Extend the tca6416 driver to use enable_irq_wake() and disable_irq_wake()
in the suspend/resume hooks.
This makes it possible to wake up from suspend-to-ram using a tca6416 key
on the sh7372 mackerel board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The AT42QT1070 QTouch sensor supports up to 7 keys.
The driver has been tested on Atmel AT91SAM9M10-G45-EK board, and it
should work fine on other platforms.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The MCS50XX series has a HW bug that requires explicit chip power down.
If chip is not powered down before shutting the system down the control
pins (powerup, interrupt) are pulled up and residue current continues
flowing into the chips making them continue consuming power.
Signed-off-by: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds support for system-level suspend/resume to the driver.
Signed-off-by: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Enable Runtime PM functionality in OMAP4 driver based on the following
assumptions:
- keyboard controller in wakeup domain so it is always on and power
impact is minimal;
- in OMAP4 the device control is at module/device level and ick/fclk
level control is difficult so cutting of clocks will prevent
interrupts.
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move to convert drivers to use dev_pm_ops rather than
bus specific ops to facilitate core work. Do this conversion for max7359.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move away from bus specific PM operations to using
dev_pm_ops in order to facilicate core improvements. Update lm8323 to
the new model.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add Fn keymap support to allow for internal processing of Fn keys.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - pass touch resolution to clients through input_absinfo
Input: wacom - add 2 Bamboo Pen and touch models
Input: sysrq - ensure sysrq_enabled and __sysrq_enabled are consistent
Input: sparse-keymap - fix KEY_VSW handling in sparse_keymap_setup
Input: tegra-kbc - add tegra keyboard driver
Input: gpio_keys - switch to using request_any_context_irq
Input: serio - allow registered drivers to get status flag
Input: ct82710c - return proper error code for ct82c710_open
Input: bu21013_ts - added regulator support
Input: bu21013_ts - remove duplicate resolution parameters
Input: tnetv107x-ts - don't treat NULL clk as an error
Input: tnetv107x-keypad - don't treat NULL clk as an error
Fix up trivial conflicts in drivers/input/keyboard/Makefile due to
additions of tc3589x/Tegra drivers
This patch adds support for the internal matrix keyboard controller for
Nvidia Tegra platforms.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver does not require hardirq context and can work with threaded
interrupts as well, so let's switch to request_any_context_irq which
will select the context that is available for us.
Signed-off-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should use IS_ERR() when checking whether clk_get() succeeded or
not since it returns errors by encoding error codes with ERR_PTR().
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The only platform using this driver (mach-aaec2000) is no longer in
the kernel so remove the driver.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (58 commits)
Input: wacom_w8001 - support pen or touch only devices
Input: wacom_w8001 - use __set_bit to set keybits
Input: bu21013_ts - fix misuse of logical operation in place of bitop
Input: i8042 - add Acer Aspire 5100 to the Dritek list
Input: wacom - add support for digitizer in Lenovo W700
Input: psmouse - disable the synaptics extension on OLPC machines
Input: psmouse - fix up Synaptics comment
Input: synaptics - ignore bogus mt packet
Input: synaptics - add multi-finger and semi-mt support
Input: synaptics - report clickpad property
input: mt: Document interface updates
Input: fix double equality sign in uevent
Input: introduce device properties
hid: egalax: Add support for Wetab (726b)
Input: include MT library as source for kerneldoc
MAINTAINERS: Update input-mt entry
hid: egalax: Add support for Samsung NB30 netbook
hid: egalax: Document the new devices in Kconfig
hid: egalax: Add support for Wetab
hid: egalax: Convert to MT slots
...
Fixed up trivial conflict in drivers/input/keyboard/Kconfig
There was a semi-colon missing and it broke the compile.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (243 commits)
omap2: Make OMAP2PLUS select OMAP_DM_TIMER
OMAP4: hwmod data: Fix alignment and end of line in structurefields
OMAP4: hwmod data: Move the DMA structures
OMAP4: hwmod data: Move the smartreflex structures
OMAP4: hwmod data: Fix missing SIDLE_SMART_WKUP in smartreflexsysc
arm: omap: tusb6010: add name for MUSB IRQ
arm: omap: craneboard: Add USB EHCI support
omap2+: Initialize serial port for dynamic remuxing for n8x0
omap2+: Add struct omap_board_data and use it for platform level serial init
omap2+: Allow hwmod state changes to mux pads based on the state changes
omap2+: Add support for hwmod specific muxing of devices
omap2+: Add omap_mux_get_by_name
OMAP2: PM: fix compile error when !CONFIG_SUSPEND
MAINTAINERS: OMAP: hwmod: update hwmod code, data maintainership
OMAP4: Smartreflex framework extensions
OMAP4: hwmod: Add inital data for smartreflex modules.
OMAP4: PM: Program correct init voltages for scalable VDDs
OMAP4: Adding voltage driver support
OMAP4: Register voltage PMIC parameters with the voltage layer
OMAP3: PM: Program correct init voltages for VDD1 and VDD2
...
Fix up trivial conflict in arch/arm/plat-omap/Kconfig
Add support for the keypad controller module found on the
TC3589X devices. This driver default adds the support for
TC35893 device.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
[Some minor fixups for compilation]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Most keypad drivers make use of the <linux/input/matrix_keypad.h>
defined macros, structures and inline functions.
Convert omap-keypad driver to use those as well, as suggested by a
compile time warning, hardcoded into the OMAP <palt/keypad.h>.
Created against linux-2.6.37-rc5.
Tested on Amstrad Delta.
Compile tested with omap1_defconfig and omap2plus_defconfig shrinked to
board-h4.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The existing gpio-keys driver can be usable only for GPIO lines with
interrupt support. Several devices have buttons connected to a GPIO
line which is not capable to generate interrupts. This patch adds a
new input driver using the generic GPIO layer and the input-polldev
to support such buttons.
[Ben Gardiner <bengardiner@nanometrics.ca: fold code to use more
of the original gpio_keys infrastructure; cleanups and other
improvements.]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Many of the IBM Terminal keyboards from the 1980s and early 1990s communicate
using a protocol similar, but not identical to the AT keyboard protocol.
(Models known to be like this include 6110344, 6110668, 1390876, 1386887, and
possibly others.)
When the connector is rewired or adapter to an AT-DIN or PS/2 connector, they
can be connected to a standard PC, with three caveats:
a) They can only use scancode set 3; requests to use anything else are
quietly ignored.
b) The AT Command to request Make, Break and Repeat codes is not properly
interpreted.
c) The top function keys on a 122 key keyboard, and the arrow/edit keys in
the middle of the board send non-standard scancodes.
C) is easily taken care of in userspace, by use of setkeycodes
B) can be taken care of by a userspace hack (that makes the kernel complain
in dmesg)
A) is fixable in theory, but on the keyboard i tested on (6110668), it seems
to be detected unoverridably as Set 2, causing userspace oddities that make
it harder to fix C).
Enclosed is a small patch to the kernel that fixes A) and B) in the kernel,
making it much easier to fix C) in userspace. It adds a single kernel
command line parameter that overrides the detection that sets these boards
as set 2, and instead of sending the Make-break-repeat command to the
keyboard, it sends the make-break command, which is properly recognized by
these keyboards. Software level key repeating seems to make up for the lack
of hardware repeat codes perfectly.
Without manually setting the command line parameter (tentatively named
atkbd.terminal), this code has no effect, and the driver works exactly as
before.
See also:
http://www.seasip.info/VintagePC/ibm_1390876.htmlhttp://www.seasip.info/VintagePC/ibm_6110344.htmlhttp://geekhack.org/showwiki.php?title=Island:7306
Signed-off-by: Erika Quinn <erikas.aubade@gmail.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Unify adp5588-gpio and adp5588-keys common header defines (as per Andrew
Morton request). For consistency, move remaining defines and prefix
accordingly.
No functional changes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
davinci: fix remaining board support after io_pgoffst removal
davinci: mityomapl138: make file local data static
arm/davinci: remove duplicated include
davinci: Initial support for Omapl138-Hawkboard
davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
davinci: add tnetv107x touchscreen platform device
input: add driver for tnetv107x touchscreen controller
davinci: add keypad config for tnetv107x evm board
davinci: add tnetv107x keypad platform device
input: add driver for tnetv107x on-chip keypad controller
net: davinci_emac: cleanup unused cpdma code
net: davinci_emac: switch to new cpdma layer
net: davinci_emac: separate out cpdma code
net: davinci_emac: cleanup unused mdio emac code
omap: cleanup unused davinci mdio arch code
davinci: cleanup mdio arch code and switch to phy_id
net: davinci_emac: switch to new mdio
omap: add mdio platform devices
davinci: add mdio platform devices
net: davinci_emac: separate out davinci mdio
...
Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)
KBUILD_MODNAME normalizes "-" to "_". This is non-obvious and results in
the id name for ADP5588 being "adp5588_keys" while the other supported id
is "adp5587-keys". So avoid this define and use an explicit string as the
id name.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Program keyboard controller to generate a wake-up request on events and
on long key presses. It will not generate wake-up requests on timeouts
since driver code does not handle them.
This allows keyboard to wake-up OMAP from suspend.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove SYSCONFIG register configuration, omap hwmod framework will
use internal API to modify as required.
Other minor updates:
- Change a variable name from DEF to VAL, this represents a value
- Break line width to 80 characters
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Get mem and irq resources using platform helpers
- platform_get_base
- platform_get_irq
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for the keypad controller in the Scroll Key Encoder (SKE)
module on the Nomadik family and the DB8500 SoC.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should not try to call free_irq() when request_irq() failed.
Reported-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
mach-mmp needs to clear wake event in order to clear the keypad interrupt
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
mach-mmp utilizes pxa27x_keypad code so we need to move header to
platform pxa directory.
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
