If a bridge with vlan_filtering enabled receives frames with stacked
vlan tags, i.e., they have two vlan tags, br_vlan_untag() strips not
only the outer tag but also the inner tag.
br_vlan_untag() is called only from br_handle_vlan(), and in this case,
it is enough to set skb->vlan_tci to 0 here, because vlan_tci has already
been set before calling br_handle_vlan().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge vlan code (br_vlan_get_tag()) assumes that all frames have vlan_tci
if they are tagged, but if vlan tx offload is manually disabled on bridge
device and frames are sent from vlan device on the bridge device, the tags
are embedded in skb->data and they break this assumption.
Extract embedded vlan tags and move them to vlan_tci at ingress.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this check someone could easily create a denial of service
by injecting multicast-specific queries to enable the bridge
snooping part if no real querier issuing periodic general queries
is present on the link which would result in the bridge wrongly
shutting down ports for multicast traffic as the bridge did not learn
about these listeners.
With this patch the snooping code is enabled upon receiving valid,
general queries only.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
General IGMP and MLD queries are supposed to have the multicast
link-local all-nodes address as their destination according to RFC2236
section 9, RFC3376 section 4.1.12/9.1, RFC2710 section 8 and RFC3810
section 5.1.15.
Without this check, such malformed IGMP/MLD queries can result in a
denial of service: The queries are ignored by most IGMP/MLD listeners
therefore they will not respond with an IGMP/MLD report. However,
without this patch these malformed MLD queries would enable the
snooping part in the bridge code, potentially shutting down the
according ports towards these hosts for multicast traffic as the
bridge did not learn about these listeners.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
MLD queries are supposed to have an IPv6 link-local source address
according to RFC2710, section 4 and RFC3810, section 5.1.14. This patch
adds a sanity check to ignore such broken MLD queries.
Without this check, such malformed MLD queries can result in a
denial of service: The queries are ignored by any MLD listener
therefore they will not respond with an MLD report. However,
without this patch these malformed MLD queries would enable the
snooping part in the bridge code, potentially shutting down the
according ports towards these hosts for multicast traffic as the
bridge did not learn about these listeners.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_fdb_change_mac_address() calls fdb_insert()/fdb_delete() without
br->hash_lock.
These hash list updates are racy with br_fdb_update()/br_fdb_cleanup().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlan codes unconditionally delete local fdb entries.
We should consider the possibility that other ports have the same
address and vlan.
Example of problematic case:
ip link set eth0 address 12:34:56:78:90:ab
ip link set eth1 address aa:bb:cc:dd:ee:ff
brctl addif br0 eth0
brctl addif br0 eth1 # br0 will have mac address 12:34:56:78:90:ab
bridge vlan add dev eth0 vid 10
bridge vlan add dev eth1 vid 10
bridge vlan add dev br0 vid 10 self
We will have fdb entry such that f->dst == eth0, f->vlan_id == 10 and
f->addr == 12:34:56:78:90:ab at this time.
Next, delete eth0 vlan 10.
bridge vlan del dev eth0 vid 10
In this case, we still need the entry for br0, but it will be deleted.
Note that br0 needs the entry even though its mac address is not set
manually. To delete the entry with proper condition checking,
fdb_delete_local() is suitable to use.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_fdb_delete_by_port() doesn't care about vlan and mac address of the
bridge device.
As the check is almost the same as mac address changing, slightly modify
fdb_delete_local() and use it.
Note that we can always set added_by_user to 0 in fdb_delete_local() because
- br_fdb_delete_by_port() calls fdb_delete_local() for local entries
regardless of its added_by_user. In this case, we have to check if another
port has the same address and vlan, and if found, we have to create the
entry (by changing dst). This is kernel-added entry, not user-added.
- br_fdb_changeaddr() doesn't call fdb_delete_local() for user-added entry.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_fdb_change_mac_address() doesn't check if the local entry has the
same address as any of bridge ports.
Although I'm not sure when it is beneficial, current implementation allow
the bridge device to receive any mac address of its ports.
To preserve this behavior, we have to check if the mac address of the
entry being deleted is identical to that of any port.
As this check is almost the same as that in br_fdb_changeaddr(), create
a common function fdb_delete_local() and call it from
br_fdb_changeadddr() and br_fdb_change_mac_address().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should take into account the followings when deleting a local fdb
entry.
- nbp_vlan_find() can be used only when vid != 0 to check if an entry is
deletable, because a fdb entry with vid 0 can exist at any time while
nbp_vlan_find() always return false with vid 0.
Example of problematic case:
ip link set eth0 address 12:34:56:78:90:ab
ip link set eth1 address 12:34:56:78:90:ab
brctl addif br0 eth0
brctl addif br0 eth1
ip link set eth0 address aa:bb:cc:dd:ee:ff
Then, the fdb entry 12:34:56:78:90:ab will be deleted even though the
bridge port eth1 still has that address.
- The port to which the bridge device is attached might needs a local entry
if its mac address is set manually.
Example of problematic case:
ip link set eth0 address 12:34:56:78:90:ab
brctl addif br0 eth0
ip link set br0 address 12:34:56:78:90:ab
ip link set eth0 address aa:bb:cc:dd:ee:ff
Then, the fdb still must have the entry 12:34:56:78:90:ab, but it will be
deleted.
We can use br->dev->addr_assign_type to check if the address is manually
set or not, but I propose another approach.
Since we delete and insert local entries whenever changing mac address
of the bridge device, we can change dst of the entry to NULL regardless of
addr_assign_type when deleting an entry associated with a certain port,
and if it is found to be unnecessary later, then delete it.
That is, if changing mac address of a port, the entry might be changed
to its dst being NULL first, but is eventually deleted when recalculating
and changing bridge id.
This approach is especially useful when we want to share the code with
deleting vlan in which the bridge device might want such an entry regardless
of addr_assign_type, and makes things easy because we don't have to consider
if mac address of the bridge device will be changed or not at the time we
delete a local entry of a port, which means fdb code will not be bothered
even if the bridge id calculating logic is changed in the future.
Also, this change reduces inconsistent state, where frames whose dst is the
mac address of the bridge, can't reach the bridge because of premature fdb
entry deletion. This change reduces the possibility that the bridge device
replies unreachable mac address to arp requests, which could occur during
the short window between calling del_nbp() and br_stp_recalculate_bridge_id()
in br_del_if(). This will effective after br_fdb_delete_by_port() starts to
use the same code by following patch.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlan code may need fdb change when changing mac address of bridge device
even if it is caused by the mac address changing of a bridge port.
Example configuration:
ip link set eth0 address 12:34:56:78:90:ab
ip link set eth1 address aa:bb:cc:dd:ee:ff
brctl addif br0 eth0
brctl addif br0 eth1 # br0 will have mac address 12:34:56:78:90:ab
bridge vlan add dev br0 vid 10 self
bridge vlan add dev eth0 vid 10
We will have fdb entry such that f->dst == NULL, f->vlan_id == 10 and
f->addr == 12:34:56:78:90:ab at this time.
Next, change the mac address of eth0 to greater value.
ip link set eth0 address ee:ff:12:34:56:78
Then, mac address of br0 will be recalculated and set to aa:bb:cc:dd:ee:ff.
However, an entry aa:bb:cc:dd:ee:ff will not be created and we will be not
able to communicate using br0 on vlan 10.
Address this issue by deleting and adding local entries whenever
changing the mac address of the bridge device.
If there already exists an entry that has the same address, for example,
in case that br_fdb_changeaddr() has already inserted it,
br_fdb_change_mac_address() will simply fail to insert it and no
duplicated entry will be made, as it was.
This approach also needs br_add_if() to call br_fdb_insert() before
br_stp_recalculate_bridge_id() so that we don't create an entry whose
dst == NULL in this function to preserve previous behavior.
Note that this is a slight change in behavior where the bridge device can
receive the traffic to the new address before calling
br_stp_recalculate_bridge_id() in br_add_if().
However, it is not a problem because we have already the address on the
new port and such a way to insert new one before recalculating bridge id
is taken in br_device_event() as well.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have been always failed to delete the old entry at
br_fdb_change_mac_address() because br_set_mac_address() updates
dev->dev_addr before calling br_fdb_change_mac_address() and
br_fdb_change_mac_address() uses dev->dev_addr to find the old entry.
That update of dev_addr is completely unnecessary because the same work
is done in br_stp_change_bridge_id() which is called right away after
calling br_fdb_change_mac_address().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit bc9a25d21e ("bridge: Add vlan support for local fdb entries"),
br_fdb_changeaddr() has inserted a new local fdb entry only if it can
find old one. But if we have two ports where they have the same address
or user has deleted a local entry, there will be no entry for one of the
ports.
Example of problematic case:
ip link set eth0 address aa:bb:cc:dd:ee:ff
ip link set eth1 address aa:bb:cc:dd:ee:ff
brctl addif br0 eth0
brctl addif br0 eth1 # eth1 will not have a local entry due to dup.
ip link set eth1 address 12:34:56:78:90:ab
Then, the new entry for the address 12:34:56:78:90:ab will not be
created, and the bridge device will not be able to communicate.
Insert new entries regardless of whether we can find old entries or not.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_fdb_changeaddr() assumes that there is at most one local entry per port
per vlan. It used to be true, but since commit 36fd2b63e3 ("bridge: allow
creating/deleting fdb entries via netlink"), it has not been so.
Therefore, the function might fail to search a correct previous address
to be deleted and delete an arbitrary local entry if user has added local
entries manually.
Example of problematic case:
ip link set eth0 address ee:ff:12:34:56:78
brctl addif br0 eth0
bridge fdb add 12:34:56:78:90:ab dev eth0 master
ip link set eth0 address aa:bb:cc:dd:ee:ff
Then, the address 12:34:56:78:90:ab might be deleted instead of
ee:ff:12:34:56:78, the original mac address of eth0.
Address this issue by introducing a new flag, added_by_user, to struct
net_bridge_fdb_entry.
Note that br_fdb_delete_by_port() has to set added_by_user to 0 in cases
like:
ip link set eth0 address 12:34:56:78:90:ab
ip link set eth1 address aa:bb:cc:dd:ee:ff
brctl addif br0 eth0
bridge fdb add aa:bb:cc:dd:ee:ff dev eth0 master
brctl addif br0 eth1
brctl delif br0 eth0
In this case, kernel should delete the user-added entry aa:bb:cc:dd:ee:ff,
but it also should have been added by "brctl addif br0 eth1" originally,
so we don't delete it and treat it a new kernel-created entry.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 93d8bf9fb8 ("bridge: cleanup netpoll code") introduced
a check in br_netpoll_enable(), but this check is incorrect for
br_netpoll_setup(). This patch moves the code after the check
into __br_netpoll_enable() and calls it in br_netpoll_setup().
For br_add_if(), the check is still needed.
Fixes: 93d8bf9fb8 ("bridge: cleanup netpoll code")
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_handle_vlan() pushes HW accelerated vlan tag into skbuff when outgoing
port is the bridge device.
This is unnecessary because __netif_receive_skb_core() can handle skbs
with HW accelerated vlan tag. In current implementation,
__netif_receive_skb_core() needs to extract the vlan tag embedded in skb
data. This could cause low network performance especially when receiving
frames at a high frame rate on the bridge device.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And it can become static.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't encode argument types into function names and since besides
nft_do_chain() there are only AF-specific versions, there is no risk
of confusion.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Minor nf_chain_type cleanups:
- reorder struct to plug a hoe
- rename struct module member to "owner" for consistency
- rename nf_hookfn array to "hooks" for consistency
- reorder initializers for better readability
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In some cases we neither take a reference to the AF info nor to the
chain type, allowing the module to be unloaded while in use.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add support to register chains to multiple hooks for different address
families for mixed IPv4/IPv6 tables.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Currently the AF-specific hook functions override the chain-type specific
hook functions. That doesn't make too much sense since the chain types
are a special case of the AF-specific hooks.
Make the AF-specific hook functions the default and make the optional
chain type hooks override them.
As a side effect, the necessary code restructuring reduces the code size,
f.i. in case of nf_tables_ipv4.o:
nf_tables_ipv4_init_net | -24
nft_do_chain_ipv4 | -113
2 functions changed, 137 bytes removed, diff: -137
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEVICE_ATTR_RO/RW macros to simplify bridge sysfs attribute definitions.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_multicast_set_hash_max() is called from process context in
net/bridge/br_sysfs_br.c by the sysfs store_hash_max() function.
br_multicast_set_hash_max() calls spin_lock(&br->multicast_lock),
which can deadlock the CPU if a softirq that also tries to take the
same lock interrupts br_multicast_set_hash_max() while the lock is
held . This can happen quite easily when any of the bridge multicast
timers expire, which try to take the same lock.
The fix here is to use spin_lock_bh(), preventing other softirqs from
executing on this CPU.
Steps to reproduce:
1. Create a bridge with several interfaces (I used 4).
2. Set the "multicast query interval" to a low number, like 2.
3. Enable the bridge as a multicast querier.
4. Repeatedly set the bridge hash_max parameter via sysfs.
# brctl addbr br0
# brctl addif br0 eth1 eth2 eth3 eth4
# brctl setmcqi br0 2
# brctl setmcquerier br0 1
# while true ; do echo 4096 > /sys/class/net/br0/bridge/hash_max; done
Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are same, so unify them as one, pcpu_sw_netstats.
Define pcpu_sw_netstat in netdevice.h, remove pcpu_tstats
from if_tunnel and remove br_cpu_netstats from br_private.h
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function __rtnl_af_register is never called outside this
code, and the return value is always 0.
Signed-off-by: David S. Miller <davem@davemloft.net>
That open brace { should be on the previous line.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spaces required before the open parenthesis '(', before the open
brace '{', after that ',' and around that '?/:'.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return is not a function, parentheses are not required.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because err is always negative, remove unnecessary condition
judgment.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix spelling errors in bridge driver.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various spelling fixes in networking stack
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
br_stp_rcv() is reached by non-rx_handler path. That means there is no
guarantee that dev is bridge port and therefore simple NULL check of
->rx_handler_data is not enough. There is need to check if dev is really
bridge port and since only rcu read lock is held here, do it by checking
->rx_handler pointer.
Note that synchronize_net() in netdev_rx_handler_unregister() ensures
this approach as valid.
Introduced originally by:
commit f350a0a873
"bridge: use rx_handler_data pointer to store net_bridge_port pointer"
Fixed but not in the best way by:
commit b5ed54e94d
"bridge: fix RCU races with bridge port"
Reintroduced by:
commit 716ec052d2
"bridge: fix NULL pointer deref of br_port_get_rcu"
Please apply to stable trees as well. Thanks.
RH bugzilla reference: https://bugzilla.redhat.com/show_bug.cgi?id=1025770
Reported-by: Laine Stump <laine@redhat.com>
Debugged-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: netfilter@vger.kernel.org
CC: Pablo Neira Ayuso <pablo@netfilter.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter fixes for net
The following patchset contains fixes for your net tree, they are:
* Remove extra quote from connlimit configuration in Kconfig, from
Randy Dunlap.
* Fix missing mss option in syn packets sent to the backend in our
new synproxy target, from Martin Topholm.
* Use window scale announced by client when sending the forged
syn to the backend, from Martin Topholm.
* Fix IPv6 address comparison in ebtables, from Luís Fernando
Cornachioni Estrozi.
* Fix wrong endianess in sequence adjustment which breaks helpers
in NAT configurations, from Phil Oester.
* Fix the error path handling of nft_compat, from me.
* Make sure the global conntrack counter is decremented after the
object has been released, also from me.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge dev
When the following commands are executed:
brctl addbr br0
ifconfig br0 hw ether <addr>
rmmod bridge
The calltrace will occur:
[ 563.312114] device eth1 left promiscuous mode
[ 563.312188] br0: port 1(eth1) entered disabled state
[ 563.468190] kmem_cache_destroy bridge_fdb_cache: Slab cache still has objects
[ 563.468197] CPU: 6 PID: 6982 Comm: rmmod Tainted: G O 3.12.0-0.7-default+ #9
[ 563.468199] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 563.468200] 0000000000000880 ffff88010f111e98 ffffffff814d1c92 ffff88010f111eb8
[ 563.468204] ffffffff81148efd ffff88010f111eb8 0000000000000000 ffff88010f111ec8
[ 563.468206] ffffffffa062a270 ffff88010f111ed8 ffffffffa063ac76 ffff88010f111f78
[ 563.468209] Call Trace:
[ 563.468218] [<ffffffff814d1c92>] dump_stack+0x6a/0x78
[ 563.468234] [<ffffffff81148efd>] kmem_cache_destroy+0xfd/0x100
[ 563.468242] [<ffffffffa062a270>] br_fdb_fini+0x10/0x20 [bridge]
[ 563.468247] [<ffffffffa063ac76>] br_deinit+0x4e/0x50 [bridge]
[ 563.468254] [<ffffffff810c7dc9>] SyS_delete_module+0x199/0x2b0
[ 563.468259] [<ffffffff814e0922>] system_call_fastpath+0x16/0x1b
[ 570.377958] Bridge firewalling registered
--------------------------- cut here -------------------------------
The reason is that when the bridge dev's address is changed, the
br_fdb_change_mac_address() will add new address in fdb, but when
the bridge was removed, the address entry in the fdb did not free,
the bridge_fdb_cache still has objects when destroy the cache, Fix
this by flushing the bridge address entry when removing the bridge.
v2: according to the Toshiaki Makita and Vlad's suggestion, I only
delete the vlan0 entry, it still have a leak here if the vlan id
is other number, so I need to call fdb_delete_by_port(br, NULL, 1)
to flush all entries whose dst is NULL for the bridge.
Suggested-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
This bug was introduced on commit 0898f99a2. This just recovers two
checks that existed before as suggested by Bart De Schuymer.
Signed-off-by: Luís Fernando Cornachioni Estrozi <lestrozi@uolinc.com>
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We should call vlan_vid_del for all vids at nbp_vlan_flush to prevent
vid_info->refcount from being leaked when detaching a bridge port.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should use wrapper functions vlan_vid_[add/del] instead of
ndo_vlan_rx_[add/kill]_vid. Otherwise, we might be not able to communicate
using vlan interface in a certain situation.
Example of problematic case:
vconfig add eth0 10
brctl addif br0 eth0
bridge vlan add dev eth0 vid 10
bridge vlan del dev eth0 vid 10
brctl delif br0 eth0
In this case, we cannot communicate via eth0.10 because vlan 10 is
filtered by NIC that has the vlan filtering feature.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull core locking changes from Ingo Molnar:
"The biggest changes:
- add lockdep support for seqcount/seqlocks structures, this
unearthed both bugs and required extra annotation.
- move the various kernel locking primitives to the new
kernel/locking/ directory"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
block: Use u64_stats_init() to initialize seqcounts
locking/lockdep: Mark __lockdep_count_forward_deps() as static
lockdep/proc: Fix lock-time avg computation
locking/doc: Update references to kernel/mutex.c
ipv6: Fix possible ipv6 seqlock deadlock
cpuset: Fix potential deadlock w/ set_mems_allowed
seqcount: Add lockdep functionality to seqcount/seqlock structures
net: Explicitly initialize u64_stats_sync structures for lockdep
locking: Move the percpu-rwsem code to kernel/locking/
locking: Move the lglocks code to kernel/locking/
locking: Move the rwsem code to kernel/locking/
locking: Move the rtmutex code to kernel/locking/
locking: Move the semaphore core to kernel/locking/
locking: Move the spinlock code to kernel/locking/
locking: Move the lockdep code to kernel/locking/
locking: Move the mutex code to kernel/locking/
hung_task debugging: Add tracepoint to report the hang
x86/locking/kconfig: Update paravirt spinlock Kconfig description
lockstat: Report avg wait and hold times
lockdep, x86/alternatives: Drop ancient lockdep fixup message
...
In order to enable lockdep on seqcount/seqlock structures, we
must explicitly initialize any locks.
The u64_stats_sync structure, uses a seqcount, and thus we need
to introduce a u64_stats_init() function and use it to initialize
the structure.
This unfortunately adds a lot of fairly trivial initialization code
to a number of drivers. But the benefit of ensuring correctness makes
this worth while.
Because these changes are required for lockdep to be enabled, and the
changes are quite trivial, I've not yet split this patch out into 30-some
separate patches, as I figured it would be better to get the various
maintainers thoughts on how to best merge this change along with
the seqcount lockdep enablement.
Feedback would be appreciated!
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Roger Luethi <rl@hellgate.ch>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Horman <horms@verge.net.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Wensong Zhang <wensong@linux-vs.org>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1381186321-4906-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pablo Neira Ayuso says:
====================
This batch contains fives nf_tables patches for your net-next tree,
they are:
* Fix possible use after free in the module removal path of the
x_tables compatibility layer, from Dan Carpenter.
* Add filter chain type for the bridge family, from myself.
* Fix Kconfig dependencies of the nf_tables bridge family with
the core, from myself.
* Fix sparse warnings in nft_nat, from Tomasz Bursztyka.
* Remove duplicated include in the IPv4 family support for nf_tables,
from Wei Yongjun.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
This is another batch containing Netfilter/IPVS updates for your net-next
tree, they are:
* Six patches to make the ipt_CLUSTERIP target support netnamespace,
from Gao feng.
* Two cleanups for the nf_conntrack_acct infrastructure, introducing
a new structure to encapsulate conntrack counters, from Holger
Eitzenberger.
* Fix missing verdict in SCTP support for IPVS, from Daniel Borkmann.
* Skip checksum recalculation in SCTP support for IPVS, also from
Daniel Borkmann.
* Fix behavioural change in xt_socket after IP early demux, from
Florian Westphal.
* Fix bogus large memory allocation in the bitmap port set type in ipset,
from Jozsef Kadlecsik.
* Fix possible compilation issues in the hash netnet set type in ipset,
also from Jozsef Kadlecsik.
* Define constants to identify netlink callback data in ipset dumps,
again from Jozsef Kadlecsik.
* Use sock_gen_put() in xt_socket to replace xt_socket_put_sk,
from Eric Dumazet.
* Improvements for the SH scheduler in IPVS, from Alexander Frolkin.
* Remove extra delay due to unneeded rcu barrier in IPVS net namespace
cleanup path, from Julian Anastasov.
* Save some cycles in ip6t_REJECT by skipping checksum validation in
packets leaving from our stack, from Stanislav Fomichev.
* Fix IPVS_CMD_ATTR_MAX definition in IPVS, larger that required, from
Julian Anastasov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
