This patch replaces net_device arguments to mac80211 internal functions
with ieee80211_{local,sub_if_data} as appropriate.
It also does the same for many 802.11s mesh functions, and changes the
mesh path table to be indexed on sub_if_data rather than net_device.
If the mesh part needs to be a separate patch let me know, but since
mesh uses a lot of mac80211 functions which were being converted anyway,
the changes go hand-in-hand somewhat.
This patch probably does not convert all the functions which could be
converted, but it is a large chunk and followup patches will be
provided.
Signed-off-by: Jasper Bryant-Greene <jasper@amiton.co.nz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we deal with mesh forwarding before the 802.11->802.3 conversion, thus
eliminating a few unnecessary steps. The next hop lookup is called from
ieee80211_master_start_xmit() instead of subif_start_xmit(). Until the next hop
is found, RA in the frame will be all zeroes for frames originating from the
device. For forwarded frames, RA will contain the TA of the received frame,
which will be necessary to send a path error if a next hop is not found.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old infrastructure was:
- the default algorithm is built into mac80211
- other algorithms get into their own modules
The implementation of this complicated scheme was horrible
(just look at net/mac80211/Makefile), and anyone adding a new
algorithm would most likely not get it right at his first attempt.
This patch therefore builds all enabled algorithms into the mac80211
module.
The user interface for the rate control algorithms changes as follows:
- first the user can choose which algorithms to enable (currently only
MAC80211_RC_PID is available)
- if more than one algorithm is enabled (currently not possible since
only one algorithm is present) the user then chooses the default one
Note:
- MAC80211_RC_PID is always enables for CONFIG_EMBEDDED=n
Technical changes:
- all selected algorithms get into the mac80211 module
- net/mac80211/Makefile can now become much less complicated
- support for rc80211_pid_algo.c being modular is no longer required
- this includes unexporting mesh_plink_broken
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case the hash grow failed, it is not fair to return error -
the new node _was_ _actually_ added in this case.
Besides, after my previous patch, this grow is more likely
to fail on large hashes.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mesh_path_node_copy() can be called like this:
mesh_path_add
`- write_lock(&pathtbl_resize_lock); /* ! */
`- mesh_table_grow
`- ->copy_node
`- mesh_path_node_copy
thus, the GFP_KERNEL is not suitable here.
The acceptable fix, I suppose, is make this allocation GPF_ATOMIC -
the mpath_node being allocated is 4 pointers, i.e. this allocation
is small enough to survive even under a moderate memory pressure.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now - return the -ENOMEM in case kmalloc fails.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mesh_path_node_copy() performs kmalloc() and thus - may fail
(well, it does not now, but I'm fixing this right now). Its caller -
the mesh_table_grow() - isn't prepared for such a trick yet.
This preparation is just flush the new hash and make copy_node()
return an int value.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(This set applies OK without the previous one of 4 patches,
but with some fuzz in the 7th one)
The mesh_path_node_free() does so under hashwlock.
But, this one is called
1. from mesh_path_add() after an old hash is hidden and
synchronize_rcu() is calld
2. mesh_pathtbl_unregister(), when the module is being
unloaded and no devices exist to mess with this hash.
So, it seems to me, that simply removing the call is OK.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are already tree paths, that do incremental rollbacks, so
merge them together, rename labels and format the code to look a
bit nicer.
(I do not mind dropping/delaying this patch however).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling synchronize_rcu() under write-lock-ed pathtbl_resize_lock may
result in this warning (and other side effects).
It looks safe just dropping this lock before calling synchronize_rcu.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new_node kmallocation is not checked for success, so add
this check.
BTW, it also happens under the read_lock.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mesh_path_add() read-locks the pathtbl_resize_lock and calls
kmalloc with GFP_KERNEL mask.
Fix it and move the endadd2 label lower. It should be _before_ the
if() beyond, but it makes no sense for it being there, so I move it
right after this if().
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip properly entries whose dev does not match.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Postponing the deletion is not really useful anymore.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids dereferencing a no longer existing struct mesh_path.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis pointed out that this path is going to be freed right
away anyway so there's no point in assigning next_hop.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes access to the STA hash table/list use RCU to protect
against freeing of items. However, it's not a true RCU, the
copy step is missing: whenever somebody changes a STA item it
is simply updated. This is an existing race condition that is
now somewhat understandable.
This patch also fixes the race key freeing vs. STA destruction
by making sure that sta_info_destroy() is always called under
RTNL and frees the key.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This needs to be exported because rate control algorithms
can be modular.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mesh path table associates destinations with the next hop to reach them. The
table is a hash of linked lists protected by rcu mechanisms. Every mesh path
contains a lock to protect the mesh path state.
Each outgoing mesh frame requires a look up into this table. Therefore, the
table it has been designed so it is not necessary to hold any lock to find the
appropriate next hop.
If the path is determined to be active within a rcu context we can safely
dereference mpath->next_hop->addr, since it holds a reference to the sta
next_hop. After a mesh path has been set active for the first time it next_hop
must always point to a valid sta. If this is not possible the mpath must be
deleted or replaced in a RCU safe fashion.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
