Commit graph

1046 commits

Author SHA1 Message Date
Joachim Fenkes
0455e36d81 IB/ehca: Make some module parameters bool, update descriptions
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-23 11:55:45 -07:00
Joachim Fenkes
a7607c9b11 IB/ehca: Remove mr_largepage parameter
Always enable large page support; didn't seem to cause problems for anyone.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-23 11:55:45 -07:00
Joachim Fenkes
4da27d6d5b IB/ehca: Move high-volume debug output to higher debug levels
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-23 11:55:45 -07:00
Joachim Fenkes
863fb09fbf IB/ehca: Prevent posting of SQ WQEs if QP not in RTS
...as required by IB Spec, C10-29.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-23 11:55:45 -07:00
Chien Tung
bc5698f3ec RDMA/nes: Fix adapter reset after PXE boot
After PXE boot, the iw_nes driver does a full reset to ensure the card
is in a clean state.  However, it doesn't wait for firmware to
complete its work before issuing a port reset to enable the ports,
which leads to problems bringing up the ports.

The solution is to wait for firmware to complete its work before
proceeding with port reset.

This bug was flagged by Roland Dreier <rolandd@cisco.com>.

Cc: <stable@kernel.org>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-23 11:55:45 -07:00
Roland Dreier
e447703123 RDMA/nes: Print IPv4 addresses in a readable format
Use NIPQUAD_FMT instead of printing raw 32-bit hex quantities in
debugging output.

Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-23 11:55:43 -07:00
Roland Dreier
2bd01c5d2e RDMA/nes: Use print_mac() to format ethernet addresses for printing
Removing open-coded MAC formats shrinks the source and the generated
code too, eg on x86-64:

add/remove: 0/0 grow/shrink: 0/4 up/down: 0/-103 (-103)
function                                     old     new   delta
make_cm_node                                 932     912     -20
nes_netdev_set_mac_address                   427     406     -21
nes_netdev_set_multicast_list               1148    1124     -24
nes_probe                                   2349    2311     -38

Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-23 11:52:18 -07:00
Roland Dreier
bc751fe6ff IB/ipath: Correct capitalization "IntX" -> "INTx"
Match what the PCI specification uses.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-21 18:19:15 -07:00
Roland Dreier
44957572cc IB/ipath: Remove tests of PCI_MSI in ipath_iba7220.c
The PCI MSI interface is stubbed out properly so that all the
functions just return failure if PCI_MSI=n, so there's no reason to
have "#ifdef CONFIG_PCI_MSI" blocks in ipath_iba7220.c.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-21 18:19:15 -07:00
Roland Dreier
480f58e614 IB/ipath: Remove dependency on PCI_MSI || HT_IRQ
Before IBA7220 support was added, the ipath driver didn't support any
hardware unless PCI_MSI and/or HT_IRQ was enabled.  However, the
IBA7220 can generate INTx interrupts, so it makes sense to allow the
driver to be build even if PCI_MSI=n and HT_IRQ=n.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-21 18:19:14 -07:00
Roland Dreier
37a6ab5227 IB/ipath: Build IBA7220 code unconditionally
The new IBA7220 code added a call to ipath_init_iba7220_funcs() that
is compiled unconditionally, but only built the IBA7220 code if
PCI_MSI is enabled.  Fix this by building the IBA7220 file
unconditonally.

This fixes build breakage when PCI_MSI=n, HT_IRQ=y and
INFINIBAND_IPATH=y reported by Ingo Molnar <mingo@elte.hu>:

 drivers/built-in.o: In function `ipath_init_one':
 ipath_driver.c:(.devinit.text+0x1e5bc): undefined reference to `ipath_init_iba7220_funcs'

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-21 18:19:14 -07:00
Roland Dreier
88a8317bcd IB/ipath: Remove reference to dev->class_dev
Commit 124b4dcb ("IB/ipath: add calls to new 7220 code and enable in                                
build") inadvertently added core to set dev->class_dev.dev back into                                
ib_ipath.  This is completely redundant since commit 1912ffbb ("IB: Set                             
class_dev->dev in core for nice device symlink"), which removed                                     
class_dev setting from low-level drivers, and also will break the build
when class_dev is removed completely from struct ib_device.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-21 18:19:14 -07:00
Paul Bolle
9862874d21 IB/ipath: Fix module parameter description for disable_sma
Describe disable_sma parameter with its name rather than the internal
ib_ipath_disable_sma variable name, so that the description shows up
properly in modinfo.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-21 18:19:13 -07:00
Roland Dreier
6a5546e76c RDMA/nes: Remove unneeded function declarations
Remove redundant static declarations of functions that are defined
before they are used in the source.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-21 18:19:12 -07:00
Linus Torvalds
e80ab411e5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
  SCSI: convert struct class_device to struct device
  DRM: remove unused dev_class
  IB: rename "dev" to "srp_dev" in srp_host structure
  IB: convert struct class_device to struct device
  memstick: convert struct class_device to struct device
  driver core: replace remaining __FUNCTION__ occurrences
  sysfs: refill attribute buffer when reading from offset 0
  PM: Remove destroy_suspended_device()
  Firmware: add iSCSI iBFT Support
  PM: Remove legacy PM (fix)
  Kobject: Replace list_for_each() with list_for_each_entry().
  SYSFS: Explicitly include required header file slab.h.
  Driver core: make device_is_registered() work for class devices
  PM: Convert wakeup flag accessors to inline functions
  PM: Make wakeup flags available whenever CONFIG_PM is set
  PM: Fix misuse of wakeup flag accessors in serial core
  Driver core: Call device_pm_add() after bus_add_device() in device_add()
  PM: Handle device registrations during suspend/resume
  block: send disk "change" event for rescan_partitions()
  sysdev: detect multiple driver registrations
  ...

Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
2008-04-21 15:49:58 -07:00
Tony Jones
f4e91eb4a8 IB: convert struct class_device to struct device
This converts the main ib_device to use struct device instead of struct
class_device as class_device is going away.

Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-19 19:10:30 -07:00
Matthew Wilcox
6188e10d38 Convert asm/semaphore.h users to linux/semaphore.h
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
2008-04-18 22:22:54 -04:00
Matthew Wilcox
d3135846f6 drivers: Remove unnecessary inclusions of asm/semaphore.h
None of these files use any of the functionality promised by
asm/semaphore.h.  It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
2008-04-18 22:16:32 -04:00
Jack Morgenstein
068c4ea1bb IB/mlx4: Update module version and release date
The mlx4_ib driver is stable enough for production use, so bump the
version number to 1.0 to indicate this.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:35 -07:00
Stefan Roscher
c83b5b1cb2 IB/ehca: Support all ibv_devinfo values in query_device() and query_port()
Also, introduce a few inline helper functions to make the code more readable.

Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:35 -07:00
Roland Dreier
4cd1e5eb3c RDMA/nes: Free IRQ before killing tasklet
Move the free_irq() call in nes_remove() to before the tasklet_kill();
otherwise there is a window after tasklet_kill() where a new interrupt
can be handled and reschedule the tasklet, leading to a use-after-free
crash.

Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:34 -07:00
Jack Morgenstein
940801b27e IB/mthca: Update module version and release date
The ib_mthca driver has been stable for a while, so bump the version
number to 1.0 to indicate this.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:34 -07:00
Dotan Barak
0df6703095 IB/mlx4: Update QP state if query QP succeeds
If the QP was moved to another state (such as SQE) by the hardware,
then after this change the user won't have to set the IBV_QP_CUR_STATE
mask in order to execute modify QP in order to recover from this state.

Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:34 -07:00
Dotan Barak
5121df3ae4 IB/mthca: Update QP state if query QP succeeds
If the QP was moved to another state (such as SQE) by the hardware,
then after this change the user won't have to set the IBV_QP_CUR_STATE
mask in order to execute modify QP in order to recover from this state.

Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:34 -07:00
Tom Tucker
9285faa1e7 RDMA/amso1100: Add check for NULL reply_msg in c2_intr()
Fix a place where we might dereference a NULL pointer; this fixes
Coverity CID 1392.  On inspection I also found a place where we could
attempt to kmem_cache_free() a NULL pointer, so fix this too.

Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:34 -07:00
Vladimir Sokolovsky
bbf8eed1a0 IB/mlx4: Add support for resizing CQs
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:33 -07:00
Eli Cohen
3fdcb97f0b IB/mlx4: Add support for modifying CQ moderation parameters
Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:33 -07:00
Roland Dreier
139b2db795 RDMA/amso1100: Add support for "send with invalidate" work requests
Handle IB_WR_SEND_WITH_INV work requests.

This resurrects a patch sent long ago by Mikkel Hagen <mhagen@iol.unh.edu>.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:32 -07:00
Roland Dreier
0f39cf3d54 IB/core: Add support for "send with invalidate" work requests
Add a new IB_WR_SEND_WITH_INV send opcode that can be used to mark a
"send with invalidate" work request as defined in the iWARP verbs and
the InfiniBand base memory management extensions.  Also put "imm_data"
and a new "invalidate_rkey" member in a new "ex" union in struct
ib_send_wr. The invalidate_rkey member can be used to pass in an
R_Key/STag to be invalidated.  Add this new union to struct
ib_uverbs_send_wr.  Add code to copy the invalidate_rkey field in
ib_uverbs_post_send().

Fix up low-level drivers to deal with the change to struct ib_send_wr,
and just remove the imm_data initialization from net/sunrpc/xprtrdma/,
since that code never does any send with immediate operations.

Also, move the existing IB_DEVICE_SEND_W_INV flag to a new bit, since
the iWARP drivers currently in the tree set the bit.  The amso1100
driver at least will silently fail to honor the IB_SEND_INVALIDATE bit
if passed in as part of userspace send requests (since it does not
implement kernel bypass work request queueing).  Remove the flag from
all existing drivers that set it until we know which ones are OK.

The values chosen for the new flag is not consecutive to avoid clashing
with flags defined in the XRC patches, which are not merged yet but
which are already in use and are likely to be merged soon.

This resurrects a patch sent long ago by Mikkel Hagen <mhagen@iol.unh.edu>.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:32 -07:00
Ralph Campbell
e7eacd3686 IB/ipath: Update copyright dates for files changed in 2008
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:32 -07:00
Dave Olson
124b4dcb1d IB/ipath: add calls to new 7220 code and enable in build
This patch adds the initialization calls into the new 7220 HCA files,
changes the Makefile to compile and link the new files, and code to
handle send DMA.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:32 -07:00
Arthur Jones
bb9171448d IB/ipath: Misc changes to prepare for IB7220 introduction
The patch adds a number of minor changes to support newer HCAs:
 - New send buffer control bits
 - New error condition bits
 - Locking and initialization changes
 - More send buffers

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:31 -07:00
Arthur Jones
8babfa4fb9 IB/ipath: User mode send DMA
A new file which allows the IBA7220 send DMA engine to be used from
userland.  The routines here are not linked in yet, that will happen in
a follow-on patch...

Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:31 -07:00
Arthur Jones
909c0faa8f IB/ipath: User mode send DMA header file
A new header file which allows the IBA7220 send DMA engine to be used
from userland.  The definitions here are not used yet, that will happen
in a follow-on patch...

Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:31 -07:00
John Gregor
f7a60d71af IB/ipath: Add code for IBA7220 send DMA
The IBA7220 HCA has a new feature to DMA data to the on chip send
buffers instead of or in addition to the host CPU doing the data
transfer.  This patch adds code to support the send DMA queue.

Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:31 -07:00
Ralph Campbell
2c19643563 IB/ipath: Add IBA7220-specific SERDES initialization data
This patch adds binary data to initialize the IB SERDES.

Signed-off-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:31 -07:00
Michael Albaugh
ab0fb2e049 IB/ipath: Support for SerDes portion of IBA7220
The control and initialization of the SerDes blocks of the IBA7220 is
sufficiently complex to merit a separate file.

Signed-off-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:31 -07:00
Ralph Campbell
843e6ab489 IB/ipath: HCA-specific code to support IBA7220
This patch adds the HCA-specific code for the IBA7220 HCA.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:30 -07:00
Michael Albaugh
dd042d59c1 IB/ipath: Isolate 7220-specific content
This patch adds a new ASIC-specific header file for the HCAs using the IBA7220.

Signed-off-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:30 -07:00
Ralph Campbell
afce688ba9 IB/ipath: Header file changes to support IBA7220
This is part of a patch series to add support for a new HCA.  This patch
adds new fields to the header files.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:30 -07:00
Ralph Campbell
6bb68835d3 IB/ipath: Fix up error handling
This patch makes chip reset more robust and reduces lock contention
between user and kernel TID register updates.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:30 -07:00
Dave Olson
9b436eb4f8 IB/ipath: Fix check for no interrupts to reliably fallback to INTx
Newer HCAs support MSI interrupts and also INTx interrupts.  Fix the
code so that INTx can be reliably enabled if MSI interrupts are not
working.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:30 -07:00
Dave Olson
1d7c2e529f IB/ipath: Enable reduced PIO update for HCAs that support it.
Newer HCAs have a threshold counter to reduce the number of DMAs the
chip makes to update the PIO buffer availability status bits.  This
patch enables the feature.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:30 -07:00
Dave Olson
0ab6b2b9ab IB/ipath: Set LID filtering for HCAs that support it.
Whenever the LID is set, notify the HCA specific code so that the
appropriate HW registers can be updated. Also log the info on the
console at low priority.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:29 -07:00
Dave Olson
b3e8f54107 IB/ipath: Add support for IBTA 1.2 Heartbeat
This patch adds code to enable/disable the IBTA 1.2 heartbeat for testing
if the HCA supports it.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:29 -07:00
Dave Olson
555b203e48 IB/ipath: Make link state transition code ignore (transient) link recovery
The hardware-based recovery doesn't need any intervention, and in a few
cases we can get a bit confused about state and skip steps such as
turning off the link state LED when we consider recovery to be "down".
So ignore this transition, and either we recover in hardware, or we
transition to down, and will handle it then.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:29 -07:00
Ralph Campbell
9355fb6a06 IB/ipath: Add support for 7220 receive queue changes
Newer HCAs have a HW option to write a sequence number to each receive
queue entry and avoid a separate DMA of the tail register to memory.
This patch adds support for these changes.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:29 -07:00
Ralph Campbell
2ba3f56eb4 IB/ipath: Fix some white space and code style issues
This patch makes some white space changes and minor non-functional
changes to more closely match the code in OFED-1.3.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:29 -07:00
Michael Albaugh
afd9970f95 IB/ipath: Allow old and new diagnostic packet formats
This patch checks for old and new format writes to send a packet via the
diagnostic interface.

Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:28 -07:00
Robert P. J. Day
b3b8128fd3 IB/ipath: Fix time comparison to use time_after_eq()
Raw comparison against jiffies will fail if jiffies wraps, although
since ipath currently only supports 64-bit architectures, this is rather
far-fetched.  Still, it's better to use time_after_eq().

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:28 -07:00
Roland Dreier
f438000f7a IB/mlx4: Micro-optimize mlx4_ib_post_send()
Rather than have build_mlx_header() return a negative value on failure
and the length of the segments it builds on success, add a pointer
parameter to return the length and return 0 on success.  This matches
the calling convention used for build_lso_seg() and generates slightly
smaller code -- eg, on 64-bit x86:

add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-22 (-22)
function                                     old     new   delta
mlx4_ib_post_send                           2023    2001     -22

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:28 -07:00
Eli Cohen
b832be1e40 IB/mlx4: Add IPoIB LSO support
Add TSO support to the mlx4_ib driver.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:27 -07:00
Eli Cohen
b846f25aa2 IB/core: Add creation flags to struct ib_qp_init_attr
Add a create_flags member to struct ib_qp_init_attr that will allow a
kernel verbs consumer to create a pass special flags when creating a QP.
Add a flag value for telling low-level drivers that a QP will be used
for IPoIB UD LSO.  The create_flags member will also be useful for XRC
and ehca low-latency QP support.

Since no create_flags handling is implemented yet, add code to all
low-level drivers to return -EINVAL if create_flags is non-zero.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:27 -07:00
Michael Albaugh
d84e0b28d3 IB/ipath: EEPROM support for 7220 devices, robustness improvements, cleanup
Add support for reading newer card's EEPROMs while continuing to support
older EEPROMs.

Also, add support for the temperature sensor if present.

Signed-off-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:27 -07:00
Ralph Campbell
d98b193776 IB/ipath: Use PIO buffer for RC ACKs
This reduces the latency for RC ACKs when a PIO buffer is available.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:27 -07:00
Ralph Campbell
c4b4d16e09 IB/ipath: Make send buffers available for kernel if not allocated to user
A fixed partitioning of send buffers is determined at driver load time
for user processes and kernel use.  Since send buffers are a scarce
resource, it makes sense to allow the kernel to use the buffers if they
are not in use by a user process.

Also, eliminate code duplication for ipath_force_pio_avail_update().

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:26 -07:00
Michael Albaugh
4330e4dad7 IB/ipath: Prevent link-recovery code from negating admin disable
The link can be put in LINKDOWN_DISABLE state either locally or via a
MAD.  However, the link-recovery code will take it out of that state as
a side-effect of attempts to clear SerDes/XGXS issues.

We add a flag to indicate "link is down on purpose, leave it alone."

Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:26 -07:00
Ralph Campbell
8c641d4b5f IB/ipath: Remove some useless (void) casts
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:26 -07:00
Ralph Campbell
928e3e4bb9 IB/ipath: Change the module author
Update the module author to the current email address.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:26 -07:00
Robert P. J. Day
4e96a77440 RDMA/nes: Use more concise list_for_each_entry()
In list iteration code, you normally wouldn't be calling
"container_of()" directly anyway, you'd be invoking "list_entry()".
But you don't even need that here, "list_for_each_entry()" is fine.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:26 -07:00
Roland Dreier
4d43653263 RDMA/nes: Remove session_id from nes_cm stuff
The session_id members of struct nes_cm_listener and struct
nes_cm_node are write-only, so remove them.  This allows the
session_id member of struct nes_cm_core to be removed as well, since
it is only used to write those other session_id values.

This removes the use of current->tgid (which will be deprecated)
pointed out by Pavel Emelyanov <xemul@openvz.org>.

Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:25 -07:00
Roland Dreier
782203884e IB/ipath: Fix PCI config write size used to clear linkctrl error bits
In slave_or_pri_blk(), pci_write_config_byte() is used to write a
16-bit quantity to clear linkctrl CRC error bits.  This is clearly a
bug and also causes the warning

    drivers/infiniband/hw/ipath/ipath_iba6110.c: In function 'slave_or_pri_blk':
    drivers/infiniband/hw/ipath/ipath_iba6110.c:849: warning: overflow in implicit constant conversion

Fix this by using pci_write_config_word() instead.

Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:25 -07:00
Ralph Campbell
10a8c3cd01 IB/ipath: Fix sanity checks on QP number of WRs and SGEs
The receive queue number of WRs and SGEs shouldn't be checked if a
SRQ is specified.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:25 -07:00
Ralph Campbell
69bd74c696 IB/ipath: Remove useless comments
Remove useless comment about list removal since locks are held and
the code checks that the QP is on the list before removing it.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:25 -07:00
Dave Olson
72708a0a2b IB/ipath: HW workaround for case where chip can send but not receive
Workaround a QLE7140 problem that in rare cases causes flow control
problems after link recovery by forcing a link retrain after recovery.
A module parameter is provided to control the behavior in case it causes
problems.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:25 -07:00
Ralph Campbell
a51a2513a8 IB/ipath: Add code to support multiple link speeds and widths
This patch adds code to get/set portinfo to support multiple link speeds
and widths.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:24 -07:00
John Gregor
58411d1c01 IB/ipath: Head of Line blocking vs forward progress of user apps
There's a conflict between our need to quiesce PSM-based applications
to avoid HoL blocking when the IB link goes down and the apps' desire
to remain running so that their quiescence timout mechanism can keep
running.

The compromise is to STOP the processes for a fixed period of time and
then alternate between CONT and STOP until the link is again active.

If there are poor interactions with subnet manager configuration at a
given site, the interval can be adjusted via a module paramter.

Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:24 -07:00
Ralph Campbell
6be979d71a IB/ipath: Make debug error message match the constraint that is checked for
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:24 -07:00
Ralph Campbell
c1702be20f IB/ipath: Don't try to handle freeze mode HW errors if diagnostic mode
Don't try to handle freeze mode HW errors if the driver is in diagnostic
mode since some tests can cause errors that shouldn't be processed.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:14 -07:00
Arthur Jones
b848882153 IB/ipath: Fix link up LED display
The check for link up was incorrect, thus setting the LED display
inconsistently with the link state.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:13 -07:00
Ralph Campbell
8bae0ff259 IB/ipath: Fix error recovery for send buffer status after chip freeze mode
The error recovery code for updating the driver's cached status information
for which send buffers are busy or free wasn't updated for IBA7220.
It should be similar to the initialization code in enable_chip().

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:13 -07:00
Ralph Campbell
0349d16620 IB/ipath: Fix byte order of pioavail in handle_errors()
Fix byte order of value assigned to pioavailshadow.  This bug was
detected by sparse endianness warnings.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:13 -07:00
Roland Dreier
c263ff65d5 IB/mthca: Avoid integer overflow when allocating huge ICM table
In mthca_alloc_icm_table(), the number of entries to allocate for the
table->icm array is computed by calculating obj_size * nobj and then
dividing by MTHCA_TABLE_CHUNK_SIZE.  If nobj is really large, then
obj_size * nobj may overflow and the division may get the wrong value
(even a negative value).  Fix this by calculating the number of
objects per chunk and then dividing nobj by this value instead.

This patch allows crazy configurations such as loading ib_mthca with
the module parameter num_mtt=33554432 to work properly.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:13 -07:00
Roland Dreier
19773539d6 IB/mthca: Avoid integer overflow when dealing with profile size
mthca_make_profile() returns the size in bytes of the HCA context
layout it creates, or a negative value if an error occurs.  However,
the return value is declared as u64 and the memfree initialization
path casts this value to int to test if it is negative.  This makes it
think incorrectly than an error has occurred if the context size
happens to be bigger than 2GB, since this turns into a negative int.

Fix this by having mthca_make_profile() return an s64 and testing
for an error by checking whether this 64-bit value itself is negative.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:13 -07:00
Hoang-Nam Nguyen
f4f82994d1 IB/ehca: Remove tgid checking
Pavel Emelyanov <xemul@openvz.org> mentioned in <http://lkml.org/lkml/2008/3/17/131>
that the task_struct->tgid field is about to become deprecated, so the
uses in the ehca driver need to be fixed up.

However, all the uses in ehca are for some object ownership checking
that is not really needed, and anyway is implementing a policy that
should be in common code rather than a low-level driver.  So just
remove all the checks.

Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:13 -07:00
Dave Olson
826d801009 IB/ipath: Enable 4KB MTU
Enable use of 4KB MTU.  Since the driver uses more pinned memory for
receive buffers when the 4KB MTU is enabled, whether or not the fabric
supports that MTU, add a "mtu4096" module parameter that can be used to
limit the MTU to 2KB when it is known that 4KB MTUs can't be used
anyway.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:12 -07:00
Dave Olson
5d1ce03dd3 IB/ipath: Shared context code needs to be sure device is usable
The code was checking if units are present, but not that present units
were usable (link up, etc.)

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:12 -07:00
Arthur Jones
6ca2abf4c0 IB/ipath: Provide I/O bus speeds for diagnostic purposes
Modern I/O buses like PCIe and HT can be configured for multiple speeds
and widths.  When an ipath HCA seems to have lower than expected
performance, it is very useful to be able to display what the driver
thinks the bus speed is.

Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:12 -07:00
Dave Olson
f2ceb4929a IB/ipath: Make some constants chip-specific, related cleanup
This patch makes some constants chip-specific, and makes some related
changes to prepare for supporting another HCA.

Signed-off-by: Dave Olson <dave.olson@qlogic.com
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:12 -07:00
Arthur Jones
3dd59e226e IB/ipath: Misc sparse warning cleanup
Recent sparse versions and kernel cleanups knock down the false positive
rate of the ipath driver code to a point where having it be sparse clean
is worthwhile. Here we fixup the sparse warnings.  Some of these warnings
(and the impetus to run sparse again) are due to work by Roland Dreier.

Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:11 -07:00
Eli Cohen
680b575f6d IB/mthca: Add IPoIB checksum offload support
Arbel and Sinai devices support checksum generation and verification
of TCP and UDP packets for UD IPoIB messages.  This patch checks if
the HCA supports this and sets the IB_DEVICE_UD_IP_CSUM capability
flag if it does.  It implements support for handling the IB_SEND_IP_CSUM
send flag and setting the csum_ok field in receive work completions.

Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:11 -07:00
Eli Cohen
8ff095ec4b IB/mlx4: Add IPoIB checksum offload support
ConnectX devices support checksum generation and verification of TCP
and UDP packets for UD IPoIB messages.  This patch checks if the HCA
supports this and sets the IB_DEVICE_UD_IP_CSUM capability flag if it
does.  It implements support for handling the IB_SEND_IP_CSUM send
flag and setting the csum_ok field in receive work completions.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Ali Ayub <ali@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:10 -07:00
Harvey Harrison
3371836383 IB: Replace remaining __FUNCTION__ occurrences with __func__
__FUNCTION__ is gcc-specific, use __func__ instead.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:10 -07:00
Roland Dreier
e8e91f6b4d IB/ehca: Make symbols used only in a single source file static
Allow the compiler to optimize better and generate smaller code:

add/remove: 0/6 grow/shrink: 2/0 up/down: 1528/-1864 (-336)
function                                     old     new   delta
.ehca_set_pagebuf                           1344    2172    +828
.ehca_probe                                 2312    3012    +700
ehca_set_pagebuf_phys                         24       -     -24
ehca_set_pagebuf_fmr                          24       -     -24
ehca_init_device                              24       -     -24
.ehca_set_pagebuf_fmr                        480       -    -480
.ehca_set_pagebuf_phys                       512       -    -512
.ehca_init_device                            800       -    -800

Also this fixes warnings like:

    drivers/infiniband/hw/ehca/ehca_mrmw.c:2015:5: warning: symbol 'ehca_set_pagebuf_fmr' was not declared. Should it be static?

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:10 -07:00
Roland Dreier
1a855fbfb6 RDMA/nes: Make symbols used only in a single source file static
Avoid namespace pollution and allow the compiler to optimize better.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:09 -07:00
Roland Dreier
71e0957c62 RDMA/nes: Use proper format and cast to print dma_addr_t
On some platforms, eg sparc64, dma_addr_t is not the same size as a
pointer, so printing dma_addr_t values by casting to void * and using
a %p format generates warnings.  Fix this by casting to unsigned long
and using %lx instead.  This fixes the warnings:

    drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_setup_virt_qp':
    drivers/infiniband/hw/nes/nes_verbs.c:1047: warning: cast to pointer from integer of different size
    drivers/infiniband/hw/nes/nes_verbs.c:1078: warning: cast to pointer from integer of different size
    drivers/infiniband/hw/nes/nes_verbs.c:1078: warning: cast to pointer from integer of different size
    drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_reg_user_mr':
    drivers/infiniband/hw/nes/nes_verbs.c:2657: warning: cast to pointer from integer of different size

Reported by Andrew Morton <akpm@linux-foundation.org>.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:09 -07:00
Roland Dreier
9d84ab9c7e RDMA/nes: Remove unused nes_netdev_exit() function
nes_netdev_exit() has no callers, so delete it.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:09 -07:00
Roland Dreier
5bd8341ce2 RDMA/nes: Remove redundant NULL check in nes_unregister_ofa_device()
nes_unregister_ofa_device() dereferences the nesibdev pointer before
testing if it's NULL.  Also, the test is doubly redundant because the
only caller of nes_unregister_ofa_device() is nes_destroy_ofa_device(),
which already tests if nesibdev is NULL.  Remove the unnecessary test.

This was spotted by the Coverity checker (CID 2190).

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:09 -07:00
Roland Dreier
37608eea86 mlx4_core: Fix confusion between mlx4_event and mlx4_dev_event enums
The struct mlx4_interface.event() method was supposed to get an enum
mlx4_dev_event, but the driver code was actually passing in the
hardware enum mlx4_event values.  Fix up the callers of
mlx4_dispatch_event() so that they pass in the right type of value,
and fix up the event method in mlx4_ib so that it can handle the enum
mlx4_dev_event values.

This eliminates the need for the subtype parameter to the event
method, so remove it.

This also fixes the sparse warning

    drivers/net/mlx4/intf.c:127:48: warning: mixing different enum types
    drivers/net/mlx4/intf.c:127:48:     int enum mlx4_event  versus
    drivers/net/mlx4/intf.c:127:48:     int enum mlx4_dev_event

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:08 -07:00
Roland Dreier
26c4fc26d0 RDMA/amso1100: Endian annotate mqsq allocator
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:08 -07:00
Roland Dreier
dc544bc9cb RDMA/amso1100: Start of endianness annotation
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
2008-04-16 21:01:08 -07:00
Roland Dreier
d23b9d8ff2 RDMA/nes: Delete unused variables
None of the cqp_reqs_XXX counters were ever used anywhere, and neither
was the nics_per_function variable.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:08 -07:00
Roland Dreier
b30db1c186 RDMA/nes: Trivial endianness annotations
Fix a couple of htonl() that should really be ntohl().

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:07 -07:00
Roland Dreier
d2ae16d576 IB/mlx4: Endianness annotations
Trivial fixes to stamp_send_wqe().

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:07 -07:00
Roland Dreier
6358ae25fd IB/ipath: Fix sparse warning about shadowed symbol
Fix

    drivers/infiniband/hw/ipath/ipath_init_chip.c:526:10: warning: symbol 'val' shadows an earlier one
    drivers/infiniband/hw/ipath/ipath_init_chip.c:473:6: originally declared here

by giving the second val a different name.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Arthur Jones <arthur.jones@qlogic.com>
2008-04-16 21:01:07 -07:00
Arthur Jones
6ef6aee2f0 IB/ipath: Fix sparse warning about pointer signedness
There's no reason for the third parameter of ipath_count_units() to be
a u32 *, so change it to be an int * instead.  This fixes the sparse
warning:

    drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47: warning: incorrect type in argument 3 (different signedness)
    drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47:    expected unsigned int [usertype] *maxportsp
    drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47:    got int *<noident>

Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:06 -07:00
Roland Dreier
edba846af9 RDMA/cxgb3: IDR IDs are signed
Fix sparse warnings about pointer signedness by using a signed int when
calling idr_get_new_above().

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
2008-04-16 21:01:06 -07:00
Roland Dreier
4b29043921 RDMA/amso1100: Don't use 0UL as a NULL pointer
Write tests for NULL pointers as

	if (!ptr)

instead of

	if (ptr == 0UL)

to fix sparse warnings.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
2008-04-16 21:01:06 -07:00
Roland Dreier
5d5e815db9 IB/mlx4: Convert "if(foo)" to "if (foo)"
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:04 -07:00
Roland Dreier
b39993936d IB/mthca: Formatting cleanups
Fix a few whitespace and other coding style problems.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:03 -07:00