A very conservative check for bus activity (to prevent interference
in multimaster setups) prevented the bus recovery methods from being
triggered in the case that SDA or SCL was stuck low.
This defeats the purpose of the recovery mechanism, which was introduced
for exactly this situation (a slave device keeping SDA pulled down).
Also added a check to make sure SDA is low before attempting recovery.
If SDA is not stuck low, recovery will not help, so we can skip it.
Note that bus lockups can persist across reboots. The only other options
are to reset or power cycle the offending slave device, and many i2c
slaves do not even have a reset pin.
If we see that one of the lines is low for the entire timeout duration,
we can actually be sure that there is no other master driving the bus.
It is therefore save for us to attempt a bus recovery.
Signed-off-by: Claudio Foellmi <claudio.foellmi@ergon.ch>
Tested-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
[wsa: fixed one return code to -EBUSY]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move the check for a stuck SCL before the check for a high SDA.
This prevent false positives in the specific case that SDA is fine
and SCL is stuck, which previously returned 0.
Also check SDA again after the loop, if we can.
Together, these changes should lead to a lot more failed
recoveries being caught and returning error codes.
Signed-off-by: Claudio Foellmi <claudio.foellmi@ergon.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-img-scb driver already dynamically enables / disables clocks to
save power, but doesn't use the runtime PM framework. Convert the
driver to use runtime PM, so that dynamic clock management will be
disabled when runtime PM is disabled, and so that autosuspend can be
used to avoid unnecessarily disabling and re-enabling clocks repeatedly
during a sequence of transactions.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use of_property_read_bool to check for the existence of a property.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the restriction that the parent clock has to be a specific frequency
and also allow any speed to be supported.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add device-properties to make the bq24292i charger connected to
the bus get its input-current-limit from the fusb302 Type-C port
controller which is used on boards with the cht-wc PMIC,
as well as regulator_init_data for the 5V boost converter on
the bq24292i.
Since this means we now hook-up the bq24292i to the fusb302 Type-C port
controller add a check for the ACPI device which instantiates the fusb302.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For devices not instantiated through ACPI the i2c-client's device-name
gets set to <busnr>-<addr> by default, e.g. "0-0022" this means that
the device-name is dependent on the order in which the i2c-busses are
enumerated.
In some cases having a predictable constant device-name is desirable,
for example on non device-tree platforms the link between a regulator
and its consumers is specified by the platform code by setting
regulator_init_data.consumers. This array identifies the regulator's
consumers by dev_name and supply(-name). Which requires a constant
dev_name.
This commit adds a dev_name field to i2c_board_info allowing
platform code to set a contstant dev_name so that the device can
be identified by its dev_name in other platform code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org> (live at ELCE17)
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (live at ELCE17)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes this warning (found by build testing with 64bit):
format ‘%i’ expects argument of type ‘int’, but argument 3 has type
‘size_t {aka long unsigned int}’ [-Wformat=]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Use more compact of_property_read_bool() calls for the boolean properties
instead of of_find_property() calls in i2c_mux_reg_probe_dt().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Otherwise we can get the following if the fck alias is missing:
Unable to handle kernel paging request at virtual address fffffffe
...
PC is at clk_get_rate+0x8/0x10
LR is at omap_i2c_probe+0x278/0x6ec
...
[<c056eb08>] (clk_get_rate) from [<c06f4f08>] (omap_i2c_probe+0x278/0x6ec)
[<c06f4f08>] (omap_i2c_probe) from [<c0610944>] (platform_drv_probe+0x50/0xb0)
[<c0610944>] (platform_drv_probe) from [<c060e900>] (driver_probe_device+0x264/0x2ec)
[<c060e900>] (driver_probe_device) from [<c060cda0>] (bus_for_each_drv+0x70/0xb8)
[<c060cda0>] (bus_for_each_drv) from [<c060e5b0>] (__device_attach+0xcc/0x13c)
[<c060e5b0>] (__device_attach) from [<c060db10>] (bus_probe_device+0x88/0x90)
[<c060db10>] (bus_probe_device) from [<c060df68>] (deferred_probe_work_func+0x4c/0x14c)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the of_device_get_match_data() helper instead of open coding.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver needs to handle the flag I2C_M_RECV_LEN during receive to
support SMBus emulation.
Update receive logic to handle the case where the length is received
as the first byte of a transaction.
Also update the code to handle I2C_CLIENT_PEC, which is set when the
client sends a packet error checking code byte.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Kamlakant Patel <kamlakant.patel@cavium.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Get the input clock frequency to the controller from the linux clk
API, if it is available. This allows us to pass in the block input
frequency either from ACPI (using APD) or from device tree.
The old hardcoded frequency is used as default for backwards compatibility.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Kamlakant Patel <kamlakant.patel@cavium.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Don't populate const array supported_speeds on the stack, instead
make it static. Makes the object code smaller by 150 bytes:
Before:
text data bss dec hex filename
8474 1440 0 9914 26ba i2c-designware-platdrv.o
After:
text data bss dec hex filename
8324 1440 0 9764 2624 i2c-designware-platdrv.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
66AK2G has I2C instances that are not apart of the ALWAYS_ON power domain
unlike other Keystone 2 SoCs and OMAPL138. Therefore, pm_runtime
is required to insure the power domain used by the specific I2C instance is
properly turned on along with its functional clock.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBUS_BLOCK_DATA transactions might fail due to a race condition with
the IMC (Integrated Micro Controller), even when the IMC semaphore
is used.
This bug has been reported and confirmed by AMD, who suggested as a
solution an IMC firmware upgrade (obtained via BIOS update) and
disabling the IMC during SMBUS_BLOCK_DATA transactions.
Even without the IMC upgrade, the SMBUS is much more stable with this
patch.
Tested on a Bettong-alike board.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
AMD Family 17h uses the KERNCZ SMBus controller. While its documentation
is not publicly available, it is documented in the BIOS and Kernel
Developer’s Guide for AMD Family 15h Models 60h-6Fh Processors.
On this SMBus controller, the port select register is at PMx register
0x02, bit 4:3 (PMx00 register bit 20:19).
Without this patch, the 4 SMBus channels on AMD Family 17h chips are
mirrored and report the same chips on all channels.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The arguments for SDA and SCL were swapped. Fix it.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some SoC share one irq number between I2C controllers.
For example, on the LS2088 board, I2C 1 and I2C 2 share
one irq number. In this case, only one I2C controller
can register successfully, and others will fail.
Signed-off-by: Wei Jinhua <wei.jinhua1@zte.com.cn>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit b6c159a9cb ("i2c: ismt: Don't duplicate the receive length for
block reads") broke I2C block reads. It aimed to fix normal SMBus block
read, but changed the correct behavior of I2C block read in the process.
According to Documentation/i2c/smbus-protocol, one vital difference
between normal SMBus block read and I2C block read is that there is no
byte count prefixed in the data sent on the wire:
SMBus Block Read: i2c_smbus_read_block_data()
S Addr Wr [A] Comm [A]
S Addr Rd [A] [Count] A [Data] A [Data] A ... A [Data] NA P
I2C Block Read: i2c_smbus_read_i2c_block_data()
S Addr Wr [A] Comm [A]
S Addr Rd [A] [Data] A [Data] A ... A [Data] NA P
Therefore the two transaction types need to be processed differently in
the driver by copying of the dma_buffer as done previously for the
I2C_SMBUS_I2C_BLOCK_DATA case.
Fixes: b6c159a9cb ("i2c: ismt: Don't duplicate the receive length for block reads")
Signed-off-by: Pontus Andersson <epontan@gmail.com>
Tested-by: Stephen Douthit <stephend@adiengineering.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c fixes from Wolfram Sang:
"I2C has three driver fixes for the newly introduced drivers and one ID
addition for the i801 driver"
* 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: make structure stm32f7_setup static const
i2c: ensure termination of *_device_id tables
i2c: i801: Add support for Intel Cedar Fork
i2c: stm32f7: fix setup structure
The structure stm32f7_setup is local to the source and does not need
to be in global scope, make it static const.
Cleans up sparse warning:
symbol 'stm32f7_setup' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure (of/i2c/platform)_device_id tables are NULL terminated.
Found by coccinelle spatch "misc/of_table.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add PCI ID for Intel Cedar Fork PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C drive setup structure is not properly allocated.
Make it static instead of pointer to store driver data.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As reported by Rajat Jain, there are problems when ACPI operation
region handlers or similar, called at the ->resume_early() time, for
I2C client devices try to access an I2C controller that has already
been suspended at that point. To avoid that, move the suspend/resume
of i2c-designware-platdrv to the late/early stages, respectively.
While at it, avoid resuming the device from runtime suspend in the
driver's ->suspend callback which isn't particularly nice. [A better
approach would be to make the driver track the PM state of the device
so that it doesn't need to resume it in ->suspend, so implement it.]
First, drop dw_i2c_plat_suspend() added by commit a23318feef (i2c:
designware: Fix system suspend) and rename dw_i2c_plat_runtime_suspend()
back to dw_i2c_plat_suspend().
Second, point the driver's ->late_suspend and ->early_resume
callbacks, rather than its ->suspend and ->resume callbacks,
to dw_i2c_plat_suspend() and dw_i2c_plat_resume(), respectively,
so that they are not executed in parallel with each other, for
example if runtime resume of the device takes place during system
suspend.
Finally, add "suspended" and "skip_resume" flags to struct dw_i2c_dev
and make dw_i2c_plat_suspend() and dw_i2c_plat_resume() use them to
avoid suspending or resuming the device twice in a row and to avoid
resuming a previously runtime-suspended device during system resume.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Johannes Stezenbach <js@sig21.net>
Tested-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The power management handling in dw_i2c_plat_probe() is somewhat
messy and it is rather hard to figure out the code intention for
the case when pm_disabled is set. In that case, the driver doesn't
enable runtime PM at all, but in addition to that it calls
pm_runtime_forbid() as though it wasn't sure if runtime PM might
be enabled for the device later by someone else.
Although that concern doesn't seem to be actually valid, the
device is clearly still expected to be PM-capable even in the
pm_disabled set case, so a better approach would be to enable
runtime PM for it unconditionally and prevent it from being
runtime-suspended by using pm_runtime_get_noresume().
Make the driver do that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update my imgtec.com and personal email address to my kernel.org one in
a few places as MIPS will soon no longer be part of Imagination
Technologies, and add mappings in .mailcap so get_maintainer.pl reports
the right address.
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds initial support for the STM32F7 I2C controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch uses a more generic definition of speed enum for i2c-stm32f4
driver.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add driver support for the Altera I2C Controller. The I2C
controller is soft IP for use in FPGAs.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- new drivers for Spreadtrum I2C, Intel Cherry Trail Whiskey Cove SMBUS
- quite some driver updates
- cleanups for the i2c-mux subsystem
- some subsystem-wide constification
- further cleanup of include/linux/i2c
* 'i2c/for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (50 commits)
i2c: sprd: Fix undefined reference errors
i2c: nomadik: constify amba_id
i2c: versatile: Make i2c_algo_bit_data const
i2c: busses: make i2c_adapter_quirks const
i2c: busses: make i2c_adapter const
i2c: busses: make i2c_algorithm const
i2c: Add Spreadtrum I2C controller driver
dt-bindings: i2c: Add Spreadtrum I2C controller documentation
i2c-cht-wc: make cht_wc_i2c_adap_driver static
MAINTAINERS: Add entry for drivers/i2c/busses/i2c-cht-wc.c
i2c: aspeed: Retain delay/setup/hold values when configuring bus frequency
dt-bindings: i2c: eeprom: Document vendor to be used and deprecated ones
i2c: i801: Restore the presence state of P2SB PCI device after reading BAR
MAINTAINERS: drop entry for Blackfin I2C and Sonic's email
blackfin: merge the two TWI header files
i2c: davinci: Preserve return value of devm_clk_get
i2c: mediatek: Add i2c compatible for MediaTek MT7622
dt-bindings: i2c: Add MediaTek MT7622 i2c binding
dt-bindings: i2c: modify information formats
i2c: mux: i2c-arb-gpio-challenge: allow compiling w/o OF support
...
Since the i2c driver of Spreadtrum can not be build as one module, thus
it should depend on CONFIG_I2C is build in.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Lenovo Miix2 8 DSDT contains an i2c clk / bus speed of 1700000 Hz
for one if its devices, which is not supported.
This is the second DSDT to show up with an unsupported clk in a short
time, remove the hardcoded fix for DSDTs with a 1 MiHz clock and simply
always round down the clk to the nearest supported value.
Reported-by: russianneuromancer@ya.ru
Fixes: 682c6c2188 ("i2c: designware: Some broken DSTDs use 1MiHz ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make this const as it is only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make these const as they are only stored as a reference in the quirks
field of an i2c_adapter structure, which is const. Done using
Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make these const as they are only stored in the algo field of
i2c_adapter structure, which is const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Compare the number of bytes actually seen on the wire to the byte
count field returned by the slave device.
Previously we just overwrote the byte count returned by the slave
with the real byte count and let the caller figure out if the
message was sane.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com>
Tested-by: Dan Priamo <danp@adiengineering.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
According to Table 15-14 of the C2000 EDS (Intel doc #510524) the
rx data pointed to by the descriptor dptr contains the byte count.
desc->rxbytes reports all bytes read on the wire, including the
"byte count" byte. So if a device sends 4 bytes in response to a
block read, on the wire and in the DMA buffer we see:
count data1 data2 data3 data4
0x04 0xde 0xad 0xbe 0xef
That's what we want to return in data->block to the next level.
Instead we were actually prefixing that with desc->rxbytes:
bad
count count data1 data2 data3 data4
0x05 0x04 0xde 0xad 0xbe 0xef
This was discovered while developing a BMC solution relying on the
ipmi_ssif.c driver which was trying to interpret the bogus length
field as part of the IPMI response.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com>
Tested-by: Dan Priamo <danp@adiengineering.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch adds the I2C controller driver for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The structure cht_wc_i2c_adap_driver is local to the source
and does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'cht_wc_i2c_adap_driver' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In addition to the base, low and high clock configuration, the AC timing
register #1 on the AST2400 houses fields controlling:
1. tBUF: Minimum delay between Stop and Start conditions
2. tHDSTA: Hold time for the Start condition
3. tACST: Setup time for Start and Stop conditions, and hold time for the
Repeated Start condition
These values are defined in hardware on the AST2500 and therefore don't
need to be set.
aspeed_i2c_init_clk() was performing a direct write of the generated
clock values rather than a read/mask/modify/update sequence to retain
tBUF, tHDSTA and tACST, and therefore cleared the tBUF, tHDSTA and tACST
fields on the AST2400. This resulted in a delay/setup/hold time of 1
base clock, which in some configurations is not enough for some devices
(e.g. the MAX31785 fan controller, with an APB of 48MHz and a desired
bus speed of 100kHz).
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sun, Yunying reported the following failure on Denverton micro-server:
EDAC DEBUG: pnd2_init:
EDAC DEBUG: pnd2_probe:
EDAC DEBUG: dnv_rd_reg: Read b_cr_tolud_pci=00000000_80000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_lo_pci=00000000_80000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_hi_pci=00000000_00000004
EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region0_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region1_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_base_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_mask_mchbar=00000000_00000000
EDAC pnd2: Failed to register device with error -19.
On Denverton micro-server, the presence of the P2SB bridge PCI device is
enabled or disabled by the item 'RelaxSecConf' in BIOS setup menu. When
'RelaxSecConf' is enabled, the P2SB PCI device is present and the pnd2_edac
EDAC driver also uses it to get BAR. Hiding the P2SB PCI device caused the
pnd2_edac EDAC driver failed to get BAR then reported the above failure.
Therefor, store the presence state of P2SB PCI device before unhiding it
for reading BAR and restore the presence state after reading BAR.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Reported-by: Yunying Sun <yunying.sun@intel.com>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There seems to be no need for separate ones since all users include both
files anyhow. Merge them because include/linux/i2c is to be deprecated.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c driver can run into driver dependency issues if its loaded
before a clock driver it depends on. Therefore, EPROBE_DEFER may be
returned by devm_clk_get and should be returned in probe to allow the
kernel to reprobe the driver at a later time. This patch allows the error
value returned by devm_clk_get to be passed through and not overwritten.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
