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
BR/EDR link keys have their own commands and events (separate from SMP)
and the remove_keys command (previously remove_key) removes keys of any
kind for the specified remote address.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The power off code doesn't need to use its own custom timer since the
delayed_work API provides the exact same functionality.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
A proper mgmt_command_status should be returned to user-space if either
discoverable or connectable enabling fails.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Based on the revised mgmt API set_discoverable has a timeout parameter
to specify how long the adapter will remain discoverable. A value of 0
means "indefinitively".
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a function to hci_core to cancel an ongoing inquiry.
According to the Bluetooth spec, the inquiry cancel command should
only be issued after the inquiry command has been issued, a command
status event has been received for the inquiry command, and before
the inquiry complete event occurs.
As HCI_INQUIRY flag is only set just after an inquiry command status
event occurs and it is cleared just after an inquiry complete event
occurs, the inquiry cancel command should be issued only if HCI_INQUIRY
flag is set.
Additionally, cancel inquiry related code from stop_discovery() were
replaced by a hci_cancel_inquiry() call.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a function to hci_core to carry out inquiry.
All inquiry code from start_discovery() were replaced by a
hci_do_inquiry() call.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Symbolic fixed channel IDs will be used instead of magic numbers.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
AMP channel creation and channel moves are coordinated using the L2CAP
signaling channel. These definitions cover the "create channel",
"move channel", and "move channel confirm" signals.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Each channel has a policy to require BR/EDR (the default),
prefer BR/EDR, or prefer AMP.
Check for valid policy value and L2CAP mode.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This variable is currently only accessible within l2cap_core.c, but
it is also needed in l2cap_sock.c
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Allow control of AMP functionality on L2CAP sockets. By default,
connections will be restricted to BR/EDR. Manipulating the
BT_CHANNEL_POLICY option allows for channels to be moved to or created
on AMP controllers.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This implement priority based scheduler using skbuffer priority set via
SO_PRIORITY socket option.
It introduces hci_chan_hash (list of HCI Channel/hci_chan) per connection,
each item in this list refer to a L2CAP connection and it is used to
queue the data for transmission.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This was triggered by turning off encryption on ACL link when rfcomm
was using high security. rfcomm_security_cfm (which is called from rx
task) was closing DLC and this involves sending disconnect message
(and locking socket).
Move closing DLC to rfcomm_process_dlcs and only flag DLC for closure
in rfcomm_security_cfm.
BUG: sleeping function called from invalid context at net/core/sock.c:2032
in_atomic(): 1, irqs_disabled(): 0, pid: 1788, name: kworker/0:3
[<c0068a08>] (unwind_backtrace+0x0/0x108) from [<c05e25dc>] (dump_stack+0x20/0x24)
[<c05e25dc>] (dump_stack+0x20/0x24) from [<c0087ba8>] (__might_sleep+0x110/0x12c)
[<c0087ba8>] (__might_sleep+0x110/0x12c) from [<c04801d8>] (lock_sock_nested+0x2c/0x64)
[<c04801d8>] (lock_sock_nested+0x2c/0x64) from [<c05670c8>] (l2cap_sock_sendmsg+0x58/0xcc)
[<c05670c8>] (l2cap_sock_sendmsg+0x58/0xcc) from [<c047cf6c>] (sock_sendmsg+0xb0/0xd0)
[<c047cf6c>] (sock_sendmsg+0xb0/0xd0) from [<c047cfc8>] (kernel_sendmsg+0x3c/0x44)
[<c047cfc8>] (kernel_sendmsg+0x3c/0x44) from [<c056b0e8>] (rfcomm_send_frame+0x50/0x58)
[<c056b0e8>] (rfcomm_send_frame+0x50/0x58) from [<c056b168>] (rfcomm_send_disc+0x78/0x80)
[<c056b168>] (rfcomm_send_disc+0x78/0x80) from [<c056b9f4>] (__rfcomm_dlc_close+0x2d0/0x2fc)
[<c056b9f4>] (__rfcomm_dlc_close+0x2d0/0x2fc) from [<c056bbac>] (rfcomm_security_cfm+0x140/0x1e0)
[<c056bbac>] (rfcomm_security_cfm+0x140/0x1e0) from [<c0555ec0>] (hci_event_packet+0x1ce8/0x4d84)
[<c0555ec0>] (hci_event_packet+0x1ce8/0x4d84) from [<c0550380>] (hci_rx_task+0x1d0/0x2d0)
[<c0550380>] (hci_rx_task+0x1d0/0x2d0) from [<c009ee04>] (tasklet_action+0x138/0x1e4)
[<c009ee04>] (tasklet_action+0x138/0x1e4) from [<c009f21c>] (__do_softirq+0xcc/0x274)
[<c009f21c>] (__do_softirq+0xcc/0x274) from [<c009f6c0>] (do_softirq+0x60/0x6c)
[<c009f6c0>] (do_softirq+0x60/0x6c) from [<c009f794>] (local_bh_enable_ip+0xc8/0xd4)
[<c009f794>] (local_bh_enable_ip+0xc8/0xd4) from [<c05e5804>] (_raw_spin_unlock_bh+0x48/0x4c)
[<c05e5804>] (_raw_spin_unlock_bh+0x48/0x4c) from [<c040d470>] (data_from_chip+0xf4/0xaec)
[<c040d470>] (data_from_chip+0xf4/0xaec) from [<c04136c0>] (send_skb_to_core+0x40/0x178)
[<c04136c0>] (send_skb_to_core+0x40/0x178) from [<c04139f4>] (cg2900_hu_receive+0x15c/0x2d0)
[<c04139f4>] (cg2900_hu_receive+0x15c/0x2d0) from [<c0414cb8>] (hci_uart_tty_receive+0x74/0xa0)
[<c0414cb8>] (hci_uart_tty_receive+0x74/0xa0) from [<c02cbd9c>] (flush_to_ldisc+0x188/0x198)
[<c02cbd9c>] (flush_to_ldisc+0x188/0x198) from [<c00b2774>] (process_one_work+0x144/0x4b8)
[<c00b2774>] (process_one_work+0x144/0x4b8) from [<c00b2e8c>] (worker_thread+0x198/0x468)
[<c00b2e8c>] (worker_thread+0x198/0x468) from [<c00b9bc8>] (kthread+0x98/0xa0)
[<c00b9bc8>] (kthread+0x98/0xa0) from [<c0061744>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds the necessary code to send proper command status or
command complete events to the start/stop discovery management commands.
Before this patch these events were completely missing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This uses SO_PRIORITY to set the skbuffer priority field
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
hci_unregister_dev cannot fail and always returns 0. The drivers already ignore
the return value so we can safely make it return void.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Timers set by __set_chan_timer() should use miliseconds instead of
jiffies. Commit 942ecc9c46 updated
l2cap_set_timer() so it expects timeout to be specified in msecs
instead of jiffies. This makes timeouts unreliable when CONFIG_HZ
is not set to 1000.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
forcedeth: fix a few sparse warnings (variable shadowing)
forcedeth: Improve stats counters
forcedeth: remove unneeded stats updates
forcedeth: Acknowledge only interrupts that are being processed
forcedeth: fix race when unloading module
MAINTAINERS/rds: update maintainer
wanrouter: Remove kernel_lock annotations
usbnet: fix oops in usbnet_start_xmit
ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
etherh: Add MAINTAINERS entry for etherh
bonding: comparing a u8 with -1 is always false
sky2: fix regression on Yukon Optima
netlink: clarify attribute length check documentation
netlink: validate NLA_MSECS length
i825xx:xscale:8390:freescale: Fix Kconfig dependancies
macvlan: receive multicast with local address
tg3: Update version to 3.121
tg3: Eliminate timer race with reset_task
tg3: Schedule at most one tg3_reset_task run
tg3: Obtain PCI function number from device
...
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
The documentation for how the length of attributes
is checked is wrong ("Exact length" isn't true, the
policy checks are for "minimum length") and a bit
misleading. Make it more complete and explain what
really happens.
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The warning really shouldn't happen, but until we
find the reason why it does don't spew it all the
time, just once is enough to know we've hit it.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the tcp and udp code creates a set of struct file_operations at runtime
while it can also be done at compile time, with the added benefit of then
having these file operations be const.
the trickiest part was to get the "THIS_MODULE" reference right; the naive
method of declaring a struct in the place of registration would not work
for this reason.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to address the following error during the compilation:
In file included from kernel/sysctl_binary.c:6:
include/net/ip_vs.h:1406: error: expected identifier or ‘(’ before ‘{’ token
make[1]: *** [kernel/sysctl_binary.o] Error 1
make[1]: *** Waiting for unfinished jobs....
That manifests itself when CONFIG_IP_VS_NFCT is undefined in .config file.
Signed-off-by: Krzysztof Wilczynski <krzysztof.wilczynski@linux.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
This patch exports several definitions that used to live under
include/net/netfilter/nf_nat.h. These definitions, although not
exported, have been used by iptables and other userspace
applications like miniupnpd since long time. Basically, these
userspace tools included some internal definition of the required
structures and they assume no changes in the binary representation
(which is OK indeed).
To resolve this situation, this patch makes public the required
structure and install them in INSTALL_HDR_PATH.
See: https://bugs.gentoo.org/376873, for more information.
This patch is heavily based on the initial patch sent by:
Anthony G. Basile <blueness@gentoo.org>
Which was entitled:
netfilter: export sanitized nf_nat.h to INSTALL_HDR_PATH
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
These two small inlines make calls to try_module_get() and
module_put() which would force us to keep module.h present
within yet another common include header. We can avoid this
by turning them into macros. The hci_dev_hold construct
is patterned off of raw_spin_trylock_irqsave() in spinlock.h
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This file was using the module get/put functions in two simple inline
functions. But module_get/put were only within scope because of
the implicit presence of module.h being everywhere.
Rather than add module.h to another file in include/ -- which is
exactly the thing we are trying to avoid, simply convert these
one-line functions into a define, as per what was done for the
device_schedule_callback() in commit 523ded71de.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The implicit presence of module.h everywhere meant that this header
also was getting moduleparam.h which defines struct kernel_param.
Since it only needs to know that kernel_param is a struct, call that
out instead of adding an include of moduleparam.h -- to get rid of this:
include/net/netfilter/nf_conntrack.h:316: warning: 'struct kernel_param' declared inside parameter list
include/net/netfilter/nf_conntrack.h:316: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The <linux/module.h> pretty much brings in the kitchen sink along
with it, so it should be avoided wherever reasonably possible in
terms of being included from other commonly used <linux/something.h>
files, as it results in a measureable increase on compile times.
The worst culprit was probably device.h since it is used everywhere.
This file also had an implicit dependency/usage of mutex.h which was
masked by module.h, and is also fixed here at the same time.
There are over a dozen other headers that simply declare the
struct instead of pulling in the whole file, so follow their lead
and simply make it a few more.
Most of the implicit dependencies on module.h being present by
these headers pulling it in have been now weeded out, so we can
finally make this change with hopefully minimal breakage.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This file has modular references, but they are limited to
those which are covered by the simple "struct module;"
declaration used in dozens of other places. In fact that
declaration is already there (just outside of the context
of this commit) so simply remove the include line.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There is nothing module specific in this header, and removing
it doesn't seem to uncover any implicit dependencies either.
Must be simply a vestige of an ancient legacy.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
commit 66b13d99d9 (ipv4: tcp: fix TOS value in ACK messages sent from
TIME_WAIT) fixed IPv4 only.
This part is for the IPv6 side, adding a tclass param to ip6_xmit()
We alias tw_tclass and tw_tos, if socket family is INET6.
[ if sockets is ipv4-mapped, only IP_TOS socket option is used to fill
TOS field, TCLASS is not taken into account ]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://github.com/ericvh/linux:
9p: fix 9p.txt to advertise msize instead of maxdata
net/9p: Convert net/9p protocol dumps to tracepoints
fs/9p: change an int to unsigned int
fs/9p: Cleanup option parsing in 9p
9p: move dereference after NULL check
fs/9p: inode file operation is properly initialized init_special_inode
fs/9p: Update zero-copy implementation in 9p
It was enabled by default and the messages guarded
by the define are useful.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this msize=4294967295 will result in a crash
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
* remove lot of update to different data structure
* add a seperate callback for zero copy request.
* above makes non zero copy code path simpler
* remove conditionalizing TREAD/TREADDIR/TWRITE in the zero copy path
* Fix the dotu p9_check_errors with zero copy. Add sufficient doc around
* Add support for both in and output buffers in zero copy callback
* pin and unpin pages in the same context
* use helpers instead of defining page offset and rest of page ourself
* Fix mem leak in p9_check_errors
* Remove 'E' and 'F' in p9pdu_vwritef
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
There is a long standing bug in linux tcp stack, about ACK messages sent
on behalf of TIME_WAIT sockets.
In the IP header of the ACK message, we choose to reflect TOS field of
incoming message, and this might break some setups.
Example of things that were broken :
- Routing using TOS as a selector
- Firewalls
- Trafic classification / shaping
We now remember in timewait structure the inet tos field and use it in
ACK generation, and route lookup.
Notes :
- We still reflect incoming TOS in RST messages.
- We could extend MuraliRaja Muniraju patch to report TOS value in
netlink messages for TIME_WAIT sockets.
- A patch is needed for IPv6
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now tcp_md5_hash_header() has a const tcphdr argument, we can add more
const attributes to callers.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_md5_hash_header() writes into skb header a temporary zero value,
this might confuse other users of this area.
Since tcphdr is small (20 bytes), copy it in a temporary variable and
make the change in the copy.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
INET_ECN_encapsulate() is better understood if we can read the official
statement.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding const qualifiers to pointers can ease code review, and spot some
bugs. It might allow compiler to optimize code further.
For example, is it legal to temporary write a null cksum into tcphdr
in tcp_md5_hash_header() ? I am afraid a sniffer could catch the
temporary null value...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added recovery check of CA wake status in case of wake up timeout.
Added check of CA wake status in case of wake down timeout.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added sanity check for length of CAIF frames, and tear down of
CAIF link-layer device upon protocol error.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAIF HSI uses a timer for inactivity. Upon timeout HSI-wake signaling
is initiated to allow power-down of the HSI block.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some platforms do not allow to put HSI block into low-power
mode when FIFO is not empty. The patch flushes (by reading)
FIFO at wake down sequence. Asynchronous read and write is
implemented for that. As a side effect this will also greatly
improve performance.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fragmented multicast frames are delivered to a single macvlan port,
because ip defrag logic considers other samples are redundant.
Implement a defrag step before trying to send the multicast frame.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 903ab86d19 of 1 March this year ("udp: Add
lockless transmit path") introduced a new fast TX path that broke the checksum
coverage computation of UDP-lite, which so far depended on up->len (only set
if the socket is locked and 0 in the fast path).
Fixed by providing both fast- and slow-path computation of checksum coverage.
The latter can be removed when UDP(-lite)v6 also uses a lockless transmit path.
Reported-by: Thomas Volkert <thomas@homer-conferencing.com>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for extended sequence numbers found in
extended control fields.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
There are three different Control Field formats: the Standard Control
Field, the Enhanced Control Field, and the Extended Control Field.
Patch adds function to handle all those fields seamlessly.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Partially revert 34918cd7. struct mgmt_key_info needs to have the same
size as its version exported to userspace.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reuse the already existing struct nl80211_sta_flag_update to specify
both, a flag mask and the flag set itself. This means
nl80211_sta_flag_update is now used for setting station flags and also
for getting station flags.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 already filled in the MCS rate info for rx'ed frames but tx'ed
frames that are sent to a monitor interface during the status callback
lack this information.
Add the radiotap fields for MCS info to ieee80211_tx_status_rtap_hdr
and populate them when sending tx'ed frames to the monitors.
The needed headroom is only extended by one byte since we don't include
legacy rate information in the rtap header for HT frames.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As we introduced hci_init_sysfs() we should also rename
hci_register_sysfs() and hci_unregister_sysfs() to hci_add_sysfs() and
hci_del_sysfs() like we do with hci_conn_add/del_sysfs(). It looks more
consistent now.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We must not call device_del() if we didn't use device_add(). See module.c
for comments on that. Therefore, we need to call device_initialize() when
allocating the hci device and later device_add() instead of
device_register().
This also fixes a bug when hci_register_dev() failed and we call
hci_free_dev() without a valid core device. hci_free_dev() segfaults while
calling put_device() on invalid memory.
We already do this with hci_conn connections (hci_conn_init_sysfs()) so
they do not need to be fixed.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This was triggered by turning off encryption on ACL link when rfcomm
was using high security. rfcomm_security_cfm (which is called from rx
task) was closing DLC and this involves sending disconnect message
(and locking socket).
Move closing DLC to rfcomm_process_dlcs and only flag DLC for closure
in rfcomm_security_cfm.
BUG: sleeping function called from invalid context at net/core/sock.c:2032
in_atomic(): 1, irqs_disabled(): 0, pid: 1788, name: kworker/0:3
[<c0068a08>] (unwind_backtrace+0x0/0x108) from [<c05e25dc>] (dump_stack+0x20/0x24)
[<c05e25dc>] (dump_stack+0x20/0x24) from [<c0087ba8>] (__might_sleep+0x110/0x12c)
[<c0087ba8>] (__might_sleep+0x110/0x12c) from [<c04801d8>] (lock_sock_nested+0x2c/0x64)
[<c04801d8>] (lock_sock_nested+0x2c/0x64) from [<c05670c8>] (l2cap_sock_sendmsg+0x58/0xcc)
[<c05670c8>] (l2cap_sock_sendmsg+0x58/0xcc) from [<c047cf6c>] (sock_sendmsg+0xb0/0xd0)
[<c047cf6c>] (sock_sendmsg+0xb0/0xd0) from [<c047cfc8>] (kernel_sendmsg+0x3c/0x44)
[<c047cfc8>] (kernel_sendmsg+0x3c/0x44) from [<c056b0e8>] (rfcomm_send_frame+0x50/0x58)
[<c056b0e8>] (rfcomm_send_frame+0x50/0x58) from [<c056b168>] (rfcomm_send_disc+0x78/0x80)
[<c056b168>] (rfcomm_send_disc+0x78/0x80) from [<c056b9f4>] (__rfcomm_dlc_close+0x2d0/0x2fc)
[<c056b9f4>] (__rfcomm_dlc_close+0x2d0/0x2fc) from [<c056bbac>] (rfcomm_security_cfm+0x140/0x1e0)
[<c056bbac>] (rfcomm_security_cfm+0x140/0x1e0) from [<c0555ec0>] (hci_event_packet+0x1ce8/0x4d84)
[<c0555ec0>] (hci_event_packet+0x1ce8/0x4d84) from [<c0550380>] (hci_rx_task+0x1d0/0x2d0)
[<c0550380>] (hci_rx_task+0x1d0/0x2d0) from [<c009ee04>] (tasklet_action+0x138/0x1e4)
[<c009ee04>] (tasklet_action+0x138/0x1e4) from [<c009f21c>] (__do_softirq+0xcc/0x274)
[<c009f21c>] (__do_softirq+0xcc/0x274) from [<c009f6c0>] (do_softirq+0x60/0x6c)
[<c009f6c0>] (do_softirq+0x60/0x6c) from [<c009f794>] (local_bh_enable_ip+0xc8/0xd4)
[<c009f794>] (local_bh_enable_ip+0xc8/0xd4) from [<c05e5804>] (_raw_spin_unlock_bh+0x48/0x4c)
[<c05e5804>] (_raw_spin_unlock_bh+0x48/0x4c) from [<c040d470>] (data_from_chip+0xf4/0xaec)
[<c040d470>] (data_from_chip+0xf4/0xaec) from [<c04136c0>] (send_skb_to_core+0x40/0x178)
[<c04136c0>] (send_skb_to_core+0x40/0x178) from [<c04139f4>] (cg2900_hu_receive+0x15c/0x2d0)
[<c04139f4>] (cg2900_hu_receive+0x15c/0x2d0) from [<c0414cb8>] (hci_uart_tty_receive+0x74/0xa0)
[<c0414cb8>] (hci_uart_tty_receive+0x74/0xa0) from [<c02cbd9c>] (flush_to_ldisc+0x188/0x198)
[<c02cbd9c>] (flush_to_ldisc+0x188/0x198) from [<c00b2774>] (process_one_work+0x144/0x4b8)
[<c00b2774>] (process_one_work+0x144/0x4b8) from [<c00b2e8c>] (worker_thread+0x198/0x468)
[<c00b2e8c>] (worker_thread+0x198/0x468) from [<c00b9bc8>] (kthread+0x98/0xa0)
[<c00b9bc8>] (kthread+0x98/0xa0) from [<c0061744>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Implementation of Read Local AMP Info Command
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Define Extended Flow Specification structures and default values.
Based upon haijun.liu <haijun.liu@atheros.com> series of patches
(sent Sun, 22 Aug 2010)
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Adds definitins for L2CAP header sizes to be uses when calculating
payload size instead of magic numbers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Handle POLL (P) bit in L2CAP ERTM using information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Handle final (F) bit in L2CAP using information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Check frame function uses now information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
L2CAP ERTM txseq calculation uses now information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
reqseq calculation uses now information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Segmentation and Reassembly (SAR) occupies different windows in standard and
extended control fields. Convert hardcoded masks to relative ones and use shift
to access SAR bits.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Supervisory bits occupy different windows in standard / extended control
fields. Convert hardcoded masks to relative ones and use shift to access
S-bit window.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Adds extended control field bit masks and rearrange defines to logical
groups: masks, flags and shift groups.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Adds support for extended window size (EWS) config option. We enable EWS
feature in L2CAP Info RSP when hs enabled. EWS option is included in L2CAP
Config Req if tx_win (which is set via socket) bigger then standard default
value (63) && hs enabled && remote side supports EWS feature.
Using EWS selects extended control field in L2CAP.
Code partly based on Qualcomm and Atheros patches sent upstream a year ago.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
ip_vs_mutext is used by both netns shutdown code and startup
and both implicit uses sk_lock-AF_INET mutex.
cleanup CPU-1 startup CPU-2
ip_vs_dst_event() ip_vs_genl_set_cmd()
sk_lock-AF_INET __ip_vs_mutex
sk_lock-AF_INET
__ip_vs_mutex
* DEAD LOCK *
A new mutex placed in ip_vs netns struct called sync_mutex is added.
Comments from Julian and Simon added.
This patch has been running for more than 3 month now and it seems to work.
Ver. 3
IP_VS_SO_GET_DAEMON in do_ip_vs_get_ctl protected by sync_mutex
instead of __ip_vs_mutex as sugested by Julian.
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We can now move the radiotap header parsing into
ieee80211_monitor_start_xmit(). This moves it out of
the hotpath, and also helps the code since now the
radiotap header will no longer be present in
ieee80211_xmit() etc. which is easier to understand.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The purpose of this is two-fold:
1) by moving it out of tx_data.flags, we can in
another patch move the radiotap parsing so it
no longer is in the hotpath
2) if a device implements fragmentation but can
optionally skip it, the radiotap request for
not doing fragmentation may be honoured
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
role_switch variable inside l2cap_chan is a logical one and can
be easily converted to flag
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
force_active variable inside l2cap_chan is a logical one and can
be easily converted to flag
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
force_reliable variable inside l2cap_chan is a logical one and can
be easily converted to flag
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
flushable variable inside l2cap_chan is a logical one and can
be easily converted to flag. Added flags in l2cap_chan structure.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
To avoid ifdefs in the other code that supports DCB notifiers
add stub routines. This method seems popular in other net code
for example 8021Q.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DCBX mode to event notifiers so listeners can learn
currently enabled mode.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ifindex instead of ifname in the DCB app ring. This makes for a smaller
data structure and faster comparisons. It also avoids possible issues when
a net device is renamed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.
The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
ops.conf_tx = conf_tx_op;
@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
conf_tx_op (
- struct ieee80211_hw *hw,
+ struct ieee80211_hw *hw, struct ieee80211_vif *vif,
u16 queue,
const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recently mac80211 was changed to use nullfunc instead of probe
request for connection monitoring for tx ack status reporting
hardwares. Sometimes in congested network, STA got disconnected
quickly after the association. It was observered that the rate
control was not adopted to environment due to minimal transmission.
As the nullfunc are used for monitoring purpose, these frames should
not be sacrificed for rate control updation. So it is better to send
the monitoring null func frames at minimum rate that could help to
retain the connection.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow injected unicast frames to be sent without having to wait
for an ACK.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the addition of uAPSD and driver buffering
the powersave handling has gotten quite complex.
Add a section to the documentation to explain it
for anyone wanting to implement it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi has a separate EOSP notification from
the device, and to make use of that properly
it needs to be passed to mac80211. To be able
to mix with tx_status_irqsafe and rx_irqsafe
it also needs to be an "_irqsafe" version in
the sense that it goes through the tasklet,
the actual flag clearing would be IRQ-safe
but doing it directly would cause reordering
issues.
This is needed in the case of a P2P GO going
into an absence period without transmitting
any frames that should be driver-released as
in this case there's no other way to inform
mac80211 that the service period ended. Note
that for drivers that don't use the _irqsafe
functions another version of this function
will be required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi needs to know the number of frames that are
going to be sent to a station while it is asleep so
it can properly handle the uCode blocking of that
station.
Before uAPSD, we got by by telling the device that
a single frame was going to be released whenever we
encountered IEEE80211_TX_CTL_POLL_RESPONSE. With
uAPSD, however, that is no longer possible since
there could be more than a single frame.
To support this model, add a new callback to notify
drivers when frames are going to be released.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a PS-poll frame is retried (but was received)
there is no way to detect that since it has no
sequence number. As a consequence, the standard
asks us to not react to PS-poll frames until the
response to one made it out (was ACKed or lost).
Implement this by using the WLAN_STA_SP flags to
also indicate a PS-Poll "service period" and the
IEEE80211_TX_STATUS_EOSP flag for the response
packet to indicate the end of the "SP" as usual.
We could use separate flags, but that will most
likely completely confuse drivers, and while the
standard doesn't exclude simultaneously polling
using uAPSD and PS-Poll, doing that seems quite
problematic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add uAPSD support to mac80211. This is probably not
possible with all devices, so advertising it with
the cfg80211 flag will be left up to drivers that
want it.
Due to my previous patches it is now a fairly
straight-forward extension. Drivers need to have
accurate TX status reporting for the EOSP frame.
For drivers that buffer themselves, the provided
APIs allow releasing the right number of frames,
but then drivers need to set EOSP and more-data
themselves. This is documented in more detail in
the new code itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>