Pause settings
- 1G pause was not working due to missing write to the emac block
(TX_MODE_FLOW_EN)
- The flow control should use the negotiated result (after autoneg) so
we should save both the requested autoneg and the result
- The HW credits with flow control at 1G speed were not optimized and
caused low throughput
- It is recommended to turn off flow control if the MTU is bigger than
5000B due to internal buffers size
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link order with external PHY
When external PHY exists (second chip with the PHY to translate to
another physical medium) the link with the eternal PHY and the network
should be established before setting the link between the 5771x and the
PHY. This is the right order and it is important when using autoneg -
the link to the network should use the autoneg and the link between the
two chips should be forced to the network result.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No LRO without Rx checksum
Disabling LRO when Rx checksum is disabled
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong structure size
The wrong structure was used in the sizeof to clear (luckily both
structures have the same size in this version...)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL capability
All designs reported WoL capability regardless of HW limitations - check
if this device is actually capable of WoL
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing MAC addresses filters
When the driver unloads, it should clear the MAC addresses filters in
the HW - this prevents packets from entering the chip when the driver is
re-loaded before initializing the right filters
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay in while loops
The delay in the loop should be after the change. This has very little
effect (can save one delay) but it is the right thing to do
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PBA Table Page Alignment Workaround
The PBA table starts on the middle of the page and that's causing very
low performance with virtualization. The solution is not to update via
the BAR directly but via chip access to the same memory
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Self-test false positive
- The memory test should use a mask according to the chip type
- In the register test, check the port only once and not inside the for
loop (not causing a failure - just ugly)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory allocation
- The CQE ring was allocated to the max size even for a chip that does
not support it. Fixed to allocate according to the chip type to save
memory
- The rx_page_ring was not freed on driver unload
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW attention lock
Making sure that only one function will handle the HW attention. This
makes the device parameter aeu_mask redundant so it is removed
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW lock mechanism
Enhancing the HW lock to work per function and not only per port - this
is needed for the next patch that protects races over HW attention
detection between the different functions. At this chance, changing the
functions names to be more inline with the current naming convention
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load/Unload under traffic
Few issues were found when loading and unloading under traffic:
- When receiving Tx interrupt call netif_wake_queue if the queue is
stopped but the state is open
- Check that interrupts are enabled before doing anything else on the
msix_fp_int function
- In nic_load, enable the interrupts only when needed and ready for it
- Function stop_leading returns status since it can fail
- Add 1ms delay when unloading the driver to validate that there are no
open transactions that already started by the FW
- Splitting the "has work" function into Tx and Rx so the same function
will be used on unload and interrupts
- Do not request for WoL if only resetting the device (save the time
that it takes the FW to set the link after reset)
- Fixing the device reset after iSCSI boot and before driver load - all
internal buffers must be cleared before the driver is loaded
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW Internal Memory structure
The FW uses data structures on the chip internal memory to aggregate the
connections when TPA is enabled. The driver was clearing the wrong offsets
and therefore one function could cause another function to loose packets.
Changing the initialization of the chip internal memory to clear only the
relevant memory for each function which is being loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics
- Making sure that each drop is accounted for in the driver statistics
- Clearing the FW statistics when driver is loaded to prevent
inconsistency with HW statistics
- Once error is detected (bnx2x_panic_dump), stop the statistics
before other actions (currently it is stopped last and can corrupt
the data) - Adding HW checksum error counter to the statistics
- Removing unused variable stats_ticks
- Using macros instead of magic numbers to indicate which statistics are
shared per port and which are per function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not dropping packets with L3/L4 checksum error
Those packets should be passed to the OS. The problem is clear in
forwarding mode.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW (bootcode) interface fixes
- Making sure that the device will not cause kernel panic of the
bootcode is corrupted or missing
- Removing module debug parameter "nomcp" since no one should work
without the bootcode (this is a left over from the chip bring up days)
- Instead of waiting fix amount of time for bootcode response, sample it
every 10ms (usually the answer is ready after less than 10ms)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There doesn't seem to be a compelling reason why atl1e_setup_mac_ctrl()
is marked as "inline":
It's not used in any place where speed would matter much, and as long as
it has only one caller non-ancient gcc versions anyway inline it
automatically.
This patch fixes the following compile error with gcc 3.4:
CC drivers/net/atl1e/atl1e_main.o
atl1e_main.c: In function `atl1e_check_link':
atl1e_main.c:50: sorry, unimplemented: inlining failed in call to
atl1e_main.c:196: sorry, unimplemented: called from here
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5177/1: arm/mach-sa1100/Makefile: remove CONFIG_SA1100_USB
[ARM] 5166/1: magician: add MAINTAINERS entry
[ARM] fix pnx4008 build errors
[ARM] Fix SMP booting with non-zero PHYS_OFFSET
[ARM] 5185/1: Fix spi num_chipselect for lubbock
[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
[ARM] Add support for arch/arm/mach-*/include and arch/arm/plat-*/include
[ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
[ARM] Eliminate useless includes of asm/mach-types.h
[ARM] Fix circular include dependency with IRQ headers
avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>
avr32: Introduce arch/avr32/mach-*/include/mach
avr32: Move include/asm-avr32 to arch/avr32/include/asm
[ARM] sa1100_wdt: use reset_status to remember watchdog reset status
[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage
[ARM] pxa: introduce reset.h for reset specific header information
Fix dubious logical operation that was found by sparse:
linux-next-20080807/drivers/net/bnx2x_main.c:7205:27: warning: dubious: !x & y
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a single enum for managing modes, store supported modes by
the HW in a bitmask.
Register legacy rates with mac80211 only at init.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ath9k_tx_queue_info which contains the same elements,
and merge get/set functions of tx queue properties.
Also, fix whitespace damage in struct ath_softc.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.
Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the new mac80211 11n ath9k Atheros driver. Only STA support
is currently enabled and tested.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove Atheros 11n devices from being claimed by ath5k as its
now handled by ath9k.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
these "magic" values must to be the other way round...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was possible for unsupported operating modes
to be accepted by the add_interface callback function.
This patch will block those modes until proper support
has been implemented for them.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following "mac80211: fix TX sequence numbers", if a packet
has the IEEE80211_TX_CTL_ASSIGN_SEQ assigned, a sequence number must be
supplied, either by hardware or software. AFAIK, no such hardware exists
for the p54, thus it must be done in software. With this patch, a connection
qith p54usb is stable, whereas the interface went off-line in 2-3 hours
without this change. Note that this code will have to be reworked for proper
sequence numbers on beacons. In addition, the sequence number has been placed
in the hardware state, not the vif state.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up iwl_tx_skb function.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It is wrong to destroy a bonding master from a context that uses the sysfs
of that bond. When last IPoIB slave is unenslaved from by writing to a
sysfs file (for bond0 this would be /sys/class/net/bond0/bonding/slaves)
the driver tries to destroy the bond. This is wrong and can lead to a
lockup or a crash. This fix lets the bonding master stay and relies on
the user to destroy the bonding master if necessary (i.e. before module
ib_ipoib is unloaded)
This patch affects only bonds of IPoIB slaves. Ethernet slaves stay
unaffected.
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Refactor mii monitor. As with the previous ARP monitor refactor,
the motivation for this is to handle locking rationally (in this case,
removing conditional locking) and generally clean up the code.
This patch breaks up the monolithic mii monitor into two phases:
an inspection phase, followed by an optional commit phase. The commit phase
is the only portion that requires RTNL or makes changes to state, and is
only called when inspection finds something to change.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some hardware set promisc when they are requested to set IFF_ALLMULTI flag.
It's ok, but if drivers set IFF_PROMISC flag when they set promisc,
it will broken upper layer handle for promisc and allmulti.
In addition, drivers can use their own hardware programming to make it.
So do not allow drivers to set IFF_* flags.
This is a general driver fix, so I didn't split it to pieces and send
to specific driver maintainers.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The dm9000 driver reads the chip's MAC address from the attached EEPROM. When
no EEPROM is present, or when the MAC address is invalid, it falls back to
reading the address from the chip.
This patch lets platform code set the desired MAC address through platform
data.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix possible bug where end of receive buffer could be overwritten.
The allocation needs to allow for the reserved space. This would only happen
if device received packet greater than Ethernet standard MTU.
Change this driver to use netdev_alloc_skb rather than setting skb->dev
directly. For the initial allocation it doesn't need to be GFP_ATOMIC.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reference: https://launchpad.net/bugs/140511
The Belkin bluetooth dongle unfortunately shares the vendor and device id
with the network adapter which causes lockups whenever the bluetooth
dongle is inserted.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_nic_pci_mem_read_direct':
drivers/net/netxen/netxen_nic_hw.c:1414: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'u64'
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_nic_pci_mem_write_direct':
drivers/net/netxen/netxen_nic_hw.c:1487: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'u64'
You don't know what type was used for u64 hence they cannot be printed without
casting.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix all errors and warnings reported by checkpatch.pl
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix all errors and warnings reported by checkpatch.pl
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support SH7619 Internal ethernet controler.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Setup of the mac filter lost the upper 16bit of the mac address. This
bug got unconvered by a patch, which fixed the promiscous handling.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
xen-netfront never called netif_start_queue() and was was waking the
queue on xennet_open(), triggering the BUG_ON() on __netif_schedule().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver was erroneously clearing this bit though the hardware supports multicast.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This device is one side of a two-function adapter (NIC and iSCSI).
Promiscuous mode setting/clearing is not allowed from the NIC side.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For NX3031, multicast filtering, promisc mode, and max frame size
setting is handled by firmware, driver needs to send request to
enable/disable it.
For old chip revisions / firmware, driver still sets it directly.
Added function pointer to set mtu according to chip revision.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Initialize producer and consumer indices during netdev open(), only
for old firmware/chip.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix legacy interrupt mode for NX3031 chips, read pci interrupt state
in hardware to guard against spurious interrupt.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add couple of new board configurations based on NX3031 chip.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For NX3031, the phy is managed by firmware, so driver should avoid
setting any phy registers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The commit that made the CONFIG_GFAR_NAPI code unconditional was
included at the same time as a new CONFIG_GFAR_NAPI user, resulting
in these bugus #ifdef's.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently when we do a packet flood to the Ethernet port, the console
reports error every time when a packet is dropped. This is too
redundant and cost performance. Remove message for this type of event.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for limiting the number of tx pause frames to a
default of 8. Previously, hardware would send out continuous stream of
pause frames.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds jumbo frame support for MCP79 chipsets.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for new tx statistic counters in the hardware -
unicast, multicast, and broadcast
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch enforces a stricter policy on rx errors. The driver needs to
verify whether there are multiple rx errors versus a single error.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the problems reported for 2.6.27-rc1 caused by over aggressive
power management. Turning clock off on PCI Express is problematic for WOL,
and when doing multi-booting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
igb_init_managability does not actually perform any function as the two
registers it attempts to write are both read only on the host. This patch
removes the function and all references to it from the driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Three functions were left in the code that are no longer used. I am removing
these functions just to keep the code clean.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The igb_mta_set function was not being correctly used
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch changes the PCS configuration for serdes so that the flow
control options change be set via the ethtool -A option.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With a fiber or serdes NIC installed the driver was causing a null pointer
dereference on driver unload.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The internal name was used in comments, replaced with silicon part number.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The L1 hardware contains a bug that flags a fragmented IP packet
as having an incorrect TCP/UDP checksum, even though the packet
is perfectly valid and its checksum is correct. There's no way to
distinguish between one of these good packets and a packet that
actually contains a TCP/UDP checksum error, so all we can do is
allow the packet to be handed up to the higher layers and let it
be sorted out there.
Add a comment describing this condition and remove the code that
currently fails to handle what may or may not be a checksum error.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are currently no devices supported by the e1000e driver which need
ioport resources, remove the test for it and all unnecessary code
associated with it (struct e1000_adapter elements, local variables, etc.)
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
a few people seem to have problems maintaining gigabit link
and it was root caused to an interaction between the managability
firmware on the host and the driver, not communicating.
The form of communication they use is the drv_load bit.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
82573 EEPROMs have been shipped out with known issues. While most
people will never see the issues some people do and we know
how to address them. Warn the user if we find one of these
EEPROM issues.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ndev_* printk's are too lenghty and we don't need to specify
the adapter/netdev struct at all, making this a lot more readable.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set 64bits consistent DMA mask since it improves performance
in some cases. No need to check the return value since it is
not required for the driver to work.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (78 commits)
AX.25: Fix sysctl registration if !CONFIG_AX25_DAMA_SLAVE
pktgen: mac count
pktgen: random flow
bridge: Eliminate unnecessary forward delay
bridge: fix compile warning in net/bridge/br_netfilter.c
ipv4: remove unused field in struct flowi (include/net/flow.h).
tg3: Fix 'scheduling while atomic' errors
net: Kill plain NET_XMIT_BYPASS.
net_sched: Add qdisc __NET_XMIT_BYPASS flag
net_sched: Add qdisc __NET_XMIT_STOLEN flag
iwl3945: fix merge mistake for packet injection
iwlwifi: grap nic access before accessing periphery registers
iwlwifi: decrement rx skb counter in scan abort handler
iwlwifi: fix unhandled interrupt when HW rfkill is on
iwlwifi: implement iwl5000_calc_rssi
iwlwifi: memory allocation optimization
iwlwifi: HW bug fixes
p54: Fix potential concurrent access to private data
rt2x00: Disable link tuning in rt2500usb
iwlwifi: Don't use buffer allocated on the stack for led names
...
This patch fixes the 'scheduling while atomic' errors introduced by
commit 12dac0756d ("tg3: adapt tg3 to
use reworked PCI PM code").
The first hunk of the patch removes an unnecessary
tg3_set_power_state() call. The chip will already be in the D0 state
either due to a chip reset or through a previous call to
tg3_set_power_state().
The second hunk of the patch moves the tg3_set_power_state() call
outside the critical section guarded by tg3_full_lock() and
tg3_full_unlock() functions. The power state of the device is and
should be outside the lock's domain and all other
tg3_set_power_state() calls support this.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (29 commits)
sh: enable maple_keyb in dreamcast_defconfig.
SH2(A) cache update
nommu: Provide vmalloc_exec().
add addrespace definition for sh2a.
sh: Kill off ARCH_SUPPORTS_AOUT and remnants of a.out support.
sh: define GENERIC_HARDIRQS_NO__DO_IRQ.
sh: define GENERIC_LOCKBREAK.
sh: Save NUMA node data in vmcore for crash dumps.
sh: module_alloc() should be using vmalloc_exec().
sh: Fix up __bug_table handling in module loader.
sh: Add documentation and integrate into docbook build.
sh: Fix up broken kerneldoc comments.
maple: Kill useless private_data pointer.
maple: Clean up maple_driver_register/unregister routines.
input: Clean up maple keyboard driver
maple: allow removal and reinsertion of keyboard driver module
sh: /proc/asids depends on MMU.
arch/sh/boards/mach-se/7343/irq.c: removed duplicated #include
arch/sh/boards/board-ap325rxa.c: removed duplicated #include
sh/boards/Makefile typo fix
...
We should allow packets transmission in monitor mode for 3945. The
patch fixes a merge error with 2.6.26 kernel.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to grap nic access before accessing periphery registers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch decrements rx skb counter in scan abort handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes unhandled interrupt when HW rfkill is on during
devices start up. The behavior changes, now open is successful even
when rfkill is on. This is to align with the situation when rfkill
is set on after opening.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements rssi calculation for 5000 HW.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch optimizes memory allocation. The cmd member of
iwl_tx_queue was allocated previously as a continuous block
of memory. This patch allocates separate memory chunks for each command
and maps/unmaps these chunks in the run time.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds few HW bug fixes.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Experience with the rtl8187 driver has shown that mac80211 can make
calls to the config callback routine in rapid succession. This patch
creates a mutex that protects the private data in several of the routines
called by mac80211.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the legacy rt2570 driver the link tuner was never
really called. And now the reason has finally become
apparent: It breaks TX capabilities
As soon as the device has been associated all following
TX frames will be queued in the hardware and never transmitted
to the air. Disabling sections of the link tuner did not
have the expected result, but completely disabling the
link tuner did have the right result (Both of my rt2570 devices
came back to life).
This should fix Fedora bug: 411481
v2: Fix typos
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having the buffer on the stack and even re-using it for all led devices is bad.
Not being able to resolve the name member of the led device structure to a
meaningful value leads to confusion during ad-hoc debugging and potential
breakage in the future, if we ever decide to access the name member outside of
the registration function. Move the buffer to our private per led device
structures so that it is accessible after registration.
A quick grep didn't yield any occurence of using the led device name parameter
outside of the led device registration function, so currently we should already
be safe for normal operation.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames driver name from 4965 to AGN
The driver supports both 4965AGN and 5000AGN family
The driver's original module name iwl4965.ko remains as an alias
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes errors reported by checkpatch in iwlwifi drivers
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965-base.c to iwl-agn.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses dtim_period from association, and sets the listen_interval.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl-agn-rs.c: In function 'rs_clear':
iwl-agn-rs.c:2405: warning: unused variable 'priv
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in AGG flow:
u64 bitmap = 0;
bitmap |= 1 << 32 results to be 0xffffffff80000000.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets the led register in disassociation flow according to
rf-kill state : off - in case of rf_kill, on - otherwise.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl4965_fill_rs_info was used in sysfs. This info is already present
in iwl-agn-rs debugfs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl-4965-rs to iwl-agn-rs as it provides
rate scale capability for all AGN capable iwlwifi drivers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_set_pwr_src to iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch concentrates becaon handling in iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_mac_ampdu_action to iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects power_level in sysfs.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for power save for 5000 HW.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00usb_vendor_request_large_buff is write-only, so it is
safe to make the argument a const.
Fixes compile warning:
drivers/net/wireless/rt2x00/rt73usb.c: In function 'rt73usb_load_firmware':
drivers/net/wireless/rt2x00/rt73usb.c:916: warning: passing argument 5 of 'rt2x00usb_vendor_request_large_buff' discards qualifiers from pointer target typ
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some module parameters with only one line have the '\n' at the end of the
description. This is not needed nor wanted as after the description the
type (i.e. int) is followed by a newline.
Some modules contain a multi-line description, these are not affected
by this patch.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Ed L. Cashin <ecashin@coraid.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Roland Dreier <rolandd@cisco.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asm/se.h moved to mach-se/mach/se.h, update the path. We could use
mach/se.h here also, but it's preferable to be explicit when there's
only a single supported mach-type.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
iwl3945_rx_reply_rx was sending packets too early to
mac80211, before updating signal strength/quality.
This resulted in garbage power levels.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the standard offsetof() macro to fix a compile warning below:
CC [M] drivers/net/wireless/prism54/isl_ioctl.o
drivers/net/wireless/prism54/isl_ioctl.c: In function 'prism2_ioctl_set_generic_element':
drivers/net/wireless/prism54/isl_ioctl.c:2658: warning: cast from pointer to integer of different size
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipw_write8() can't be used alone with a loop because of a wrong definition.
CC [M] drivers/net/wireless/ipw2200.o
drivers/net/wireless/ipw2200.c: In function 'ipw_ethtool_set_eeprom':
drivers/net/wireless/ipw2200.c:10579: warning: array subscript is above array bounds
drivers/net/wireless/ipw2200.c: In function 'ipw_load':
drivers/net/wireless/ipw2200.c:2663: warning: array subscript is above array bounds
Add missing do {} while (0) to fix them.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some users of the RTL8187B have experienced difficulties since commit
49292d5635 that introduced the power
management wext hooks. This difficulty has not made much sense until
it was realized that it was possible for mac80211 to make a call to the
config routine while that routine was already being executed. On this
device, it is necessary to loopback the TX when changing channels. Unless
this is properly restored, the device will lockup. A mutex now protects
the device state, and the private data in several places.
The problem was found by Herton Ronaldo Krzesinski <herton@mandriva.com.br>,
who also suggested this type of fix.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In kernel version 2.6.26-rc9 my wireless LAN card worked; but in the
released 2.6.26, my RaLink rt2500 card wouldn't associate.
Git-bisect led me to this patch:
61486e0f68
rt2x00: Remove ieee80211_tx_control argument from write_tx_desc()
I believe that there is a problem with that patch --- it
(inadvertantly) removes an extra line of code, that used to set the
DATABYTE_COUNT field.
This patch reinstates that line, and with it my card works again.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since only mesh-enabled firmware has the CMD_802_11_MONITOR_MODE on
which the rtap functionality depends, only expose the rtap functionality
when mesh is also available.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sequence counter can be accessed in IRQ context,
which means the lock protecting the counter should
be irqsave. To prevent making the entire intf->lock irqsave
without reason, create a new lock which only protects
the sequence counter.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM_BBPTUNE_VGC word is valid, we should
override EEPROM_BBPTUNE_VGCLOWER field with the BBP
value.
And we should _not_ do that when EEPROM_BBPTUNE_R17 is valid.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the hardware has indicated the firmware upload has completed
and the device is ready, we should wait another millisecond to
make sure the device is really ready to continue.
Without this timout, bringing the interface down and up again will
fail due to incorrect register initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The if-statement to determine the new TX/RX antenna
configuration was incomplete. It lacks the general
else-clause when the antenna wasn't changed.
This is a correct event, since it can occur when only
one of the antenna's has been changed or when the new
configuration is being forced (like when the interface
has just been added).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although most rt2x00 debugfs files don't contain
information which could compromise network security,
it is better to set the access permissions to root only.
This will be required when HW crypto is implemented,
because it could be possible to read the HW key from
the registers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids stopping queue in the middle of the fragmented packet.
It is required that there will be ~10 (max packet/min fragment) or 16
(4 bits of frag number) free tfds all the time.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mask out previously demanded interrupt flags because we set
new ones. Don't allow mixing them after switch from sta to
ibss and vice versa.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Enable I/Q calibration each time we have correction results (we
were only enabling calibration during reset). If we don't we commit
the same results each time calibration routine is called.
* Add some documentation and a TODO on nf calibration
* Return -EAGAIN on noise floor timeout/failure
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add channel function for RF2425 (got this from decompiling binary
HAL, i have no idea why there is a 5GHz section but i'm looking
into it)
* Update RF5112 channel function (also got this from decompiling binary HAL)
* Set JAPAN setting for channel 14 on all PHY chips
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add initial RF gain settings for RF2425
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update ath5k_hw_reset and add some more documentation about PHY calibration
* Fix ath5k_hw_set_power to use AR5K_SLEEP_CTL_SLE_ALLOW for Network sleep
* Preserve sleep duration field while setting AR5K_SLEEP_CTL
and reduce delays & checks for register's status (got this from
decompiling & dumps, it works for me but it needs testing)
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Do an ADC test during reset to match recent regdumps
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update hw_reset to calculate some of the values we were using as static
* Increase activation to rx delay
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Correctly attach RF2425
* Update SREV values for Radio chips
* Update hw_attach to use new SPENDING values
* Write a bit after POST for some chips
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Restore saved initial value after POST
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update list of registers
* Use updated register macros inside hw.c, initvals.c and debug.c
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When support for multiple TX queues were added, the
netif_tx_lock() routines we converted to iterate over
all TX queues and grab each queue's spinlock.
This causes heartburn for lockdep and it's not a healthy
thing to do with lots of TX queues anyways.
So modify this to use a top-level lock and a "frozen"
state for the individual TX queues.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate and free everyting outside of the locked section.
Spotted-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Fixed-by: Seguier Regis <rseguier@e-teleport.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
It should help people fix the bugs in my code :o)
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is necessary to set the dongle type on the nsc driver in order to get
it to work correctly. Thinkpads all appear to use dongle type 9. This
patch defaults nsc devices with an IBM PnP descriptor to use type 9.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Adapt the tg3 driver to use the reworked PCI PM and make it use the
exported PCI PM core functions instead of accessing the PCI PM registers
directly by itself.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SH7763 has Ethernet core same as SH7710/SH7712.
Positions of some registry are different, but the basic part is the same.
I add support of ethernet of sh7763 to sh_eth.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Trying to build with CONFIG_NE2000=m fails with:
scripts/mod/modpost -o /tmp/tmp/linux-2.6.27-rc1/Module.symvers -S -s
ERROR: "NS8390_init" [drivers/net/ne.ko] undefined!
This is because the split of 8390 into pausing and non-pausing
versions was incompletely propagated to ne.c. This fixes it.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dm_{read,write}() were doing USB transfers of data on stack, which isn't
allowed. Fix it by kmalloc'ing a temporary buffer.
Clean up the error handling for short transfers while we're at it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The callers of niu_ethflow_to_class expect zero as error, but it returns
-1 instead.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On s2io driver, when you change the interface MTU, it invokes a card
reset, which flush some statistics. This patch solves this problem, and
also set the net_device->stats as the default statistics structure,
instead of s2io_nic->stats.
To do that, s2io_nic->stats turned into a staging area, where is saved
statistics of the last hardware statistics query. So, the difference
between the current hardware statistics and s2io_nic->stats, is the
value that should be summed up, in order to get the correct statistics
value, even after a reset.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Recent changes to the IRQ framework have made passing the wrong
trigger type to request_irq() become a fatal error. In the case
of the enc28j60 driver, it stopped working in my test harness.
(Specifically: the signal detects "pin change" events, both edges,
not just falling edges. Similarly, other boards might route it
through an inverter. Trigger type are board-specific.)
This fixes that problem by the usual fix of expecting board setup
code to have set up the correct IRQ trigger type. The best known
example of that being x86 setup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Starting with FW version 7.0, the driver needs to allow larger images.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reprogram MAC address after resume from Suspend Mem
(Blackfin Hibernate looses all CORE and SYSTEM register content)
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for the realtek 8211c phy. The driver must
perform a hardware reset of the phy due to an errata where the phy could
not detect the link.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless statistics produced by the RTL8187B driver are not particularly
informative about the strength of the received signal. From the data sheet
provided by Realtek, I discovered that certain parts of the RX header
should have the information necessary to calculate signal quality and
strength. With testing, it became clear that most of these quantities were
very jittery - only the AGC correlated with the signals expected from nearby
AP's. As a result, the quality and strength are derived from the agc value.
The scaling has been determined so that the numbers are close to those
obtained by b43 under the same conditions. The results are qualitatively
correct.
Statistics derived for the RTL8187 have not been changed.
The RX header variables have been renamed to match the quantites described
in the Realtek data sheet.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: fix TX sequence numbers" broke rtl8187. This
patch makes the same kind of fix that was done for rt2x00. Note that
this code will have to be reworked for proper sequence numbers on beacons.
In addition, the sequence number has been placed in the hardware state,
not the vif state.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/mac80211_hwsim.c:503:20: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ia64:
drivers/net/wireless/iwlwifi/iwl-led.c: In function `iwl_get_blink_rate':
drivers/net/wireless/iwlwifi/iwl-led.c:271: warning: long long int format, s64 arg (arg 6)
drivers/net/wireless/iwlwifi/iwl-led.c:271: warning: long long int format, u64 arg (arg 7)
We do not know what type the architecture uses to impement u64 and s64,
hence we must cast the variables for printing.
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the queues are being initialized the entry flags fields must be
reset to 0. When this does not happen some entries might still be
marked as "occupied" after an ifdown & ifup cycle which would trigger
errors when the entry is being accessed:
phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Please file bug report to http://rt2x00.serialmonkey.com.
This also fixes the mac80211 warning:
------------[ cut here ]------------
WARNING: at net/mac80211/tx.c:1238 ieee80211_master_start_xmit+0x30a/0x350 [mac80211]()
which was triggered by the queue error.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00 will only perform configuration changes from
mac80211 when the configuration option has changed.
This means it keeps track of the current active configuration
and will check these values when the config() callback function
is used.
However this causes breakage when the interface has been
brought down and up again, since all stored active values
aren't reset while the registers might have.
This is for example the case with rt61pci antenna registers which
will jump to invalid values when the interface has been started.
To make sure a full configuration takes place after the start()
callback function, a new flag is added which will be checked
during config() and skips the "what's changed" phase.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending the RTS/CTS frame fails, we should
free the skb buffer which was created.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When IEEE80211_TX_CTL_ASSIGN_SEQ is not set,
the driver should disable hardware sequence counting
to make sure the mac80211 provided counter is used.
This fixes QOS sequence counting, since that is one
of the cases where mac80211 provides a seperate
sequence counter.
By moving the sequence counting code to rt2x00queue
we make sure that _all_ frames get the sequence counter,
including RTS/CTS and Beacon frames.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting up a beacon template, the length of the beacon is
calculated with the assumption that the SKB already contains
the Tx descriptor. In the case of beacons it doesn't.
This patch undoes the damage by adding the Tx descriptor length
to the beacon length. This is safe, because the shortest possible
beacon is longer than the Tx header.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Switches rt73usb to use large vendor requests for firmware
and beacons. This also fixes the garbled beacon bug.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds an extra rt2x00 vendor request function to support register
transfers beyond the CSR_CACHE_SIZE / USB packet size limit. This
is useful for firmware uploads, beacon templates and keys, all
of which are to large to do with a single USB request.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Olivier reported a difference between the EIFS
values used in the legacy driver and the one in
the rt2x00 drivers.
In rt2x00 the value was
( SIFS + (8 * (IEEE80211_HEADER + ACK_SIZE)) )
which comes down to 314us while the legacy driver uses the value 364us
This was caused because EIFS is: SIFS + DIFS + AckTime
This patch will fix this by adding the DIFS by the above value,
and creating a SHORT_EIFS define which uses the SHORT_DIFS.
Reported-by: Olivier Cornu <o.cornu@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MSI is a nice thing, but we cannot enable it without changing the
interrupt handler. If we do it, we break MSI capable hardware,
specifically AR5006 chipset.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_beacon_update takes sc->lock upon entry. However, it is only
called from within ath5k_config_interface, which already holds the lock.
Remove the unnecessary locking from ath5k_beacon_update.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/iwlwifi/iwl-scan.o
drivers/net/wireless/iwlwifi/iwl-scan.c: In function 'iwl_rx_scan_complete_notif':
drivers/net/wireless/iwlwifi/iwl-scan.c:274: warning: unused variable 'scan_notif'
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/iwlwifi/iwl-rfkill.o
drivers/net/wireless/iwlwifi/iwl-led.c: In function 'iwl_led_brightness_set':
drivers/net/wireless/iwlwifi/iwl-led.c:198: error: 'led_type_str' undeclared (first use in this function)
drivers/net/wireless/iwlwifi/iwl-led.c:198: error: (Each undeclared identifier is reported only once
drivers/net/wireless/iwlwifi/iwl-led.c:198: error: for each function it appears in.)
The problem is that led_type_str is defined under CONFIG_IWLWIFI_DEBUG
while IWL_DEBUG is a static inline function in this case. Replace it
with macro.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some persistent settings were using hex and others decimal. In some cases,
values were set in hex but reported in decimal. Confusing.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building the wireless-next-2.6 tree with CONFIG_IWL3945 (for building
iwl-3945 driver) and where CONFIG_IWL3945_LEDS is not set,
we get this warning:
drivers/net/wireless/iwlwifi/iwl-3945.c: In function
'iwl3945_pass_packet_to_mac80211':
drivers/net/wireless/iwlwifi/iwl-3945.c:633: warning: unused variable 'hdr'
This patch adds #ifdef to iwl3945_pass_packet_to_mac80211() to avoid this
warning. (The variable 'hdr' is used only if CONFIG_IWL3945_LEDS is set)
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helge Deller reports that HP laptops (NC4010 and NC6000) use active-
high signals to turn on the LEDs. Previous code used active-low for
all devices.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- free and re-request irq since it might have changed during suspend
- disable and enable msi
- don't set D0 state of the device, it's already done by the PCI layer
- do restore_state before enable_device, it's safer
- check ath5k_init return value
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't sync
- coherent mapping (descriptors)
- before unmap, it's useless
- (wrongly anyway -- for_cpu) beacon skb, it's just mapped,
so by the device yet
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that the irq is not in progress after stop. This means
two things:
- ensure the intr setting register is set by flushing posted values
- call synchronize_irq() after that
Also flush stop tx write, inform callers of the tx stop about still
pending transfers (unsuccessful stop) and finally don't wait another
3ms in ath5k_rx_stop, since ath5k_hw_stop_rx_dma ensures transfer to
be finished.
Make sure all writes will be ordered in respect to locks by mmiowb().
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't forget to kill tasklets on stop to not panic if they
fire after freeing some structures.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When signal is noisy, hardware can use all RX buffers and since the last
entry in the list is self-linked, it overwrites the entry until we link
new buffers.
Ensure that we don't free this last one until we are 100% sure that it
is not used by the hardware anymore to not cause memory curruption as
can be seen below.
This is done by checking next buffer in the list. Even after that we
know that the hardware refetched the new link and proceeded further
(the next buffer is ready) we can finally free the overwritten buffer.
We discard it since the status in its descriptor is overwritten (OR-ed
by new status) too.
=============================================================================
BUG kmalloc-4096: Poison overwritten
-----------------------------------------------------------------------------
INFO: 0xffff810067419060-0xffff810067419667. First byte 0x8 instead of 0x6b
INFO: Allocated in dev_alloc_skb+0x18/0x30 age=1118 cpu=1 pid=0
INFO: Freed in skb_release_data+0x85/0xd0 age=1105 cpu=1 pid=3718
INFO: Slab 0xffffe200019d0600 objects=7 used=0 fp=0xffff810067419048 flags=0x40000000000020c3
INFO: Object 0xffff810067419048 @offset=4168 fp=0xffff81006741c120
Bytes b4 0xffff810067419038: 4f 0b 02 00 01 00 00 00 5a 5a 5a 5a 5a 5a 5a 5a O.......ZZZZZZZZ
Object 0xffff810067419048: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Object 0xffff810067419058: 6b 6b 6b 6b 6b 6b 6b 6b 08 42 30 00 00 0b 6b 80 kkkkkkkk.B0...k.
Object 0xffff810067419068: f0 5d 00 4f 62 08 a3 64 00 0c 42 16 52 e4 f0 5a 360].Ob.243d..B.R344360Z
Object 0xffff810067419078: 68 81 00 00 7b a5 b4 be 7d 3b 8f 53 cd d5 de 12 h...{245264276};.S315325336.
Object 0xffff810067419088: 96 10 0b 89 48 54 23 41 0f 4e 2d b9 37 c3 cb 29 ....HT#A.N-2717303313)
Object 0xffff810067419098: d1 e0 de 14 8a 57 2a cc 3b 44 0d 78 7a 19 12 15 321340336..W*314;D.xz...
Object 0xffff8100674190a8: a9 ec d4 35 a8 10 ec 8c 40 a7 06 0a 51 a7 48 bb 2513543245250.354.@247..Q247H273
Object 0xffff8100674190b8: 3e cf a1 c7 38 60 63 3f 51 15 c7 20 eb ba 65 30 >ϡ3078`c?Q.307.353272e0
Redzone 0xffff81006741a048: bb bb bb bb bb bb bb bb 273273273273273273273273
Padding 0xffff81006741a088: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ
Pid: 3297, comm: ath5k_pci Not tainted 2.6.26-rc8-mm1_64 #427
Call Trace:
[<ffffffff802a7306>] print_trailer+0xf6/0x150
[<ffffffff802a7485>] check_bytes_and_report+0x125/0x180
[<ffffffff802a75dc>] check_object+0xac/0x260
[<ffffffff802a9308>] __slab_alloc+0x368/0x6d0
[<ffffffff80544f82>] ? wireless_send_event+0x142/0x310
[<ffffffff804b1bd4>] ? __alloc_skb+0x44/0x150
[<ffffffff80544f82>] ? wireless_send_event+0x142/0x310
[<ffffffff802aa853>] __kmalloc_track_caller+0xc3/0xf0
[<ffffffff804b1bfe>] __alloc_skb+0x6e/0x150
[... stack snipped]
FIX kmalloc-4096: Restoring 0xffff810067419060-0xffff810067419667=0x6b
FIX kmalloc-4096: Marking all objects used
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot this in the previous patch that made it unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The addition of an argument to dma_mapping_error() in commit
8d8bb39b9e "dma-mapping: add the device
argument to dma_mapping_error()" left a bit of fallout:
drivers/net/ibmveth.c:263: error: too few arguments to function 'dma_mapping_error'
drivers/net/ibmveth.c:264: error: expected ')' before 'goto'
drivers/net/ibmveth.c:284: error: expected expression before '}' token
drivers/net/ibmveth.c:297: error: too few arguments to function 'dma_mapping_error'
drivers/net/ibmveth.c:298: error: expected ')' before 'dma_unmap_single'
drivers/net/ibmveth.c:306: error: expected expression before '}' token
drivers/net/ibmveth.c:491: error: too few arguments to function 'dma_mapping_error'
drivers/net/ibmveth.c:927: error: too few arguments to function 'dma_mapping_error'
drivers/net/ibmveth.c:927: error: expected ')' before '{' token
drivers/net/ibmveth.c:974: error: expected expression before '}' token
drivers/net/ibmveth.c:914: error: label 'out' used but not defined m
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4: Update/add Mellanox Technologies copyright lines to mlx4 driver files
mlx4_core: Add VLAN tag field to WQE control segment struct
RDMA/nes: CM connection setup/teardown rework
IPoIB: Correct help text for INFINIBAND_IPOIB_DEBUG
IPoIB/cm: Connected mode is no longer EXPERIMENTAL
RDMA/ucm: BKL is not needed for ib_ucm_open()
RDMA/ucma: BKL is not needed for ucma_open()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (39 commits)
[PATCH] fix RLIM_NOFILE handling
[PATCH] get rid of corner case in dup3() entirely
[PATCH] remove remaining namei_{32,64}.h crap
[PATCH] get rid of indirect users of namei.h
[PATCH] get rid of __user_path_lookup_open
[PATCH] f_count may wrap around
[PATCH] dup3 fix
[PATCH] don't pass nameidata to __ncp_lookup_validate()
[PATCH] don't pass nameidata to gfs2_lookupi()
[PATCH] new (local) helper: user_path_parent()
[PATCH] sanitize __user_walk_fd() et.al.
[PATCH] preparation to __user_walk_fd cleanup
[PATCH] kill nameidata passing to permission(), rename to inode_permission()
[PATCH] take noexec checks to very few callers that care
Re: [PATCH 3/6] vfs: open_exec cleanup
[patch 4/4] vfs: immutable inode checking cleanup
[patch 3/4] fat: dont call notify_change
[patch 2/4] vfs: utimes cleanup
[patch 1/4] vfs: utimes: move owner check into inode_change_ok()
[PATCH] vfs: use kstrdup() and check failing allocation
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix ip_rt_frag_needed rt_is_expired
netfilter: nf_conntrack_extend: avoid unnecessary "ct->ext" dereferences
netfilter: fix double-free and use-after free
netfilter: arptables in netns for real
netfilter: ip{,6}tables_security: fix future section mismatch
selinux: use nf_register_hooks()
netfilter: ebtables: use nf_register_hooks()
Revert "pkt_sched: sch_sfq: dump a real number of flows"
qeth: use dev->ml_priv instead of dev->priv
syncookies: Make sure ECN is disabled
net: drop unused BUG_TRAP()
net: convert BUG_TRAP to generic WARN_ON
drivers/net: convert BUG_TRAP to generic WARN_ON
make it atomic_long_t; while we are at it, get rid of useless checks in affs,
hfs and hpfs - ->open() always has it equal to 1, ->release() - to 0.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
