This patch adds an LED driver to support the Dell Activity LED on the
Dell Latitude 2100 netbook and future products to come. The Activity LED
is visible externally in the lid so classroom instructors can observe it
from a distance. The driver uses the sysfs led_class and provides a
standard LED interface.
Signed-off by: Bob Rodgers <Robert_Rodgers@dell.com>
Signed-off-by: Louis Davis <Louis_Davis@dell.com>
Signed-off-by: Jim Dailey <Jim_Dailey@dell.com>, Developers
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Remove the need for "depends on LEDS_CLASS" by wrapping the affected
config options in an if/endif block. Similar for "depends on LEDS_TRIGGERS".
LEDS_COBALT_RAQ still has a "depends on LEDS_CLASS=y" since it cannot
be selected to build as a module.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The ALIX2 LED driver and the CS5535 GPIO drivers share the same I/O
range which causes a conflict if they're both enabled. Fix this for now
by adding Kconfig dependencies. While at it, also drop the EXPERIMENTAL
flag, as the code has been around for awhile already.
Note that this is a hack. At some point, a real platform support for
this board should be added which handles the LEDs via the leds-gpio
driver.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Enable led sub device in Marvell 88PM860x. Two LED arrays can be supported.
Each LED array can be used for R,G,B leds.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides an interface for controlling LEDs (or vibrators)
connected to PMICs for which there is a regulator framework driver.
This driver can be used, for instance, to control vibrator on all Motorola EZX
phones using the pcap-regulator driver services.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The LT3593 is a step-up DC/DC converter designed to drive up to ten
white LEDs in series. The current flow can be set with a control pin.
This driver controls any number of such devices connected on generic
GPIOs and exports the function as as platform_driver.
The gpio_led platform data struct definition is reused for this purpose.
Successfully tested on a PXA embedded board.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This code is based on a driver that came in the "Open-source
and GPL components" download here:
http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Server+Products&ProductLine=Intel%C2%AE+Storage+Systems&ProductProduct=Intel%C2%AE+Entry+Storage+System+SS4200-E&OSVersion=OS+Independent
It was in a file called nasgpio.c inside of a second zip file
called SS4200-E_Linux_SIO_Driver-v1.4.zip and is based on this
updated to use the LED subsystem with the ioctl and hardware
monitor support removed.
I don't have any need for brightness
control, and its code is *completely* separate from the on/off
controls implemented here. If anyone else wants it, I'd be
happy to look into adding it, but I don't care enough for now.
Except for the probe routines, I rewrote most of it. I also
Note that I don't have any hardware documentation except for
the original driver.
Thanks go to Arjan for his help in getting the original source
for this released and for chasing down some licensing issues.
Signed-off-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The WM831x devices feature two software controlled status LEDs with
hardware assisted blinking.
The device can also autonomously control the LEDs based on a selection
of sources. This can be configured at boot time using either platform
data or the chip OTP. A sysfs file in the style of that for triggers
allowing the control source to be configured at run time. Triggers
can't be used here since they can't depend on the implementation details
of a specific LED type.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
LEDs driver for National Semiconductor LP3944 Funlight Chip
http://www.national.com/pf/LP/LP3944.html
This helper chip can drive up to 8 leds, with two programmable DIM
modes; it could even be used as a gpio expander but this driver assumes
it is used as a led controller.
The DIM modes are used to set _blink_ patterns for leds, the pattern is
specified supplying two parameters:
- period: from 0s to 1.6s
- duty cycle: percentage of the period the led is on, from 0 to 100
LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
leds, the camera flash light and the displays backlights.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add initialisation of GPIO ports for compatibility with boards with Award
BIOS (e.g. ALIX.3D3).
Signed-off-by: Tobias Mueller <Tobias_Mueller@twam.info>
Reviewed-by: Constantin Baranov <const@mimas.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
LP5521 is a three channel led driver with support
for hardware accelerated patterns (currently used
via lp5521-only sysfs interface).
Currently, it's used on n810 device.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
ROHM BD2802GU is a RGB LED controller attached to i2c bus and specifically
engineered for decoration purposes. This RGB controller incorporates
lighting patterns and illuminates.
This driver is designed to minimize power consumption, so when there is no
emitting LED, it enters to reset state. And because the BD2802GU has lots
of features that can't be covered by the current LED framework, it
provides Advanced Configuration Function(ADF) mode, so that user
applications can set registers of BD2802GU directly.
Here are basic usage examples :
; to turn on LED (not blink)
$ echo 1 > /sys/class/leds/led1_R/brightness
; to blink LED
$ echo timer > /sys/class/leds/led1_R/trigger
$ echo 1 > /sys/class/leds/led1_R/delay_on
$ echo 1 > /sys/class/leds/led1_R/delay_off
; to turn off LED
$ echo 0 > /sys/class/leds/led1_R/brightness
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Kim Kyuwon <chammoru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The leds-clevo-mail driver is in the mainline kernel since 2.6.25 and works
without severe problems. Make this driver available for a larger audience.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The gpio led trigger will allow leds to be triggered by
gpio events.
When we give the led a gpio number, the trigger will
request_irq() on that so we don't have to keep polling
for gpio state.
It's useful for usecases as n810's keypad leds that could
be triggered by the gpio event generated when user slides
up to show the keypad.
We also provide means for userland to tell us what is the
desired brightness for that special led when it goes on
so userland could use information from ambient light sensors
and not set led brightness too high if it's not necessary.
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Mikrotik built six LEDs into the Routerboard 532, from which one is
destined for custom use, the so called "User LED". This patch adds a
driver for it, based on the LEDs class.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add a simple driver for pwm driver LEDs. pwm_id and period can be defined
in board file. It is developed for pxa, however it is probably generic
enough to be used on other platforms with pwm.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add an LED driver using the DAC124S085 DAC from NatSemi
[randy.dunlap@oracle.com: use header files for interfaces]
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add bindings to support LEDs defined as of_platform devices in addition to
the existing bindings for platform devices.
New options in Kconfig allow the platform binding code and/or the
of_platform code to be turned on. The of_platform code is of course only
available on archs that have OF support.
The existing probe and remove methods are refactored to use new functions
create_gpio_led(), to create and register one led, and delete_gpio_led(),
to unregister and free one led. The new probe and remove methods for the
of_platform driver can then share most of the common probe and remove code
with the platform driver.
The suspend and resume methods aren't shared, but they are very short. The
actual led driving code is the same for LEDs created by either binding.
The OF bindings are based on patch by Anton Vorontsov
<avorontsov@ru.mvista.com>. They have been extended to allow multiple LEDs
per device.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Kernel module providing implementation of LED netfilter target. Each
instance of the target appears as a led-trigger device, which can be
associated with one or more LEDs in /sys/class/leds/
Signed-off-by: Adam Nielsen <a.nielsen@shikadi.net>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Move the second part of the HP laptop disk protection functionality (a red
led) to the same driver. From a purely Linux developer's point of view,
the led and the accelerometer have nothing related. However, they
correspond to the same ACPI functionality, and so will always be used
together, moreover as they share the same ACPI PNP alias, there is no
other simple to allow to have same loaded at the same time if they are not
in the same module. Also make it requires the led class to compile and
update the Kconfig text.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The voltage and current regulators on the WM8350 AudioPlus PMIC can be
used in concert to provide a power efficient LED driver. This driver
implements support for this within the standard LED class.
Platform initialisation code should configure the LED hardware in the
init callback provided by the WM8350 core driver. The callback should
use wm8350_isink_set_flash(), wm8350_dcdc25_set_mode() and
wm8350_dcdc_set_slot() to configure the operating parameters of the
regulators for their hardware and then then use wm8350_register_led() to
instantiate the LED driver.
This driver was originally written by Liam Girdwood, though it has been
extensively modified since then.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Driver for PC Engines ALIX.2 and ALIX.3 LEDs.
Signed-off-by: Constantin Baranov <const@mimas.ru>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
HP notebooks contain accelerometer-based disk protection subsystem,
and LED that indicates hard disk is protected. This is driver for the
LED part.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The cm-x270 board uses leds-gpio so remove the now unneeded driver.
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This allows LEDs to be controlled as a backlight device where
they turn off and on when the display is blanked and unblanked.
This is useful where you need various key backlight LEDs to
dim at the same time as the backlight.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-spitz
Drop leds-spitz.c and the declarations of now un-referenced
spitzscoop_device, spitzscoop2_device.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-corgi
Drop leds-corgi.c and remove the declaration of now un-referenced
corgiscoop_device.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This driver supports the PCA9550, PCA9551, PCA9552, and PCA9553
LED driver chips.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
NXP pca9532 is a LED dimmer/controller attached to i2c bus. It allows
attaching upto 16 leds which can either be on, off or dimmed and/or blinked
with the two PWM modulators available.
This driver is a "new-style" i2c driver that adheres to the driver model and
implements the led framework api. Since the leds connected to the driver are
platform specific, it is only useful when platform data is passed to the
driver to define what leds are connected to which pins.
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Add a trigger which allows LEDs to default to the full
brightness state.
Signed-off-by: Nick Forbes <Nick.Forbes@huntsworth.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
The LEDs on the Freecom FSG-3 are connected to an external
memory-mapped latch on the ixp4xx expansion bus, and therefore cannot
be supported by any of the existing LEDs drivers.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
The leds-clevo-mail module also works with model "Clevo D400P",
add this model to the white list.
Signed-off-by: Mrton Nmeth <nm127@freemail.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
iwlwifi: Fix built-in compilation of iwlcore
net: Unexport move_addr_to_{kernel,user}
rt2x00: Select LEDS_CLASS.
iwlwifi: Select LEDS_CLASS.
leds: Do not guard NEW_LEDS with HAS_IOMEM
[IPSEC]: Fix catch-22 with algorithm IDs above 31
time: Export set_normalized_timespec.
tcp: Make use of before macro in tcp_input.c
hamradio: Remove unneeded and deprecated cli()/sti() calls in dmascc.c
[NETNS]: Remove empty ->init callback.
[DCCP]: Convert do_gettimeofday() to getnstimeofday().
[NETNS]: Don't initialize err variable twice.
[NETNS]: The ip6_fib_timer can work with garbage on net namespace stop.
[IPV4]: Convert do_gettimeofday() to getnstimeofday().
[IPV4]: Make icmp_sk_init() static.
[IPV6]: Make struct ip6_prohibit_entry_template static.
tcp: Trivial fix to correct function name in a comment in net/ipv4/tcp.c
[NET]: Expose netdevice dev_id through sysfs
skbuff: fix missing kernel-doc notation
[ROSE]: Fix soft lockup wrt. rose_node_list_lock
The LEDS infrastructure itself does not require anything
that a platform dependant upon HAS_IOMEM.
The individual drivers do, but they are properly guarded
with the necessary platform dependencies.
One can even imagine a hypervisor based LED driver that
a platform without HAS_IOMEM might have.
Signed-off-by: David S. Miller <davem@davemloft.net>
As now tosa uses leds-gpio, drop leds-tosa driver.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a LED driver using the PWM on newer SOCs from Atmel; brightness is
controlled by changing the PWM duty cycle. So for example if you've set up
two leds labeled "pwm0" and "pwm1":
echo 0 > /sys/class/leds/pwm2/brightness # off (0%)
echo 80 > /sys/class/leds/pwm2/brightness
echo 255 > /sys/class/leds/pwm2/brightness # on (100%)
Note that "brightness" here isn't linear; maybe that should change. Going
from 4 to 8 probably doubles perceived brightness, while 244 to 248 is
imperceptible.
This is mostly intended to be a simple example of PWM, although it's
realistic since LCD backlights are often driven with PWM to conserve
battery power (and offer brightness options).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the LEDs on the HP Jornada 620/660/680/690 devices.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
All boards using the IXP4XX-GPIO-LED driver have been updated to use
the generic leds-gpio driver instead.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Add support for hardware accelerated LED blinking for the mail LED
commonly found on Clevo notebooks.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Extends the leds subsystem with a blink_set() callback function which can
be optionally implemented by a LED driver. If implemented, the driver can use
the hardware acceleration for blinking a LED.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
