commit 8ec1e0ebe26087bfc5c0394ada5feb5758014fc8
Author: Patrick McHardy <kaber@trash.net>
Date: Thu Dec 3 12:16:35 2009 +0100
ipv4: add sysctl to accept packets with local source addresses
Change fib_validate_source() to accept packets with a local source address when
the "accept_local" sysctl is set for the incoming inet device. Combined with the
previous patches, this allows to communicate between multiple local interfaces
over the wire.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define sysctl (tcp_cookie_size) to turn on and off the cookie option
default globally, instead of a compiled configuration option.
Define per socket option (TCP_COOKIE_TRANSACTIONS) for setting constant
data values, retrieving variable cookie values, and other facilities.
Move inline tcp_clear_options() unchanged from net/tcp.h to linux/tcp.h,
near its corresponding struct tcp_options_received (prior to changes).
This is a straightforward re-implementation of an earlier (year-old)
patch that no longer applies cleanly, with permission of the original
author (Adam Langley):
http://thread.gmane.org/gmane.linux.network/102586
These functions will also be used in subsequent patches that implement
additional features.
Requires:
net: TCP_MSS_DEFAULT, TCP_MSS_DESIRED
Signed-off-by: William.Allen.Simpson@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 27fed4175a (ip: fix logic of
reverse path filter sysctl) has changed the logic of rp_filter. The
document about rp_filter is out of date. Now, setting
conf/all/rp_filte with 0 can also enable source validation.
Update the document according to the commit.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Friday 02 October 2009 20:53:51 you wrote:
> This is good although I would have shortened the name.
Ah, I knew I forgot something :) Here is v4.
tavi
>From 24d96d825b9fa832b22878cc6c990d5711968734 Mon Sep 17 00:00:00 2001
From: Octavian Purdila <opurdila@ixiacom.com>
Date: Fri, 2 Oct 2009 00:51:15 +0300
Subject: [PATCH] ipv6: new sysctl for sending TLLAO with unicast NAs
Neighbor advertisements responding to unicast neighbor solicitations
did not include the target link-layer address option. This patch adds
a new sysctl option (disabled by default) which controls whether this
option should be sent even with unicast NAs.
The need for this arose because certain routers expect the TLLAO in
some situations even as a response to unicast NS packets.
Moreover, RFC 2461 recommends sending this to avoid a race condition
(section 4.4, Target link-layer address)
Signed-off-by: Cosmin Ratiu <cratiu@ixiacom.com>
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases there is not desirable to switch back to primary interface when
it's link recovers and rather stay with currently active one. We need to avoid
packetloss as much as we can in some cases. This is solved by introducing
primary_reselect option. Note that enslaved primary slave is set as current
active no matter what.
Patch modified by Jay Vosburgh as follows: fixed bug in action
after change of option setting via sysfs, revised the documentation
update, and bumped the bonding version number.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not currently possible to instruct pktgen to use one selected tx queue.
When Robert added multiqueue support in commit 45b270f8, he added
an interval (queue_map_min, queue_map_max), and his code doesnt take
into account the case of min = max, to select one tx queue exactly.
I suspect a high performance setup on a eight txqueue device wants
to use exactly eight cpus, and assign one tx queue to each sender.
This patchs makes pktgen select the right tx queue, not the first one.
Also updates Documentation to reflect Robert changes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Which is why I have always preferred sizeof(struct foo) over
sizeof(var).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new sysctl option to make IPv4 Address Scoping
configurable <draft-stewart-tsvwg-sctp-ipv4-00.txt>.
In networking environments where DNAT rules in iptables prerouting
chains convert destination IP's to link-local/private IP addresses,
SCTP connections fail to establish as the INIT chunk is dropped by the
kernel due to address scope match failure.
For example to support overlapping IP addresses (same IP address with
different vlan id) a Layer-5 application listens on link local IP's,
and there is a DNAT rule that maps the destination IP to a link local
IP. Such applications never get the SCTP INIT if the address-scoping
draft is strictly followed.
This sysctl configuration allows SCTP to function in such
unconventional networking environments.
Sysctl options:
0 - Disable IPv4 address scoping draft altogether
1 - Enable IPv4 address scoping (default, current behavior)
2 - Enable address scoping but allow IPv4 private addresses in init/init-ack
3 - Enable address scoping but allow IPv4 link local address in init/init-ack
Signed-off-by: Bhaskar Dutta <bhaskar.dutta@globallogic.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
This patch updates the sysctl documentation concerning the interpretation
of tcp_retries{1,2} and tcp_orphan_retries.
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel has used a stale email address of Andreas for a few years.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b00055aacd " [NET] core: add
RFC2863 operstate" defined new interface flag values. Its
documentation specified that these flags could be accessed from user
space via SIOCGIFFLAGS. However, this does not work because the new
flags do not fit in that ioctl's argument width.
Change the documentation to match the code's behavior. Also change
the source to explicitly show the truncation. This _should_ have no
effect on executable code, and did not with gcc 4.2.4 generating x86
code.
A new ioctl could be defined to return all interface flags to user
space. However, since this has been broken for three years with no
one complaining, there doesn't seem much need. They are still
accessible via netlink.
Reported-by: "Fredrik Arnerup" <fredrik.arnerup@edgeware.tv>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MAINTAINERS entry and a small text describing our stack interfaces,
how to hook the drivers, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'autoconf' and 'disable_ipv6' parameters to the IPv6 module.
The first controls if IPv6 addresses are autoconfigured from
prefixes received in Router Advertisements. The IPv6 loopback
(::1) and link-local addresses are still configured.
The second controls if IPv6 addresses are desired at all. No
IPv6 addresses will be added to any interfaces.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New packet socket feature that makes packet socket more efficient for
transmission.
- It reduces number of system call through a PACKET_TX_RING mechanism,
based on PACKET_RX_RING (Circular buffer allocated in kernel space
which is mmapped from user space).
- It minimizes CPU copy using fragmented SKB (almost zero copy).
Signed-off-by: Johann Baudy <johann.baudy@gnu-log.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch documents the CAN netowrk device drivers interface, removes
obsolete documentation and adds some useful links to CAN resources.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be very safe compared with full enabled, so I see
no reason why it shouldn't be done right away. As ECN can only
be negotiated if the SYN sending party is also supporting it,
somebody in the loop probably knows what he/she is doing. If
SYN does not ask for ECN, the server side SYN-ACK is identical
to what it is without ECN. Thus it's quite safe.
The chosen value is safe w.r.t to existing configs which
choose to currently set manually either 0 or 1 but
silently upgrades those who have not explicitly requested
ECN off.
Whether to just enable both sides comes up time to time but
unless that gets done now we can at least make the servers
aware of ECN already. As there are some known problems to occur
if ECN is enabled, it's currently questionable whether there's
any real gain from enabling clients as servers mostly won't
support it anyway (so we'd hit just the negative sides). After
enabling the servers and getting that deployed, the client end
enable really has some potential gain too.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't currently support antenna or rate setting, so remove
that. Also update the link -- the current one is dead and the
wiki can be kept updated easier.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a zero address hole bug in the bonding arp_ip_target list
that was causing the bond to ignore ARP replies (bugz 13006).
Instead of just setting the array entry to zero, we now
copy any additional entries down one slot, putting the
zero entry at the end. With this change we can now have
all the loops that walk the array stop when they hit a zero
since there will be no addresses after it.
Changes are based in part on code fragment provided in kernel:
bugzilla 13006:
http://bugzilla.kernel.org/show_bug.cgi?id=13006
by Steve Howard <steve@astutenetworks.com>
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- vxge driver help text file.
- No change from previous submission.
- Changes in previous submissions -
Removed the performance tuning section with instructions to disable
time stamps and change sysctl settings - Reported by Dave Miller
General clean up.
- Removed tx/rx_pause, exec_mode, tx_steering_type, rx_steering_type, gro,
intr_type, rx & tx max_indicate_pkts and exec_mode loadable parameters. The
driver default settings work well in most if not all cases. Another patch
to configure these parameters with ethtool will be released in the future -
Reported by Stephen Hemminger.
- Incorporated following fixes based on comments from Ben Hutchings
Removed references to earlier kernel versions.
Removed sections that are similar for all drivers -
Load/Unload
Identifying the adapter/interface
Boot time configuration
Removed loadable parameter -
NAPI - Napi is always enabled.
rx_steering_type & ring_blocks - The driver default settings
work well in most if not all cases. Another patch to configure
these parameters with ethtool will be released in the future.
Removed ethtool support section - No need to duplicate ethtool
docs here.
Removed Known Issue on SUSE 9 - Doesn't apply when using a
current kernel.
Removed Common Problems section - These don't apply to in-tree modules.
Removed Available Downloads section - Not sure this belongs in-tree.
Removed Copyright information - This notice doesn't belong in
the kernel.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the behavior of allowing both sysctl and addrconf_dad_failure()
to set the disable_ipv6 parameter without any bad side-effects.
If DAD fails and accept_dad > 1, we will still set disable_ipv6=1,
but then instead of allowing an RA to add an address then
immediately fail DAD, we simply don't allow the address to be
added in the first place. This also lets the user set this flag
and disable all IPv6 addresses on the interface, or on the entire
system.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation for the ixgbe driver in the kernel docs area is missing.
This adds that documentation.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add "disable" module parameter support to ipv6.ko by specifying
"disable=1" on module load. We just do the minimum of initializing
inetsw6[] so calls from other modules to inet6_register_protosw()
won't OOPs, then bail out. No IPv6 addresses or sockets can be
created as a result, and a reboot is required to enable IPv6.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This file documents the specifics of the RDS sockets API,
as well as covering some of the details of its internal
implementation.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up whitespaces while going though ip-sysctl.txt anyway.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend existing reverse path filter option to allow strict or loose
filtering. (See http://en.wikipedia.org/wiki/Reverse_path_filtering).
For compatibility with existing usage, the value 1 is chosen for strict mode
and 2 for loose mode.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instructions for time stamping outgoing packets are take from the
socket layer and later copied into the new skb.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space can request hardware and/or software time stamping.
Reporting of the result(s) via a new control message is enabled
separately for each field in the message because some of the
fields may require additional computation and thus cause overhead.
User space can tell the different kinds of time stamps apart
and choose what suits its needs.
When a TX timestamp operation is requested, the TX skb will be cloned
and the clone will be time stamped (in hardware or software) and added
to the socket error queue of the skb, if the skb has a socket
associated with it.
The actual TX timestamp will reach userspace as a RX timestamp on the
cloned packet. If timestamping is requested and no timestamping is
done in the device driver (potentially this may use hardware
timestamping), it will be done in software after the device's
start_hard_xmit routine.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds another inet device option to enable gratuitous ARP
when device is brought up or address change. This is handy for
clusters or virtualization.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This documentation is old. Add a short note to describe why aliases
are no long necessary, and remove the old contact/edit info.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It always annoyed me that the netconsole documentation didn't give me the
correct command for my distro. Update it with a command line that actually
works on my Fedora install.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds full support for local/remote Sequence Window feature, from which the
* sequence-number-validity (W) and
* acknowledgment-number-validity (W') windows
derive as specified in RFC 4340, 7.5.3.
Specifically, the following is contained in this patch:
* integrated new socket fields into dccp_sk;
* updated the update_gsr/gss routines with regard to these fields;
* updated handler code: the Sequence Window feature is located at the TX side,
so the local feature is meant if the handler-rx flag is false;
* the initialisation of `rcv_wnd' in reqsk is removed, since
- rcv_wnd is not used by the code anywhere;
- sequence number checks are not done in the LISTEN state (cf. 7.5.3);
- dccp_check_req checks the Ack number validity more rigorously;
* the `struct dccp_minisock' became empty and is now removed.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is always "an" if there is a vowel _spoken_ (not written).
So it is:
"an hour" (spoken vowel)
but
"a uniform" (spoken 'j')
Signed-off-by: Frederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This removes the use of the sysctl and the minisock variable for the Send Ack
Vector feature, as it now is handled fully dynamically via feature negotiation
(i.e. when CCID-2 is enabled, Ack Vectors are automatically enabled as per
RFC 4341, 4.).
Using a sysctl in parallel to this implementation would open the door to
crashes, since much of the code relies on tests of the boolean minisock /
sysctl variable. Thus, this patch replaces all tests of type
if (dccp_msk(sk)->dccpms_send_ack_vector)
/* ... */
with
if (dp->dccps_hc_rx_ackvec != NULL)
/* ... */
The dccps_hc_rx_ackvec is allocated by the dccp_hdlr_ackvec() when feature
negotiation concluded that Ack Vectors are to be used on the half-connection.
Otherwise, it is NULL (due to dccp_init_sock/dccp_create_openreq_child),
so that the test is a valid one.
The activation handler for Ack Vectors is called as soon as the feature
negotiation has concluded at the
* server when the Ack marking the transition RESPOND => OPEN arrives;
* client after it has sent its ACK, marking the transition REQUEST => PARTOPEN.
Adding the sequence number of the Response packet to the Ack Vector has been
removed, since
(a) connection establishment implies that the Response has been received;
(b) the CCIDs only look at packets received in the (PART)OPEN state, i.e.
this entry will always be ignored;
(c) it can not be used for anything useful - to detect loss for instance, only
packets received after the loss can serve as pseudo-dupacks.
There was a FIXME to change the error code when dccp_ackvec_add() fails.
I removed this after finding out that:
* the check whether ackno < ISN is already made earlier,
* this Response is likely the 1st packet with an Ackno that the client gets,
* so when dccp_ackvec_add() fails, the reason is likely not a packet error.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating the NDP count feature is handled automatically now:
* for CCID-2 it is disabled, since the code does not use NDP counts;
* for CCID-3 it is enabled, as NDP counts are used to determine loss lengths.
Allowing the user to change NDP values leads to unpredictable and failing
behaviour, since it is then possible to disable NDP counts even when they
are needed (e.g. in CCID-3).
This means that only those user settings are sensible that agree with the
values for Send NDP Count implied by the choice of CCID. But those settings
are already activated by the feature negotiation (CCID dependency tracking),
hence this form of support is redundant.
At startup the initialisation of the NDP count feature uses the default
value of 0, which is done implicitly by the zeroing-out of the socket when
it is allocated. If the choice of CCID or feature negotiation enables NDP
count, this will then be updated via the NDP activation handler.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX/RX CCIDs of the minisock are now redundant: similar to the Ack Vector
case, their value equals initially that of the sysctl, but at the end of
feature negotiation may be something different.
The old interface removed by this patch thus has been replaced by the newer
interface to dynamically query the currently loaded CCIDs.
Also removed are the constructors for the TX CCID and the RX CCID, since the
switch "rx <-> non-rx" is done by the handler in minisocks.c (and the handler
is the only place in the code where CCIDs are loaded).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
