mthca_free_err_wqe() currently treats both send and receive CQEs
identically if a QP is using an SRQ. But for Tavor hardware, send
CQEs with error can be chained together even if the RQ is part of SRQ,
so we may miss some CQEs.
Fix by following the WQE chain for all send CQEs even for non-SRQ QPs.
This fixes crashes in IPoIB CM:
<https://bugs.openfabrics.org//show_bug.cgi?id=604>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/cm: Improve local id allocation
IPoIB/cm: Fix SRQ WR leak
IB/ipoib: Fix typos in error messages
IB/mlx4: Check if SRQ is full when posting receive
IB/mlx4: Pass send queue sizes from userspace to kernel
IB/mlx4: Fix check of opcode in mlx4_ib_post_send()
mlx4_core: Fix array overrun in dump_dev_cap_flags()
IB/mlx4: Fix RESET to RESET and RESET to ERROR transitions
IB/mthca: Fix RESET to ERROR transition
IB/mlx4: Set GRH:HopLimit when sending globally routed MADs
IB/mthca: Set GRH:HopLimit when building MLX headers
IB/mlx4: Fix check of max_qp_dest_rdma in modify QP
IB/mthca: Fix use-after-free on device restart
IB/ehca: Return proper error code if register_mr fails
IPoIB: Handle P_Key table reordering
IB/core: Use start_port() and end_port()
IB/core: Add helpers for uncached GID and P_Key searches
IB/ipath: Fix potential deadlock with multicast spinlocks
IB/core: Free umem when mm is already gone
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the IB spec, a QP can be moved from RESET to the ERROR
state, but mthca firmware does not support this and returns an error if
we try. Work around this FW limitation by moving the QP from RESET to
INIT with dummy parameters and then transitioning from INIT to ERROR.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Global CM packets used by rmda_cm were being sent with a GRH:hopLimit
of zero, causing them to be dropped by the router. The problem is a
missing initialization of the hop_limit field in mthca_read_ah(),
which was called by build_mlx_header() when sending a MAD on QP1.
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_cq_clean() updates the CQ consumer index without moving CQEs
back to HW ownership. As a result, the same WRID might get reported
twice, resulting in a use-after-free. This was observed in IPoIB CM.
Fix by moving all freed CQEs to HW ownership.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=617>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix posting lists of > 255 receive WRs for Tavor: rq.next_ind must
be updated each doorbell, otherwise the next doorbell will use an
incorrect index.
Found by Ronni Zimmermann at Mellanox.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export ib_umem_get()/ib_umem_release() and put low-level drivers in
control of when to call ib_umem_get() to pin and DMA map userspace,
rather than always calling it in ib_uverbs_reg_mr() before calling the
low-level driver's reg_user_mr method.
Also move these functions to be in the ib_core module instead of
ib_uverbs, so that driver modules using them do not depend on
ib_uverbs.
This has a number of advantages:
- It is better design from the standpoint of making generic code a
library that can be used or overridden by device-specific code as
the details of specific devices dictate.
- Drivers that do not need to pin userspace memory regions do not
need to take the performance hit of calling ib_mem_get(). For
example, although I have not tried to implement it in this patch,
the ipath driver should be able to avoid pinning memory and just
use copy_{to,from}_user() to access userspace memory regions.
- Buffers that need special mapping treatment can be identified by
the low-level driver. For example, it may be possible to solve
some Altix-specific memory ordering issues with mthca CQs in
userspace by mapping CQ buffers with extra flags.
- Drivers that need to pin and DMA map userspace memory for things
other than memory regions can use ib_umem_get() directly, instead
of hacks using extra parameters to their reg_phys_mr method. For
example, the mlx4 driver that is pending being merged needs to pin
and DMA map QP and CQ buffers, but it does not need to create a
memory key for these buffers. So the cleanest solution is for mlx4
to call ib_umem_get() in the create_qp and create_cq methods.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Convert to NAPI
IB: Return "maybe missed event" hint from ib_req_notify_cq()
IB: Add CQ comp_vector support
IB/ipath: Fix a race condition when generating ACKs
IB/ipath: Fix two more spin lock problems
IB/fmr_pool: Add prefix to all printks
IB/srp: Set proc_name
IB/srp: Add orig_dgid sysfs attribute to scsi_host
IPoIB/cm: Don't crash if remote side uses one QP for both directions
RDMA/cxgb3: Support for new abort logic
RDMA/cxgb3: Initialize cpu_idx field in cpl_close_listserv_req message
RDMA/cxgb3: Fail qp creation if the requested max_inline is too large
RDMA/cxgb3: Fix TERM codes
IPoIB/cm: Fix error handling in ipoib_cm_dev_open()
IB/ipath: Don't corrupt pending mmap list when unmapped objects are freed
IB/mthca: Work around kernel QP starvation
IB/ipath: Don't put QP in timeout queue if waiting to send
IB/ipath: Don't call spin_lock_irq() from interrupt context
The semantics defined by the InfiniBand specification say that
completion events are only generated when a completions is added to a
completion queue (CQ) after completion notification is requested. In
other words, this means that the following race is possible:
while (CQ is not empty)
ib_poll_cq(CQ);
// new completion is added after while loop is exited
ib_req_notify_cq(CQ);
// no event is generated for the existing completion
To close this race, the IB spec recommends doing another poll of the
CQ after requesting notification.
However, it is not always possible to arrange code this way (for
example, we have found that NAPI for IPoIB cannot poll after
requesting notification). Also, some hardware (eg Mellanox HCAs)
actually will generate an event for completions added before the call
to ib_req_notify_cq() -- which is allowed by the spec, since there's
no way for any upper-layer consumer to know exactly when a completion
was really added -- so the extra poll of the CQ is just a waste.
Motivated by this, we add a new flag "IB_CQ_REPORT_MISSED_EVENTS" for
ib_req_notify_cq() so that it can return a hint about whether the a
completion may have been added before the request for notification.
The return value of ib_req_notify_cq() is extended so:
< 0 means an error occurred while requesting notification
== 0 means notification was requested successfully, and if
IB_CQ_REPORT_MISSED_EVENTS was passed in, then no
events were missed and it is safe to wait for another
event.
> 0 is only returned if IB_CQ_REPORT_MISSED_EVENTS was
passed in. It means that the consumer must poll the
CQ again to make sure it is empty to avoid the race
described above.
We add a flag to enable this behavior rather than turning it on
unconditionally, because checking for missed events may incur
significant overhead for some low-level drivers, and consumers that
don't care about the results of this test shouldn't be forced to pay
for the test.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API. Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value. Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.
We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity. This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With mthca, RC QPs can starve each other and even UD QPs on the same
hardware schedule queue. As a result, userspace MPI can starve
e.g. IPoIB traffic, with netdev watchdog warnings getting printed out,
and TCP connections getting stuck or failing.
Reduce the chance of this happening by using three separate hardware
schedule queues: one for userspace RC QPs, one for kernel RC QPs, and
one for all other QPs.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All RDMA drivers except ehca set class_dev->dev to their dma_device
value (ehca leaves this unset). dma_device is the only value that
makes any sense, so move this assignment to core/sysfs.c. This reduce
the duplicated code in the rest of the drivers and gives ehca a nice
/sys/class/infiniband/ehcaX/device symlink.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_free_qp() already has local variables to hold the QP's send_cq
and recv_cq, so we can slightly clean up the calls to mthca_cq_clean()
by using those local variables instead of expressions like
to_mcq(qp->ibqp.send_cq).
Also, by cleaning the recv_cq first, we can avoid worrying about
whether the QP is attached to an SRQ for the second call, because we
would only clean send_cq if send_cq is not equal to recv_cq, and that
means send_cq cannot have any receive completions from the QP being
destroyed.
All this work even improves the generated code a bit:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-5 (-5)
function old new delta
mthca_free_qp 510 505 -5
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit b2875d4c ("IB/mthca: Always fill MTTs from CPU") causes a crash
in mthca_write_mtt() with non-memfree HCAs that have their memory
hidden (that is, have only two PCI BARs instead of having a third BAR
that allows access to the RAM attached to the HCA) on 64-bit
architectures. This is because the commit just before, c20e20ab
("IB/mthca: Merge MR and FMR space on 64-bit systems") makes
dev->mr_table.fmr_mtt_buddy equal to &dev->mr_table.mtt_buddy and
hence mthca_write_mtt() tries to write directly into the HCA's MTT
table. However, since that table is in the HCA's memory, this is
impossible without the PCI BAR that gives access to that memory.
This causes a crash because mthca_tavor_write_mtt_seg() basically
tries to dereference some offset of a NULL pointer. Fix this by
adding a test of MTHCA_FLAG_FMR in mthca_write_mtt() so that we always
use the WRITE_MTT firmware command rather than writing directly if
FMRs are not enabled.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In mthca_arbel_fmr_unmap(), the high bits of the key are masked off.
This gets rid of the effect of adjust_key(), which makes sure that
bits 3 and 23 of the key are equal when the Sinai throughput
optimization is enabled, and so it may happen that an FMR will end up
with bits 3 and 23 in the key being different. This causes data
corruption, because when enabling the throughput optimization, the
driver promises the HCA firmware that bits 3 and 23 of all memory keys
will always be equal.
Fix by re-applying adjust_key() after masking the key.
Thanks to Or Gerlitz for reproducing the problem, and Ariel Shahar for
help in debug.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit c20e20ab ("IB/mthca: Merge MR and FMR space on 64-bit systems")
swapped the number of MTTs and MPTs when initializing the MR table. As
a result, we get a kernel oops when the number of MTT segments
allocated exceeds 0x20000.
Noted by Troy Benjegerdes <troy@scl.ameslab.gov>, and reproduced by
Dotan Barak <dotanb@mellanox.co.il>. This fixes
https://bugs.openfabrics.org/show_bug.cgi?id=490
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The garbled logic in mthca_alloc_memfree() causes it to return 0, even
if it fails to allocate all doorbell records. Fix it to return -ENOMEM
when it fails.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes the needlessly global functions mthca_tavor_write_mtt_seg()
and mthca_arbel_write_mtt_seg() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The change to allow allocating ICM chunks from coherent memory did not
increment the count of sg entries properly, so a chunk that required
more than allocation would not be mapped properly by the HCA.
Fix this by adding the missing increment of chunk->nsg.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
RESET->RESET is an allowed QP state transition, so mthca should handle
it correctly, by just returning success without involving the firmware.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Speed up memory registration by filling in MTTs directly when the CPU
can write directly to the whole table (all mem-free cards, and to
Tavor mode on 64-bit systems with the patch I posted earlier). This
reduces the number of FW commands needed to register an MR by at least
a factor of 2 and speeds up memory registration significantly.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For Tavor, we currently reserve separate MPT and MTT space for FMRs to
avoid abusing the vmalloc space on 32 bit kernels. No such problem
exists on 64 bit kernels so let's not do it there.
This way we have a shared pool for MR and FMR resources, used on
demand. This will also make it possible to write MTTs for regular
regions directly from driver.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We allocate the MTT table with alloc_pages() and then do pci_map_sg(),
so we must call pci_dma_sync_sg() after the CPU writes to the MTT
table. This works since the device will never write MTTs on mem-free
HCAs, once we get rid of the use of the WRITE_MTT firmware command.
This change is needed to make that work, and is an improvement for
now, since it gives FMRs a chance at working.
For MPTs, both the device and CPU might write there, so we must
allocate DMA coherent memory for these.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
MTTs are allocated in non-cache-coherent memory, so we must give
reserved MTTs their own cache line, to prevent both device and
CPU from writing into the same cache line at the same time.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The reserved_mtts field has different meaning in Tavor and Arbel, so
we are wasting mtt entries on memfree. Fix the Arbel case to match
Tavor semantics.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For some reason gcc-3.4.5 on sparc64 does:
WARNING: "____ilog2_NaN" [drivers/infiniband/hw/mthca/ib_mthca.ko] undefined!
Points to note:
(1) The asm volatile flush/flushw are just markers for viewing what comes out
in the assembly; removing them has no effect on the result.
(2) Changing almost anything else in dwh__mthca_arbel_init_srq_context() or
dwh__mthca_alloc_srq() causes the problem to go away.
The compiler command line issued by the kernel build is:
/opt/crosstool/gcc-3.4.5-glibc-2.3.6/sparc64-unknown-linux-gnu/bin/sparc64-unknown-linux-gnu-gcc -fno-strict-aliasing -fno-common -Os -m64 -mno-fpu -mcpu=ultrasparc -mcmodel=medlow -ffixed-g4 -ffixed-g5 -fcall-used-g7 -Wa,--undeclared-regs -pg -fno-omit-frame-pointer -fno-optimize-sibling-calls -fasynchronous-unwind-tables -g -c -o drivers/infiniband/hw/mthca/.tmp_mthca_srq.o drivers/infiniband/hw/mthca/mthca_srq.c
This can be reduced to this whilst still retaining the problem:
/opt/crosstool/gcc-3.4.5-glibc-2.3.6/sparc64-unknown-linux-gnu/bin/sparc64-unknown-linux-gnu-gcc -m64 -c -o drivers/infiniband/hw/mthca/mthca_srq.o drivers/infiniband/hw/mthca/mthca_srq.c -Os
Removing -Os or changing it to -O or -O0 thru -O6 gets rid of the problem.
This patch to the kernel code fixes the problem:
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When clearing the ib_ah_attr parameter in to_ib_ah_attr(), use sizeof
*ib_ah_attr instead of sizeof *path.
Pointed out by Jack Morgenstein <jackm@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
struct ib_wc currently only includes the local QP number: this matches
the IB spec, but seems mostly useless. The following patch replaces
this with the pointer to qp itself, and updates all low level drivers
and all users.
This has the following advantages:
- Ability to get a per-qp context through wc->qp->qp_context
- Existing drivers already have the qp pointer ready in poll cq, so
this change actually saves a tiny bit (extra memory read) on data path
(for ehca it would actually be expensive to find the QP pointer when
polling a CQ, but ehca does not support SRQ so we can leave wc->qp as
NULL for ehca)
- Users that need the QP number can still get it through wc->qp->qp_num
Use case:
In IPoIB connected mode code, I have a common CQ shared by multiple
QPs. To track connection usage, I need a way to get at some per-QP
context upon the completion, and I would like to avoid allocating
context object per work request just to stick a QP pointer into it.
With this code, I can just use wc->qp->qp_context.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a QP being queried is in the RESET state, don't execute the
QUERY_QP firmware command (because it will fail).
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to the Tavor and Arbel programmer's reference manuals, the
number of bytes transferred is not provided in the byte_cnt field of
the CQ entry for atomic operation completions. For atomic operations,
the number of bytes transferred is always 8 (when the status is
"success"), and this constant value should always be used by the
driver in the ib_wc entry returned, rather than using the CQE.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_table_find() will return the wrong address when the table entry
being searched for is exactly at the beginning of a sglist entry
(other than the first), because it uses >= when it should use >.
Example: assume we have 2 entries in scatterlist, 4K each, offset is
4K. The current code will return first entry + 4K when we really want
the second entry.
In particular this means mapping an FMR on a memfree HCA may end up
writing the page table into the wrong place, leading to memory
corruption and also causing the HCA to use an incorrect address
translation table.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit bed8bdfd ("IB: kmemdup() cleanup") introduced one bad conversion to
kmemdup() in mthca_alloc_fmr(), where the structure allocated and the
structure copied are not the same size. Revert this back to the original
kmalloc()/memcpy() code.
Reported-by: Dotan Barak <dotanb@mellanox.co.il>.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mthca_device_mutex() can be initialized automatically with
DEFINE_MUTEX() rather than explicitly calling mutex_init(). This
saves a bit of text and shrinks the source by a line, so we may as
well do it....
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add module parameters that enable settting some of the HCA
profile values, such as the number of QPs, CQs, etc.
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
When initializing an mthca SRQ, the log_srq_size field should be the
log of the number of SRQ WQEs, not the log of the number of bytes in
the SRQ.
This affects only mthca drivers for memfree HCAs which set the initial
srq wqe counter (in the SW2HW transition) to a non-zero value.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit b3b30f5e ("IB/mthca: Recover from catastrophic errors")
introduced some section mismatch breakage, because the error recovery
code tears down and reinitializes the device, which calls into lots of
code originally marked __devinit and __devexit from regular .text.
Fix this by getting rid of these now-incorrect section markers.
Reported by Randy Dunlap <randy.dunlap@oracle.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace open coded kmemdup() to save some screen space, and allow
inlining/not inlining to be triggered by gcc.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Several fields in an incoming MAD extended info header were passed
into the MAD_IFC firmware command at incorrect offsets (mostly off by
4 bytes). As the result, the HCA will fail to generate traps in which
this info is needed (e.g. traps which include the GRH of the incoming
packet), in violation of the IB spec.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We discovered a problem when running IPoIB applications on multiple
CPUs on an Altix system. Many messages such as:
ib_mthca 0002:01:00.0: SQ 000014 full (19941644 head, 19941707 tail, 64 max, 0 nreq)
appear in syslog, and the driver wedges up.
Apparently this is because writes to the doorbells from different CPUs
reach the device out of order. The following patch adds mmiowb() calls
after doorbell rings to ensure the doorbell writes are ordered.
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All HCAs (not just mem-free) need a spare SRQ entry, so bump srq->max
by 1 in all cases.
Noted by Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fill in "max_vl_num" (encoded according to VLCap field in the PortInfo MAD)
and "init_type_reply" values in the ib_query_port() verb.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
