The MAC address assignment at module loading is simply forgotten.
The bug at module unloading is caused by an incorrect call.
The bug at module unloading does not only happen for sunqe,
sunlance and sunhme (sbus) suffer from it too.
I've tested this on my SS20.
Signed-off-by: Marcel van Nies <morcles@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 60cba200f1. It's been
linked to lockups of the e1000 hardware, see for example
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=229603
but it's likely that the commit itself is not really introducing the
bug, but just allowing an unrelated problem to rear its ugly head (ie
one current working theory is that the code exposes us to a hardware
race condition by decreasing the amount of time we spend in each NAPI
poll cycle).
We'll revert it until root cause is known. Intel has a repeatable
reproduction on two different machines and bus traces of the hardware
doing something bad.
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg KH <gregkh@suse.de>
Cc: Dave Jones <davej@redhat.com>
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Yukon FE (100mbit only) chips do not support large packets.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon EC Ultra chips have transmit settings for store and
forward and PCI buffering. By setting these appropriately, normal
performance goes from 750Mbytes/sec to 940Mbytes/sec (non-jumbo).
It is also possible to do Jumbo mode, but it means turning off
TSO and checksum offload so the performance gets worse. There isn't
enough buffering for checksum offload to work.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to make sure and disable ASF on all chip types. Otherwise, there may be
random reboots.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There should never be descriptor error unless hardware or driver is buggy.
But if an error occurs, print useful information, clear irq, and recover.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This device is having all sorts of problems that lead to data corruption
and system instability. It gets receive status and data out of order,
it generates descriptor and TSO errors, etc.
Until the problems are resolved, it should not be used by anyone
who cares about there system.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The basic structure of "normal" UDP/IP/Ethernet
frames (that actually work):
- It starts with the Ethernet header (dest MAC, src MAC, etc.)
- The next part is occupied by the IP header (version info, length of
packet, id=0, fragment offset=0, checksum, from / to address, etc.)
- Then comes the UDP header (src / dest port, length, checksum)
- Actual payload
- Ethernet checksum
Now what's different for IP fragment:
- The IP header has id set to some value (same for all fragments),
offset is set appropriately (i.e. 0 for first fragment, following
according to size of other fragments), size is the length of the frame.
- UDP header is unchanged. I.e. length is according to full UDP
datagram, not just the part within the actual frame! But this is only
true within the first frame: all following frames don't have a valid
UDP-header at all.
The spidernet silicon seems to be quite intelligent: It's able to
compute (IP / UDP / Ethernet) checksums on the fly and tests if frames
are conforming to RFC -- at least conforming to RFC on complete frames.
But IP fragments are different as explained above:
I.e. for IP fragments containing part of a UDP datagram it sees
incompatible length in the headers for IP and UDP in the first frame
and, thus, skips this frame. But the content *is* correct for IP
fragments. For all following frames it finds (most probably) no valid
UDP header at all. But this *is* also correct for IP fragments.
The Linux IP-stack seems to be clever in this point. It expects the
spidernet to calculate the checksum (since the module claims to be able
to do so) and marks the skb's for "normal" frames accordingly
(ip_summed set to CHECKSUM_HW).
But for the IP fragments it does not expect the driver to be capable to
handle the frames appropriately. Thus all checksums are allready
computed. This is also flaged within the skb (ip_summed set to
CHECKSUM_NONE).
Unfortunately the spidernet driver ignores that hints. It tries to send
the IP fragments of UDP datagrams as normal UDP/IP frames. Since they
have different structure the silicon detects them the be not
"well-formed" and skips them.
The following one-liner against 2.6.21-rc2 changes this behavior. If the
IP-stack claims to have done the checksumming, the driver should not
try to checksum (and analyze) the frame but send it as is.
Signed-off-by: Norbert Eicker <n.eicker@fz-juelich.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove assumption that PHY interrupts use GPIOs 3 and 5.
Deal with PHY interrupts connected to any GPIO pins.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reuse the incoming skb when a clientless abort req is recieved.
The release of RDMA connections HW resources might be deferred in
low memory situations.
Ensure that no further activity is passed up to the RDMA driver
for these connections.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the Intel 5000 southbridge (aka Intel 6310/6311/6321ESB) PCIe ports
and the Intel E30x0 chipsets to the whitelist of aligned PCIe completion.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simpler way of dealing with the firmware 4KB boundary crossing
restriction for rx buffers. This fixes a variety of memory
corruption issues when using an "uncommon" MTU with a 16KB
page size.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove specific CPL handler.
Add missing CPL handler.
Add missing register setting when the interface is brought up.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The MAC watchdog was failing if the peer interface was brought down.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a deadlock when the interface s configured down and
the watchdog tack is sleeping on rtnl_lock.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to rework wake on lan code to setup properly and get activated
on shutdown (and suspend), not when ethtool is run.
This does not need to go to stable queue because wake on lan
was not even included in 2.6.20 (or earlier versions).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The workaround Yukon EC-U wasn't comparing with correct
version and wasn't doing correct setup. Without it, 88e8056
throws all sorts of errors.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some of these chips are disabled until clock is enabled.
This fixes:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=404107
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver needs to turn off carrier when down.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver needs to turn off carrier when down, otherwise it can
confuse bonding and bridging and looks like carrier is on immediately
when it is brought back up.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The specifications for loopback_gain calculation and for G PHY
initialization have been updated. This patch implements them and
fixes a machine check error that occurs for PPC architecture with a
phy->rev of 1.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In 802.11b/g mode, bcm43xx actively scans channels 1-14 no matter what
locale has been set, either in the sprom or by the locale option. This
behaviorviolates regulatory rules everywhere in the world except
Japan. This patch changes the default range to the correct value if the
locale has been set, and to channels 1-13 if no locale has been set.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to conflicting/confusing defines in the vendor driver, we were
reading E2P_PHY_REG from the wrong location.
CR157 patching was slightly incorrect in that the vendor driver only
patches in an 8-bit value, whereas we were patching 24 bits.
Additionally, CR157 patching was happening on both zd1211 and zd1211b,
but this should only happen on zd1211.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211rw currently detects AL2230S-based devices as AL2230, and hence
programs the RF incorrectly. Transmit silently fails on this
misconfiguration.
After this patch, AL2230S devices are rejected with an error message, to
avoid any confusion with an apparent driver bug.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The spin_lock calls made in dev->open and dev->close must disable
BH since open/close are made in process context. Conversely, the
call in dev->hard_start_xmit does not need to disable BH since it
is already executing with BH disabled.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will crash when the chip has been initialized by EFI before
tg3_init_one(). In this case, the driver will call tg3_chip_reset()
before allocating consistent memory.
The bug is fixed by checking for tp->hw_status before accessing it
during tg3_chip_reset().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PM hooks are no-op if the r8169 interface is down (i.e. !IFF_UP).
However, as the chipset is enabled, the device will not work after a
suspend/resume cycle. The patch always issue the required PCI suspend
sequence and removes the module unload/reload workaround.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The irq handler schedules a NAPI poll request unconditionally as soon as
the status register is not clean. It has been there - and wrong - for
ages but a recent timing change made it apparently easier to trigger.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you set the IFF_ALLMULTI flag on a b44 device, or if you join more than
B44_MCAST_TABLE_SIZE multicast groups, the device will stop receiving unicast
messages. This is because the __b44_set_mac_addr call sets the zeroth CAM
entry to the MAC address of the device, and then the loop at line 1722
proceeds to overwrite it unless the value of i is set by the __b44_load_mcast
call. However, when IFF_ALLMULTI is set, that call is bypassed, leaving i set
to zero.
Fixed by starting the loop at 1 to make it skip the CAM entry for the MAC
address.
Signed-off-by: Bill Helfinstine <bhelf@flitterfly.whirpon.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Run the watchdog task when the link is up.
Flush the XGMAC Tx FIFO when the link drops.
Also remove a statistics update that should have gone
in the previous modification of xgmac.c.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Differentiate NIC only adapters from RNICs.
Initialize offload capabilities for RNICs only.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The nvram dword alignment logic was broken when writing less than 4
bytes on a non-aligned offset. It was missing logic to round the
length to 4 bytes.
The page erase code is also moved so that it is only called when
using non-buffered flash for better code clarity.
Update version to 1.5.7.
Based on initial patch from Tony Cureington <tony.cureington@hp.com>.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses the following issues with the pxa2xx FIr driver:
1. increment overrun error counter and not frame error counter on ICSR1_ROR bit set in ICSR1.
2. drop frames reported with the frame error from the IC.
3. when resetting the receiver and preparing it for the next DMA in pxa_irda_fir_irq() actually clear the Rx FIFO. See description in Table 11-2 in PXA270 Developer's Manual of the RXE bit.
Correction added in version 2: clearing the IC Rx FIFO also has to be done in pxa_irda_fir_dma_tx_irq()
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
NetXen: Fix hardware access for ppc architecture.
sis190: new PHY support
atl1: save mac address on remove
The input_device pointer is not refcounted, which means the device may
disappear while packets are queued, causing a crash when ifb passes packets
with a stale skb->dev pointer to netif_rx().
Fix by storing the interface index instead and do a lookup where neccessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported to work on the WinFast 761GXK8MB-RS motherboard.
Plain 10/100 Mbps.
Signed-off-by: Paul Gibbons <paul@pkami.e7even.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some atl1 boards get their MAC address written directly to the register
by the BIOS during POST, rather than storing it in EEPROM that's
accessible to the driver. If the MAC register on one of these boards
is changed and then the module is unloaded, the permanent MAC address
will be forgotten until the box is rebooted. We should save the
permanent address during removal if we've been messing with it.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bnx2_has_work()'s logic is flawed and can cause the driver to miss
a link event. The fix is to compare the status block's attn_bits
and attn_bits_ack to determine if there is a link event.
Update version to 1.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds checking for allocated DVMA memory and granted IRQ line.
Signed-off-by: Cyrill V. Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In this driver, the default ethernet address is first set by by calling
eth_port_uc_addr_get() which reads the relevant registers of the
corresponding port as initially set by firmware. However that function
used the port_num field accessed through the private area of net_dev
before it was set.
The result was that one board I have ended up with the unicast address
set to 00:00:00:00:00:00 (only port 1 is connected on this board). The
problem appeared after commit 84dd619e4d.
This patch fixes the bug by setting mp->port_num prior to calling
eth_port_uc_get_addr().
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
