Now we deal with mesh forwarding before the 802.11->802.3 conversion, thus
eliminating a few unnecessary steps. The next hop lookup is called from
ieee80211_master_start_xmit() instead of subif_start_xmit(). Until the next hop
is found, RA in the frame will be all zeroes for frames originating from the
device. For forwarded frames, RA will contain the TA of the received frame,
which will be necessary to send a path error if a next hop is not found.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to 802.11-2007, we are doing the wrong thing in the
sequence number checks when receiving frames. This fixes it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the check at the entrance to ieee80211_rx_reorder_ampdu.
This check has been broken by 'mac80211: rx.c use new helpers'.
Letting QoS NULL packet in ieee80211_rx_reorder_ampdu led to packet loss in
RX.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, almost every interface type has a 'bss' pointer
pointing to BSS information. This BSS information, however,
is for a _local_ BSS, not for the BSS we joined, so having
it on a STA mode interface makes little sense, but now they
have it pointing to the master device, which is an AP mode
virtual interface. However, except for some bitrate control
data, this pointer is only used in AP/VLAN modes (for power
saving stations.)
Overall, it is not necessary to even have the master netdev
be a valid virtual interface, and it doesn't have to be on
the list of interfaces either.
This patch changes the master netdev to be special, it now
- no longer is on the list of virtual interfaces, which
lets me remove a lot of tests for that
- no longer has sub_if_data attached, since that isn't used
Additionally, this patch changes some vlan/ap mode handling
that is related to these 'bss' pointers described above (but
in the VLAN case they actually make sense because there they
point to the AP they belong to); it also adds some debugging
code to IEEE80211_DEV_TO_SUB_IF to validate it is not called
on the master netdev any more.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also remove the WLAN_IS_QOS_DATA inline after removing the last
two users. This starts moving away from using rx->fc to using
the header frame_control directly.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reworks the mac80211 debug settings making them more focused
and adding help text for those that didn't have one. It also removes a
number of printks that can be triggered remotely and add no value, e.g.
"too short deauthentication frame received - ignoring".
If somebody really needs to debug that they should just add a monitor
interface and look at the frames in wireshark.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the RX path to no longer use function pointers for
RX handlers but rather invoke them directly. If debugging is
enabled, mark the RX handlers noinline because otherwise they
all get inlined into ieee80211_invoke_rx_handlers() which makes
it harder to see where a bug is.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In IBSS mode prior to join/creation of new IBSS it is possible that
a frame from unknown station is received and an ibss_add_sta() is
called. This will cause a warning in rate_lowest_index() since the
list of supported rates of our station is not initialized yet.
The fix is to add ibss stations with a rate we received that frame
at; this single-element set will be extended later based on beacon
data. Also there is no need to store stations from a foreign IBSS.
Signed-off-by: Vladimir Koutny <vlado@ksp.sk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This addresses an alignment issue with compare_ether_addr().
The addresses passed to compare_ether_addr should be two bytes aligned.
It may function properly in x86 platform. However may not work properly
on IA-64 or ARM processor.
This also fixes a typo in mlme.c where the sk_buff struct name is incorect.
Though sizeof() works for any incorrect structure pointer name as its just
a pointer length that we want, lets just fix it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The useless channel use statistics are quite a lot of code, currently
use integer divisions in the packet fast path, are rather inaccurate
since they do not account for retries and finally nobody even cares.
Hence, remove them completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use hw flags and rx flags to determine which fields are present in the header
and use all available information from the driver.
make sure radiotap header starts at a naturally aligned address (mod 8) for
all radiotap fields.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
trying to clean up the signal/noise code. the previous code in mac80211 had
confusing names for the related variables, did not have much definition of
what units of signal and noise were provided and used implicit mechanisms from
the wireless extensions.
this patch introduces hardware capability flags to let the hardware specify
clearly if it can provide signal and noise level values and which units it can
provide. this also anticipates possible new units like RCPI in the future.
for signal:
IEEE80211_HW_SIGNAL_UNSPEC - unspecified, unknown, hw specific
IEEE80211_HW_SIGNAL_DB - dB difference to unspecified reference point
IEEE80211_HW_SIGNAL_DBM - dBm, difference to 1mW
for noise we currently only have dBm:
IEEE80211_HW_NOISE_DBM - dBm, difference to 1mW
if IEEE80211_HW_SIGNAL_UNSPEC or IEEE80211_HW_SIGNAL_DB is used the driver has
to provide the maximum value (max_signal) it reports in order for applications
to make sense of the signal values.
i tried my best to find out for each driver what it can provide and update it
but i'm not sure (?) for some of them and used the more conservative guess in
doubt. this can be fixed easily after this patch has been merged by changing
the hardware flags of the driver.
DRIVER SIGNAL MAX NOISE QUAL
-----------------------------------------------------------------
adm8211 unspec(?) 100 n/a missing
at76_usb unspec(?) (?) unused missing
ath5k dBm dBm percent rssi
b43legacy dBm dBm percent jssi(?)
b43 dBm dBm percent jssi(?)
iwl-3945 dBm dBm percent snr+more
iwl-4965 dBm dBm percent snr+more
p54 unspec 127 n/a missing
rt2x00 dBm n/a percent rssi+tx/rx frame success
rt2400 dBm n/a
rt2500pci dBm n/a
rt2500usb dBm n/a
rt61pci dBm n/a
rt73usb dBm n/a
rtl8180 unspec(?) 65 n/a (?)
rtl8187 unspec(?) 65 (?) noise(?)
zd1211 dB(?) 100 n/a percent
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As discussed earlier, we can unify locking in struct sta_info
and use just a single spinlock protecting all members of the
structure that need protection. Many don't, but one of the
especially bad ones is the 'flags' member that can currently
be clobbered when RX and TX is being processed on different
CPUs at the same time.
Because having four spinlocks for different, mostly exclusive
parts of a single structure is overkill, this patch also kills
the ampdu and mesh plink spinlocks and uses just a single one
for everything. Because none of the spinlocks are nested, this
is safe.
It remains to be seen whether or not we should make the sta
flags use atomic bit operations instead, for now though this
is a safe thing and using atomic operations instead will be
very simple using the new static inline functions this patch
introduces for accessing sta->flags.
Since spin_lock_bh() is used with this lock, there shouldn't
be any contention even if aggregation is enabled at around the
same time as both requires frame transmission/reception which
is in a bh context.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Tomas Winkler <tomasw@gmail.com>
Cc: Ron Rindjunsky <ron.rindjunsky@intel.com>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this patch, if xmit_skb is null but net_ratelimit() returns 0 we would
go to the else branch and access the null xmit_skb. Pointed out by Johannes
Berg.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This
* makes the queue number passed to drivers a u16
(as it will be with skb_get_queue_mapping)
* removes the useless queue number defines
* splits hw->queues into hw->queues/ampdu_queues
* removes the debugfs files for per-queue counters
* removes some dead QoS code
* removes the beacon queue configuration for IBSS
so that the drivers now never get a queue number
bigger than (hw->queues + hw->ampdu_queues - 1)
for tx and only in the range 0..hw->queues-1 for
conf_tx.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an off-by-one in net/mac80211/rx.c introduced by
commit 8318d78a44
(cfg80211 API for channels/bitrates, mac80211 and driver conversion)
and spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some people are getting this message a lot, and we have traced it to
broken access points that much too often send completely empty frames
(all bytes zeroed, which they shouldn't do at all.)
Since we cannot do anything about such frames in any case except the
special case where we're debugging an AP, just remove the message.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames all mac80211 files (except ieee80211_i.h) to get rid
of the useless ieee80211_ prefix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch alters the A-MPDU MLME in sta_info to use dynamic allocation,
thus drastically improving memory usage - from a constant ~2 Kbyte in
the previous (static) allocation to a lower limit of ~200 Byte and an upper
limit of ~2 Kbyte.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes access to the STA hash table/list use RCU to protect
against freeing of items. However, it's not a true RCU, the
copy step is missing: whenever somebody changes a STA item it
is simply updated. This is an existing race condition that is
now somewhat understandable.
This patch also fixes the race key freeing vs. STA destruction
by making sure that sta_info_destroy() is always called under
RTNL and frees the key.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split it into ieee80211_tx_data and ieee80211_rx_data to clarify
usage/flag usage and remove the stupid union thing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moves another ifdef into the sta_info header file in favour of
compiling more code even w/o CONFIG_MAC80211_MESH.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various cleanups, reducing the #ifdef mess and other things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the TX/RX paths in mac80211 to support mesh interfaces.
This code will be cleaned up later again before being enabled.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This consolidates all TIM handling code to avoid re-introducing
errors with the bitmap/set_tim order and to reduce code. While
reading the code I noticed a possible problem so I also added
a comment about that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM flag that is kept in each station's info is completely
useless, there's no code (aside from the debugfs display code)
checking it, hence it can be removed. While doing that, I noticed
that the TIM handling is broken when buffered frames expire, so
fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers should be allowed to simply get a complete new beacon when
set_tim() is invoked (and set_tim() is required for drivers that
just want a beacon template!), so we need to update our own TIM
bitmap before calling set_tim() so that getting the beacon will
now get an already updated beacon.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This doesn't really need to be a full int variable since it's
just a flag to indicate a PS-poll is in progress.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enable IBSS cell merging. if an IBSS beacon with the same channel, same ESSID
and a TSF higher than the local TSF (mactime) is received, we have to join its
BSSID. while this might not be immediately apparent from reading the 802.11
standard it is compliant and necessary to make IBSS mode functional in many
cases. most drivers have a similar behaviour.
* move the relevant code section (previously only containing debug code) down
to the end of the function, so we can reuse the bss structure.
* we have to compare the mactime (TSF at the time of packet receive) rather
than the current TSF. since mactime is defined as the time the first data
symbol arrived we add the time until byte 24 where the timestamp resides, since
this is how the beacon timestamp is defined. as some some drivers are not able
to give a reliable mactime we fall back to use the current TSF, which will be
enough to catch most (but not all) cases where an IBSS merge is necessary.
* in IBSS mode we want to allow beacons to override probe response info so we
can correctly do merges.
* we don't only configure beacons based on scan results, so change that
message.
* to enable this we have to let all beacons thru in IBSS mode, even if they
have a different BSSID.
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions time_before, time_before_eq, time_after, and time_after_eq are more robust for comparing jiffies against other values.
So following patch implements usage of the time_after() macro, defined at linux/jiffies.h, which deals with wrapping correctly
Cc: linux-wireless@vger.kernel.org
Signed-off-by: S.Çağlar Onur <caglar@pardus.org.tr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds "cooked" monitor mode to mac80211. A monitor interface
in "cooked" mode will see all frames that mac80211 has not used
internally.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is some duplicated code that sits in front of each function
call to ieee80211_invoke_rx_handlers() that can very well be part
of that function if it gets slightly different arguments.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't really make sense to have extra pointers to the RX/TX
handler arrays instead of just using the arrays directly, that
also allows us to make them static.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Uninline ieee80211_invoke_rx_handlers to save .text space,
make the code more readable in some places and remove the
"optimisation" that is hit only very few times and unclear
to start with.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some instances of RX_DROP mean that the frame was useless,
others mean that the frame should be visible in userspace
on "cooked" monitor interfaces. This patch splits up RX_DROP
and changes each instance appropriately.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The _DROP result will need to be split in the RX path but not
in the TX path, so for preparation split up the type into two
types, one for RX and one for TX. Also make sure (via sparse)
that they cannot be confused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the 802.1X port acess control enable flag
since it is not required. Instead, set the authorized flag for
each station that we normally communicate with (WDS peers, IBSS
peers and APs we're associated to) and require hostapd to set
the authorized flag for all stations when port control is not
enabled.
Also, since I was working in that area, this documents station
flags and removes the unused "permanent" one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These handlers do not really return a status and the compiler
can do a much better job when they're simply static functions
that it can inline if appropriate. Also makes the code shorter.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver authors should be aware of the alignment requirements, but
not everybody cares about the warning. This patch makes it depend
on a new Kconfig symbol MAC80211_DEBUG_PACKET_ALIGNMENT which can
be enabled regardless of MAC80211_DEBUG and is recommended for
driver authors (only). This also restricts the warning to data
packets so other packets need not be realigned to not trigger the
warning.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a wrong condition for null qos data frames, causing us to
drop data frames needed for reordering as well.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I introduced the alignment warning I forgot the A-MSDU case which
has a different requirement because each frame contains 14-byte 802.3
headers in front of the IP payload. This patch moves the alignment
warning to a place where we know whether we're dealing with an A-MSDU
frame and adjusts it accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds static declarations to functions in the Rx flow in order to
eliminate sparse errors
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit c7a51bda ("mac80211: restructure __ieee80211_rx") extracted
__ieee80211_rx_handle_packet out of __ieee80211_rx and hence changed
the locking rules for __ieee80211_rx_handle_packet(), it is now
invoked under RCU lock. There is, however, one instance left where
it contains an rcu_read_unlock() in an error path, which is a bug.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that support mixed AP/STA operation may well need to
know the type of a virtual interface when iterating over them.
The easiest way to support that is to move the interface type
variable into the vif structure.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the ability to handle Block Ack Request
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch handles the reordering of the Rx A-MPDU.
This issue occurs when the sequence of the internal MPDUs is not in the
right order. such a case can be encountered for example when some MPDUs from
previous aggregations were recieved, while others failed, so current A-MPDU
will contain a mix of re-transmited MPDUs and new ones.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes a separation between Rx frame pre-handling which stays in
__ieee80211_rx and Rx frame handlers, moving to __ieee80211_rx_handle_packet.
Although this separation has no affect in regular mode of operation, this kind
of mechanism will be used in A-MPDU frames reordering as it allows accumulation
of frames during pre-handling, dispatching them to later handling when necessary.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem with rx handling on multiple interfaces. Especially
when using hardware-scanning and a wireless driver (i.e. iwlwifi) which is
able to receive data while scanning.
The rx handlers can modify the skb and the frame control field (see
ieee80211_rx_h_remove_qos_control) but since every interface gets its own
copy of the skb each should get its own copy of rx.fc too.
In my case the wlan0-interface did not remove the qos-control from the frame
because the corresponding flag in rx.fc was already removed while processing
the frame on the master interface. Therefore somehow corrupted frames were
passed to the userspace.
Signed-off-by: Helmut Schaa <hschaa@suse.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleans up the eapol frame handling and some related code in the
receive and transmit paths. After this patch
* EAPOL frames addressed to us or the EAPOL group address are
always accepted regardless of whether they are encrypted or not
* other frames from a station are dropped if PAE is enabled and
the station is not authorized
* unencrypted frames (except the EAPOL frames above) are dropped if
drop_unencrypted is enabled
* some superfluous code that eth_type_trans handles anyway is gone
* port control is done for transmitted packets
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes should_drop_frame function to pass in ps poll control
frames required for power save functioanlity. Interface types that do not
have interest for PS POLL frames now drop it in handler.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes mac80211 include the low-level MAC timestamp
in the radiotap header if the driver indicated (by a new
RX flag) that the timestamp is valid.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves u8 amsdu_frame in ieee80211_txrx_data to the flags
section as IEEE80211_TXRXD_RX_AMSDU
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ability to receive and handle A-MSDU frames.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch restructures the Rx handlers chain by incorporating previously
handlers ieee80211_rx_h_802_1x_pae and ieee80211_rx_h_drop_unencrypted
into ieee80211_rx_h_data, already in 802.3 form. this scheme follows more
precisely after the IEEE802.11 data plane archituecture, and will prevent
code duplication to IEEE8021.11n A-MSDU handler.
added function:
- ieee80211_data_to_8023: transfering 802.11 data frames to 802.3 frame
- ieee80211_deliver_skb: delivering the 802.3 frames to upper stack
eliminated handlers:
- ieee80211_rx_h_drop_unencrypted: now function ieee80211_drop_unencrypted
- ieee80211_rx_h_802_1x_pae: now function ieee80211_802_1x_pae
changed handlers:
- ieee80211_rx_h_data: now contains calls to four above function
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scan code in mac80211 makes the software scan assumption in various
places. For example, we stop the Tx queue during a software scan so that
all the Tx packets will be queued by the stack. We also drop frames not
related to scan in the software scan process. But these are not true for
hardware scan.
Some wireless hardwares (for example iwl3945/4965) has the ability to
perform the whole scan process by hardware and/or firmware. The hardware
scan is relative powerful in that it tries to maintain normal network
traffic while doing a scan in the background. Some drivers (i.e iwlwifi)
do provide a way to tune the hardware scan parameters (for example if the
STA is associated, what's the max time could the STA leave from the
associated channel, how long the scans get suspended after returning to
the service channel, etc). But basically this is transparent to the
stack. mac80211 should not stop Tx queues or drop Rx packets during a
hardware scan.
This patch resolves the above problem by spliting the current scan
indicator local->sta_scanning into local->sta_sw_scanning and
local->sta_hw_scanning. It then changes the scan related code to be aware
of hardware scan or software scan in various places. With this patch,
iwlwifi performs much better in the scan-while-associated condition and
disable_hw_scan=1 should never be required.
Cc: Mohamed Abbas <mohamed.abbas@intel.com>
Cc: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 81100eb80a for the
release, to avoid the unnecessary warning noise that is only really
relevant to wireless driver developers.
The warning will probably go right back in after I cut the release, but
at least we won't unnecessarily worry users.
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes mac80211 warn (once) when the driver passes up a
frame in which the payload data is not aligned on a four-byte
boundary, with a long comment for people who run into the condition
and need to know what to do.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression I (most likely) introduced, namely that
unencrypted frames are right now accepted even if we have a key for that
specific sender. That has very bad security implications.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make "decrypt failed" and "have no key" debugging messages compile
conditionally upon CONFIG_MAC80211_DEBUG. They have been useful for
finding certain problems in the past, but in many cases they just
clutter a user's logs.
A typical example is an enviornment where multiple SSIDs are using a
single BSSID but with different protection schemes or different keys
for each SSID. In such an environment these messages are just noise.
Let's just leave them for those interested enough to turn-on debugging.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The decryption handlers will skip the frame if the RX_FLAG_DECRYPTED
flag is set, so the early flag setting introduced by Johannes breaks
decryption. To work around this, call the handlers first and then set
the flag.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This "algorithm" is used only internally and is not useful.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes mac80211 set the RX_FLAG_DECRYPTED flag for frames
decrypted in software allowing us to handle some things more
uniformly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we have three RX handlers doing the decryption.
This patch changes it to have only one handler doing
everything, thereby getting rid of many duplicate checks.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
--
net/mac80211/rx.c | 46 ++++++++++++----------------------------------
1 files changed, 12 insertions(+), 34 deletions(-)
This moves the sta_process RX handler to after decryption
so that frames that cannot be decrypted don't influence
statistics, it is likely that they were injected or something
else is totally wrong.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes the management interface since it is only required
for hostapd/userspace MLME, will not be in the final tree
at least in this form and hostapd/userspace MLME currently
do not work against this tree anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since I cannot convince the lazy driver authors (hello Michael)
to stop (ab)using the MGMT interface type internally in their
drivers, this patch introduces a new _INVALID type especially
for their use and changes all affected drivers to use it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we update the counters iff_promiscs and iff_allmultis
in struct ieee80211_local we have no common lock held to
protect them. The problem is that the update to each counter
may not be atomic, so we could end up with iff_promiscs == -1
in unfortunate conditions. To fix it, use atomic_t values.
It doesn't matter whether the two counters are updated
together atomically or not, if there are two invocations
of set_multicast_list we will end up with multiple
configure_filter() invocations of which the latter will always
be correct.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
VLAN interfaces have yet another bug: they aren't accounted
for properly in the receive path in prepare_for_handlers().
I noticed this by code inspection, but it would be easy for
the compiler to catch such things if we'd just use the proper
enum where appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, we run through all three crypto algorithms for each
received frame even though we have previously determined which
key we have and as such already know which algorithm will be
used. Change it to invoke only the needed function. Also move
the WEP decrypt handler to wep.c so that fewer functions need
to be non-static.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 pass all frames to monitor interfaces early
before all receive processing with the benefit that only a single
copy needs to be made, all monitors can receive clones of the skb
and if the frame will be discarded we don't even need to make a
single copy.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Florian Lohoff noticed a bug in mac80211: when bringing the
master interface down while other virtual interfaces are up
we call dev_close() under a spinlock which is not allowed.
This patch removes the sub_if_lock used by mac80211 in favour
of using an RCU list. All list manipulations are already done
under rtnl so are well protected against each other, and the
read-side locks we took in the RX and TX code are already in
RCU read-side critical sections.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Florian Lohoff <flo@rfc822.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.
This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.
Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.
At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().
The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.
Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 print out the wiphy name instead of the
master device name where appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the key threshold stuff from mac80211.
I have patches for later that add it as a per-key setting
to nl/cfg80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows drivers to indicate bad FCS/PLCP CRC to the stack and
have the stack drop packets like that except for monitor interfaces.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few TODO comments in the mac80211 sources regarding
hardware offload for Michael MIC verification. Those items are,
however, better handled in the driver instead of the stack, if
any device requires such hand-holding.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stats are now available for device usage inside network_device
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the various hardware crypto related
flags to make them more local, i.e. put them with each
key or each packet instead of into the hw struct.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all mention of the atheros turbo modes that
can't possibly work properly anyway since in some places we don't
check for them when we should.
I have no idea what the iwlwifi drivers were doing with these but
it can't possibly have been correct.
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During receive processing, we select the key long before using it and
because there's no locking it is possible that we kfree() the key
after having selected it but before using it for crypto operations.
Obviously, this is bad.
Secondly, during transmit processing, there are two possible races: We
have a similar race between select_key() and using it for encryption,
but we also have a race here between select_key() and hardware
encryption (both when a key is removed.)
This patch solves these issues by using RCU: when a key is to be freed,
we first remove the pointer from the appropriate places (sdata->keys,
sdata->default_key, sta->key) using rcu_assign_pointer() and then
synchronize_rcu(). Then, we can safely kfree() the key and remove it
from the hardware. There's a window here where the hardware may still
be using it for decryption, but we can't work around that without having
two hardware callbacks, one to disable the key for RX and one to disable
it for TX; but the worst thing that will happen is that we receive a
packet decrypted that we don't find a key for any more and then drop it.
When we add a key, we first need to upload it to the hardware and then,
using rcu_assign_pointer() again, link it into our structures.
In the code using keys (TX/RX paths) we use rcu_dereference() to get the
key and enclose the whole tx/rx section in a rcu_read_lock() ...
rcu_read_unlock() block. Because we've uploaded the key to hardware
before linking it into internal structures, we can guarantee that it is
valid once get to into tx().
One possible race condition remains, however: when we have hardware
acceleration enabled and the driver shuts down the queues, we end up
queueing the frame. If now somebody removes the key, the key will be
removed from hwaccel and then then driver will be asked to encrypt the
frame with a key index that has been removed. Hence, drivers will need
to be aware that the hw_key_index they are passed might not be under
all circumstances. Most drivers will, however, simply ignore that
condition and encrypt the frame with the selected key anyway, this
only results in a frame being encrypted with a wrong key or dropped
(rightfully) because the key was not valid. There isn't much we can
do about it unless we want to walk the pending frame queue every time
a key is removed and remove all frames that used it.
This race condition, however, will most likely be solved once we add
multiqueue support to mac80211 because then frames will be queued
further up the stack instead of after being processed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sta_info.assoc_ap value is used as a flag, move it
into flags.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I changed the code there I forgot to mention what happens
with multicast frames in a regular BSS and keep wondering myself
if the code is correct. Add appropriate comments.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In STA mode, the AP will echo our traffic. This includes multicast
traffic.
Receiving these frames confuses some protocols and applications,
notably IPv6 Duplicate Address Detection.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current version of wireless statistics contains a bug in the averaging
that makes the numbers be too sticky and not react to small changes. This
patch removes all averaging.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves all the key handling code out from ieee80211_ioctl.c
into key.c and also does the following changes including documentation
updates in mac80211.h:
1) Turn off hardware acceleration for keys when the interface
is down. This is necessary because otherwise monitor
interfaces could be decrypting frames for other interfaces
that are down at the moment. Also, it should go some way
towards better suspend/resume support, in any case the
routines used here could be used for that as well.
Additionally, this makes the driver interface nicer, keys
for a specific local MAC address are only ever present
while an interface with that MAC address is enabled.
2) Change driver set_key() callback interface to allow only
return values of -ENOSPC, -EOPNOTSUPP and 0, warn on all
other return values. This allows debugging the stack when
a driver notices it's handed a key while it is down.
3) Invert the flag meaning to KEY_FLAG_UPLOADED_TO_HARDWARE.
4) Remove REMOVE_ALL_KEYS command as it isn't used nor do we
want to use it, we'll use DISABLE_KEY for each key. It is
hard to use REMOVE_ALL_KEYS because we can handle multiple
virtual interfaces with different key configuration, so we'd
have to keep track of a lot of state for this and that isn't
worth it.
5) Warn when disabling a key fails, it musn't.
6) Remove IEEE80211_HW_NO_TKIP_WMM_HWACCEL in favour of per-key
IEEE80211_KEY_FLAG_WMM_STA to let driver sort it out itself.
7) Tell driver that a (non-WEP) key is used only for transmission
by using an all-zeroes station MAC address when configuring.
8) Change the set_key() callback to have access to the local MAC
address the key is being added for.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch embeds the struct ieee80211_key_conf into struct ieee80211_key
and thus avoids allocations and having data present twice.
This required some more changes:
1) The removal of the IEEE80211_KEY_DEFAULT_TX_KEY key flag.
This flag isn't used by drivers nor should it be since
we have a set_key_idx() callback. Maybe that callback needs
to be extended to include the key conf, but only a driver that
requires it will tell.
2) The removal of the IEEE80211_KEY_DEFAULT_WEP_ONLY key flag.
This flag is global, so it shouldn't be passed in the key
conf structure. Pass it to the function instead.
Also, this patch removes the AID parameter to the set_key() callback
because it is currently unused and the hardware currently cannot know
about the AID anyway. I suspect this was used with some hardware that
actually selected the AID itself, but that functionality was removed.
Additionally, I've removed the ALG_NULL key algorithm since we have
ALG_NONE.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211, remove bitfields from struct ieee80211_sub_if_data
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211, remove bitfields from struct ieee80211_txrx_data
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove bitfields from struct ieee80211_tx_packet_data
[Johannes: completely clear flags in ieee80211_remove_tx_extra]
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new file event.c that will contain code to send mac/mlme
events to userspace. For now put the Michael MIC failure condition
into it and remove sending of that condition via the management
interface, hostapd interestingly doesn't do anything when it gets
such a packet besides printing a message, it reacts only on the
private iwevent.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing key selection for software decryption, mac80211 gets
a few things wrong: it always uses pairwise keys if configured,
even if the frame is addressed to a multicast address. Also, it
doesn't allow using a key index of zero if a pairwise key has
also been found.
This patch changes the key selection code to be (more) in line
with the 802.11 specification. I have confirmed that with this,
multicast frames are correctly decrypted and I've tested with
WEP as well.
While at it, I've cleaned up the semantics of the hardware flags
IEEE80211_HW_WEP_INCLUDE_IV and IEEE80211_HW_DEVICE_HIDES_WEP
and clarified them in the mac80211.h header; it is also now
allowed to set the IEEE80211_HW_DEVICE_HIDES_WEP option even if
it only applies to frames that have been decrypted by the hw,
unencrypted frames must be dropped but encrypted frames that
the hardware couldn't handle can be passed up unmodified.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Neither hostapd nor wpa_supplicant really use it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many if not all of these messages can be triggered by sending
a few rogue frames which is trivially done and then we overflow
our logs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Woodhouse noticed that under some circumstances the number of slab
allocations kept growing. After looking a bit, this seemed to happen
when you had a management mode interface that was *down*.
The reason for this is that when the device is down, all management
frames get queued to the in-kernel MLME (via ieee80211_sta_rx_mgmt) but
then the sta work is invoked but doesn't run when the netif is down.
When you then bring the interface up, all such frames are freed, but if
you change the mode all of them are lost because the skb queue is
reinitialised as soon as you go back to managed mode. The skb queue is
correctly cleared when the interface is brought down, but the code
doesn't account for the fact that it may be filled while it is not up.
This patch should fix the issue by simply ignoring all interfaces that
are down when going through the RX handlers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some more outdenting to make the code more readable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pre_rx handlers can't really touch sta since for IBSS it might not be
assigned yet, it can create sta info structs on-the-fly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The really indented part that does the huge switch on the interface
type is a nuisance. Put it into an own function 'prepare_for_handlers'.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee80211_rx_h_check handler really does two things, it's
a lot easier to understand if it's split into ieee80211_rx_h_check
and ieee80211_rx_h_load_key, and it may be possible in the future
to optimise the key loading to not do it for each interface.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make some really indented code more readable by outdenting.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the QoS handlers into rx.c making it possible
to compile wme.c only when NET_SCHED is defined.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
