Add support for 16-bit NAND bus-width for the AT91 NAND driver.
The 16-bit NAND is found on the Atmel AT91SAM9260-EK and AT91SAM9261-EK
boards.
Orignal Patch from Patrice Vilchez
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Number of address bytes for 64-128 MiB NANDs is 4, not 5.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Select MTD_NAND_ECC_SMC (ECC byte order according to the Smart Media
Specification) if MTD_NAND_NDFC is used.
Using the wrong byte order causes fatal, unnoticed data damage.
For further information see:
http://lists.infradead.org/pipermail/linux-mtd/2006-November/016920.html
Signed-off-by: Timo Lindhorst <lindhors@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The newly-added cafe_ecc.c had a lot of it because of the way the lookup
table was auto-generated; clean up the other files too while we're at it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix up the config option in the #ifdef statements in nand_ecc.c
Signed-off-by: Timo Lindhorst <lindhors@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As was discussed between Ricard Wanderlöf, David Woodhouse, Artem
Bityutskiy and me, the current API for reading/writing OOB is confusing.
The thing that introduces confusion is the need to specify ops.len
together with ops.ooblen for reads/writes that concern only OOB not data
area. So, ops.len is overloaded: when ops.datbuf != NULL it serves to
specify the length of the data read, and when ops.datbuf == NULL, it
serves to specify the full OOB read length.
The patch inlined below is the slightly updated version of the previous
patch serving the same purpose, but with the new Artem's comments taken
into account.
Artem, BTW, thanks a lot for your valuable input!
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The writel() call accidentally clears all bits in the NDFC_CCR
register (endianess problem). Now __raw_writel() is used instead.
Tested on Bamboo with NAND on chip select 0 and chip select 1.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch converts drivers/mtd/nand/rtc_from4.c to use the new
lib/bitrev.c
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We were resetting cafe->ctl2 to zero after an erase (and also during a
write, but it was correctly reset after that). This meant that ECC reads
after an erase were failing. Doh.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Also use cafe_readl() and cafe_writel() abstraction to make code
slightly cleaner -- especially if we want to use it in PIO mode.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add description of 'raw' in comments for
drivers/mtd/nand/nand_base.c::nand_write_page_syndrome() so 'make xmldocs'
will not spew a warning at us.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Being a value which isn't in the table is a case we explicitly check for
in the caller. Don't BUG_ON() because it does actually happen in
practice.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When a flash-based BBT is not used, nand_default_mark_blockbad() is supposed
to mark the block bad in the oob. However, it sets the wrong length variable
so that no bad block marker is in fact written. This patch attempts to
rectify that.
(As note, it seems to be that logically, it shouldn't be necessary to set
both length variables, as one appears to be for the main buffer, and
one for the oob buffer, but this is how it is done in several places,
including the code for the mtd character device MEMWRITEOOB and MEMREADOOB
ioctls. I'm not sure if this is a temporary solution during some rework of
the mtd infrastructure, or whether there is a deeper thought here.)
Signed-off-by: Ricard Wanderlöf <ricardw@axis.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Ditch the separate oobrbuf and oobwbuf fields from the chip buffers,
and use only a single buffer immediately after the data. This accommodates
NAND controllers such as the OLPC CAFÉ chip, which can't do scatter/gather
DMA so needs the OOB buffer to be contiguous with the data, for both read
and write.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As flash cannot do 0->1 bit transitions when programming, do not do this in
the simulator too. This makes nandsim able to accept subpage writes.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Removes line break after return type in function definitions, to be
consistent with the Linux coding style.
Signed-off-by: Vijay Kumar <vijaykumar@bravegnu.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
For page wise allocation, an array of flash page pointers is allocated
during initialization. The flash pages are themselves allocated when a
write occurs to the page. The flash pages are deallocated when they
are erased.
Signed-off-by: Vijay Kumar <vijaykumar@bravegnu.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch removes code that does chip mapping. The chip mapping code
is no longer used.
Signed-off-by: Vijay Kumar <vijaykumar@bravegnu.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This version only differs from version posted by Savin Zlobec (20 Jun
2006) in that the AT91RM9200-specific chip-select / bus setup code has
been moved from the at91_nand.c driver into the processor-specific file.
From: Savin Zlobec <savin@epico.si>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Updated version of patch, in response to comments from Francois Romieu
<romieu@fr.zoreil.com>
Remove gratuitous casts from iounmap and initialisation of variables.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
- allow high-level nand_write_page() function to be overridden
- likewise low-level write_page_raw() and read_page_raw() functions
- Clean up the abuse of chip->ecc.{write,read}_page() with MTD_OOB_RAW
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Due to this typo, a wrong ECC layout table is chosen.
Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
