In 3.7 the 8250 module name was changed unintentionally from 8250 to
8250_core by commit 835d844d1a
(8250_pnp: do pnp probe before legacy probe). We then had to
re-introduce the old module options to ensure the old good
8250.nr_uart & co. still work. This can be done only by a very dirty
hack and we did it in f2b8dfd9e4
(serial: 8250: Keep 8250.<xxxx> module options functional after driver
rename).
That is so damn ugly so that I decided to revert to the old module
name and deprecate the new 8250_core options present in 3.7 and 3.8
only. The deprecation will happen in the following patch.
Note that this patch changes the hack above to support "8250_core.*",
because we now have "8250.*" natively.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in 8250.c for detecting ARM/XScale UARTs says:
* Try writing and reading the UART_IER_UUE bit (b6).
* If it works, this is probably one of the Xscale platform's
* internal UARTs.
If the above passes, it then goes on to:
* It's an Xscale.
* We'll leave the UART_IER_UUE bit set to 1 (enabled).
However, the CH352 uses the UART_IER_UUE as the LOWPOWER function,
so it is readable and writable. According to the datasheet:
"LOWPOWER:When the bit is 1, close the internal benchmark
clock of serial port to set into low-power status.
So it essentially gets mis-detected as Xscale, and gets
powered down in the process. The device in question where
this was seen is listed by lspci as:
Serial controller: Device 4348:3253 (rev 10) (prog-if 02 [16550])
Re-using the 353 quirk which just sets flags to fixed and type
to 16550 is suitable for fixing the 352 as well.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Index of atmel_ports[ATMEL_MAX_UART] should be smaller
than ATMEL_MAX_UART.
Signed-off-by: Pawel Wieczorkiewicz <wpawel@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig symbol SERIAL_S3C2412 got removed in commit
da121506eb ("serial: samsung: merge
probe() function from all SoC specific extensions"). But it also added a
last reference to that symbol. The commit and the tree make clear that
CPU_S3C2412 should have been used instead.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 835d844d1 (8250_pnp: do pnp probe before legacy probe), the
8250 driver was renamed to 8250_core. This means any existing usage of
the 8259.<xxxx> module parameters or as a kernel command line switch is
now broken, as the 8250_core driver doesn't parse options belonging to
something called "8250".
To solve this, we redefine the module options in a dummy function using
a redefined MODULE_PARAM_PREFX when built into the kernel. In the case
where we're building as a module, we provide an alias to the old 8250
name. The dummy function prevents compiler errors due to global variable
redefinitions that happen as part of the module_param_ macro expansions.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This could have been either ARCH_S5P64X0 or CPU_S5P6450. Looking at
commit 2555e663b3 ("ARM: S5P64X0: Add UART
serial support for S5P6450") - which added this typo - makes clear this
should be CPU_S5P6450.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The InsydeH2O BIOS (version dated 09/12/2011) has the following in
its pnp resouces for its serial ports:
$ cat /sys/bus/pnp/devices/00:0b/resources
state = active
io disabled
irq disabled
We do not check if the resources are disabled, and create a bogus
ttyS* device. Since commit 835d844d1a (8250_pnp: do pnp probe
before legacy probe) we get a bogus ttyS0, which prevents the legacy
probe from detecting it.
Note, the BIOS can also be upgraded, fixing this problem, but for people
who can't do that, this fix is needed.
Reported-by: Vincent Deffontaines <vincent@gryzor.com>
Tested-by: Vincent Deffontaines <vincent@gryzor.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
92a19f9cec introduced a local variable
with the same name as the argument to bcm_uart_do_rx, breaking
compilation. Fix this by renaming the new variable and its uses where
expected.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've managed to find an 8 port version of the card 4 port card which was discussed here:
http://marc.info/?l=linux-serial&m=120760744205314&w=2
Looking back at that thread there were two issues in the original patch.
1) The I/O ports for the UARTs are within BAR2 not BAR0. This can been seen in the original post.
2) A serial quirk isn't needed as these cards have no memory in BAR0 which makes pci_plx9050_init just return.
This patch fixes the 4 port support to use BAR2, removes the bogus quirk and adds support for the 8 port card.
$ lspci -vvv -n -s 00:08.0
00:08.0 0780: 10b5:9050 (rev 01)
Subsystem: 10b5:1588
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 17
Region 1: I/O ports at ff00 [size=128]
Region 2: I/O ports at fe00 [size=64]
Region 3: I/O ports at fd00 [size=8]
Capabilities: <access denied>
Kernel driver in use: serial
$ dmesg | grep 0000:00:08.0:
[ 0.083320] pci 0000:00:08.0: [10b5:9050] type 0 class 0x000780
[ 0.083355] pci 0000:00:08.0: reg 14: [io 0xff00-0xff7f]
[ 0.083369] pci 0000:00:08.0: reg 18: [io 0xfe00-0xfe3f]
[ 0.083382] pci 0000:00:08.0: reg 1c: [io 0xfd00-0xfd07]
[ 0.083460] pci 0000:00:08.0: PME# supported from D0 D3hot
[ 1.212867] 0000:00:08.0: ttyS4 at I/O 0xfe00 (irq = 17) is a 16550A
[ 1.233073] 0000:00:08.0: ttyS5 at I/O 0xfe08 (irq = 17) is a 16550A
[ 1.253270] 0000:00:08.0: ttyS6 at I/O 0xfe10 (irq = 17) is a 16550A
[ 1.273468] 0000:00:08.0: ttyS7 at I/O 0xfe18 (irq = 17) is a 16550A
[ 1.293666] 0000:00:08.0: ttyS8 at I/O 0xfe20 (irq = 17) is a 16550A
[ 1.313863] 0000:00:08.0: ttyS9 at I/O 0xfe28 (irq = 17) is a 16550A
[ 1.334061] 0000:00:08.0: ttyS10 at I/O 0xfe30 (irq = 17) is a 16550A
[ 1.354258] 0000:00:08.0: ttyS11 at I/O 0xfe38 (irq = 17) is a 16550A
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Altera 8250/16550 compatible serial port.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the extra code left over when the serial driver was changed
to require a clock. There is no fallback to 24Mhz as a clock is
now required.
Also remove a second call to of_clk_get which is unnecessary.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mpc512x platform clock code names PSC clocks as "pscX_mclk" but
the driver tries to get "pscX_clk" clock and this results in
errors like:
mpc52xx-psc-uart 80011700.psc: Failed to get PSC clock entry!
The problem appears when opening ttyPSC devices other than the
system's serial console. Since getting and enabling the PSC clock
fails, uart port startup doesn't succeed and tty flag TTY_IO_ERROR
remains set causing further errors in tty ioctls, i.e.
'strace stty -F /dev/ttyPSC1' shows:
open("/dev/ttyPSC1", O_RDONLY|O_NONBLOCK|O_LARGEFILE) = 3
dup2(3, 0) = 0
close(3) = 0
fcntl64(0, F_GETFL) = 0x10800 (flags O_RDONLY|O_NONBLOCK|O_LARGEFILE)
fcntl64(0, F_SETFL, O_RDONLY|O_LARGEFILE) = 0
ioctl(0, TCGETS, 0xbff89038) = -1 EIO (Input/output error)
Only request PSC clock names that the platform actually provides.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull MIPS updates from Ralf Baechle:
o Add basic support for the Mediatek/Ralink Wireless SoC family.
o The Qualcomm Atheros platform is extended by support for the new
QCA955X SoC series as well as a bunch of patches that get the code
ready for OF support.
o Lantiq and BCM47XX platform have a few improvements and bug fixes.
o MIPS has sent a few patches that get the kernel ready for the
upcoming microMIPS support.
o The rest of the series is made up of small bug fixes and cleanups
that relate to various parts of the MIPS code. The biggy in there is
a whitespace cleanup. After I was sent another set of whitespace
cleanup patches I decided it was the time to clean the whitespace
"issues" for once and and that touches many files below arch/mips/.
Fix up silly conflicts, mostly due to whitespace cleanups.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (105 commits)
MIPS: Quit exporting kernel internel break codes to uapi/asm/break.h
MIPS: remove broken conditional inside vpe loader code
MIPS: SMTC: fix implicit declaration of set_vi_handler
MIPS: early_printk: drop __init annotations
MIPS: Probe for and report hardware virtualization support.
MIPS: ath79: add support for the Qualcomm Atheros AP136-010 board
MIPS: ath79: add USB controller registration code for the QCA955X SoCs
MIPS: ath79: add PCI controller registration code for the QCA955X SoCs
MIPS: ath79: add WMAC registration code for the QCA955X SoCs
MIPS: ath79: register UART for the QCA955X SoCs
MIPS: ath79: add QCA955X specific glue to ath79_device_reset_{set, clear}
MIPS: ath79: add GPIO setup code for the QCA955X SoCs
MIPS: ath79: add IRQ handling code for the QCA955X SoCs
MIPS: ath79: add clock setup code for the QCA955X SoCs
MIPS: ath79: add SoC detection code for the QCA955X SoCs
MIPS: ath79: add early printk support for the QCA955X SoCs
MIPS: ath79: fix WMAC IRQ resource assignment
mips: reserve elfcorehdr
mips: Make sure kernel memory is in iomem
MIPS: ath79: use dynamically allocated USB platform devices
...
Conflicts:
include/linux/ssb/ssb_driver_gige.h
Also resolves a logical merge conflict in drivers/net/ethernet/broadcom/-
bgmac.c due to change of an API.
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
Pull workqueue [delayed_]work_pending() cleanups from Tejun Heo:
"This is part of on-going cleanups to remove / minimize usages of
workqueue interfaces which are deprecated and/or misleading.
This round drops a number of usages of [delayed_]work_pending(), which
are dangerous as they lack any form of synchronization and thus often
lead to buggy / unnecessary code. There are a couple legitimate use
cases in kernel. Hopefully, they can be converted and
[delayed_]work_pending() can be removed completely. Even if not,
removing most of misuses should make it more difficult to find
examples of misuses and thus slow down growth of them.
These changes are independent from other workqueue changes."
* 'for-3.9-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
wimax/i2400m: fix i2400m->wake_tx_skb handling
kprobes: fix wait_for_kprobe_optimizer()
ipw2x00: simplify scan_event handling
video/exynos: don't use [delayed_]work_pending()
tty/max3100: don't use [delayed_]work_pending()
x86/mce: don't use [delayed_]work_pending()
rfkill: don't use [delayed_]work_pending()
wl1251: don't use [delayed_]work_pending()
thinkpad_acpi: don't use [delayed_]work_pending()
mwifiex: don't use [delayed_]work_pending()
sja1000: don't use [delayed_]work_pending()
Commit 677fe55 (serial: imx: Fix recursive locking bug) introduces an
uninitialized variable warning as below.
CC drivers/tty/serial/imx.o
drivers/tty/serial/imx.c: In function ‘imx_console_write’:
include/linux/spinlock.h:340:2: warning: ‘flags’ may be used uninitialized in this function [-Wuninitialized]
drivers/tty/serial/imx.c:1214:16: note: ‘flags’ was declared here
Initialize the variable to suppress the warning.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra only supports, and always enables, device tree. Remove all ifdefs
for DT support from the driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ec1882df2 (tty: serial: imx: console write routing is unsafe
on SMP) introduced a recursive locking bug in imx_console_write().
The callchain is:
imx_rxint()
spin_lock_irqsave(&sport->port.lock,flags);
...
uart_handle_sysrq_char();
sysrq_function();
printk();
imx_console_write();
spin_lock_irqsave(&sport->port.lock,flags); <--- DEAD
The bad news is that the kernel debugging facilities can dectect the
problem, but the printks never surface on the serial console for
obvious reasons.
There is a similar issue with oops_in_progress. If the kernel crashes
we really don't want to be stuck on the lock and unable to tell what
happened.
In general most UP originated drivers miss these checks and nobody
ever notices because CONFIG_PROVE_LOCKING seems to be still ignored by
a large number of developers.
The solution is to avoid locking in the sysrq case and trylock in the
oops_in_progress case.
This scheme is used in other drivers as well and it would be nice if
we could move this to a common place, so the usual copy/paste/modify
bugs can be avoided.
Now there is another issue with this scheme:
CPU0 CPU1
printk()
rxint()
sysrq_detection() -> sets port->sysrq
return from interrupt
console_write()
if (port->sysrq)
avoid locking
port->sysrq is reset with the next receive character. So as long as
the port->sysrq is not reset and this can take an endless amount of
time if after the break no futher receive character follows, all
console writes happen unlocked.
While the current writer is protected against other console writers by
the console sem, it's unprotected against open/close or other
operations which fiddle with the port. That's what the above mentioned
commit tried to solve.
That's an issue in all drivers which use that scheme and unfortunately
there is no easy workaround. The only solution is to have a separate
indicator port->sysrq_cpu. uart_handle_sysrq_char() then sets it to
smp_processor_id() before calling into handle_sysrq() and resets it to
-1 after that. Then change the locking check to:
if (port->sysrq_cpu == smp_processor_id())
locked = 0;
else if (oops_in_progress)
locked = spin_trylock_irqsave(port->lock, flags);
else
spin_lock_irqsave(port->lock, flags);
That would force all other cpus into the spin_lock path. Problem
solved, but that's way beyond the scope of this fix and really wants
to be implemented in a common function which calls the uart specific
write function to avoid another gazillion of hard to debug
copy/paste/modify bugs.
Reported-and-tested-by: Tim Sander <tim@krieglstein.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable <stable@vger.kernel.org> # 3.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hardpps() functionality is provided through the N_PPS line
discipline now. The new function signature was added in commit
025b40ab (2011-01-12). There was no previous macro or
function hardpps(), at least since before the initial commit of
v2.6.12 in 2005. It's unlikely this code has been compiled since.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An extension of the previous commit, there is no semantic change
here, just fewer lines of source code.
Signed-off-by: George Spelvin <linux@horizon.com>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PPS (Pulse-Per-Second) line discipline has developed a number of
unhealthy attachments to core tty data and functions, ultimately leading
to its breakage.
The previous patches fixed the crashing. This one reduces coupling further
by eliminating the timestamp parameter from the dcd_change ldisc method.
This reduces header file linkage and makes the extension more generic,
and the timestamp read is delayed only slightly, from just before the
ldisc->ops->dcd_change method call to just after.
Fix attendant build breakage in
drivers/tty/n_tty.c
drivers/tty/tty_buffer.c
drivers/staging/speakup/selection.c
drivers/staging/dgrp/dgrp_*.c
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@braille.uwo.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: George Spelvin <linux@horizon.com>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use big and little endian accessors function to reflect system configuration.
Detection is done via control register in ulite_request_port.
Tested on Microblaze LE, BE, PPC440 and Arm zynq.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since SERIAL_CORE needs GENERIC_HARDIRQS (see below) and most serial drivers
select it, just add a GENERIC_HARDIRQS dependency to all serial drivers.
Fixes the compile error below:
drivers/tty/serial/serial_core.c: In function ‘uart_set_info’:
drivers/tty/serial/serial_core.c:725:2: error: implicit declaration of function ‘irq_canonicalize’
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cdc8da3998.
In my attempt to fix a build warning on arm randconfig a build error on
imx_v6_v7_defconfig was introduced, so revert it for now.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_CONSOLE_POLL is not defined, the following build warning happens:
drivers/tty/serial/imx.c:274:13: warning: 'imx_port_ucrs_save' defined but not used [-Wunused-function]
drivers/tty/serial/imx.c:283:13: warning: 'imx_port_ucrs_restore' defined but not used [-Wunused-function]
Move imx_port_ucrs_saver/restore under CONFIG_CONSOLE_POLL ifdef block to fix it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need for two separate return statements, consolidate them.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need for two separate return statements, consolidate them.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Original configuration of Rx FIFO threshold contained an error
that resulted Rx threshold to be effectively set to 1 character
instead of 16 characters, as noted in comments.
Checking LSR to contain UART_LSR_THRE bit set caused issue when
not all UART_IER_THRI interrupts have been properly handled.
This caused gap in Tx data, visible on high baud rates using
oscilloscope.
Setting OMAP_UART_SCR_TX_EMPTY bit in SCR caused UART_IER_THRI
interrupt to be raised only when Tx FIFO and Tx shift registers
are empty.
Signed-off-by: Alexey Pelykh <alexey.pelykh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra is only booted through device-tree now; there are no board files
left that use this function. Hence, don't export it. Move the static
inline definition into of_serial.c, so we can delete of_serial.h too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no reason kgdb.h itself needs to include the 8250 serial port
header file. So push it down to the _very_ limited number of individual
drivers that need the values in that file, and fix up the places where
people really wanted serial_core.h and platform_device.h.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MIPS based Ralink WiSoC platform has 1 or more 8250 compatible serial cores.
To make them work we require the same quirks that are used by AU1x00.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for later SUNIX (TIMEDIA) Universal PCI Single and Multi-Port
Communications Boards.
These boards have PCI Vendor ID 1fd4 with device ID 1999 but otherwise
appear to be the same as the TIMEDIA boards already supported by 8250_pci
and parport_serial.
Tested with:
a. the two port serial board part number SER5037A,
b. the two port serial and one port parallel board part number
MIO5079A.
Signed-off-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When PCH_UART_CONSOLE and SERIAL_CORE_CONSOLE is not set neither, the
uart_port will have no 'sysrq' member hence their will need a '#ifdef'
in pch_uart.c to handle the case, otherwise we'll see compile error
like this:
CC [M] drivers/tty/serial/pch_uart.o
drivers/tty/serial/pch_uart.c: In function 'pch_uart_hal_read':
drivers/tty/serial/pch_uart.c:572:11: error: 'struct uart_port' has no member named 'sysrq'
make[4]: *** [drivers/tty/serial/pch_uart.o] Error 1
Reported-by: Randy Dunlap <rdunlap@infradead.org>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Liang Li <liang.li@windriver.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__exit_p() need to be removed after the __devexit
removal from the driver.
Warning log:
drivers/tty/serial/xilinx_uartps.c:996:12:
warning: 'xuartps_remove' defined but not used [-Wunused-function]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to memset 0 to SPI frame memory before preparing
transfer frame bits, because SPI frame header are encoded with valid
data size, so don't need to worry about adopting dirty bits, more,
memset zero for each SPI frame may impact the spi throughput efficiency.
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This struct is used only for driver, so it should be static.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a hardware reset the break and overflow bits for
these events. Without resetting the bits they will be reported to
the core every time, when once occur.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The non-dt probing allowed passing the location via platform data from
the beginning. So make up leeway for device tree probing.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for specifying clock information for the uart clk via the
device tree. This eliminates the need to hardcode rates in the device
tree.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
