This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c,
and exports the functions to be used by xHCI driver later.
AMD PLL quirk disable the optional PM feature inside specific
SB700/SB800/Hudson-2/3 platforms under the following conditions:
1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
Without AMD PLL quirk, USB isochronous stream may stutter or have breaks
occasionally, which greatly impair the performance of audio/video streams.
Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be
added to xHCI driver too. They are doing similar things actually, so move
the quirk code to pci-quirks.c, which has several advantages:
1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and
make them cleaner;
2. AMD chipset information will be probed only once and then stored.
Currently they're probed during every OHCI/EHCI initialization, move
the detect code to pci-quirks.c saves the repeat detect cost;
3. Build up synchronization among OHCI/EHCI/xHCI driver. In current
code, every host controller enable/disable PLL only according to
its own status, and may enable PLL while there is still isoc transfer on
other HCs. Move the quirk to pci-quirks.c prevents this issue.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ehci and ohci drivers are simplified; Since
UHH and TLL initialization, clock handling are
done by common usbhs core driver, these functionalities
are removed from ehci and ohci drivers.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Create the ehci and ohci specific platform data structures.
The port enum values are made common for both ehci and ohci.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that we have names on all memory bases, we can
switch to use platform_get_resource_byname() which
will make it simpler when we move to a setup where
OHCI and EHCI on OMAP play well together.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The EHCI controller in OMAP4 supports a transceiver-less link
mode (TLL mode), similar to the one in OMAP3. On the OMAP4
however, there are an additional set of clocks that need
to be turned on to get this working.
Request and configure these for each port if that port
is connected in TLL mode.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove redundant "toggle" member from struct isp1760_qtd, and store toggle
status in struct isp1760_qh only.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace the period calculation for INT packets with something readable. Seems
to fix a rare bug with quickly repeated insertion/removal of several USB
devices simultaneously (hub control INT packets).
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Consolidate printouts to use dev_XXX functions instead of an assortment of
printks and driver specific macros. Remove some unused code snippets and struct
members. Remove some unused function parameters and #defines. Change the
"queue_entry" variable name which has different but related meanings in
different places and use "slot" only.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes the redundant hw_next list pointer from struct isp1760_qtd, removes some
unused #defines, removes redundant "urb" member from struct inter_packet_info.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This helps users with platform-bus-connected isp176xs, big-endian cpu,
and missing byteswapping on the data bus. It does so by collecting all
SW byteswaps in one place and also fixes a bug with non-32-bit io
transfers on this hardware, where payload has to be byteswapped
instead of ptds.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Patch below removes one to many "n's" in a word..
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get rid of users of of_platform_driver in drivers/usb. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch add bus glue for USB controller commonly found in PMC-Sierra MSP71xx family of SoC's.
Signed-off-by: Anoop P A <anoop.pa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following compile warnings
drivers/usb/host/ehci-dbg.c:45: warning: 'dbg_hcs_params' defined but not used
drivers/usb/host/ehci-dbg.c:89: warning: 'dbg_hcc_params' defined but not used
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a device plug/unplug is detected on an ATI SB700 USB controller in D3,
it appears to set the port status register but not the controller status
register. As a result we'll fail to detect the plug event. Check the port
status register on resume as well in order to catch this case.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable <stable@kernel.org> [after .39-rc1 is out]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Functions that are not used outsde of the module they are defined
should be marked as static.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
There is no point in casting to (void *) when setting up xhci->ir_set
as it only makes us lose __iomem annotation and makes sparse unhappy.
OTOH we do need to cast to (void *) when calculating xhci->dba from
offset, but since it is IO memory we need to annotate it as such.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xhci->ir_set points to __iomem region, but xhci_print_ir_set accepts
plain struct xhci_intr_reg * causing multiple sparse warning at call
sites and inside the fucntion when we try to read that memory.
Instead of adding __iomem qualifier to the argument let's rework the
function so it itself gets needed register set from xhci and prints
it.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The expression
while (running_total < sg_dma_len(sg))
does not take into account that the remaining data length can be less
than sg_dma_len(sg). In that case, running_total can end up being
greater than the total data length, so an extra TRB is counted.
Changing the expression to
while (running_total < sg_dma_len(sg) && running_total < temp)
fixes that.
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Calculations like
running_total = TRB_MAX_BUFF_SIZE -
(sg_dma_address(sg) & (TRB_MAX_BUFF_SIZE - 1));
if (running_total != 0)
num_trbs++;
are incorrect, because running_total can never be zero, so the if()
expression will never be true. I think the intention was that
running_total be in the range of 0 to TRB_MAX_BUFF_SIZE-1, not 1
to TRB_MAX_BUFF_SIZE. So adding a
running_total &= TRB_MAX_BUFF_SIZE - 1;
fixes the problem.
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
This makes it easier to spot some problems, which will be fixed by the
next patch in the series. Also change dev_dbg to dev_err in
check_trb_math(), so any math errors will be visible even when running
with debug disabled.
Note: This patch changes the expressions containing
"((1 << TRB_MAX_BUFF_SHIFT) - 1)" to use the equivalent
"(TRB_MAX_BUFF_SIZE - 1)". No change in behavior is intended for
those expressions.
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Change the BUGs in xhci_find_new_dequeue_state() to WARN_ONs, to avoid
bringing down the box if one of them is hit
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Use bitmap_set()/bitmap_clear() to fill/zero a region of a bitmap
instead of doing set_bit()/clear_bit() each bit.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that ehci_run don't call ehci_reset, we can use ehci_run.
Signed-off-by: Matthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
TDI driver does the ehci_reset in their reset callback.
Don't reset in ehci_run because configuration settings done in
platform driver will be reset.
This will allow to make msm use ehci_run.
Signed-off-by: Matthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The document says:
|2.1 Problem description
| When at least two USB devices are simultaneously running, it is observed that
| sometimes the INT corresponding to one of the USB devices stops occurring. This may
| be observed sometimes with USB-to-serial or USB-to-network devices.
| The problem is not noticed when only USB mass storage devices are running.
|2.2 Implication
| This issue is because of the clearing of the respective Done Map bit on reading the ATL
| PTD Done Map register when an INT is generated by another PTD completion, but is not
| found set on that read access. In this situation, the respective Done Map bit will remain
| reset and no further INT will be asserted so the data transfer corresponding to that USB
| device will stop.
|2.3 Workaround
| An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can
| be implemented and if a certain Done bit is never set, verification of the PTD completion
| can be done by reading PTD contents (valid bit).
| This is a proven workaround implemented in software.
Russell King run into this with an USB-to-serial converter. This patch
implements his suggestion to enable the high frequent SOF interrupt only
at the time we have ATL packages queued. It goes even one step further
and enables the SOF interrupt only if we have more than one ATL packet
queued at the same time.
Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x]
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ehci_lpm_set_da and ehci_lpm_check are EHCI 1.1 specific functions which
are not used on many platforms but do generate annoying gcc warnings
Signed-off-by: Maksim Rayskiy <mrayskiy@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed to resolve some merge conflicts that were found
in the USB host controller patches, and reported by Stephen Rothwell.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit b7d5b439b7.
It conflicts with commit baab93afc2 "USB:
EHCI: ASPM quirk of ISOC on AMD Hudson" and merging the two just doesn't
work properly.
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The mxc-ehci driver calls SoC specific phy initialization right after
calling board specific initialization. To offer greater flexibility for
boards to setup the phy and to get rid of some unnecessary flags in
platform data this patch lets the boards call the SoC specific phy
initialization and remove it from the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes the below compilation errors.
CC drivers/usb/gadget/ci13xxx_msm.o
CC net/mac80211/led.o
drivers/usb/gadget/ci13xxx_msm.c: In function 'ci13xxx_msm_notify_event':
drivers/usb/gadget/ci13xxx_msm.c:42: error: 'USB_AHBBURST' undeclared (first use in this function)
drivers/usb/gadget/ci13xxx_msm.c:42: error: (Each undeclared identifier is reported only once
drivers/usb/gadget/ci13xxx_msm.c:42: error: for each function it appears in.)
drivers/usb/gadget/ci13xxx_msm.c:43: error: 'USB_AHBMODE' undeclared (first use in this function)
make[4]: *** [drivers/usb/gadget/ci13xxx_msm.o] Error 1
make[3]: *** [drivers/usb/gadget] Error 2
MSM USB driver is not supported on boards like trout (MSM7201) which
has an external PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The convention is to prefix symbols exported from the USB HCD core with
"usb_hcd". This change makes unmap_urb_setup_for_dma() and
unmap_urb_for_dma() consistent with that.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In create_companion_file() there is a bogus assignemt to i created for
the express purpose of avoiding an ignored return value warning.
With pre-release GCC-4.6, this causes a 'set but not used' warning.
Kick the problem further down the road by just returning i. All the
callers of create_companion_file() ignore its return value, so all is
good:
o No warnings are issued.
o We still subvert the desires of the authors of device_create_file()
by ignorning error conditions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With pre-release GCC-4.6, we get a 'set but not used' warning when
EHCI_URB_TRACE is not set because we set the qtd variable without
using it.
Rearrange the statements so that we only set qtd if it will be used.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vdbg macro is not used anywhere so it can be removed.
With pre-release GCC-4.6, there are several complaints of variables
that are 'set but not used' caused by the ehci_vdbg() macro expanding
to something that does not contain any of its arguments. We can quiet
this warning by rewriting ehci_vdbg() as a variadic static inline that
does nothing.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pre-release GCC-4.6 now correctly flags this code as dead.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c,
and exports the functions to be used by xHCI driver later.
AMD PLL quirk disable the optional PM feature inside specific
SB700/SB800/Hudson-2/3 platforms under the following conditions:
1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
Without AMD PLL quirk, USB isochronous stream may stutter or have breaks
occasionally, which greatly impair the performance of audio/video streams.
Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be
added to xHCI driver too. They are doing similar things actually, so move
the quirk code to pci-quirks.c, which has several advantages:
1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and
make them cleaner;
2. AMD chipset information will be probed only once and then stored.
Currently they're probed during every OHCI/EHCI initialization, move
the detect code to pci-quirks.c saves the repeat detect cost;
3. Build up synchronization among OHCI/EHCI/xHCI driver. In current
code, every host controller enable/disable PLL only according to
its own status, and may enable PLL while there is still isoc transfer on
other HCs. Move the quirk to pci-quirks.c prevents this issue.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-greg' of git://gitorious.org/usb/usb:
usb: ehci-omap: Show fatal probing time errors to end user
usb: musb: introduce api for dma code to check compatibility with usb request
usb: musb: maintain three states for buffer mappings instead of two
usb: musb: disable double buffering when it's broken
usb: musb: hsdma: change back to use musb_read/writew
usb: musb: core: fix IRQ check
usb: musb: fix kernel panic during s2ram(v2)
In drivers/usb/host/sl811-hcd.c::sl811h_urb_enqueue(), memory is allocated
with kzalloc() and assigned to 'ep'. If we leave via the 'fail' label due
to 'if (ep->maxpacket > H_MAXPACKET)', then 'ep' will go out of scope
without having been assigned to anything, so we'll leak the memory we
allocated.
This patch fixes the leak by simply calling kfree(ep); before jumping to
the 'fail' label.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a few error paths in ehci_hcd_omap_probe that can be triggered
because of memory allocation or hw failure. Change those dev_dbg error
prints to dev_err with an error code printed so that the end users are able
to notice the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
lh7a40x has only been receiving updates for updates to generic code.
The last involvement from the maintainer according to the git logs was
in 2006. As such, it is a maintainence burden with no benefit.
This gets rid of two defconfigs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-usb-linus' of master.kernel.org:/pub/scm/linux/kernel/git/sarah/xhci:
xhci: Remove more doorbell-related reads
xHCI: fix printk_ratelimit() usage
xHCI: replace dev_dbg() with xhci_dbg()
xHCI: fix cycle bit set in giveback_first_trb()
xHCI: remove redundant parameter in giveback_first_trb()
xHCI: fix queue_trb in isoc transfer
xhci: Use GFP_NOIO during device reset.
usb: Realloc xHCI structures after a hub is verified.
xhci: Do not run xhci_cleanup_msix with irq disabled
xHCI: synchronize irq in xhci_suspend()
xhci: Resume bus on any port status change.
commit 711669e5b8 fixed port 0 support
for i.MX51 but broke it for (at least) i.MX27 which doesn't have
a usb_phy1 clock but has a pdev->id 0.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previously a check was done on an ID register at the base of a CPU's
internal USB registers to determine if system interface regsiters were
present. The check looked for an ID register that had the format
ID[0:5] == ~ID[8:13] as described in the MPC5121 User's Manual to
determine if a MPC5121 or MPC83xx/85xx was being used.
There are two issues with this method:
- The ID register is not defined on the MPC83xx/85xx CPUs, so its
unclear what is being checked on them.
- Newer CPUs such as the P4080 also don't document the ID register, but
do share the same format as the MPC5121. Thus the previous code did
not set 'have_sysif_regs' properly which results in the P4080 not
properly initializing its USB ports.
Using the device tree 'compatible' node is a cleaner way to determine if
'have_sysif_regs' should be set and resolves the USB initialization issue
seen on the P4080.
Tested on a P4080-based system and compile tested on mpc512x_defconfig
with Freescale EHCI driver enabled.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1440) fixes a bug in ehci-hcd. ehci->periodic_size is
used to compute the size in a dma_alloc_coherent() call, but then it
gets changed later on. As a result, the corresponding call to
dma_free_coherent() passes a different size from the original
allocation. Fix the problem by adjusting ehci->periodic_size before
carrying out any of the memory allocations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
CC: David Brownell <david-b@pacbell.net>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AMD Hudson also needs the same ASPM quirk as SB800
Signed-off-by: Alex He <alex.he@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
