The DMA_CH_VALID bit used in the channel index should be masked out before
using it to access the channel array.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The function s3c_pwm_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Allow s3c24xx_set_fiq() to be exported so that it can be used by modules
wanting FIQ support.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The function s3c_adc_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-By: Ben Dooks <ben@simtec.co.uk>
Cc: Ramax Lo <ramaxlo@gmail.com>
Cc: Nelson Castillo <arhuaco@freaks-unidos.net>
Cc: linux-kernel@vger.kernel.org
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The naming of the defines suggests that there are three IISv4 ports
with one data line each when in fact there is a single IISv4 port
with three data lines.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This adds support for the third SDHCI controller.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The documentation for the S3C6410 CPU voltage scaling is rather
unclear, with omitted values for several speed settings. Originally
the code was using only quoted values, resulting in some fairly odd
settings. The S3C6410 is also unusual in that the both the maximum
and minimum voltages quoted scale as the frequency rises, rather
than just the minimum voltage.
Clean this up a bit by always using the specified typical settings
as the minimum voltage (ignoring any specified minimum voltage) in
order to avoid running near the edge of the processor capabilities.
Also use the next quoted maximum voltages rather than the typical
voltages where no maximum voltage is quoted, allowing operation on
a greater range of systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Currently the transition latency reported by the S3C64xx cpufreq
driver includes both the time for the CPU to reclock itself and
the time for a regulator to change voltage. This means that if
a regulator is not in use then the transition latency reported
is excessively high.
In future the regulator API will be extended to report latencies
so the driver will be able to query the performance of a given
regulator.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This provides symmetry with the voltage based checks done for the
regulator.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
DVDD is supplied by supplies derived from the PMIC, AVDD and PVDD are
supplied from the main wall supply on the base board which runs at
5V. No option is currently supported for running without a PMIC card,
the assumption is that the regulator API will be built out when no
soft PMIC card is in use.
To ease merge issues since this uses the newly added dev_name supply
configuration from the regulator API (currently in -next only) the
fixed voltage regulator is ifdefed out when the regulator API is not
enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Better using standard interfaces to enable/disable bluetooth
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add lcd and backlight device definition. The pwm backlight stuff does
not allow to really set maximum pwm as with my custom driver but it's
better to use standard driver instead of out of tree driver.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
[ben-linux@fluff.org: tidy header]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix mach-n30.c to use the s3c_i2c0_set_platdata() call to register the
platform data with the system to get rid of any reliance on having a real
device structure available in memory.
Since s3c_i2c0_set_platdata() copies the data, mark the original as
__initdata so it is thrown away.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The AT2440EVB should not be changing the s3c_device_sdi.name as this is
part of the initialisation process done by the CPU detection process
and actually present in arch/arm/plat-s3c24xx/s3c24xx.c.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The mach-h1940.c file was using s3c_device_ where it really should be
calling these local definitions h1940_device to ensure they are not
mistaken for real s3c_devices when the device change is done.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
There are a number of statements of the form A, B or A, B, C where
the numbers A,B,C are not consecutive. However, referencing [1] it
is the correct thing to replace these with A-B or A-C as apropriate.
[1] http://www.copyrightservice.co.uk/copyright/p03_copyright_notices
section 4iii 'Year of publication'
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
There are a number of statements of the form A, B or A, B, C where
the numbers A,B,C are consecutive. Tidy these up to be A-B or A-C
as appropriate and to comply better with copyright standards [1]
[1] http://www.copyrightservice.co.uk/copyright/p03_copyright_notices
section 4iii 'Year of publication'
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add documentation for the platform data structure in the SD/MMC driver
header file arch/arm/plat-s3c24xx/include/plat/mci.h.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a driver to provide DVS for the Simtec Osiris module to reduce
the power consumption whilst idling.
The DVS driver alters the voltage supplied to the ARM core depending
on the frequency it is running at. The driver itself does not do any
of the frequency alteration, which is left up to the cpufreq driver.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the platform/machine support for the audio devices fitted to
the Simtec range of boards since the move to ASoC.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add required machine definitions for SDHCI controller 0, 1 and 2. SMDKC100
has 2 SDHCI/MMC ports. Port 1 is directly connected to controller 0. Port
1 can be conntected to controler 1 or 2, depending on jumper setup.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Samsung S5PC100 has 3 SDHCI controllers compatible with the one known from
previous SoCs series. Add required platform setup and support code that
the devices can be used with sdhci-s3c driver.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add required machine definitions for I2C 0 and 1 bus controllers.
Currently no I2C device are defined yet.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Samsung S5PC100 has I2C bus controller compatible with the one known from
previous SoCs series. Add required platform setup and support code that
it can be used with s3c2410-i2c driver.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add required machine definitions for s3c-fb device.
A 800x480 lcd device (simmilar to the one known from SMDK6410 boards) has
been defined. The lcd controller is attached to GPIO lines and can be
enabled/disabled with platform-lcd driver.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Samsung S5PC100 has LCD-controller compatible with the one known from
previous SoCs series. Add required platform setup and support code that
it can be used with s3c-fb driver.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
S5PC1xx Samsung SOC series has very similar frame buffer hardware, so a lot
of the code can be shared. Moved s3c64xx-specific s3c-fb register
definitions from mach-s3c6400 to common platform directory as regs-fb-v4.h.
The new v4 file will be common for S3C6400, S3C6410, S5PC100 and possibly
others. Some s3c64xx series specific defines (palette handling) were left
in s3c-6400/mach/regs-fb.h, because it is handled differently in S5PC1xx
series.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add CPU idle support by a call to SoC build-in power management core.
Add system reset support by a simple write to system controll register.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for gpiolib calls. This is based on the gpiolib implementation
from plat-s3c64xx tree.
Add support for external interrupts for GPIO H banks.
Add support for GPIO interrupts for all banks.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
S5PC100 and S5PC110 GPIO registers differs in many places, rename all
previously defined registers to be S5PC100 specific.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add GPIO L0-L4 banks to register definition.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Clocks hierarchy has been completely reimplemented to match the S5PC100
specification.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
S5PC100 and S5PC110 clock registers differs in many places, rename all
previously defined registers to be S5PC100 specific. Remove all power
management registers. They will be added later to a separate file.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
S5PC110 and S5PC100 register maps differs in many places, rename all
defined registers to be S5PC100 specific. PA_SYS register known from
S3C64XX series has been renamed to more adequate PA_CLK. Also system map
has been also updated to cover more integrated peripherals.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We inted to re-organise the plat-s3c/plat-s3c24xx/plat-s3c64xx into a
more generic plat-samsung with less code in the other plat- directories
to make it easier to port new devices and try and clear up some of the
naming issues with newer devices.
Start by creating a small arch/arm/plat-samsung with no actuall code in
so we can move items in as we process them.
Add this to arch/arm to allow it to build things once support is added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Adjust OMAP3 frequency transition latency from 10,000,000uS to a more
reasonable 300,000uS. This causes ondemand and conservative governors to
sample CPU load more often resulting in more responsive behavior.
Tested on Android 2.6.29; using this value and conservative governor, CORE
power consumption on Zoom2 was comparable to the old and unresponsive
10,000,000uS value while UI responsiveness was greatly improved.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates defconfig to enable options needed to properly
boot OMAP3 pandora board. It also enables MMC, OTG, GPIO LEDs,
TWL4030 GPIO and sound drivers.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some drivers have dependencies on this, and therefore should be
enabled.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The host port power is enabled by driving the nEN_USB_PWR low as stated in
the comment. This fix is originally from Steve Sakoman <steve@sakoman.com>.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
