Firmware loader: magical device bytes check updated (accepts all device
versions now and accepts possibly loaded firmware, if it is knowing to
be working)
Signed-off-by: Torsten Schenk <torsten.schenk@zoho.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Completion of signedness bug for pcm_runtime.rate: variable will never
get assigned a negative value now.
Signed-off-by: Torsten Schenk <torsten.schenk@zoho.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
wordsize is used as the textual width of a register address.
regsize is used as the textual width of a register value.
The assignments to these values were swapped. In the case of WM8903, which
has 8-bit register addresses and 16-bit register values, this caused the
register values to be clipped to 2 digits instead of the full 4.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch firstly restructurizes the code a bit by getting rid of continuous
checking for machine type in spitz_mic_bias().
Then the patch properly requests the MIC GPIO in the spitz_init() and frees it
in spitz_exit().
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_jack_gpio has a name field. Use that name when registering the IRQ,
since this is far more informative than the codec driver name. This shows
up in /proc/interrupts.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
pxa2xx_pcm_hw_free frees dma channel and sets prtd->dma_ch to -1,
but does not set prtd->params to NULL, so if pxa2xx_pcm_hw_params will
be called immediately, it leaves prtd->dma_ch initialized with -1,
and it results in oops in __pxa2xx_pcm_prepare. This bug is triggered
via SDL.
This patch adds check for prtd->dma_ch to __pxa2xx_pcm_prepare and
cleans prtd->params, so now it works properly.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: pcm: fix infinite loop in snd_pcm_update_hw_ptr0()
ALSA: HDA: Add dock mic quirk for Lenovo Thinkpad X220
ALSA: ens1371: fix Creative Ectiva support
ALSA: firewire-speakers: fix hang when unplugging a running device
ASoC: Fix CODEC device name for Corgi
ALSA: hda - Fix pin-config of Gigabyte mobo
ASoC: imx: fix burstsize for DMA
ASoC: imx: set watermarks for mx2-dma
ASoC: twl6040: Return -ENOMEM if create_singlethread_workqueue fails
ASoC: tlv320dac33: Restore L/R DAC power control register
ASoC: Explicitly say registerless widgets have no register
ASoC: tlv320dac33: Fix inconsistent spinlock usage
When period interrupts are disabled, snd_pcm_update_hw_ptr0() compares
the current time against the time estimated for the current hardware
pointer to detect xruns. The somewhat fuzzy threshold in the while loop
makes it possible that hdelta becomes negative; the comparison being
done with unsigned types then makes the loop go through the entire 263
negative range, and, depending on the value, never reach an unsigned
value that is small enough to stop the loop. Doing this with interrupts
disabled results in the machine locking up.
To prevent this, ensure that the loop condition uses signed types for
both operands so that the comparison is correctly done.
Many thanks to Kelly Anderson for debugging this.
Reported-by: Nix <nix@esperi.org.uk>
Reported-by: "Christopher K." <c.krooss@googlemail.com>
Reported-and-tested-by: Kelly Anderson <kelly@silka.with-linux.com>
Signed-off-by: Kelly Anderson <kelly@silka.with-linux.com>
[cl: remove unneeded casts; use a temp variable]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.38 <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This quirk is needed for the docking station mic of
Lenovo Thinkpad X220 to function correctly.
BugLink: http://bugs.launchpad.net/bugs/746259
Cc: stable@kernel.org
Tested-by: James Ferguson <james.ferguson@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is further fallout from delay.h removal from asm/apic.h and asm/dma.h:
ca444564a9: x86: Stop including <linux/delay.h> in two asm header files
Which caused this build failure:
sound/soc/codecs/sn95031.c: In function ‘sn95031_get_mic_bias’:
sound/soc/codecs/sn95031.c:153:2: error: implicit declaration of function ‘msleep’ [-Werror=implicit-function-declaration]
Cc: Jean Delvare <khali@linux-fr.org>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20110325152014.297890ec@endymion.delvare>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When syncing the cache, if the driver has given us a writable_register()
callback, use it to check if we are syncing a non-writable register
and if so warn the user.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To make the EV1938 chip work, add a magic bit and an extra delay.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Tino Schmidt <mailtinoshomepage@gmx.net>
Cc: all 2.6.x <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When aborting a PCM stream, the xrun is signaled only if the stream is
running. When disconnecting a PCM stream, calling snd_card_disconnect()
too early would change the stream into a non-running state and thus
prevent the xrun from being noticed by user space.
To prevent this, move the snd_card_disconnect() call after the xrun.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the initialization of .codec_dai_name in zylonite_dai initializer,
do not mix it with the initialization of .codec_name which is set
already a few lines above.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we have multi-component support, take the time to unify the
SPORT implementations a bit and make the setup dynamic. This kills
off the global sport_handle which was shared across all the Blackfin
machine drivers. The pin management aspect is off loaded to platform
resources, and now multiple SPORTs can be instantiated simultaneously.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some machine drivers were using "bf5xx-", others were using "bf5xx_",
while others were using "bfin-". Further, some were using the same
name in the transport layer which makes it hard to use different codecs
at the same time. So standardize all of them to "bfin-" and make sure
they are name spaced according to their driver name.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The recent multi-component patch incorrectly added "-codec" suffixes to
parts which are not MFD. Drop the suffix from the machine drivers too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The codec name should not have a "-codec" suffix since this is not part of
a MFD. This was incorrectly changed during the multi-component updated.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The codec name should not have a "-codec" suffix since this is not part of
a MFD. This was incorrectly changed during the multi-component updated.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The codec name should not have a "-codec" suffix since this is not part of
a MFD. This was incorrectly changed during the multi-component updated.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The codec name should not have a "-codec" suffix since this is not part of
a MFD. This was incorrectly changed during the multi-component updated.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Got typoed in the multi-component changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: Fix yet another race in disconnection
ALSA: asihpi - Update verbose debug print macros
ALSA: asihpi - Improve non-busmaster adapter operation
ALSA: asihpi - Support single-rate no-SRC cards
ALSA: HDA: New AD1984A model for Dell Precision R5500
ALSA: vmalloc buffers should use normal mmap
ALSA: hda - Fix SPDIF out regression on ALC889
ALSA: usb-audio - Support for Boss JS-8 Jam Station
ALSA: usb-audio: add Cakewalk UM-1G support
sound/oss/opl3: validate voice and channel indexes
sound/oss: remove offset from load_patch callbacks
The AD73311 codec does not use I2C, so don't require it in Kconfig.
Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename the snd_soc_control_type field from "bus_type" to "control_type",
and drop the now unused "control_data" field.
Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide the top level ASoC core functions for indicating whether
a given register is readable or writable.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
By using struct snd_soc_reg_access for the read/write/vol attributes
of the registers, we provide callbacks that automatically determine whether
a given register is readable/writable or volatile.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These functions fail with -EINVAL if the corresponding callbacks
are not implemented. Change them to return -ENOSYS as it is more
appropriate for unimplemented callbacks.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The handling of all snd_soc_x_y_spi_write() functions is similar.
Create a separate function and update all callers to use it.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The handling of all snd_soc_x_y_read() functions is similar.
Factor it out into a separate function and update all callers.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The handling of all snd_soc_x_y_write() functions is similar.
Factor it out into a separate function and update all functions
to use it.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As it has become more common to have to write firmware or similar
large chunks of data to the hardware, add a function to perform
raw bulk writes that bypass the cache. This only handles volatile
registers as we should avoid getting out of sync with the actual
cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The handling of all snd_soc_x_y_read_i2c() functions is similar.
Make a generic I2C read function and update all callers to use it.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Checking if IMX_SSI_DMA is set and then set it again is useless.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SSI counts in words, the DMA engine in bytes. (Wrong) factor got removed
in bf974a0 (ASoC i.MX: switch to new DMA api).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
They got accidently removed by f0fba2a (ASoC: multi-component - ASoC
Multi-Component Support). Reintroduce them and get rid of the
superfluous defines because the fiq-driver has its own hardcoded values.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Move the codec power on (in reg 0x01, bit 4) from
set_bias_level:SND_SOC_BIAS_ON to a DAPM supply.
In this way we can be sure, that all the things within
the codec is powered before the external amp is
going to be enabled.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Register 0x40, 0x41 need to be restored after power up, since
it contains gain related fields, which affects playback volume.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch fixes a race between snd_card_file_remove() and
snd_card_disconnect(). When the card is added to shutdown_files list
in snd_card_disconnect(), but it's freed in snd_card_file_remove() at
the same time, the shutdown_files list gets corrupted. The list member
must be freed in snd_card_file_remove() as well.
Reported-and-tested-by: Russ Dill <russ.dill@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace local VPRINTK1 with snd_printdd.
Create local snd_printddd instead of VPRINTK2 for most verbose debug.
In most cases let snd_printk supply default level for messages.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make playback silence callback a no-op, card automatically outputs
silence when written data runs out.
Increasing update interval and thus minimum period avoids xrun on startup
or because of timer jitter.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cards without settable local samplerate and without SRC
still must have a valid samplerate.
This fixed rate is determined by reading the current rate for the card.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For codec AD1984A, add a new model to support Dell Precision R5500
or the microphone jack won't work correctly.
BugLink: http://bugs.launchpad.net/bugs/741516
Tested-by: Kent Baxley <kent.baxley@canonical.com>
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's a big no-no to use pgprot_noncached() when mmap'ing such buffers
into userspace since they are mapped cachable in kernel space.
This can cause all sort of interesting things ranging from to garbled
sound to lockups on various architectures. I've observed that usb-audio
is broken on powerpc 4xx for example because of that.
Also remove the now unused snd_pcm_lib_mmap_noncached(). It's
an arch business to know when to use uncached mappings, there's
already hacks for MIPS inside snd_pcm_default_mmap() and other
archs are supposed to use dma_mmap_coherent().
(See my separate patch that adds dma_mmap_coherent() to powerpc)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
Update unsolicited event process function via_unsol_event() to
make it can process more unsolicited events.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add some hardware related verbs in VT2002P initial verbs.
These verbs are used to fix Class-D speaker no sound issue.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a verb to enable control amplifier of stereo mixer in VT1718S
initial verbs. Set stereo mixer default amplifier value as un-mute.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a verb of power down jack detect in VT1708 initial verbs.
This verb is used to avoid noise caused by hardware issue.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modify side_mute_channel() and update_side_mute_status() functions
to fix invalid side channel mute issue of VT2002P, VT1812 and VT1802
codecs.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 5a8cfb4e8a
ALSA: hda - Use ALC_INIT_DEFAULT for really default initialization
changed to use the default initialization method for ALC889, but
this caused a regression on SPDIF output on some machines.
This seems due to the COEF setup included in the default init procedure.
For making SPDIF working again, the COEF-setup has to be avoided for
the id 0889.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24342
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a quirk for the Cakewalk UM-1G USB MIDI interface in
"advanced driver" mode. (It already works in standard mode.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
User-controllable indexes for voice and channel values may cause reading
and writing beyond the bounds of their respective arrays, leading to
potentially exploitable memory corruption. Validate these indexes.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Was: [PATCH] sound/oss/midi_synth: prevent underflow, use of
uninitialized value, and signedness issue
The offset passed to midi_synth_load_patch() can be essentially
arbitrary. If it's greater than the header length, this will result in
a copy_from_user(dst, src, negative_val). While this will just return
-EFAULT on x86, on other architectures this may cause memory corruption.
Additionally, the length field of the sysex_info structure may not be
initialized prior to its use. Finally, a signed comparison may result
in an unintentionally large loop.
On suggestion by Takashi Iwai, version two removes the offset argument
from the load_patch callbacks entirely, which also resolves similar
issues in opl3. Compile tested only.
v3 adjusts comments and hopefully gets copy offsets right.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: HDA: Realtek: Avoid unnecessary volume control index on Surround/Side
ASoC: Support !REGULATOR build for sgtl5000
ALSA: hda - VIA: Fix VT1708 can't build up Headphone control issue
ALSA: hda - VIA: Correct stream names for VT1818S
ALSA: hda - VIA: Fix codec type for VT1708BCE at the right timing
ALSA: hda - VIA: Fix invalid A-A path volume adjust issue
ALSA: hda - VIA: Add missing support for VT1718S in A-A path
ALSA: hda - VIA: Fix independent headphone no sound issue
ALSA: hda - VIA: Fix stereo mixer recording no sound issue
ALSA: hda - Set EAPD for Realtek ALC665
ALSA: usb - Remove trailing spaces from USB card name strings
sound: read i_size with i_size_read()
ASoC: Remove bogus check for register validity in debugfs write
ASoC: mini2440: Fix uda134x codec problem.
Add support for VT1802 codec, which is similiar with VT2002P
except VT1802 has no Class-D and has some different pin widget
id.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for VT1705 codec, which is similiar with VT1708S
except it has 6 channels output.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use mfd_data for passing information from mfd drivers to soc
clients. The mfd_cell's driver_data field is being phased out.
Clients that were using driver_data now access .mfd_data
via mfd_get_data().
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use mfd_data for passing information from mfd drivers to soc
clients. The mfd_cell's driver_data field is being phased out.
Clients that were using driver_data now access .mfd_data
via mfd_get_data().
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use set_widgets_power_state() function to seperately control different
codecs' power management actions and to replace the original large
function. Also fix some wrong widgets power up sequence which caused
no sound issue under Smart5.1 mode and Independent HP mode.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar to commit 7e59e097c0, this patch
avoids unnecessary volume control indices for more
Realtek auto-parsers, e g the ALC66x family, on the "Surround" and "Side"
controls.
These indices cause these volume controls to be ignored by PulseAudio and
vmaster and should be removed whenever possible.
Cc: stable@kernel.org
Reported-by: Jan Losinski <losinski@wh2.tu-dresden.de>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DSP2 in the WM8958 can be used to support an upgraded EQ for use in
demanding applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
With appropriate firmware the WM8958 can support Virtual Surround Sound or
VSS, widening the stereo audio image for improved user experience. Enable
support for this mode of operation when the appropriate firmware can be
loaded at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In preparation for the addition of additional WM8958 algorithms
reorganise the code to make it easier to add such support later.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow userspace to supply an update to the ROM firmware. The firmware
request is non-blocking so userspace can load the firmware at its
leisure without delaying startup, the driver will begin using the
firmware the next time MBC is started after it has been supplied.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The regulator is optional depending on board design.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The lock is used within the interrupt handler.
Correct the spinlock usage, and use irqsave/irqrestore
flavour of spin_lock/unlock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add a function to dynamically replace a given control. If the
control does not already exist, a third parameter is used to determine
whether to actually add that control. This is useful in cases where
downloadable firmware at runtime can add or replace existing controls.
A separate patch needs to be made to allow ALSA Mixer to render the
replaced controls on the fly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since VT1708 didn't support the control of getting connection number,
building of headphone control will fail in via_hp_build() function.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct stream names of analog playback and capture streams
for VT1818S.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add get_codec_type() in via_new_spec() function to make sure getting
correct codec type before building mixer controls.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modify mute_aa_path() function to support VT1718S codec.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modify via_independent_hp_put() function to support VT1718S and VT1812
codecs, and fix independent headphone no sound issue.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These changes are needed to keep up with the changes in the
MFD core and V4L2 parts of the wl1273 FM radio driver.
Use function pointers instead of exported functions for I2C IO.
Also move all preprocessor constants from the wl1273.h to
include/linux/mfd/wl1273-core.h.
Also update the year in the copyright statement.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add TEA5757 radio tuner support to es1968 driver. This is found at least on
MediaForte SF64-PCE2 sound cards.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Improve tea575x-tuner with various good things from radio-maestro:
- extend frequency range to 50-150MHz
- fix querycap(): card name, CAP_RADIO
- improve g_tuner(): CAP_STEREO, stereo and tuned indication
- improve g_frequency(): tuner index checking and reading frequency from HW
- improve s_frequency(): tuner index and type checking
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some USB devices give trailing spaces in strings returned from
usb_string(). This confuses the automatic card-id creation, resulting
always in "default".
This patch fixes the behavior by removing trailing spaces.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
Convert direct read of inode->i_size to using i_size_read().
i_size_read is guaranteed to return a valid value and
its caller does not need to use addtional locking.
Signed-off-by: Xiaochen Wang <wangxiaochen0@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The DSP2 startup requires that the clock be enable so if we've deferred
clock startup we need to defer DSP2 startup
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
DSP2 on the WM8958 has a default ROM which provides a multi-band
compressor for enhanced performance on mobile devices but can also
support runtime download of alternative firmware. In preparation for
more exploiting this functionality refactor the code to split the
handling of DSP2 into a separate file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The first WM8958 revision requires similar treatment.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Since not all registers need to be cached and the cache is entirely
optional anyway we shouldn't be checking that a register is in the
cached range. If the register is invalid then the actual I/O code
can determine that and report an error.
Similarly, the step size can and should be enforced by the lower level
code if it's important.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The user-supplied index into the adapters array needs to be checked, or
an out-of-bounds kernel pointer could be accessed and used, leading to
potentially exploitable memory corruption.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
loopback_pos_update() can be called in the timer callback, thus the lock
held should be irq-safe. Otherwise you'll get AB/BA deadlock together
with substream->self_group.lock.
Reported-and-tested-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
fixes this error:
sound/firewire/fcp.c: In function 'fcp_avc_transaction':
sound/firewire/fcp.c:103: error: implicit declaration of function 'msleep'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add an AMDTP stream error state that occurs when we fail to queue
another packet. In this case, the stream is stopped, and the error can
be reported when the application tries to restart the PCM stream.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For correct cache coherency on some architectures, DMA buffers must be
allocated in a different cache line than data that is concurrently used
by the CPU.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In non-blocking mode, the SYT_INTERVAL is larger than the number of
audio frames in each packet, so there are packets that do not contain
any frame to which the SYT could be applied. For these packets, the
SYT must not be the timestamp of the next valid SYT frame, but the
special no-info SYT value.
This fixes broken playback on the FireWave at 44.1 kHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a driver for two playback-only FireWire devices based on the OXFW970
chip.
v2: better AMDTP API abstraction; fix fw_unit leak; small fixes
v3: cache the iPCR value
v4: FireWave constraints; fix fw_device reference counting;
fix PCR caching; small changes and fixes
v5: volume/mute support; fix crashing due to pcm stop races
v6: fix build; one-channel volume for LaCie
v7: use signed values to make volume (range checks) work; fix function
block IDs for volume/mute; always use channel 0 for LaCie volume
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch replaces use of the harcoded arrays of pins, muxes, digital
mics and adcs with the auto-generated ones using codec parsing and
auto-discovers all actually connected digital mic pins on 92HD8X-like
codecs
This patch also adds the support for d-mic on pin 0x20.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the mux for digital mic is different from the mux for other mics,
the current auto-parser doesn't handle them in a right way but provides
only one mic. This patch fixes the issue.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the default input-src selection code for alc268/269 to the init
part instead of the parser. The input-src selection might be overwritten
by init verbs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently some special handling for the unusual case like dual-ADCs
or a single-input-src is done in the tree-parse time in
set_capture_mixer(). But this setup could be overwritten by static
init verbs.
This patch moves the initialization into the init phase so that
such input-src setup won't be lost.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SDPIF status retrieval always returned the default settings instead of
the actual ones.
Signed-off-by: Przemyslaw Bruski <pbruskispam@op.pl>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
microphone boost was set at +12dB, not +20dB (like in Windows driver
and in adc_conf structure declaration), some comments added.
Signed-off-by: Przemyslaw Bruski <pbruskispam@op.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: Ensure WM8958 gets all WM8994 late revision widgets
ASoC: Fix typo in late revision WM8994 DAC2R name
ASoC: Use the correct DAPM context when cleaning up final widget set
ASoC: Fix broken bitfield definitions in WM8978
ASoC: AM3517: Update codec name after multi-component update
The time-out in snd_atiixp_aclink_reset() is wrongly checked, and
it resulted in exiting from the loop at the first iteration.
Reported-by: Amir Shamsuddin <AmirS2+alsa@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Appending an 'm' will distinguish it from a similar struct in intel8x0.c
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding an 'm' will distinguish them from identical names in intel8x0.c.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At every resume a laptop I use prints this message (at KERN_ERR level):
ALSA sound/pci/intel8x0m.c:904: AC'97 warm reset still in progress? [0x2]
The thing to note here is that 0x2 corresponds to ICH_AC97COLD. Ie, what
seems to be happening is that the register involved indicated a warm
reset for some time (as the ICH_AC97WARM bit was set) but by the time
the warning is printed, and that same register is checked again, that
bit is already cleared and only the ICH_AC97COLD bit is still set.
It turns out a warm reset needs some time to settle, but it is currently
checked right away. The test therefore fails the first time it is done
and schedule_timeout_uninterruptible() will be called. Once we return
from that jiffies is already (far) past end_time on this laptop, so we
exit the loop, print a warning, and exit the function while the warm
reset actually succeeded.
A way to fix this is to call usleep_range() after writing to the
register involved. A handful of tests suggest 500 usecs is a safe value.
(This might punish the "finish cold reset" case, but on this laptop such
a cold reset apparently never happens, so I can't say for sure.)
While we're at it drop the extra single tick from end_time, as it looks
rather silly.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Devices are autosuspended if no pcm nor midi channel is open
Mixer devices may be opened. This way they are active when
in use to play or record sound, but can be suspended while
users have a mixer application running.
[Small clean-ups using static inline by tiwai]
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- ESHUTDOWN must be correctly handled
- the optional interrupt endpoint's URB must be stopped and restarted
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC audio for mini2440 platform in current kenrel doesn't work.
First problem is samsung_asoc_dma device is missing in initialization.
Next problem is with codec. Codec is initialized but never probed
because no platform_device exist for codec driver. It leads to errors
during codec binding to asoc dai. Next problem was platform data which
was passed from board to asoc main driver but not passed to codec when
called codec_soc_probe().
Following patch should fix issues. But not sure if in correct way.
Please review.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
MONO was renamed to MONO1.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This patch adds ASoC support for the MAX9850 codec with headphone
amplifier.
Supported features:
- Playback
- 16, 20 and 24 bit audio
- 8k - 48k sample rates
- DAPM
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added a new API function snd_ctl_activate_id() for activate / inactivate
the control element dynamically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
azx_init_pci() always writes PCI config register ICH6_PCIREG_TCSEL
although this looks to be only defined on Intel systems and has a
different meaning on AMD systems. On AMD systems the PCI interrupt pin
control register is modified instead.
Since the meaning of offset 0x44 in device specific configuration space is
unknown for devices by other vendors, we only exclude AMD systems to
retain the current behaviour.
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Do not initialize again the what has already been initialized as
multi outs, as this breaks surround speakers.
Tested-by: Bartłomiej Żogała <nusch88@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without this change, a volume control named "Surround" or "Side" would
get an unnecessary index, causing it to be ignored by the vmaster and
PulseAudio.
Tested-by: Bartłomiej Żogała <nusch88@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When more than one pair of internal speakers is present, allow names
according to their channels.
Tested-by: Bartłomiej Żogała <nusch88@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pin config values would change the association instead of the
sequence, this commit fixes that up.
Tested-by: Bartłomiej Żogała <nusch88@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
One more affected devices: Logitech Webcam C600 (046d:0808)
Volume range before quirk is 6400, after (also real) is 16.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without this fix the driver won't instantiate properly on relevant
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
Without this fix the driver won't instantiate properly on relevant
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
Since OSS driver creates the device entries for /dev/audio* and
/dev/dspW* by itself without coping with sound_core, it leads to
conflicts with others and let sysfs spewing warnings.
This patch rewrites the registration part of OSS driver to use
the standard method also for additional minor devices.
Reported-by: Steven Rostedt <rostedt@goodmis.org> (with ktest.pl)
Tested-by: Steven Rostedt <rostedt@goodmis.org> (with ktest.pl)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable 192kHz sample rate for EP93xx.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Improve EP93xx I2S clocks management.
Some freqs values are set not exact as they requested for MCLK and
original code was not able to find divisors for SCLK and LRCLK.
This code just picks up nearest value from 3 possible variants.
This patch makes 44100 and 192000 rates working and fixes
capture function (by selecting SCLK/LRCLK=64 where possible).
All other rates should work as before.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Manage I2S rates according to datasheet for CS4271 CODEC in EDB93xx
machine driver.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Manage mode and rate bits correctly, according to datasheet in CS4271 CODEC.
This is done to make capture work properly.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're not only prefixing all controls, we're also prefixing the widget
names in the runtime data. This causes us to add the prefix twice - once
when using the widget name to generate the control name and once when
adding the control.
Really we shouldn't be prefixing the widget names at all, the matching
code should be handing this as we always know which DAPM context a
widget came from and always display the widget name in terms of a DAPM
context. However, we're quite close to the merge window and that's
relatively invasive.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Now we've got multi-component we need to make sure that the DAPM context
(and hence register I/O context) we use to apply the pending updates at
the end of a DAPM sequence is the one we were processing rather than the
one that was used to initate the state change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Now we have a register write minimisation code in DAPM we don't need to
worry about the ordering of the enable and disable of the PGA and the
output stage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The i2c client device name (".2-001a" in this case, including
the separator period) for the AIC23 codec on the TI AM3517-EVM
was appended to the codec_name member of am3517evm_dai to
resolve the names mismatch happening in soc_bind_dai_link(),
due to which the card was not getting registered.
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
McBSP sidetone is needed in telephony applications. McBSP sidetone is a
configurable FIR filter that forms a loopback from McBSP input to output.
This patch enables the McBSP2 sidetone ALSA controls so that it can be used
on Nokia RX-51/N900.
Sidetone feature can be tested with following commands:
(set up codec input and output paths)
# Enable and configure sidetone
amixer -D hw:0 set 'McBSP2 Sidetone' on
amixer set -D hw:0 'McBSP2 Sidetone Channel 0' 32767
echo 32767 >/sys/devices/platform/omap-mcbsp.2/st_taps
# Do not loop audio via CPU
arecord -f dat >/dev/null |aplay /dev/zero
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The "ldo" variable was dereferenced after free on the error path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently will ignore prefixes when creating DAPM controls. Since currently
all control creation goes through snd_soc_cnew() we can fix this by factoring
the prefixing into that function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Symmetric rate configuration can fail if the second stream starting tries
to apply the symmetric constraint before the first stream has got far
enough to pick a rate. Rather than try to enforce a nonsensical rate of
0Hz log a warning and allow the application to carry on. Things might go
wrong later on but the user will know about it and there's unlikely to be
lasting damage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
When multi component systems use DAIless amplifiers which require clocking
configuration it is at best hard to use the current clocking API as this
requires a DAI even though the device may not even have one. Address this
by adding set_sysclk() and set_pll() operations and APIs for CODECs.
In order to avoid issues with devices which could be used either with or
without DAIs make the DAI variants call through to their CODEC counterparts
if there is no DAI specific operation. Converting over entirely would create
problems for multi-DAI devices which offer per-DAI clocking setup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Annoying as the __devinitdata is actually correct.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow a slight simplification of CODEC drivers by allowing DAPM routes and
widgets to be provided in a table. They will be instantiated at the end of
CODEC probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The return value of snd_ctl_hole_check() is used only to detect whether
to continue the loop in snd_ctl_find_hole() or not, so we can simplify
the code by changing this return type to a boolean. Also rename this
function to better show what it actually does.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The purpose of the snd_ctl_hole_check() function is to find conflicts
between the numerical IDs of the new control and those of any existing
controls. However, it would fail to detect an existing control whose
count is smaller than the new control's count and whose interval of IDs
is entirely contained in the interval of the new control's IDs.
To fix this, use the correct formula to detect overlapping intervals,
which happens to simplify the condition.
This problem was not encountered so far because ALSA does not yet allow
drivers to allocate specific control IDs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current AES32 firmware revision ID is 234, however, a user confirmed
that everything works fine with the previous revision, too.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove warnings in ep93xx-i2s.c
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Extend range of supported sample rates for CS4271 CODEC.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a codec driver for the dfbmcs320 bluetooth module, which is used
on the neo1973 boards.
The patch also modifies the neo1937_wm8753 sound board driver to use the new
driver instead of registering the bluetooth DAI manually.
Previously there was a name mismatch between the bluetooth DAI and the bluetooth
DAI link and the sound card was not instantiated, with this patch the issue is
no longer present and sound support works again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The neo1973(GTA01) and neo1973_gta02(GTA02) have a very similar audio hardware
setup. They both use the same codec with the same routing to the gsm modem and
bluetooth chip. But they do use different AMPs though and there are some minor
differences in the speaker setup.
As a result most of the code of those two drivers is identical.
So from a maintenance point of view it makes sense to merge them into a single
driver. It also reduces the size of kernel images supporting both the GTA01 and
GTA02.
As a side-effect of this merge the GTA01 for example gains support for routing
audio to and from the bluetooth DAI.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using gpio_request_array instead of requesting and setting up each gpio by hand
makes the code more readable and more compact.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch drops the lm4853_{set,get}_state functions and the "Amp State Switch"
control.
Those were noops which existed to maintain alsa state file compatibility. Since
the control names have changed due to internal changes in the ASoC core and
state file compatibility was broken anyway it makes sense to drop them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch moves the code for the lm4857 AMP from the neo1973_wm8753 sound
board driver to its own module.
The lm4857 is a generic AMP IC and not specific to the neo1973.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It has been proven to be inflexible to do scenario management in kernel space.
Since actual neo1973 board support has not been merged in mainline and this
patch has been in the neo1973 tree for some time now it should be safe to remove
this functionality without breaking existing userspace.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Visstrim_M10 boards have an external tlcv320aic3205 codec
attached to SSI1. This driver glues together both interfaces.
External amplifier is not supported in this first version.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Don't set to D3 in Cirrus errata init verbs
ALSA: hda - add new Fermi 5xx codec IDs to snd-hda
ASoC: WM8994: Ensure late enable events are processed for the ADCs
ASoC: WM8994: Don't disable the AIF[1|2]CLK_ENA unconditionaly
ASoC: Fix WM9081 platform data initialisation
ALSA: hda - Fix unable to record issue on ASUS N82JV
ALSA: HDA: Realtek: Fixup jack detection to input subsystem
This patch adds support for tlv320aic3205 and tlv320aic3254 codecs.
It doesn't include miniDSP support for aic3254.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The errata init verbs for CS42xx codecs contain the verbs to set
the power-state of SPDIF nodes to D3, which seem to break the SPDIF
output on some MacBooks. Since this is executed during the power-up
initialization, we shouldn't turn them down there.
Reported-by: Arun Raghavan <arun.raghavan@collabora.co.uk>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since multiple codec drivers already use the input-jack stuff, let's
make common helper functions to reduce the duplicated codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the missing HDMI codec IDs for new Nvidia stuff.
Note that ID 0x17 isn't assigned to anything so far, as suggested by
Stephen.
[Modified to get rid of 0x17 by tiwai]
Signed-off-by: Richard Samson <samson.richard@gmail.com>
Acked-by: Acked-By: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is run after the DAPM widgets and routes are added, allowing setup
of things like jacks using the routes. The main card probe() is run before
anything else so can't be used for this purpose.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
These will be added after all devices are registered and allow most DAI
init functions in machine drivers to be replaced by simple data.
Regular controls are not supported as the registration function still
works in terms of CODECs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This means that rather than adding the board specific DAPM widgets to a
random CODEC DAPM context they can be added to the card itself which is
a bit cleaner. Previously there only was one DAPM context and it was
tied to the single supported CODEC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
A CODEC pointer is optional (and is checked for in most contexts within
DAPM) - add checks to the few places where it was missed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Rather than indirecting through the CODEC we can look the card up directly
from the card pointer in the DAPM context.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The patch 'ASoC: WM8994: Improve Playback Robustness' did not handle
this case properly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM9081 IRQ output can be either active high or active low and can
support either CMOS or open drain modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
When choosing IMX_DMA flag, burtsizes are set to its default
value (0) which leads to driver malfunction. Change them to 4.
DSP_B interface needs additional flag to match DSP_B formats
as described in several codecs as wm8741 and aic3205.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch 'ASoC: WM8994: Improve Playback Robustness' did not handle
this case properly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that the ADCs are provided with a clock as the previous patch
"ASoC: WM8994: Improve playback robustness" did not handle this case
properly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Since we began using the late clock disable functionality, ensure that
we don't disable the clock if any of the ADC or DAC paths are still
enabled. This happens when we have simultaneous playback and recording.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
It went AWOL in the multi-component conversion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
eukrea-tlv320: fix platform_name
ASoC: correct pxa AC97 DAI names
ALSA: hda - Add support for new IDT 92HD98 and 92HD99 codecs
ALSA: HDA: Add ideapad quirk for two Dell machines
ALSA: HDA: Add a new Conexant codec 506e (20590)
ALSA: usb-audio: fix oops due to cleanup race when disconnecting
ASoC: Hook wm_hubs micbiases up to CLK_SYS
ASoC: Correct definition of WM8903_VMID_RES_5K
ASoC: Fix WM8958 default microphone detection argument ordering
ALSA: HDA: Fix mic initialization in VIA auto parser
ALSA: fix one memory leak in sound jack
Get rid of users of of_platform_driver in drivers/sound. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch fixes an error in the jack detection reporting,
causing the jack detection sometimes not to be reported
correctly to the input subsystem. It should apply to several
Realtek codecs.
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
tegra_dma_allocate_channel() returns NULL on errors, not an error pointer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Depending on the model and the presence of a TCO module, the number of
midi ports varies. Some have 1 port (MADIface), some have 2 (default),
with TCO, there are 3.
Don't hardcode the number of midi ports to initialize.
This patch also fixes a boot lockup on MADIface.
[Coding-style fixes by tiwai]
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In contrast to the PCIe version (RME AES), the PCI version (RME AES32)
has a different firmware revision.
This patch adds the missing PCI revision.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove unnecessary headers:
- mach/hardware.h in sgtl5000.c
- linux/i2c.h in sgtl5000.h
Signed-off-by: Zeng Zhaoming <b32542@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow input from microphone on remaining PowerBooks and iBooks with Tumbler.
Tested only with PowerBook G4 Gigabit Ethernet (PowerBook3,3).
[Fixed to use of_machine_is_compatible by tiwai]
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Patch below removes one to many "n's" in a word..
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Liam Girdwood <lrg@slimogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There's a general move to use dev_pm_ops rather than bus specific functions
in order to facilitate work on the PM core. Do this conversion to WM2000.
The driver ought to be updated to work better in a multi-component model
but the mechanical conversion ensures that we avoid blocking PM core work
until that happens.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
commit f0fba2ad1b included a mistake
on the name of the platform in the snd_soc_dai_link structure.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The utilities will be required by every machine driver. Including the
utility object directly into every machine driver causes a build failure
if the modules are actually built into the kernel, since each will define
the symbols exported by the utility file. Solve this by moving the
utility object into a separate module.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes the name of the control switch of a dapm route contains
spaces which makes it impossible to distinguish it from the source widget.
Add quotes around the names of the widgets to makes these parsable.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct names for pxa AC97 DAI are pxa2xx-ac97 and pxa2xx-ac97-aux. Fix
that for all PXA platforms.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Removed the use of macros to obtain base address and DMA channel number.
Instead use the McBSP driver API's that passes base address and DMA
channel number to the client driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Also fix number of 92HD87 pins to exclude invalid pins.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We're currently not passing anything and this will make the card and so on
more discoverable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Lately I sent patch that switched lfe with side in mixer for
acer-aspire-4930g. Then I connected 5.1 speaker system and noticed that
lfe slider wasn't working and that old lfe slider worked. What I'm doing
now is:
- reverting old patch
- adding internal lfe slider
- removing side as it is superfluous (ALC888S-VC is 7.1 but in fact
laptop can only do 5.1 and it is so in drivers for MS Windows)
Signed-off-by: Łukasz Wojniłowicz <lukasz.wojnilowicz@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These two Dell machines have been reported working well with
the ideapad model.
BugLink: http://bugs.launchpad.net/bugs/723676
Cc: stable@kernel.org
Tested-by: David Chen <david.chen@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conexant 506e/20590 has the same graph as the rest of the 5066 family.
BugLink: http://bugs.launchpad.net/bugs/723672
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Original patch by Dan Rosenberg <drosenberg@vsecurity.com> under commit
e68d3b316a. I'm copying his text here:
The SNDRV_HDSPM_IOCTL_GET_CONFIG_INFO ioctl in hdspm.c allow unprivileged
users to read uninitialized kernel stack memory, because several fields
of the hdspm_config struct declared on the stack are not altered
or zeroed before being copied back to the user. This patch takes care
of it.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fredrik Lingvall <fredrik.lingvall@gmail.com> has discovered wrong
frequency and sync detection on AES32. According to him, the provided
patch fixes these issues.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In contrast to the RME MADI card, coax/optical selection on the MADIface
is done via a physical switch located at the breakout box. Obviously,
the driver cannot switch ports in software.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Caused by two typos, no output channel mappings were assigned for
MADI/MADIface at double/quad speed.
The channel mapping is indeed identical to the single speed mapping, the
cards will simply use the first N channels.
Signed-off-by: Florian Faber <faber@faberman.de>
Signed-off-by: Fredrik Lingvall <fredrik.lingvall@gmail.com>
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without calling an appropriate rule, AES/AES32 cards would announce a
theoretical channel count of 64 (HDSPM_MAX_CHANNELS), leading to the
already known bug:
[37422.640481] ------------[ cut here ]------------
[37422.640487] WARNING: at sound/pci/rme9652/hdspm.c:5449
snd_hdspm_ioctl+0x18f/0x202 [snd_hdspm]()
[37422.640489] Hardware name: PRIMERGY RX100 S6
[37422.640490] BUG? (info->channel >= hdspm->max_channels_in)
[37422.640492] Modules linked in: snd_hdspm snd_seq_midi ipmi_watchdog
ipmi_poweroff ipmi_si ipmi_devintf ipmi_msghandler i2c_i801 e1000e
snd_rawmidi power_meter [last unloaded: snd_hdspm]
[37422.640501] Pid: 22231, comm: jackd Tainted: G D W
2.6.36-gentoo-r5 #5
[37422.640502] Call Trace:
[37422.640508] [<ffffffff8103db3a>] warn_slowpath_common+0x80/0x98
[37422.640511] [<ffffffff8103dbe6>] warn_slowpath_fmt+0x41/0x43
[37422.640514] [<ffffffff81034306>] ? get_parent_ip+0x11/0x42
[37422.640518] [<ffffffffa0055763>] snd_hdspm_ioctl+0x18f/0x202
[snd_hdspm]
[37422.640522] [<ffffffff813fd626>] snd_pcm_channel_info+0x73/0x7c
[37422.640525] [<ffffffff814001e9>] snd_pcm_common_ioctl1+0x326/0xb01
[37422.640527] [<ffffffff81034306>] ? get_parent_ip+0x11/0x42
[37422.640531] [<ffffffff8105be6c>] ? __srcu_read_unlock+0x3b/0x59
[37422.640533] [<ffffffff81400bce>] snd_pcm_capture_ioctl1+0x20a/0x227
[37422.640537] [<ffffffff811e599c>] ? file_has_perm+0x90/0x9e
[37422.640540] [<ffffffff81400c15>] snd_pcm_capture_ioctl+0x2a/0x2e
[37422.640543] [<ffffffff810f2c69>] do_vfs_ioctl+0x404/0x453
[37422.640546] [<ffffffff810f2d09>] sys_ioctl+0x51/0x74
[37422.640549] [<ffffffff81002aab>] system_call_fastpath+0x16/0x1b
[37422.640552] ---[ end trace 0cd919cd68118082 ]---
We already have all the right values in place, we simply have to inform
the upper layers about this restriction.
Note that snd_hdspm_hw_rule_rate_out_channels and
snd_hdspm_hw_rule_rate_in_channels must not be called on AES32, because
the channel count is always 16, no matter of the samplerate in use.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only RayDAT and AIO provide sane buffer pointers that can be used with
HDSPM_BufferPositionMask, on all other cards, this would result in a
wrong HW pointer leading to xruns and these messages:
[260808.916788] BUG: pcmC0D0p:0, pos = 2976, buffer size = 1024, period size = 512
[260808.961124] BUG: pcmC0D0c:0, pos = 4944, buffer size = 1024, period size = 512
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a USB audio device is disconnected, snd_usb_audio_disconnect()
kills all audio URBs. At the same time, the application, after being
notified of the disconnection, might close the device, in which case
ALSA calls the .hw_free callback, which should free the URBs too.
Commit de1b8b93a0 "[ALSA] Fix hang-up at disconnection of usb-audio"
prevented snd_usb_hw_free() from freeing the URBs to avoid a hang that
resulted from this race, but this introduced another race because the
URB callbacks could now be executed after snd_usb_hw_free() has
returned, and try to access already freed data.
Fix the first race by introducing a mutex to serialize the disconnect
callback and all PCM callbacks that manage URBs (hw_free and hw_params).
Reported-and-tested-by: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
Cc: <stable@kernel.org>
[CL: also serialize hw_params callback]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default WM8958 jack detection handler implements a full set of buttons
and also support for video detection. Support for multi-button jacks is
fairly system specific and will usually require some tuning for headsets
so simplify the implementation to only report a simple short to ground
button, leaving multi-button headsets to be handled by system specific
code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 has a different microphone bias architecture to WM8994 so needs
different configuration to WM8994. Support this in platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow direct routing of the WM8958 microphone detection signal to a GPIO
to be used, saving the need to demux the interrupt.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
As bias level changes can be quite time consuming and the bias changes
for multiple devices aren't strongly tied to each other (if anything it
can be advantageous to bring different devices up together) we can improve
the state transition time for multi-component systems by running the bias
level changes for all the devices in parallel. This is very simple to
achieve using the kernel async functionality so use that to schedule the
work.
This should have no practical effect for the overwhelming majority of
systems which have a single DAPM context - we'll bounce into another
thread to do the bias level change but otherwise everything will happen
in exactly the same order as it did before.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We can get the card from the DAPM context so don't bother passing it as
an argument.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The microphone detection functionality requires a clock to work. In any
non-detection case where the MICBIAS is enabled CLK_SYS will be needed
anyway so there is no negative impact on power consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: Ensure supplies are maintained for force enabled widgets
ASoC: WM8994: Improve playback robustness
ASoC: WM8994: Improve robustness in some use cases
ASoC: WM8903: Fix mic detection enable logic
ASoC: WM8903: Fix mic detection register definitions
ASoC: CX20442: fix wrong reg_cache_default content
ASoC: Sync initial widget state with hardware
This typo caused some microphone inputs not to be correctly
initialized on VIA codecs.
Reported-By: Mark Goldstein <goldstein.mark@gmail.com>
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Si4713 FM transmitter on Nokia RX-51/N900 is connected to same Line out
signals of TLV320AIC34 than TPA6130 headphone amplifier.
This patch adds route to transmitter and "FM Transmitter" control to keep
route active when needed.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch changes dependency of ARCH_EXYNOS4 from ARCH_S5PV310
according to the change of ARCH name, EXYNOS4.
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: HDA: Do not announce false surround in Conexant auto
ALSA: HDA: Conexant auto: Handle multiple connections to ADC node
ALSA: HDA: Add position_fix quirk for an Asus device
ALSA: caiaq - Fix possible string-buffer overflow
ALSA: au88x0 - Modify pointer callback to give accurate playback position
Add " Playback Volume" to 10 bands Equalizer Controls of au88x0 so that
alsa-lib won't regard them as "Capture Volume".
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without this patch, one line-out and one speaker and
Conexant's auto parser would announce (non-working) surround
capabilities.
BugLink: http://bugs.launchpad.net/bugs/721126
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conexant 20641 has several inputs to its ADC node, with one selector
and individual amps for all inputs. This patch adds support in the
Conexant auto parser to handle that case.
It also means that the pin node's volume is being renamed to "Boost"
to avoid name clash with the new volume controls on the ADC node.
BugLink: http://bugs.launchpad.net/bugs/719524
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make newly created AC97 emulation of azt3328 known to the AC97 layer
side.
- relocate common functions to the top (due to definition after use)
- rename control names
- adjust 3D settings to the card's custom layout of this register
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make use of the very flexible ALSA ac97 layer (hooks for custom I/O!)
on this weird AC97 copycat hardware,
via semi-extended I/O translation/emulation.
Some 5kB binary/loaded size saved (well... additional huge AC97 module
penalty not factored in, of course ;-P).
Given that the driver previously had 20kB that's not bad,
but the much more important thing is to have AC97 layer stress-tested
with a thoroughly weird AC97 copycat (or, simply put, if it were not for
this AC97 test aspect, this effort would merely have been a nut job ;).
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The microphone detection functionality requires a clock to work. In any
non-detection case where the MICBIAS is enabled CLK_SYS will be needed
anyway so there is no negative impact on power consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some systems wish to use jacks as wake sources. Provide a wake flag in the
GPIO configuration which causes the driver to enable the IRQ as a wake
source.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The only thing that should ever be calling this is soc-core and that is
built as part of the same module so doesn't need the export.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use AC97 macros (sometimes already existing, or newly added)
instead of error-prone repetition of open-coded values.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pulseaudio doesnt work with current driver and it was root caused to absense of
hw_params function and malloc_pages in it.
This patch adds this and allows pa to work fine with these drivers
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch removes the old method of soc-audio device creation in mfld machine
and makes use of new soc_register_card API to register the card
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The tlv scale is defined as (min, step, mute). The mute is not supported here so
put the value to 0
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch makes the DMIC dynamically connect to TX Mux, earlier code had
erroneously made this as static path
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch makes the codec playback rails (headset and speaker) depend on
actual pins they control. This enables better power management of the codec
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is more usefull to report headset instead of video out cable in response
to jack insertion as this is more usual use-case and because now the headset
feature is supported. Automatic accessory detection is not possible at the
moment so most sensible static accessory type have to be used.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for headset microphone in Nokia RX-51/N900. The mic
signal from audio jack is routed to codec A LINE1L via two switches and the
mic bias is coming from codec B part.
First switch is the tv-out switch that is already supported and the second
switch selects between voltage detection circuit and codecs. As there is
no use for voltage detection at the moment the second switch is connected
statically to codecs in rx51_soc_init.
Headset can be active when control "Jack Function" is set to "Headset".
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Just slight cleanup to be sync with upcoming change.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The bug reporter claims that position_fix=1 is needed for his
microphone to work. The controller PCI vendor-id is [1002:4383] (rev 40).
Reported-by: Kjell L.
BugLink: http://bugs.launchpad.net/bugs/718402
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use strlcpy() to assure not to overflow the string array sizes by
too long USB device name string.
Reported-by: Rafa <rafa@mwrinfosecurity.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The number of cases has increased so use switch-case rather than
if-statements.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The MK2 generation of Native Instruments' sound cards are in fact
compliant to the USB audio standard of version 2 and other approved USB
standards. However, they come up as vendor-specific device when first
connected but can be told to come up with a new set of descriptors
upon their next enumeration. The interfaces announced by the new
descriptors will be handled by the kernel's class drivers. This is done
by issuing a vendor specific device request and sending the device to
reset.
There are also some vendor-specific USB requests for some mixer elements
that can't be exported in a standard compliant way. The driver now
supports them with quirks handling mechanisms.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the core code where sparse complains. In most cases, this means
just adding annotations to confirm that we indeed want to do the dirty
things we're doing.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8903 interrupts are clear on read so if the WM8903 detection is
enabled from platform data when the IRQ is in use (rather than using a
direct signal from a GPIO) status may be lost during startup. Help users
spot this misconfiguration by adding a WARN_ON().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
With the appropriate MODULE_ALIAS in place, the audio modules will be
automatically loaded; there is no longer a need for manual modprobes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Harmony has both an external mic (a regular mic jack) and an internal mic
(a 0.1" two-pin header on the board).
The external mic is connected to the WM8903's IN1L pin, and is supported
by the current driver.
The internal mic is connected to the WM8903's IN1R pin, and is not supported
by the current driver.
It appears that no Harmony systems were shipped with any internal mic
connected; users were expected to provide their own. This makes the
internal mic connection less interesting.
The WM8903's Mic Bias signal is used for both of these mics. For each mic,
a GPIO drives a transistor which gates whether the mic bias signal is
actively connected to that mic, or isolated from it.
The dual use of the mic bias for both mics makes a general-purpose complete
implementation of mic detection using the mic bias complex. So, for
simplicity, the internal mic is currently ignored by the driver.
This patch configures the relevant GPIOs to enable the mic bias connection
to the external mic, and disable the mic bias connection to the internal
mic. Note that in practice, this is the default state if these GPIOs aren't
configured.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* Add jack definition for mic jack
* Request wm8903 to enable mic detection
* Force mic bias on, since it's required for mic detection
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a widget has been force enabled then not only do we need to keep the
widget itself enabled, we also need to keep any supplies the widget
requires enabled. The user could force all the individual widgets on but
this requires too much knowledge of device internals.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
On WM8994 revision D and earlier ensure proper playback robustness
as some rare use cases can trigger issues.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Ensure that on disabling certain registers such as AIF1DAC1L,
AIF1DAC1R etc. the AIF1CLK and AIF2CLK remain enabled. Similarly
when enabling those registers, AIF1CLK and AIF2CLK will remain
disabled.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The mic detection HW should be enabled when either mic or short detection
is required, not when only both are required.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - add quirk for Ordissimo EVE using a realtek ALC662
ALSA: hrtimer: remove superfluous tasklet invocation
ALSA: hrtimer: handle delayed timer interrupts
ALSA: HDA: Add subwoofer quirk for Acer Aspire 8942G
ALSA: hda - Don't handle empty patch files
ALSA: hda - Fix missing CA initialization for HDMI/DP
ALSA: usbaudio - Enable the E-MU 0204 USB
ALSA: hda - switch lfe with side in mixer for 4930g
ASoC: Improve WM8994 digital power sequencing
ASoC: Create an AIF1ADCDAT signal widget to match AIF2
asoc: davinci: da830/omap-l137: correct cpu_dai_name
ASoC: fill in snd_soc_pcm_runtime.card before calling snd_soc_dai_link.init()
It is safe to use sleeping gpio in snd_soc_jack_gpio_detect as it is not
called from interrupt context. This avoids WARN_ON from __gpio_get_value
if sleeping gpio is registered for jack.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch modifies the mfld_machine to use the new jack apis for adding the
voltage zones for jack type detection. It also modifed TI sn95031 codec driver
to use these new apis
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This makes no real difference compared to the write sequencer sequence
that was previously used but can run without a clock being provided.
Also remove the write sequencer support code as this was the last use
of it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The write sequencer sequencer sequence takes longer than is desirable
as it brings up a full playback path which is not required at this
point. Open coding the sequence cuts the startup time by two thirds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Content of the CX20442's snd_soc_codec_driver.reg_cache_default pointed
area, introduced with my recent NULL pointer dereferece fix (commit
f019ee5feb), occured wrong after further
testing, more thorough than just booting successfully. There are two
problems with it:
1) It should read
(1 << CX20442_TELOUT) | (1 << CX20442_MIC),
not
CX20442_TELOUT | CX20442_MIC.
2) While correctly matching actual codec hardware state on boot when
fixed per 1), a few more code modifications would still be required
to reflect that state not only into register cache, but also force
them into DAPM pins state, otherwise an inconsitency occures which
may prevent further codec state changes from being applied correctly.
As a result, the phone stops ringing after reboot, until someone
picks up the handset for the first time.
Revert that reg_cache_default content to a working, previous de facto
default value of 0, in hope this change can still be accepted as an rc
cycle fix.
Created and tested against linux-2.6.38-rc4
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This netbook has a only one jack output and an internal mic.
By default, mic and jack sense aren't working. Using lenovo-101e
parameters makes both work.
The device seems based on a Sharetronic Q70, so this should fix audio for
this model too.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit bb758e9637 removed snd_hrtimer_callback() from the hardware
interrupt handler, thus moving it into a tasklet, but did not tell the
ALSA timer framework about this, so the timer handling would now be done
in the ALSA timer tasklet scheduled from another tasklet.
To fix this, add the flag to tell the ALSA timer framework that the
timer handler is already being invoked in a tasklet.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a timer interrupt was delayed too much, hrtimer_forward_now() will
forward the timer expiry more than once. When this happens, the
additional number of elapsed ALSA timer ticks must be passed to
snd_timer_interrupt() to prevent the ALSA timer from falling behind.
This mostly fixes MIDI slowdown problems on highly-loaded systems with
badly behaved interrupt handlers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Difference in major.minor between driver and firmware is an error now.
Release version mismatch give a warning.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Interrupt flag used for message handshake will be required for
stream interrupts, so conditionally compiled code without
HPI6205_NO_HSR_POLL defined can never be used; removing it.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Create and use HPI_ERROR_DSP_COMMUNICATION _DSP_BOOTLOAD, rather than
backend-specific error codes (now returned as data with the error).
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
asihpi.c don't link playback and capture streams, there is too much
offset between them.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some error codes had duplicate meanings. Just use one.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reported samples_played from card may be inaccurate, so don't use it.
Update control names to be closer to alsa standard practice.
Also fixed some accidentally lowercased strings.
[Removed adriver.h inclusion for external module builds by tiwai]
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove many unused functions.
Update some message and cache structs.
Use pci info directly from pci_dev.
Allow control cache elements with variable size, and handle
large message/response from dsp.
hpi6000 and hpi6205: fix error path when adapter bootload fails.
hpimsgx.c get rid of code duplicated in hpicmn.c
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Log HPI messages and responses in consistent numeric format,
which can be post-processed to get strings.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the reporter, node 0x15 needs to be muted for subwoofer
to stop sounding. This pin is marked as unused by BIOS, so fix that.
BugLink: http://bugs.launchpad.net/bugs/715877
Cc: stable@kernel.org (2.6.37+)
Reported-by: Hans Peter
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When an empty string is passed to patch option, the driver should
ignore it. Otherwise it gets an error by trying to load it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Explicitly cache the DC servo offsets for digital paths in the driver,
allowing them to be preserved over suspend and resume, and ensure that
we recalibrate analogue outputs paths when they are in use so that we
cover any changes in the input offset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds soc-jack support for adding voltage zones and for
detecting jack type
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC generally uses the register defaults for everything, but in some
cases the hardware will default to enabling some of the DAPM widgets
(clocks for example). Ensure that DAPM knows about the actual widget
state at initialisation by reading the enable bits after instantiating
the widgets so they don't get left enabled needlessly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8903 register map does not mute the DAC by default at startup
so we need to explicitly do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This simplfies the code and slightly reduces the startup time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
It causes noisy -codecs to appear in things like .codec_name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch modifies the Davinci i2s and mcasp drivers to make use of
ioremap() instead of IO_ADDRESS()
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In case of any error in probe() function, clk_disable() and clk_put()
should be called if clk_enable() and clk_get() went through.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch modifies the Davinci i2s and mcasp drivers
to make use of the resource_size() helper function for readability.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support to read the mic bias voltage
when a jack is inserted. It uses ADC to measure.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for registering jack interupt
and registering jack with core
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for jack detection and reporting in the codec
It however is not fully functional as it doesn't measure adc to figure
out what got inserted which will be added later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit 53d7d69d8f
ALSA: hdmi - support infoframe for DisplayPort
dropped the initialization of CA field accidentally.
This resulted in only two-channel LPCM mode on Nvidia machines.
Reference: kernel bug 28592
https://bugzilla.kernel.org/show_bug.cgi?id=28592
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
The patch c358e640a6 "ASoC: soc-cache: Add trace event for
snd_soc_cache_sync()" introduced a dereference of "codec->cache_ops"
before we had checked it for NULL.
I pulled the check forward, and then pulled everything in an indent
level.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move Chip Select control out of the CODEC code for CS4271.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
rt->rate is an unsigned char so it's never equal to -1. It's not a huge
problem because the invalid rate is caught inside the call to
usb6fire_pcm_set_rate() which returns -EINVAL. But if we fix the test
then it prints out the correct error message so that's good.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The AACI TRM requires the MAINCR enable bit to be held zero for two
bitclk cycles plus three apb_pclk cycles. Use a delay of 1us to
ensure this.
Ensure that writes to MAINCR to change the addressed codec only happen
when required, and that they take effect in a similar manner to the
above, otherwise we seem to occasionally have stuck slot busy bits.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Built-in sub-woofer can now be controlled by lfe slider instead of
side slider on Acer Aspire 5930g
Signed-off-by: Łukasz Wojniłowicz <lukasz.wojnilowicz@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The wm8753 codec supports switching between different DAI modes.
The current drivers tries to implement this by changing the DAI driver at
runtime. But to properly work this would require support from the ASoC core.
So this patch takes a different approch on how the DAI mode switching is
implemented.
The only difference, from a driver point of view, between the different DAI modes
is how to program the DAI format to the hardware. So what this patch is, it
stores the current format for each DAI in the drivers private struct and when
the DAI mode is changed the format gets simply reprogrammed according to the
new DAI mode.
Futhermore this patch restricts the changing of the DAI format to when the
codec is inactive.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: use linux/io.h to fix compile warnings
ALSA: hda - Fix memory leaks in conexant jack arrays
ASoC: CX20442: fix NULL pointer dereference
ASoC: Amstrad Delta: fix const related build error
ALSA: oxygen: fix output routing on Xonar DG
sound: silent echo'ed messages in Makefile
ASoC: Fix mask/val_mask confusion snd_soc_dapm_put_volsw()
ASoC: DaVinci: fix kernel panic due to uninitialized platform_data
ALSA: HDA: Fix microphone(s) on Lenovo Edge 13
ASoC: Fix module refcount for auxiliary devices
ALSA: HDA: cxt5066 - Use asus model for Asus U50F, select correct SPDIF output
ALSA: HDA: Add a new model "asus" for Conexant 5066/205xx
ALSA: HDA: Refactor some redundant code for Conexant 5066/205xx
On WM8994 revision D and earlier ensure optimal sequencing with
simultaneous usage of AIF1 and AIF2 by tying the signals together
so if paths through both are connected the streams are started
simultaneously.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
Due to the different routing for AIF1 and AIF2 we weren't using a
single widget to represent the ADCDAT signal. For consistency add
one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
McASP1 is used on the DA830/OMAP-L137 platform for the codec.
This is different from the DA850/OMAP-L138 platform which uses McASP0.
This is fixed by adding a new snd_soc_dai_link struct.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The .card member of the snd_soc_pcm_runtime structure pointed to by the
snd_soc_dai_link.init() argument used to be initialized before the
function being called. This has changed, probably unintentionally,
after recent refactorings. Since the function implementations are free
to make use of this pointer, move its assignment back before the
function is called to avoid NULL pointer dereferences.
Created and tested on Amstrad Delta againts linux-2.6.38-rc2
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For some codecs with large register maps, it was not possible to dump
all registers via the codec_reg file but only up to PAGE_SIZE bytes.
This patch fixes this problem.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For helping to reduce Greert's regression list...
src/sound/drivers/mtpav.c: error: implicit declaration of function 'inb'
src/sound/drivers/mtpav.c: error: implicit declaration of function 'outb'
...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Conexant codec driver adds the jack arrays in init callback which
may be called also in each PM resume. This results in the addition of
new jack element at each time.
The fix is to check whether the requested jack is already present in
the array.
Reference: Novell bug 668929
https://bugzilla.novell.com/show_bug.cgi?id=668929
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the format of the codec_reg file more easily parsable. Remove
the header field which gives the codec name. These changes are important
when it comes to extend the debugfs codec_reg file to dump more than
PAGE_SIZE bytes to make it easier to calculate offsets within the
file.
We still need to handle the case when the snd_soc_read() call fails
and <no data: %d> is outputted.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The CX20442 codec driver never provided the snd_soc_codec_driver's
.reg_cache_default member. With the latest ASoC framework changes, it
seems to be referred unconditionally, resulting in a NULL pointer
dereference if missing. Provide it.
Created and tested on Amstrad Delta against linux-2.6.38-rc2
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Amstrad Delta ASoC driver used to override the digital_mute()
callback, expected to be not provided by the on-board CX20442 CODEC
driver, with its own implementation. While this is still posssible when
substituting the whole empty snd_soc_dai_driver.ops member (the CX20442
case), replacing snd_soc_dai_ops.digital_mute only is no longer correct
after the snd_soc_dai_driver.ops member has been constified, and results
in build error.
Drop this actually not used code path in hope the CX20442 driver never
provides its own snd_soc_dai_ops structure.
Created and tested against linux-2.6.38-rc2
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
gpio_set_value* should accept logic values not just 0 or 1. The WM8903 GPIO
driver has been fixed to work this way, so remove the redundant !!
previously required when it didn't accept values >1.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Earphone in Nokia RX-51/N900 is connected to left HP output of B part of the
TLV320AIC34 dual codec. In RX-51 the codec A is used as a traditional codec
and the codec B as an auxiliary device.
Audio from codec A goes via the codec B to earphone:
MONO_LOUT of A -> LINE2R of B (B interconnects) -> HPLOUT of B -> Earphone.
Take earphone into use by utilizing the recent ASoC auxiliary and
cross-device support.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
