Add configuration callback for SPI bus 1 on GPD[8..10] and ensure the
correct GPIO configuration register definitions in regs-gpio.h
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the definition of the "generic" IRQ in the process.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the s3c_device_nand platform device from plat-s3c24xx to plat-s3c,
now that the nand driver also support the s3c64xx devices.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add debugfs support for the cpufreq driver to allow
information about the system state to be exported to
the user.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add armclk for use with the cpufreq support and anything
else that may want it. This clock is just a direct
descendant of fclk.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add board support for CPUFREQ with the Simtec BAST board
registering the necessary information with the core.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a sysdev S3C2410A sysdev to allow the differentiation
of the S3C2410A from the S3C2410. This is needed for the
CPUFREQ code to enable the extra features and update cpu
specific information.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the mapping of the memory controler registers and
add the missing definitions of the register block for the
SSMC.
The register contents definitions can be found in the pl093
header.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add definitions and an accessor macro to deal with
reading bus information from S3C2410_BWSCON for any
given numbered bank.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In the s3c_gpiolib_getchip implementation for s3c24xx the check whether a pin is
in the gpio banks range is reversed. Thus the function returns NULL for valid
pins and the gpio chip if its not valid.
As a result gpio states are not saved/restored properly during suspend/resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add platform device information for the ADC channels to be exported
via HWMON. This exports all the ADCs not being used for the touchscreen
interface.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Several GPIO functions have been returning -1 to indicate
an error instead of returning a proper error code. Change
to return -EINVAL for invalid argument(s).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Prepare to remove the large number of S3C2410_GPxn defines
by moving to S3C2410_GPx(n) in arch/arm.
The following perl was used to change the files:
perl -pi~ -e 's/S3C2410_GP([A-Z])([0-9]+)([^_^0-9])/S3C2410_GP\1\(\2\)\3/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the new style of GPIO numbering by using a single
macro for each GPIO bank. This means S3C2410_GPA0 becomes
S3C2410_GPA(0), and so on.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The <mach/regs-gpio.h> really does not need the input and output
pin configurations as these are standard and have a generic
representation (plus the s3c24xx gpio specific code is going to
be phased out soon).
The following sed was applied to remove the lines:
sed -i~ -e '/S3C2410_GP[A-Z][0-9]*_\INP/d' \
-e '/S3C2410_GP[A-Z][0-9]*_\OUTP/d' \
-e '/S3C2410_GPA[0-9]*_OUT/d'
to remove these.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the watchdog reset code from <mach/system-reset.h> to
a new file <plat/watchdog-reset.h> as this code is needed
by both s3c2410, s3c64xx and soon-to-be added s3c24a0.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The use of S3C2410_GP[A-Z]x_INP and S3C2410_GP[A-Z]x_OUTP are
very rare and are taking up large amounts of space in the
regs-gpio.h header.
The GPIO layer has had generic input and out defines called
S3C2410_GPIO_INPUT and S3C2410_GPIO_OUTPUT for a while which work
for all S3C24XX GPIOs.
Do the following replacements:
S3C2410_GP[A-Z][0-9]*_\OUTP => S3C2410_GPIO_OUTPUT
S3C2410_GP[A-Z][0-9]*_\INP => /S3C2410_GPIO_INPUT
S3C2410_GPA[0-9]*_OUT => S3C2410_GPIO_OUTPUT
to remove any usages of these and prepare the header for
the removal of these.
The following command was used to acheive this:
find . -type f -writable ! -name regs-gpio.h ! -name "*~" | xargs sed -i~ -e 's/S3C2410_GP[A-Z][0-9]*_\OUTP/S3C2410_GPIO_OUTPUT/g' -e 's/S3C2410_GP[A-Z][0-9]*_\INP/S3C2410_GPIO_INPUT/g' -e 's/S3C2410_GPA[0-9]*_OUT/S3C2410_GPIO_OUTPUT/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the s3c2410_gpio_irq2pin() function as it is not being
used in any in kernel driver and the function is probably not
being used anywhere else.
This is also part of the effort to remove any of the s3c24xx gpio
specific code that cannot be recreated by using the gpiolib
framework now in the kernel.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The BAST support code is calling s3c_i2c0_set_platdata() from
the map_io() entry, instead of the bast_init() code. This causes
the registration to fail due to kmalloc() not being available
at the time.
This fixes the following error:
s3c_i2c0_set_platdata: no memory for platform data
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The USB host base address is available on both the S3C24XX and S3C64XX
ranges.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add common definition for USB OHCI platform device, add a Kconfig
to selectively compile it and add update all the users.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change the name of S3C2410_DMA_CHANNELS to S3C_DMA_CHANNELS in the process.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The dma.h header does not need to include <mach/hardware.h> as there
is nothing it depends on. Remove the include and fixup the couple of
places where <mach/map.h> was not explicitly included (dragged in
via <mach/hardware.h>)
Note, we have to fix arch/arm/plat-s3c24xx/pm.c which seems to rely
on having <mach/hardware.h> included by this method.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the common information from the <mach/dma.h> header into a new
shareable <plat/dma.h> header for re-use on the s3c64xx.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The <mach/dma.h> is for the driver API for the DMA system and should
not have anything relying on the CPU specific registers.
Remove the registers to <plat/dma-regs.h> for the code that really
needs to know about them.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
calls
The S3C24XX DMA API channel configuration registers are being passed
values comprised of register values which makes it hard to move the
API to cover both the S3C24XX and S3C64XX.
These values can be calculated from knowing which device the channel
is connected to, so remove them from the two calls s3c2410_dma_config
and s3c2410_dma_devconfig.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the platform dma.h to dma-plat.h to ensure it doen't get
confused with plat/dma.h
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The platform data for the i2c-s3c2410 driver used to allow a min,
max and desired frequency for the I2C bus. This patch reduces it
to simply a desired frequency ceiling and corrects all the uses
of the platform data appropriately.
This means, for example, that on a system with a 66MHz fclk, a
request for 100KHz will achieve 65KHz which is safe and
acceptable, rather than 378KHz which it would have achieved
without this change.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
[ben-linux@fluff.org: tidy subject and description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (97 commits)
USB: qcserial: add device id for HP devices
USB: isp1760: Add a delay before reading the SKIPMAP registers in isp1760-hcd.c
USB: allow malformed LANGID descriptors
USB: pxa27x_udc: typo fixes and code cleanups
USB: gadget: gadget zero uses new suspend/resume hooks
USB: gadget: composite device-level suspend/resume hooks
USB: r8a66597-hcd: suspend/resume support
USB: more u32 conversion after transfer_buffer_length and actual_length
USB: Fix cp2101 USB serial device driver termios functions for console use
USB: CP2101 New Device ID
USB: ipaq: handle 4 endpoint devices
USB: S3C: Move usb-control.h to platform include
USB: ohci-hcd: Add ARCH_S3C24XX to the ohci-s3c2410.c glue
USB: pedantic: spelling correction in comment for ch9.h
USB: host: fix sparse warning: Using plain integer as NULL pointer
USB: ohci-s3c2410: fix name of bus clock
USB: ohci-s3c2410: remove <mach/hardware.h> include
USB: serial: rename cp2101 driver to cp210x
USB: CP2101 Reduce Error Logging
USB: CP2101 Support AN205 baud rates
...
The usb-control.h is needed by ohci-s3c2410.c for both S3C24XX and S3C64XX
architectures, so move it to <plat/usb-control.h>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not. There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().
This patch fixes things to pass this string to arch_reset(). This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These changes were included in the S3C audio header move but are not
directly related to it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the definition for S3C_GPIO_END to allow the PM code to build.
This means moving the GPIO bank numbers to a separate file to allow
the gpio and regs-gpio to include them. Including regs-gpio.h into
gpio.h causes too many build problems and adding gpio.h would mean
editing a large number of files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rename s3c2410_cpu_resume to s3c_cpu_resume and s3c2410_cpu_save to
s3c_cpu_save to remove the CPU specific naming of these functions
which are now in the generic PM code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since we have moved a large proportion of the PM code to the common
support area, remove the cpu specific name from the initialisation
function.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
