cx18: Use correct Mailbox IRQ Ack values and misc IRQ handling cleanup.
The SCB field definitions for Ack IRQ's for mailboxes were inconsistent with
the bitmasks being loaded into those SCB fields and the SW2 Ack IRQ handling
logic. Renamed fields in SCB to make things consistent and did misc IRQ
handling cleanups: removing legacy ivtv dma_reg_lock, HPU IRQ flags, etc.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ok I made a patch that converts gspca kconfig file to a more standard=
one, with tabs + 2 white spaces, so that if a warning is added it still
compiles
please find it attached
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Mark CX18_CPU_DE_RELEASE_MDL as a slow API call.
Give the encoder time to complete the MDL release before destroying the
encoder internal task. This avoids an encoder lockup on the next digital
capture and error messages about buffers being returned for an inactive
encoder task handle.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Fix write retries for registers that always change - part 2.
Some registers, especially interrupt related ones, will never read
back the value just written. Modified interrupt register readback
checks to make sure the intended effect was achieved.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Final fix for when analogue only is selected
for compilation (ie, !CX88_DVB)
This tidies up previous fix and adds missing
de-alloc memory leak on fault (eg, if fe1 fails to alloc
where fe0 was allocated).
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Starts encoder not only on a read call but also on a poll command.
Signed-off-by: Frederic CAND <frederic.cand@anevia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
anysee_usb_mutex is initialized at every time the anysee device is probed.
If the second anysee device is probed while anysee_usb_mutex is locked by
the first anysee device, the mutex is broken.
This patch fixes by initialize anysee_usb_mutex statically rather
than initialize at probe time.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ivtv used tvaudio in the past and at the time tvaudio required V4L1.
Since tvaudio is no longer dependent on V4L1 and since ivtv actually
no longer uses tvaudio at all, this is no removed from Kconfig.
Without this patch ivtv won't be build if V4L1 is disabled.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a recommendation to select SND_USB_AUDIO for listing and
adds a documentation file for si470x.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Disable write retries for registers that always change - part 1.
Interrupt related registers will likely not read back the value we just wrote.
Disable retries for these registers for now to avoid accidently discarding
interrupts. More intelligent read back verification criteria are needed for
these and other registers (e.g. GPIO line registers), which will be addressed in
subsequent changes.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Apparently the author of the saa7110 driver was confused by the
number of outputs returned by DECODER_GET_CAPABILITIES. Of course a
decoder chip has no analog ouputs, but it must have at least one
digital output.
* Fix an off-by-one error when checking the input value of
DECODER_SET_INPUT.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The attached patch fix VBI support cx88 card.
I'm running a capture for hours, getting the closed caption from it[1], and
it's working perfect - the output is the same of a bttv card.
Please apply this patch as soon as possible.
[1] - using zvbi-ntsc-cc of zvbi project.
Signed-off-by: Rafael Diniz <diniz@wimobilis.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
config\tDVB_USB_CINERGY_T2 causes the make_kconfig.pl to forget to enable by default the compilation of cinergyT2 module.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There already is an report at kernel bugzilla about this issue:
http://bugzilla.kernel.org/show_bug.cgi?id=9455
When enabling extra checks for the i2c-bus of cx88 based cards by
loading i2c_algo_bit with bit_test=1 this may trigger an oops
when loading cx88_dvb.
This is caused by the extra check code that detects that the
sda-line is stuck high and thus does not register the i2c-bus.
cx88-dvb however does not check if the i2c-bus is valid and just
uses core->i2c_adap to attach dvb frontend modules.
This leads to an oops at the first call to i2c_transfer:
$ modprobe i2c_algo_bit bit_test=1
$ modprobe cx8802
cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
cx88[0]: quirk: PCIPCI_NATOMA -- set TBFX
cx88[0]: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37,autodetected], frontend(s): 1
cx88[0]: TV tuner type 4, Radio tuner type -1
cx88[0]: SDA stuck high!
cx88[0]: i2c register FAILED
input: cx88 IR (Hauppauge Nova-S-Plus as /class/input/input5
cx88[0]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:00:10.2: enabling device (0154 -> 0156)
cx88-mpeg driver manager 0000:00:10.2: PCI INT A -> Link[LNKD] -> GSI 9 (level, low) -> IRQ 9
cx88[0]/2: found at 0000:00:10.2, rev: 5, irq: 9, latency: 64, mmio: 0xfb000000
cx8802_probe() allocating 1 frontend(s)
cx88/2: cx2388x dvb driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88[0]/2: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37]
cx88[0]/2: cx2388x based DVB/ATSC card
BUG: unable to handle kernel NULL pointer dereference at 00000000
IP: [<e084d4ef>] :i2c_core:i2c_transfer+0x1f/0x80
*pde = 00000000
Modules linked in: cx88_dvb(+) cx8802 cx88xx ir_common i2c_algo_bit tveeprom videobuf_dvb btcx_risc
mga drm ipv6 fscpos eeprom nfsd exportfs stv0299 b2c2_flexcop_pci b2c2_flexcop cx24123 s5h1420 ves1x93
dvb_ttpci dvb_core saa7146_vv saa7146 videobuf_dma_sg videobuf_core videodev v4l1_compat ttpci_eeprom
lirc_serial lirc_dev usbhid rtc uhci_hcd 8139too i2c_piix4 i2c_core usbcore evdev
Pid: 4249, comm: modprobe Not tainted (2.6.27-gentoo #3)
EIP: 0060:[<e084d4ef>] EFLAGS: 00010296 CPU: 0
EIP is at i2c_transfer+0x1f/0x80 [i2c_core]
EAX: 00000000 EBX: ffffffa1 ECX: 00000002 EDX: d6c71e3c
ESI: d80cd050 EDI: d8093c00 EBP: d6c71e20 ESP: d6c71e0c
DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Impact: driver could possibly stomp on resources outside of its scope
{mchehab@redhat.com: I got two versions of the same patch (identical,
except for whitespacing). One authored by Andy Burns and another
authored by Suresh Siddha. Due to that, I'm applying the one that has
less CodingStyle errors. I'm also adding both comments and the SOB's for
both patches, since they are both interesting}
Suresh Siddha commented:
Alexey Fisher reported:
> resource map sanity check conflict: 0xcfeff800 0xcff007ff 0xcfe00000
> 0xcfefffff PCI Bus 0000:01
BAR base is located in the middle of the 4K page and the hardcoded
size argument makes the request span two pages causing the conflict.
Fix the hard coded size argument in ioremap().
Andy Burns commented:
I have already sent this patch on the linux-dvb list, but it didn't get
much attention, so re-sending direct, I hope you all don't mind.
While attempting to run mythtv in a xen domU, I encountered problems
loading the driver for my saa7134 card, with an error from ioremap().
This error was due to the driver allocating an incorrectly sized mmio
area, which was trapped by xen's permission checks, but this would go
un-noticed on a kernel without xen.
My card has a 1K sized mmio area, I've had information that other cards
have 2K areas, perhaps others have different sizes, yet the driver
always attempts to map 4K. I realise that the granularity of mapping is
the page size, which typically would be 4K, but unless the card's base
address happens to fall on a 4K boundary (mine does not) then the
base+4K will end up spanning two pages, and this is when the error
occurs under xen.
My patch uses the pci_resource_len macro to determine the size required
for the user's particular card, instead of the hardcoded 4K value. I've
tested with a couple of printk() inside ioremap() that the start address
and size do get rounded to the closest page boundary.
With this patch I am able to successfully load the saa7134 driver and
run mythtv under xen with my card, subject to correct pollirq settings
in case of shared IRQ, I am still seeing occasional DMA panics, which I
think are related to swiotlb handling by dom0/domU, usually the panic
occurs when changing mux, once tuned to a mux, 12 hour continuous
recordings are possible without errors.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andy Burns <andy@burns.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove lock_kernel() call from cafe_ccic.c
Commit d56dc61265 added lock_kernel()
calls to cafe_ccic.c. But that driver was written with proper locking
and does not need the BKL, so take it back out.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the missing compat ioctls that are needed to
operate Skype in combination with libv4l and a MJPEG only camera.
If you think it's trivial enough please submit it to -stable, too.
Signed-off-by: Gregor Jasny <gjasny@web.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by David Ellingsworth:
> I'm not sure if it matters or not, but the ibmcam driver in the
> Mauro's linux-2.6 git tree in the for_linus branch is currently
> broken.
uvd is equal to NULL during most of ibmcam_probe. Due to that, an OOPS is
generated at dev_info. This patch replaces uvd->dev->dev to dev->dev
inside this routine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reviewed-by: David Ellingsworth <david@identd.dyndns.org>
This patch add support for new device named KWorld USB FM Radio
SnapMusic Mobile 700 (FM700).
And changes few lines in comments.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update Kconfig to add missing dependency on zl10353 for dtv5100 driver.
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rather than implementing different ways leading to confusion.
This allows multiple gate_enable/disable's in the tuner_read/write
functions, thereby lesser number of I/O operations throughout,
eventually leading to better results. As a side effect demods that
detect the STOP bit for auto closing of the gate can be avoided, thereby
a very minimal gain in disabling the auto detect feature as well.
Improves readability on the device control.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This creates a self contained frontend de-allocator
for the instances where an adapter has not been
registered yet frontend de-allocation may
be required.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The multifrontend changes on cx88 assumed that all boards that use cx88-mpeg
supports DVB. This is not true. There also a few analog-only boards based on
Blackboard design that also uses cx88-mpeg. For those boards, there's no need
to allocate dvb frontends.
This patch fixes videobuf allocation for those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial fix for when analogue only is selected
for compilation (ie, !CX88_DVB)
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
inode is never used on video_ioctl2. Remove it and rename the function to
__video_ioctl2. This allows its usage directly as a callback at
fops.unlocked_ioctl.
Since we still need a callback with inode to be used with fops.ioctl,
this patch adds video_ioctl2() that is just a call to __video_ioctl2().
Also, this patch adds some comments about video_ioctl2 and __video_ioctl2
usage at v4l2-ioctl.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The inode parameter at v4l_compat_translate_ioctl() were just passed over several
places just to keep compatible with fops.ioctl. However, it weren't used anywere.
This patch gets hid of this unused parameter.
Cc: Laurent Pinchart <laurent.pinchart@skynet.be>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When using FBIOBLANK, FB_BLANK_POWERDOWN will now switch off the video output.
Since some televisions turn themselves off after a while with no signal, this
is the closest we can get to power-saving.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The kernel number of a v4l2 node (e.g. videoX, radioX or vbiX) is now
independent of the minor number. So instead of using the minor field
of the video_device struct one has to use the num field: this always
contains the kernel number of the device node.
I forgot about this when I did the v4l2 core change, so this patch
converts all drivers that use it in one go. Luckily the change is
trivial.
Cc: michael@mihu.de
Cc: mchehab@infradead.org
Cc: corbet@lwn.net
Cc: luca.risolia@studio.unibo.it
Cc: isely@pobox.com
Cc: pe1rxq@amsat.org
Cc: royale@zerezo.com
Cc: mkrufky@linuxtv.org
Cc: stoth@linuxtv.org
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When loading ivtv the TV-out of the PVR-350 will flash green since the
saa712x is activated before the MPEG decoder has been initialized.
Deactivate the saa712x until the MPEG decoder has been initialized.
Signed-off-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on an older patch from Sakari Ailus.
Cc: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Export v4l2_int_device_try_attach_all. This allows initiating the
initialisation of int if device after the drivers have been registered.
Also allow drivers to call ioctls if v4l2-int-if was compiled as
module.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Power down the s5h1411 demodulator when not in use (on the Pinnacle 801e, this
brings idle power from 123ma down to 84ma).
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we are already at the desired modulation, there is no need to reconfigure
the demod (at a tuning time cost)
Note that this change revealed that although the datasheet says the demod
starts out in VSB-8 mode, the first tuning was failing consistently unless
we went through the work of setting the registers. So add a field to denote
this case so we always do the enable_frontend call, even if the first tuning
request is for VSB-8.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If you instruct the tuner to change frequencies, it can take up to 2500ms to
get a demod lock. By performing a soft reset after the tuning call (which
is consistent with how the Pinnacle 801e Windows driver behaves), you get
a demod lock inside of 300ms
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s5h1411: Add the #define for an existing supporting I/F
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adding a serialmode function to read/and/or/write the register for safety.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This includes new bit definitions for previously unknown bits.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s5h1411: Improvements to the default registers
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add checking for frequency and printk if -1 returned.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replaced bus_info string from ISA to USB
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
(Mike Isely) This change was empirically figured out by Boris Dores
after empirically comparing against behavior in the Windows driver.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix deadlock problem in 2.6.27 caused by new USB core behavior in
response to a USB device reset request. With older kernels, the USB
device reset was "in line"; the reset simply took place and the driver
retained its association with the hardware. However now this reset
triggers a disconnect, and worse still the disconnect callback happens
in the context of the caller who asked for the device reset. This
results in an attempt by the pvrusb2 driver to recursively take a
mutex it already has, which deadlocks the driver's worker thread.
(Even if the disconnect callback were to happen on a different thread
we'd still have problems however - because while the driver should
survive and correctly disconnect / reconnect, it will then trigger
another device reset during the repeated initialization, which will
then cause another disconect, etc, forever.) The fix here is simply
to not attempt the device reset (it was of marginal value anyway).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changes to let error return codes bubble up to the user visible
error message on card initialization. A number of them were being remapped to
ENOMEM when no memory or array resource shortage existed. That hampered
diagnosis of user trouble reports.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Add __iomem address space qualifier to cx18_log_*_retries() addr
argument to clean up sparse build warnings.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On error exit, the cx18_probe() function did not use the proper entry in
cx18_cards[] with kfree() when card init failed; leaking memory.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A consolidated implementation will provide this generically through
asm/byteorder, remove direct includes to avoid breakage when the
changeover to the new implementation occurs.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (94 commits)
USB: remove err() macro from more usb drivers
USB: remove err() macro from usb misc drivers
USB: remove err() macro from usb core code
USB: remove err() macro from usb class drivers
USB: remove use of err() in drivers/usb/serial
USB: remove info() macro from usb mtd drivers
USB: remove info() macro from usb input drivers
USB: remove info() macro from usb network drivers
USB: remove info() macro from remaining usb drivers
USB: remove info() macro from usb/misc drivers
USB: remove info() macro from usb/serial drivers
USB: remove warn macro from HID core
USB: remove warn() macro from usb drivers
USB: remove warn() macro from usb net drivers
USB: remove warn() macro from usb media drivers
USB: remove warn() macro from usb input drivers
usb/fsl_qe_udc: clear data toggle on clear halt request
usb/fsl_qe_udc: fix response to get status request
fsl_usb2_udc: Fix oops on probe failure.
fsl_usb2_udc: Add a wmb before priming endpoint.
...
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove warning message during cx88-dvb compilation.
Also fixes double underline in function and struct names.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A typo was introduced during the gspca conversion, crippling the ability to control the gain on the mt9m111 sensor.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Properly iterate the allocated when freeing the urbs, this fixes a memory leak
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch marks those two functions as static:
static int videobuf_dvb_register_adapter(struct videobuf_dvb_frontends *fe,
static int videobuf_dvb_register_frontend(struct dvb_adapter *adapter,
Since MFE patches changed their calls by videobuf_dvb_register_bus.
To avoid having to declare the prototypes, the patch moves
videobuf_dvb_register_bus() to be after the declaration of the above functions
used there.
Cc: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| drivers/media/dvb/frontends/cx24116.c:573: warning: passing argument 3 of 'cx24116_writeregN' discards qualifiers from pointer target type
Make the `data' input pointer parameter of cx24116_writeregN() const to
kill the warning.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MFE: videobuf-dvb.c checkpatch cleanup as part of MFE merge
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jose reported:
I am using a Avermedia Volar X with af9015 driver(DVB-T).
The first time you use the card, first call reconfigure with MXL_QAM,
and when tune DVB-T it calls reconfigure with MXL_DVBT. But if you close
the frontend and open again, it calls reconfigure with MXL_QAM, but not
call reconfigure with MXL_DVBT because state->current_mode don't change
(is MXL_DVBT).
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To optimise data storage even further one other redundant
var has been removed.
This also removes a redundant assignment.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Christophe divulged the following:
"Since 8PSK (and higher mod) signals are very likely to have pilot symbols,
pilot_auto should start with pilot_on for 8PSK.
And since QPSK signals are unlikely to have pilot, pilot_auto should start
with pilot_off for QPSK.
Without the patch:
QPSK tuning delay: ~100ms
8PSK tuning delay: ~900ms
with patch:
QPSK tuning delay: ~100ms
8PSK tuning delay: ~100ms
"
This patch does as Cristophe asks. In emulated auto-pilot we
choose pilot-on for tuning PSK_8 and pilot-off for
tuning QPSK.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds I2S-ADC tvaudio mode as a formal method of audio
delivery.
This fixes one bug and adds fm audio via I2S-ADC on cards
that support it.
The bug occured before when I2S-ADC mode was initiated on
composite/s-video open but was then reset within 500ms
by the audio thread which used any previous audio tuning
details.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This tuner was already supported by proxy as an FMD1216ME, however,
the MEX uses a different FM Radio IF so this addition is now required.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds audio routing for the hvr-1300/3000/4000 cards
enabling FM audio for the I2S ADC method of the cx88.
At this time only the HVR-4000 has been tested. It
is assumed the HVR-3000/1300 are the same.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes attachment failure where we now unwind
attachment and skip non-attached nodes where
necessary so we can survive a fault situation
correctly.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To optimise data storage redundant vars are removed.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When moving from one frontend to another
an application could spawn multiple threads opening
the same new frontend and in some circumstances all of
these could become delayed waiting for the previous
frontend readers or previous frontend writer thread to
complete.
In this scenario the first thread will succeed on open
to bring the new frontend online but any others will return
EBUSY. This is a fault. If the first succeeds and all others
are on the same frontend then they should succeed also.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of users have complained that their syslog often shows this
messages but it doesn't impact performance. I'm changing this to a debug
message, so developers will still see the message during testing and
users will no longer be bothered by this.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add autodetection support for a new revision of the Hauppauge HVR950Q (2040:721e)
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch improves the buffer handling in the sh_mobile_ceu driver.
Instead of marking all queued buffers as VIDEOBUF_ACTIVE the code now
marks queued-but-not-active buffers as VIDEOBUF_QUEUED and buffers
involved in dma as VIDEOBUF_ACTIVE. The code is also updated with
code to cancel active buffers, thanks to Morimoto-san.
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend the sh_mobile_ceu driver to enable byte swap. This way bytes
are stored in memory in incoming byte order.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switching sensors on and off is now done by sensor drivers themselves,
typically using platform-provided hooks. Update soc_camera_platform.c to
do the same. Also remove a refundant struct soc_camera_platform_info
definition from soc_camera_platform.c.
Tested-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds RGB555 pixel format support to the vivi driver. Both
little endian and big endian versions are added. The driver follows
the RGB pixel format described in Table 2-2 of the V4L2 API spec,
_not_ the older BGR interpretation described in Table 2-1.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds RGB565 pixel format support to the vivi driver. Both
little endian and big endian versions are added. The driver follows
the RGB pixel format described in Table 2-2 of the V4L2 API spec,
_not_ the older BGR interpretation described in Table 2-1.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch simply adds UYVY pixel format support to the vivi driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch contains the ground work to add support for multiple
pixel formats to vivi.c
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch improves the color space conversion code in vivi.c to
directly draw with precalculated YUV values as palette instead of
drawing with YUV that is calculated from RGB for every two pixels.
This way we eliminate the need for 9 multiplications every two pixels.
A side effect of this patch is that the time counter is changed from
green text on black background to white text on black background.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no point in logging two messages for the same error.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx23885 frontend allocation code needs to exist in the higher function,
and it also needs to ensure videobug is also correctly initialised
on a per frontend basis. This code uses the previous num_frontends
patch to safely init each future MFE frontend on a single tsport as
as safely as possible - given that we don't have any of those boards.
Again, better to add all of this safety code now, while the MFE patch
set is fresh in everyone mind, than to try and add it 12-24 months from
now, when the subject is cold.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows some cardcoded functions to be more flexible, and paves
the way for any future cards that may have MFE support. Better to add it
now when the MFE patches is fresh in peoples mind, rather than 12 months
from now when new cards appear.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bug: the tree generated an oops when the cx23885 was laoded. This avoids
the oops by ensuring the mutex is correctly initialised before it's used.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This add initial configuration for radio support on the
hvr-3000/4000. FM radio doesn't work as yet without
further patches (to come), but this prepares for
that.
Experimental radio support shows that it works
when combined with additional audio routing
work for cards with an FMD1216ME analogue
frontend, but not the MEX variant (more later).
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds audio routing on the hvr-3000/4000
This is a preliminary patch for later routing
requirements.
This adds line-in support on the 2 cards mentioned.
It is also apparent that there is an initial open
fault for line-in when opening composite/s-video.
This will be fixed later.
It was also noticed that the bit-field for audio
routing which was 2 bits needs an increase as
the WM8775 for example, allows a value 4 bits
wide for it's audio mux.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This add frontend R/W mutual exclusion.
Prior to this point in time it was possible to open both
frontends simultaneously which an MFE card cannot support.
In order to stop this, a delayed open is performed which
has the following function:
- Return EBUSY after a configurable amount of time
if a frontend is unavailable due to the other being
in use.
- Only allow opening of a frontend if the kernel thread
of the other has stopped.
This solution was chosen to allow switching between
frontends to work as seamlessly as possible. When both
frontends are actually opened simultaneously then one
will only open, but if quick switching is performed
between one of many then the new open will succeed in
a clean fashion rather than interrupting a kernel
thread.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx22702 is now always reset on module load. Prior to
this the cx22702 was not found on i2c scan without a
full reset.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds a configurable (one per card) gate control option
for multi-frontend. Prior to this point gate control was
assumed to be on the primary frontend, this is a fault
when the gate to the analogue section is on the secondary
which is the default for both the HVR-3000 and HVR-4000
in MFE.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When using MFE on a setup with both and HVR-3000 and ASUS P7131
card it was noticed that frontend allocation for saa7134
adapters was missing. This patch adds that allocation for
both saa7134 and cx23885 adapters.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of reference to videobuf_dvb_get_frontend used an invalid
index. This has been fixed.
The section for the HVR3000 in advise_acquire was redundant as
the same logic is used on the HVR4000. This has been removed
and both cards now use the same function.
A number of small errors and whitespace errors are also fixed.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A detailed description from the original patches 2 years ago:
"The WinTV-HVR3000 has a single transport bus which is shared between
a DVB-T and DVB-S modulator. These patches build on the bus acquisition
cx88 work from a few weeks ago to add support for this.
So to applications the HVR3000 looks like this:
/dev/dvb/adapter0/fe0 (cx24123 DVB-S demod)
/dev/dvb/adapter0/fe1 (cx22702 DVB-T demod)
Additional boards continue as before, eg:
/dev/dvb/adapter1/fe0 (lgdt3302 ATSC demod)
The basic change is removing the single instance of the videobuf_dvb in
cx8802_dev and saa7134_dev(?) and replacing it with a list and some
supporting functions.
*NOTE* This branch was taken before v4l-dvb was closed for 2.6.19 so
two or three current cx88 patches appear to be reversed by this tree,
this will be cleaned up in the near future. The patches missing change
the mutex handing to core->lock, fix an enumeration problem."
It should be recognised that a number of people have been maintaining
this patchset. Significant levels of Kudos to everyone one involved,
including but not limited to:
Darron Broad
Fabio M. Di Nitto
Carlo Scarfoglio
Hans Werner
Without the work of these people, and countless others, my two year old
patches would of died on the Mercurial linuxtv.org vine a long time
ago.
TODO: Revise these patches a little further so that the need for
demux1 and dvr0 is optional, not mandatory on the HVR3000.
HISTORY (darron):
This is the last update to MFE prepared by Hans which is based
upon the `scratchpad' diff created by Carlo.
All MFE work prior to that point must be attributed to Fabio
who ported and maintained Steve's original patch up to that
time.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the unnecessary get/set input/audio functions.
The reason is, that the V4L2 specification says, that if input or audio
cannot be switched anyway, the functions doesn't need to be implemented.
I've tested the new driver with all current radio programs in
Debian/testing and found no problems with that.
In my opinion, the driver is much cleaner by removing these unnecessary
functions.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch corrects the behavior of mono/stereo indication and
selection.
These functions now work conform to what's defined in the V4L2
specification.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2 specification says, when to check and when to return
tuner->type as constant value.
This patch corrects exactly this behavior, so that it is now conform to
the V4L2 specification.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch changes the handling of unsupported base controls.
In the former version, specific unsupported base controls were listed in
the queryctrl table and were flagged as disabled controls. This was done
for all base controls used by the applications.
The patch now removes the specific base controls and instead lets
queryctrl automatically return unsupported base controls flagged as
disabled.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch improves support for multiple radio devices.
In previous versions all region relevant settings were derived from one
module parameter. As in future versions, the region and other
configuration should be configurable per device from the user space,
this patch already retrieves all relevant information from the actual
device specific settings.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch mainly adds correct module_param access rights. Also there
are a lot of small coding style enhancements and some corrections of the
variable references in module_param.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Convert to use v4l2-i2c-drv-legacy.h to be able to handle the new i2c API
- Cleanups
- Use v4l_dbg/v4l_info to have uniform kernel messages
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Convert to use v4l2-i2c-drv-legacy.h to be able to handle the new i2c API
- Cleanups
- Use v4l_dbg/v4l_info to have uniform kernel messages
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Convert to use v4l2-i2c-drv-legacy.h to be able to handle the new i2c API
- Cleanups
- Use v4l_dbg/v4l_info to have uniform kernel messages
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Convert to use v4l2-i2c-drv-legacy.h to be able to handle the new i2c API
- Cleanups
- Use v4l_dbg/v4l_info to have uniform kernel messages
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Convert to use v4l2-i2c-drv-legacy.h to be able to handle the new i2c API
- Cleanups
- Use v4l_dbg/v4l_info to have uniform kernel messages
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Convert to use v4l2-i2c-drv-legacy.h to be able to handle the new i2c API
- Cleanups
- Use v4l_dbg/v4l_info to have uniform kernel messages
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Convert to use v4l2-i2c-drv-legacy.h to be able to handle the new i2c API
- Cleanups
- Use v4l_dbg/v4l_info to have uniform kernel messages
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Convert to use v4l2-i2c-drv-legacy.h to be able to handle the new i2c API
- Cleanups
- Use v4l_dbg/v4l_info to have uniform kernel messages
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Convert to use v4l2-i2c-drv-legacy.h to be able to handle the new i2c API
- Cleanups
- Use v4l_dbg/v4l_info to have uniform kernel messages
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Convert to use v4l2-i2c-drv-legacy.h to be able to handle the new i2c API
- Cleanups
- Use v4l_dbg/v4l_info to have uniform kernel messages
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Convert to use v4l2-i2c-drv-legacy.h to be able to handle the new i2c API
- Cleanups
- Use v4l_dbg/v4l_info to have uniform kernel messages
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The adapter class of the zoran driver was never set. However, converting
i2c drivers used by zoran to the new i2c API requires this field to be
correct.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch prevents stk-webcam from updating usb device information
once the camera has been removed. This prevents a crash that would
otherwise occur if the camera is disconnected while it is still in
use.
Signed-off-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch:
1) removes the unnecessary kref.h include file
2) removes unnecessary pointer validation from read and poll routines.
(Neither poll nor read may be called unless a call to open succeeds. A
successful call to open will always set the file private_data pointer.
Verifying that it is not null is therefore unnecessary. The associated
release and mmap calls currently ignore this check.)
3) adds a space to syslog output.
4) removes an unused function prototype.
Signed-off-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ian Armstrong pointed out to me that it is perfectly valid to have a
576 lines YUV video with NTSC output in this particular case. In fact,
without this the X driver for ivtv does not function properly.
Reverted my earlier change that restrictred the height to 480 for NTSC
and add the comments provided by Ian to explain what is happening here.
Thanks-to: Ian Armstrong <ian@iarmst.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modifies behaviour of a failed dma write() operation for the yuv device.
If the dma transfer for the yuv device fails, the write() operation will now
exit immediately.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
Straight forward conversions to CONFIG_MODULE; many drivers
include <linux/kmod.h> conditionally and then don't have any
other conditional code so remove it from those.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: video4linux-list@redhat.com
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-ppp@vger.kernel.org
Cc: dm-devel@redhat.com
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (313 commits)
V4L/DVB (9186): Added support for Prof 7300 DVB-S/S2 cards
V4L/DVB (9185): S2API: Ensure we have a reasonable ROLLOFF default
V4L/DVB (9184): cx24116: Change the default SNR units back to percentage by default.
V4L/DVB (9183): S2API: Return error of the caller provides 0 commands.
V4L/DVB (9182): S2API: Added support for DTV_HIERARCHY
V4L/DVB (9181): S2API: Add support fot DTV_GUARD_INTERVAL and DTV_TRANSMISSION_MODE
V4L/DVB (9180): S2API: Added support for DTV_CODE_RATE_HP/LP
V4L/DVB (9179): S2API: frontend.h cleanup
V4L/DVB (9178): cx24116: Add module parameter to return SNR as ESNO.
V4L/DVB (9177): S2API: Change _8PSK / _16APSK to PSK_8 and APSK_16
V4L/DVB (9176): Add support for DvbWorld USB cards with STV0288 demodulator.
V4L/DVB (9175): Remove NULL pointer in stb6000 driver.
V4L/DVB (9174): Allow custom inittab for ST STV0288 demodulator.
V4L/DVB (9173): S2API: Remove the hardcoded command limit during validation
V4L/DVB (9172): S2API: Bugfix related to DVB-S / DVB-S2 tuning for the legacy API.
V4L/DVB (9171): S2API: Stop an OOPS if illegal commands are dumped in S2API.
V4L/DVB (9170): cx24116: Sanity checking to data input via S2API to the cx24116 demod.
V4L/DVB (9169): uvcvideo: Support two new Bison Electronics webcams.
V4L/DVB (9168): Add support for MSI TV@nywhere Plus remote
V4L/DVB: v4l2-dev: remove duplicated #include
...
Added support for Prof 7300 DVB-S/S2 card. The card
based on cx24116 demodulator.
Signed-off-by: Oleg Roitburd <oroitburd@gmail.com>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
[mchehab@redhat.com: fixed CARDLIST.cx88 entry]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx24116: Change the default SNR units back to percentage by default.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A user tuning DVB-T via the S2API reports that this was not implemented,
and his tuning was failing.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuning DVB-T via the S2API was failing, missing some essential items.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reports from users that using the new API for tuning DTV was failing,
and the cache was missing some essential items.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I've retained the older percentage code after discussing this with
Darron Broad, but made the ESNO option default.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
... and cleanup any drivers using them.
I've also removed NBC_QPSK and modified the cx24116 driver to check
the delivery_type also, removing some excess namespace baggage.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for DvbWorld USB cards with STV0288 demodulator.
Those cards use Earda EDS-1547 tuner.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove NULL pointer in stb6000 driver,
as it raises error for DvbWorld USB card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow custom inittab for ST STV0288 demodulator,
as it is needed for DvbWorld USB card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This means that when developers add new commands then they'll be see
the DTV_MAX_COMMAND define and will be more likely to modify it, without
having to modify the command validation code.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes switching from S2API to legacy where legacy params given to S2API
aware demods are cached ones and not those implied in the legacy API.
It was found (on an S2API aware demod at least) that after using
an S2API aware application and then switching to a legacy application
that prior S2API params were in effect were legacy has only
implied values. This fixes this.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Quick fix to stop an OOPS if illegal commands are dumped in S2API.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add some sanity checking to data input via S2API to the cx24116 demod.
This patch is valid for both s2-mfe and s2.
It was found when testing KAFFEINE with S2API support that invalid
modulation modes amongst other parameters were being delivered to
the demod. In order to debug this sanity checking has been added.
An example session would involve kaffeine setting QAM_AUTO when
querying DVB-T, then later when trying to tune to DVB-S this
cached value would be presented in error.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The IR controller has a couple quirks. It won't respond until some other
device on the bus is probed. To work around that, probe 0x50 first.
Then, since it won't respond to a zero-byte read, probe with a one-byte
read.
Signed-off-by: Brian Rogers <brian_rogers@comcast.net>
[mchehab.redhat.com: Fix merge conflicts and remove an unused var]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modified yuv register update handling to remove a potential race condition
which could occur with the first video frame.
Also removed a forced yuv position update, since changing the source video
dimensions or interlace settings doesn't affect the frame already being
displayed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the framebuffer format was queried via VIDIOC_G_FBUF,
V4L2_FBUF_FLAG_OVERLAY would only be correctly returned for certain screen
depths.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The service_set field was used in saa7115 and cx25840 to determine
whether raw or sliced VBI was desired. This is incorrect since it is
perfectly valid to select sliced VBI with a service_set of 0.
Instead these drivers should checked on VIDIOC_S_FMT whether the type
field matches the raw or sliced VBI type.
Updated ivtv accordingly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the vidioc_enum_fmt_vbi_cap ops: it was scheduled for removal in
2.6.28 since the v4l2 specification says that V4L2_BUF_TYPE_VBI_CAPTURE should
not support VIDIOC_ENUM_FMT. It's also pretty pointless.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Suggested by Martin Dauskardt. This is conform what the other drivers do.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In dvb_init(),
case EM2880_BOARD_TERRATEC_HYBRID_XS:
case EM2880_BOARD_KWORLD_DVB_310U:
can be put in the same case than EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900
since they do the same thing.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds printk messages, adds checking if frequency is set,
adds return -EINVAL in right places in zoltrix-radio.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Add USB ID for MSI DIGIVOX mini III (1462:8807)
Signed-off-by: Herbert Graeber <herbert@graeber-clan.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- enable Maxlinear mxl5005s tuner RSSI
Thaks to Jose Alberto for finding this setting.
Thanks-to: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- fix wrong GPIO that causes 2nd FE not to work ater warmboot
Thanks to Andrew Williams <andrew.williams@joratech.com> for reporting this.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prevent the zoran driver sources from cluttering the video directory.
This changeset only moves the drivers and it does not fix any of the
checkpatch warnings/errors to keep the changeset clean.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Well, one thing you encouraged me to do was re-test some of my cards
which contained the xc3028-zarlink combo.
Which led me to test a Dvico FusionHDTV Pro.
Almost a year ago, Chris Pascoe did a patch for this which can be found
at his ~pascoe/xc-test at Linuxtv.
This worked very well, however that was using his version of firmware.
Alas, someone attempted to use this and patch v4l-dvb, and messed it up.
So I've fixed it.
I enclose the patch against today's tree (containing your latest
tuner-xc2028.c patch).
The card now works very well, well with DVB-T anyway.
Signed-off-by: Tim Farrington <timf@iinet.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l core creates four different video devices (video, vbi, radio, vtx)
and each has its own range of minor numbers. However, modern devices keep
increasing the number of devices that they need so a maximum of 64 video
devices will not be enough in the future. In addition this scheme makes
it very hard to add new device types.
This patch disconnects the kernel number allocation (e.g. video0, video1,
etc.) from the actual minor number (just pick the first free minor).
This allows for much more flexibility in the future. However, it does
require the use of udev. For those who cannot use udev a new CONFIG option
was created that changes the allocation scheme back to the old behavior.
Thanks to Greg KH for suggesting this approach during the 2008 LPC.
In addition, several bugs were fixed in the ivtv and cx18 drivers: these
drivers try to allocate specific kernel numbers but that scheme contained
a bug which caused what should have been e.g. video17 to appear as e.g.
video2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Fix warning message for DMA done notification for inactive stream. The
warning message would always gripe that the radio stream was to blame, which
was misleading and wrong (/dev/radioN nodes never transfer data).
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
