Handle the misconfiguration where CONFIG_PHYSICAL_START is
incompatible with CONFIG_PHYSICAL_ALIGN. This is a configuration
error, but one which arises easily since Kconfig doesn't have the
smarts to express the true relationship between these two variables.
Hence, align __PHYSICAL_START the same way we align LOAD_PHYSICAL_ADDR
in <asm/boot.h>.
For non-relocatable kernels, this would cause the boot to fail.
[ Impact: fix boot failures for non-relocatable kernels ]
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Ed found that on 32-bit, boot_cpu_physical_apicid is not read right,
when the mptable is broken.
Interestingly, actually three paths use/set it:
1. acpi: at that time that is already read from reg
2. mptable: only read from mptable
3. no madt, and no mptable, that use default apic id 0 for 64-bit, -1 for 32-bit
so we could read the apic id for the 2/3 path. We trust the hardware
register more than we trust a BIOS data structure (the mptable).
We can also avoid the double set_fixmap() when acpi_lapic
is used, and also need to move cpu_has_apic earlier and
call apic_disable().
Also when need to update the apic id, we'd better read and
set the apic version as well - so that quirks are applied precisely.
v2: make path 3 with 64bit, use -1 as apic id, so could read it later.
v3: fix whitespace problem pointed out by Ed Swierk
v5: fix boot crash
[ Impact: get correct apic id for bsp other than acpi path ]
Reported-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <49FC85A9.2070702@kernel.org>
[ v4: sanity-check in the ACPI case too ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: both topics modify the APIC code but were able to do it in
parallel so far. An upcoming patch generates a conflict so
merge them to avoid the conflict.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Solve issues described in 6f66cbc630
in a way that doesn't resort to set_cpus_allowed();
* in fact, only collect_cpu_info and apply_microcode callbacks
must run on a target cpu, others will do just fine on any other.
smp_call_function_single() (as suggested by Ingo) is used to run
these callbacks on a target cpu.
* cleanup of synchronization logic of the 'microcode_core' part
The generic 'microcode_core' part guarantees that only a single cpu
(be it a full-fledged cpu, one of the cores or HT)
is being updated at any particular moment of time.
In general, there is no need for any additional sync. mechanism in
arch-specific parts (the patch removes existing spinlocks).
See also the "Synchronization" section in microcode_core.c.
* return -EINVAL instead of -1 (which is translated into -EPERM) in
microcode_write(), reload_cpu() and mc_sysdev_add(). Other suggestions
for an error code?
* use 'enum ucode_state' as return value of request_microcode_{fw, user}
to gain more flexibility by distinguishing between real error cases
and situations when an appropriate ucode was not found (which is not an
error per-se).
* some minor cleanups
Thanks a lot to Hugh Dickins for review/suggestions/testing!
Reference: http://marc.info/?l=linux-kernel&m=124025889012541&w=2
[ Impact: refactor and clean up microcode driver locking code ]
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Peter Oruba <peter.oruba@amd.com>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <1242078507.5560.9.camel@earth>
[ did some more cleanups ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/include/asm/microcode.h | 25 ++
arch/x86/kernel/microcode_amd.c | 58 ++----
arch/x86/kernel/microcode_core.c | 326 +++++++++++++++++++++-----------------
arch/x86/kernel/microcode_intel.c | 92 +++-------
4 files changed, 261 insertions(+), 240 deletions(-)
(~20 new comment lines)
A long ago, in days of yore, it all began with a god named Thor.
There were vikings and boats and some plans for a Linux kernel
header. Unfortunately, a single 8-bit field was used for bootloader
type and version. This has generally worked without *too* much pain,
but we're getting close to flat running out of ID fields.
Add extension fields for both type and version. The type will be
extended if it the old field is 0xE; the version is a simple MSB
extension.
Keep /proc/sys/kernel/bootloader_type containing
(type << 4) + (ver & 0xf) for backwards compatiblity, but also add
/proc/sys/kernel/bootloader_version which contains the full version
number.
[ Impact: new feature to support more bootloaders ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make the kernel_alignment field adjustable; this allows us to set it
to a large value (intended to be 16 MB to avoid ZONE_DMA contention,
memory holes and other weirdness) while a smart bootloader can still
force a loading at a lesser alignment if absolutely necessary.
Also export pref_address (preferred loading address, corresponding to
the link-time address) and init_size, the total amount of linear
memory the kernel will require during initialization.
[ Impact: allows better kernel placement, gives bootloader more info ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Use ®s->sp instead of regs for getting the top of stack in kernel mode.
(on x86-64, regs->sp always points the top of stack)
[ Impact: Oprofile decodes only stack for backtracing on i386 ]
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
[ v2: rename the API to kernel_stack_pointer(), move variable inside ]
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: systemtap@sources.redhat.com
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jan Blunck <jblunck@suse.de>
Cc: Christoph Hellwig <hch@infradead.org>
LKML-Reference: <20090511210300.17332.67549.stgit@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix to prevent sched_mc_power_saving from being exported through sysfs
for multi-scoket single core system. Max cores should be always greater than
one (1). My earlier patch that introduced fix for not exporting
'sched_mc_power_saving' on laptops broke it on multi-socket single core
system. This fix addresses issue on both laptop and multi-socket single
core system.
Below are the Test results:
1. Single socket - multi-core
Before Patch: Does not export 'sched_mc_power_saving'
After Patch: Does not export 'sched_mc_power_saving'
Result: Pass
2. Multi Socket - single core
Before Patch: exports 'sched_mc_power_saving'
After Patch: Does not export 'sched_mc_power_saving'
Result: Pass
3. Multi Socket - Multi core
Before Patch: exports 'sched_mc_power_saving'
After Patch: exports 'sched_mc_power_saving'
[ Impact: make the sched_mc_power_saving control available more consistently ]
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: Suresh B Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090511143914.GB4853@dirshya.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- the byte operand constraints were wrong for 32-bit
- the to-op's input operands weren't properly parenthesized
[ Impact: fix possible miscompilation or build failure ]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
struct thread_struct::ip isn't used on x86_64, struct pt_regs::ip is used
instead.
kgdb should be reading 0 always, but I can't check it.
[ Impact: (potentially) reduce thread_struct size on 64-bit ]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: containers@lists.linux-foundation.org
LKML-Reference: <20090503233015.GJ16631@x200.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After commit 464d1a78fb aka
"[PATCH] i386: Convert i386 PDA code to use %fs"
%fs saved during context switch moved from thread_struct to pt_regs
and value on thread_struct became unused.
[ Impact: reduce thread_struct size on 32-bit ]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: containers@lists.linux-foundation.org
LKML-Reference: <20090503232952.GI16631@x200.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Both print_local_APIC (used when apic=debug kernel param is set) and
cpu_debug code missed support for some extended APIC registers that
I'd like to see.
This adds support to show:
- extended APIC feature register
- extended APIC control register
- extended LVT registers
[ Impact: print more debug info ]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <20090508162350.GO29045@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
setup_force_cpu_cap() only have one user (Xen guest code),
but it should not reuse cleared_cpu_cpus, otherwise it
will have problems on SMP.
Need to have a separate cpu_cpus_set array too, for forced-on
flags, beyond the forced-off flags.
Also need to setup handling before all cpus caps are combined.
[ Impact: fix the forced-set CPU feature flag logic ]
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Yinghai Lu <yinghai.lu@kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So we could set io apic routing when ACPI is not enabled.
[ Impact: prepare for new functionality ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A01C422.5070400@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To prepare those params for pcibios_irq_enable() to call setup_io_apic_routing().
[ Impact: extend function call API to prepare for new functionality ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A01C406.2040303@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The patch to call mp_config_acpi_gsi() from the ACPI IRQ registration
code never got mainline because there were open discussions about it.
This call is needed to properly update the kernel's copy of the mptable,
when the update_mptable boot parameter is needed.
Now that the dust has settled with the APIC unification, and since there
were no objections when the patch was re-submitted, try this again.
[ Impact: fix the update_mptable boot parameter ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A01C387.7090103@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Native x86-64 uses the IST mechanism to run int3 and debug traps on
an alternative stack. Xen does not do this, and so the frames were
being misinterpreted by the ptrace code. This change special-cases
these two exceptions by using Xen variants which run on the normal
kernel stack properly.
Impact: avoid crash or bad data when IST trap is invoked under Xen
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
MSRC001_0015 Hardware Configuration Register (HWCR) is already defined
as MSR_K7_HWCR.
And HWCR is available for >= K7.
So MSR_K8_HWCR is not required and no-one is using it.
[ Impact: cleanup, no object code change ]
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Conflicts:
arch/frv/include/asm/pgtable.h
arch/x86/include/asm/required-features.h
arch/x86/xen/mmu.c
Merge reason: x86/xen was on a .29 base still, move it to a fresher
branch and pick up Xen fixes as well, plus resolve
conflicts
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: this topic is ready for upstream now. It passed
Oleg's review and Andrew had no further mm/*
objections/observations either.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: tracing/core was on a .30-rc1 base and was missing out on
on a handful of tracing fixes present in .30-rc5-almost.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Extend the maximum addressable memory on x86-64 from 2^44 to
2^46 bytes. This requires some shuffling around of the vmalloc
and virtual memmap memory areas, to keep them away from the
direct mapping of up to 64TB of physical memory.
This patch also introduces a guard hole between the vmalloc
area and the virtual memory map space. There's really no
good reason why we wouldn't have a guard hole there.
[ Impact: future hardware enablement ]
Signed-off-by: Rik van Riel <riel@redhat.com>
LKML-Reference: <20090505172856.6820db22@cuia.bos.redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86, mce: fix boot logging logic
x86, mce: make polling timer interval per CPU
Conflicts:
arch/x86/kernel/apic/io_apic.c
Merge reason: non-trivial interaction between ongoing work in io_apic.c
and the NUMA migration feature in the irq tree.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is necessary to avoid the conflict of syscall numbers.
Conflicts:
arch/x86/ia32/ia32entry.S
arch/x86/include/asm/unistd_32.h
arch/x86/include/asm/unistd_64.h
Fixes up the borked syscall numbers of perfcounters versus
preadv/pwritev as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Alternative header duplicates assembly that could be merged in
one single macro. Merging this into this macro also allows to
directly declare ALTERNATIVE() statements within assembly code.
Uses a __stringify() of the feature bits rather than passing a
"i" operand. Leave the old %0 operand as-is (set to 0), unused
to stay compatible with API.
(v2: tab alignment fixes)
[ Impact: cleanup ]
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
LKML-Reference: <20090428151346.GA31212@Krystal>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We want to use dev_to_node() later on, to be aware of the 'home node'
of the GSI in question.
[ Impact: cleanup, prepare the IRQ code to be more NUMA aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Len Brown <lenb@kernel.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
LKML-Reference: <49F65560.20904@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
arch/x86/kernel/ptrace.c
Merge reason: fix the conflict above, and also pick up the CONFIG_BROKEN
dependency change from upstream so that we can remove it
here.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
currently these are paravirtulaized, doesn't appear any callers rely on
this (no pv_ops backends are using native_tlb and overriding cr3/4
access).
[ Impact: fix lockdep warning with paravirt and function tracer ]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
LKML-Reference: <20090423172138.GR3036@sequoia.sous-sol.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Rename set_pci_bus_resources_arch_default to x86_pci_root_bus_res_quirks, move
the weak version from common.c to i386.c, and before calling, make sure it's a
root bus.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The earlier patch to change the poller to a separate function subtly
broke the boot logging logic. This could lead to machine checks
getting logged at boot even when disabled or defaulting to off
on some systems. Fix that.
[ Impact: bug fix - avoid spurious MCE in log ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
When interrupt-remapping is enabled, we are relying on
setup_IO_APIC_irqs() to configure remapped entries in the
IO-APIC, which comes little bit later after enabling
interrupt-remapping.
Meanwhile, restoration of old io-apic entries after enabling
interrupt-remapping will not make the interrupts through
io-apic functional anyway.
So remove the unnecessary reinit_intr_remapped_IO_APIC() step.
The longer story:
When interrupt-remapping is enabled, IO-APIC entries need to be
setup in the re-mappable format (pointing to
interrupt-remapping table entries setup by the OS). This
remapping configuration is happening in the same place where we
traditionally configure IO-APIC (i.e., in
setup_IO_APIC_irqs()).
So when we enable interrupt-remapping successfully, there is no
need to restore old io-apic RTE entries before we actually do a
complete configuration shortly in setup_IO_APIC_irqs(). Old
IO-APIC RTE's may be in traditional format (non re-mappable) or
in re-mappable format pointing to interrupt-remapping table
entries setup by BIOS. Restoring both of these will not make
IO-APIC functional. We have to rely on setup_IO_APIC_irqs() for
proper configuration by OS.
So I am removing this unnecessary and broken step.
[ Impact: remove unnecessary/broken IO-APIC setup step ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Weidong Han <weidong.han@intel.com>
Cc: dwmw2@infradead.org
LKML-Reference: <20090420200450.552359000@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In non-SMP mode, the variable section attribute specified by DECLARE_PER_CPU()
does not agree with that specified by DEFINE_PER_CPU(). This means that
architectures that have a small data section references relative to a base
register may throw up linkage errors due to too great a displacement between
where the base register points and the per-CPU variable.
On FRV, the .h declaration says that the variable is in the .sdata section, but
the .c definition says it's actually in the .data section. The linker throws
up the following errors:
kernel/built-in.o: In function `release_task':
kernel/exit.c:78: relocation truncated to fit: R_FRV_GPREL12 against symbol `per_cpu__process_counts' defined in .data section in kernel/built-in.o
kernel/exit.c:78: relocation truncated to fit: R_FRV_GPREL12 against symbol `per_cpu__process_counts' defined in .data section in kernel/built-in.o
To fix this, DECLARE_PER_CPU() should simply apply the same section attribute
as does DEFINE_PER_CPU(). However, this is made slightly more complex by
virtue of the fact that there are several variants on DEFINE, so these need to
be matched by variants on DECLARE.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes guest crash 'lguest: bad read address 0x4800000 len 256'
The new per-cpu allocator ends up handing a non-linear address to
write_gdt_entry. We do __pa() on it, and hand it to the host, which
kills us.
I've long wanted to make the hypercall "LOAD_GDT_ENTRY" to match the IDT
code, but had no pressing reason until now.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: lguest@ozlabs.org
Currently, when x2apic is not enabled, interrupt remapping
will be enabled in init_dmars(), where it is too late to remap
ioapic interrupts, that is, ioapic interrupts are really in
compatibility mode, not remappable mode.
This patch always enables interrupt remapping before ioapic
setup, it guarantees all interrupts will be remapped when
interrupt remapping is enabled. Thus it doesn't need to set
the compatibility interrupt bit.
[ Impact: refactor intr-remap init sequence, enable fuller remap mode ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: allen.m.kay@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1239957736-6161-4-git-send-email-weidong.han@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Shouldn't call ack_apic_edge() in ir_ack_apic_edge(), because
ack_apic_edge() does more than just ack: it also does irq migration
in the non-interrupt-remapping case. But there is no such need for
interrupt-remapping case, as irq migration is done in the process
context.
Similarly, ir_ack_apic_level() shouldn't call ack_apic_level, and
instead should do the local cpu's EOI + directed EOI to the io-apic.
ack_x2APIC_irq() is not neccessary, because ack_APIC_irq() will use MSR
write for x2apic, and uncached write for non-x2apic.
[ Impact: simplify/standardize intr-remap IRQ acking, fix on !x2apic ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: allen.m.kay@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1239957736-6161-3-git-send-email-weidong.han@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix microcode driver newly spewing warnings
x86, PAT: Remove page granularity tracking for vm_insert_pfn maps
x86: disable X86_PTRACE_BTS for now
x86, documentation: kernel-parameters replace X86-32,X86-64 with X86
x86: pci-swiotlb.c swiotlb_dma_ops should be static
x86, PAT: Remove duplicate memtype reserve in devmem mmap
x86, PAT: Consolidate code in pat_x_mtrr_type() and reserve_memtype()
x86, PAT: Changing memtype to WC ensuring no WB alias
x86, PAT: Handle faults cleanly in set_memory_ APIs
x86, PAT: Change order of cpa and free in set_memory_wb
x86, CPA: Change idmap attribute before ioremap attribute setup
* 'x86/uv' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: UV BAU distribution and payload MMRs
x86: UV: BAU partition-relative distribution map
x86, uv: add Kconfig dependency on NUMA for UV systems
x86: prevent /sys/firmware/sgi_uv from being created on non-uv systems
x86, UV: Fix for nodes with memory and no cpus
x86, UV: system table in bios accessed after unmap
x86: UV BAU messaging timeouts
x86: UV BAU and nodes with no memory
Converting node_to_k8_nb_misc() from a macro to an inline function
makes compiler see the 'node' parameter in the !CONFIG_K8_NB too,
which eliminates these compiler warnings:
arch/x86/kernel/cpu/intel_cacheinfo.c: In function ‘show_cache_disable’:
arch/x86/kernel/cpu/intel_cacheinfo.c:712: warning: unused variable ‘node’
arch/x86/kernel/cpu/intel_cacheinfo.c: In function ‘store_cache_disable’:
arch/x86/kernel/cpu/intel_cacheinfo.c:739: warning: unused variable ‘node’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Mark Langsdorf <mark.langsdorf@amd.com>
LKML-Reference: <1239730477.2966.26.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: unification of declarations, cleanup
Unification of declarations:
moved init_memory_mapping, initmem_init and free_initmem from
page_XX_types.h to page_types.h
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1239693869.3033.31.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-rc1/xen/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: add FIX_TEXT_POKE to fixmap
xen: honour VCPU availability on boot
xen: clean up gate trap/interrupt constants
xen: set _PAGE_NX in __supported_pte_mask before pagetable construction
xen: resume interrupts before system devices.
xen/mmu: weaken flush_tlb_other test
xen/mmu: some early pagetable cleanups
Xen: Add virt_to_pfn helper function
x86-64: remove PGE from must-have feature list
xen: mask XSAVE from cpuid
NULL noise: arch/x86/xen/smp.c
xen: remove xen_load_gdt debug
xen: make xen_load_gdt simpler
xen: clean up xen_load_gdt
xen: split construction of p2m mfn tables from registration
xen: separate p2m allocation from setting
xen: disable preempt for leave_lazy_mmu
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: add linux kernel support for YMM state
x86: fix wrong section of pat_disable & make it static
x86: Fix section mismatches in mpparse
x86: fix set_fixmap to use phys_addr_t
x86: Document get_user_pages_fast()
x86, intr-remap: fix eoi for interrupt remapping without x2apic
Impact: refactor, speed up and robustize code
In case if apic was disabled by kernel option
or by hardware limits we can use dummy operations
in apic->write to simplify the ack_APIC_irq() code.
At the lame time the patch fixes the missed EOI in
do_IRQ function (which has place if kernel is compiled
as X86-32 and interrupt without handler happens where
apic was not asked to be disabled via kernel option).
Note that native_apic_write_dummy() consists of
WARN_ON_ONCE to catch any buggy writes on enabled
APICs. Could be removed after some time of testing.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <20090412165058.724788431@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, no code changed
- syscalls.h update declarations due to unifications
- irq.c declare smp_generic_interrupt() before it gets used
- process.c declare sys_fork() and sys_vfork() before they get used
- tsc.c rename tsc_khz shadowed variable
- apic/probe_32.c declare apic_default before it gets used
- apic/nmi.c prev_nmi_count should be unsigned
- apic/io_apic.c declare smp_irq_move_cleanup_interrupt() before it gets used
- mm/init.c declare direct_gbpages and free_initrd_mem before they get used
Signed-off-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: save/restore Intel-AVX state properly between tasks
Intel Advanced Vector Extensions (AVX) introduce 256-bit vector processing
capability. More about AVX at http://software.intel.com/sites/avx
Add OS support for YMM state management using xsave/xrstor infrastructure
to support AVX.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1239402084.27006.8057.camel@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix kprobes crash on 32-bit with RAM above 4G
Use phys_addr_t for receiving a physical address argument
instead of unsigned long. This allows fixmap to handle
pages higher than 4GB on x86-32.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: systemtap-ml <systemtap@sources.redhat.com>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <49DE3695.6040800@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
We can remove some #ifdefs if we define IA32_SYSCALL_VECTOR on 32-bit.
Reviewed-by Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
In preparation for unifying irqinit_{32,64}.c, make
x86_quirk_pre_intr_init() local to irqinit_32.c.
Reviewed-by Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
/dev/mem mmap code was doing memtype reserve/free for a while now.
Recently we added memtype tracking in remap_pfn_range, and /dev/mem mmap
uses it indirectly. So, we don't need seperate tracking in /dev/mem code
any more. That means another ~100 lines of code removed :-).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <20090409212709.085210000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use phys_addr_t for receiving a physical address argument instead of
unsigned long. This allows fixmap to handle pages higher than 4GB on
x86-32.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: cpu_debug remove execute permission
x86: smarten /proc/interrupts output for new counters
x86: DMI match for the Dell DXP061 as it needs BIOS reboot
x86: make 64 bit to use default_inquire_remote_apic
x86, setup: un-resequence mode setting for VGA 80x34 and 80x60 modes
x86, intel-iommu: fix X2APIC && !ACPI build failure
It seems by mistake these files got execute permissions so removing it.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
LKML-Reference: <1239211186.9037.2.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
PGE may not be available when running paravirtualized, so test the cpuid
bit before using it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Impact: cleanup
The comments which fxrstor_checking and fxsave_uset refer to is
now in fxsave. Change the comments appropriately.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
LKML-Reference: <1239190320-23952-3-git-send-email-jirislaby@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
On x86_32, separate f*rstor to an inline function which makes
restore_fpu_checking the same on both platforms -> move it
outside the ifdefs.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
LKML-Reference: <1239190320-23952-2-git-send-email-jirislaby@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, prepare FPU code unificaton
Like on x86_64, return an error from restore_fpu and kill the task
if it fails.
Also rename restore_fpu to restore_fpu_checking which allows ifdefs
to be removed in math_state_restore().
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
LKML-Reference: <1239190320-23952-1-git-send-email-jirislaby@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
arch/powerpc/include/asm/systbl.h
arch/powerpc/include/asm/unistd.h
include/linux/init_task.h
Merge reason: the conflicts are non-trivial: PowerPC placement
of sys_perf_counter_open has to be mixed with the
new preadv/pwrite syscalls.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add support for Always Running APIC timer, CPUID_0x6_EAX_Bit2.
This bit means the APIC timer continues to run even when CPU is
in deep C-states.
The advantage is that we can use LAPIC timer on these CPUs
always, and there is no need for "slow to read and program"
external timers (HPET/PIT) and the timer broadcast logic
and related code in C-state entry and exit.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* commit 'origin/master': (4825 commits)
Fix build errors due to CONFIG_BRANCH_TRACER=y
parport: Use the PCI IRQ if offered
tty: jsm cleanups
Adjust path to gpio headers
KGDB_SERIAL_CONSOLE check for module
Change KCONFIG name
tty: Blackin CTS/RTS
Change hardware flow control from poll to interrupt driven
Add support for the MAX3100 SPI UART.
lanana: assign a device name and numbering for MAX3100
serqt: initial clean up pass for tty side
tty: Use the generic RS485 ioctl on CRIS
tty: Correct inline types for tty_driver_kref_get()
splice: fix deadlock in splicing to file
nilfs2: support nanosecond timestamp
nilfs2: introduce secondary super block
nilfs2: simplify handling of active state of segments
nilfs2: mark minor flag for checkpoint created by internal operation
nilfs2: clean up sketch file
nilfs2: super block operations fix endian bug
...
Conflicts:
arch/x86/include/asm/thread_info.h
arch/x86/lguest/boot.c
drivers/xen/manage.c
Replace all DMA_24BIT_MASK macro with DMA_BIT_MASK(24)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add debug store support for Core i7.
Core i7 adds a reset value for each performance counter and a new
PEBS record format.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144607.088997000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add the ptrace bts context field to task_struct unconditionally.
Initialize the field directly in copy_process().
Remove all the unneeded functionality used to initialize that field.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144603.292754000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a warning in case a debug store context is not removed before
the task it is attached to is freed.
Remove the old warning at thread exit. It is too early.
Declare the debug store context field in thread_struct unconditionally.
Remove ds_copy_thread() and ds_exit_thread() and do the work directly
in process*.c.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144601.254472000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The hw-branch-tracer uses debug store functions from an on_each_cpu()
context, which is simply wrong since the functions may sleep.
Add _noirq variants for most functions, which may be called with
interrupts disabled.
Separate per-cpu and per-task tracing and allow per-cpu tracing to be
controlled from any cpu.
Make the hw-branch-tracer use the new debug store interface, synchronize
with hotplug cpu event using get/put_online_cpus(), and remove the
unnecessary spinlock.
Make the ptrace bts and the ds selftest code use the new interface.
Defer the ds selftest.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144555.658136000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When a ptraced task is unlinked, we need to stop branch tracing for
that task.
Since the unlink is called with interrupts disabled, and we need
interrupts enabled to stop branch tracing, we defer the work.
Collect all branch tracing related stuff in a branch tracing context.
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144550.712401000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Complete atomic64_t support on the 32-bit side by adding atomic64_xch().
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090406094518.445450972@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Implement set_perf_counter_pending() with a self-IPI so that it will
run ASAP in a usable context.
For now use a second IRQ vector, because the primary vector pokes
the apic in funny ways that seem to confuse things.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090406094517.724626696@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While going over the wakeup code I noticed delayed wakeups only work
for hardware counters but basically all software counters rely on
them.
This patch unifies and generalizes the delayed wakeup to fix this
issue.
Since we're dealing with NMI context bits here, use a cmpxchg() based
single link list implementation to track counters that have pending
wakeups.
[ This should really be generic code for delayed wakeups, but since we
cannot use cmpxchg()/xchg() in generic code, I've let it live in the
perf_counter code. -- Eric Dumazet could use it to aggregate the
network wakeups. ]
Furthermore, the x86 method of using TIF flags was flawed in that its
quite possible to end up setting the bit on the idle task, loosing the
wakeup.
The powerpc method uses per-cpu storage and does appear to be
sufficient.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Orig-LKML-Reference: <20090330171023.153932974@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix for powerpc
Commit bd753921015e7905 ("perf_counter: software counter event
infrastructure") introduced a use of TIF_PERF_COUNTERS into the core
perfcounter code. This breaks the build on powerpc because we use
a flag in a per-cpu area to signal wakeups on powerpc rather than
a thread_info flag, because the thread_info flags have to be
manipulated with atomic operations and are thus slower than per-cpu
flags.
This fixes the by changing the core to use an abstracted
set_perf_counter_pending() function, which is defined on x86 to set
the TIF_PERF_COUNTERS flag and on powerpc to set the per-cpu flag
(paca->perf_counter_pending). It changes the previous powerpc
definition of set_perf_counter_pending to not take an argument and
adds a clear_perf_counter_pending, so as to simplify the definition
on x86.
On x86, set_perf_counter_pending() is defined as a macro. Defining
it as a static inline in arch/x86/include/asm/perf_counters.h causes
compile failures because <asm/perf_counters.h> gets included early in
<linux/sched.h>, and the definitions of set_tsk_thread_flag etc. are
therefore not available in <asm/perf_counters.h>. (On powerpc this
problem is avoided by defining set_perf_counter_pending etc. in
<asm/hw_irq.h>.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge reason: we have gathered quite a few conflicts, need to merge upstream
Conflicts:
arch/powerpc/kernel/Makefile
arch/x86/ia32/ia32entry.S
arch/x86/include/asm/hardirq.h
arch/x86/include/asm/unistd_32.h
arch/x86/include/asm/unistd_64.h
arch/x86/kernel/cpu/common.c
arch/x86/kernel/irq.c
arch/x86/kernel/syscall_table_32.S
arch/x86/mm/iomap_32.c
include/linux/sched.h
kernel/Makefile
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
tracing, net: fix net tree and tracing tree merge interaction
tracing, powerpc: fix powerpc tree and tracing tree interaction
ring-buffer: do not remove reader page from list on ring buffer free
function-graph: allow unregistering twice
trace: make argument 'mem' of trace_seq_putmem() const
tracing: add missing 'extern' keywords to trace_output.h
tracing: provide trace_seq_reserve()
blktrace: print out BLK_TN_MESSAGE properly
blktrace: extract duplidate code
blktrace: fix memory leak when freeing struct blk_io_trace
blktrace: fix blk_probes_ref chaos
blktrace: make classic output more classic
blktrace: fix off-by-one bug
blktrace: fix the original blktrace
blktrace: fix a race when creating blk_tree_root in debugfs
blktrace: fix timestamp in binary output
tracing, Text Edit Lock: cleanup
tracing: filter fix for TRACE_EVENT_FORMAT events
ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
x86: kretprobe-booster interrupt emulation code fix
...
Fix up trivial conflicts in
arch/parisc/include/asm/ftrace.h
include/linux/memory.h
kernel/extable.c
kernel/module.c
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-cpumask: (36 commits)
cpumask: remove cpumask allocation from idle_balance, fix
numa, cpumask: move numa_node_id default implementation to topology.h, fix
cpumask: remove cpumask allocation from idle_balance
x86: cpumask: x86 mmio-mod.c use cpumask_var_t for downed_cpus
x86: cpumask: update 32-bit APM not to mug current->cpus_allowed
x86: microcode: cleanup
x86: cpumask: use work_on_cpu in arch/x86/kernel/microcode_core.c
cpumask: fix CONFIG_CPUMASK_OFFSTACK=y cpu hotunplug crash
numa, cpumask: move numa_node_id default implementation to topology.h
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
cpumask: remove x86 cpumask_t uses.
cpumask: use cpumask_var_t in uv_flush_tlb_others.
cpumask: remove cpumask_t assignment from vector_allocation_domain()
cpumask: make Xen use the new operators.
cpumask: clean up summit's send_IPI functions
cpumask: use new cpumask functions throughout x86
x86: unify cpu_callin_mask/cpu_callout_mask/cpu_initialized_mask/cpu_sibling_setup_mask
cpumask: convert struct cpuinfo_x86's llc_shared_map to cpumask_var_t
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
x86: unify 32 and 64-bit node_to_cpumask_map
...
interrupt remapping must be enabled before enabling x2apic, but
interrupt remapping doesn't depend on x2apic, it can be used
separately. Enable interrupt remapping in init_dmars even x2apic
is not supported.
[dwmw2: Update Kconfig accordingly, fix build with INTR_REMAP && !X2APIC]
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch enables suspend/resume for interrupt remapping. During suspend,
interrupt remapping is disabled. When resume, interrupt remapping is enabled
again.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch replaces a 'nop' uv_enable_timeouts() in the
UV TLB shootdown code. (somehow, long ago that function got
eviscerated)
If any cpu in the destination node does not get interrupted by the
message and post completion in a reasonable time the hardware
should respond to the sender with an error. This function
enables such timeouts.
Tested on the UV hardware simulator.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <E1LpjXU-00007e-Qh@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: unification of pci-dma macros and pci_32.h removal
This patch unifies the definition of the pci_unmap_addr*, pci_unmap_len*
and DECLARE_PCI_UNMAP* macros. This makes sense because the pci_unmap
functions are no longer no-ops anymore when the kernel runs with
CONFIG_DMA_API_DEBUG. Without an iommu or DMA_API_DEBUG it is a no-op on 32 bit
because the dma mapping path returns a physical address and therefore the
dma-api implementation has no internal state which needs to be destroyed with
an unmap call.
This unification also simplifies the port of x86_64 iommu drivers to 32 bit x86
and let us get rid of pci_32.h.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Pass the original flags to rwlock arch-code, so that it can re-enable
interrupts if implemented for that architecture.
Initially, make __raw_read_lock_flags and __raw_write_lock_flags stubs
which just do the same thing as non-flags variants.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds preadv and pwritev system calls. These syscalls are a
pretty straightforward combination of pread and readv (same for write).
They are quite useful for doing vectored I/O in threaded applications.
Using lseek+readv instead opens race windows you'll have to plug with
locking.
Other systems have such system calls too, for example NetBSD, check
here: http://www.daemon-systems.org/man/preadv.2.html
The application-visible interface provided by glibc should look like
this to be compatible to the existing implementations in the *BSD family:
ssize_t preadv(int d, const struct iovec *iov, int iovcnt, off_t offset);
ssize_t pwritev(int d, const struct iovec *iov, int iovcnt, off_t offset);
This prototype has one problem though: On 32bit archs is the (64bit)
offset argument unaligned, which the syscall ABI of several archs doesn't
allow to do. At least s390 needs a wrapper in glibc to handle this. As
we'll need a wrappers in glibc anyway I've decided to push problem to
glibc entriely and use a syscall prototype which works without
arch-specific wrappers inside the kernel: The offset argument is
explicitly splitted into two 32bit values.
The patch sports the actual system call implementation and the windup in
the x86 system call tables. Other archs follow as separate patches.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add macros for using the UV hub to send interrupts. Change the IPI code
to use these macros. These macros will also be used in additional patches
that will follow.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eliminate compile errors on 32-bit X86 caused by UV.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
PCI: fix HT MSI mapping fix
PCI: don't enable too much HT MSI mapping
x86/PCI: make pci=lastbus=255 work when acpi is on
PCI: save and restore PCIe 2.0 registers
PCI: update fakephp for bus_id removal
PCI: fix kernel oops on bridge removal
PCI: fix conflict between SR-IOV and config space sizing
powerpc/PCI: include pci.h in powerpc MSI implementation
PCI Hotplug: schedule fakephp for feature removal
PCI Hotplug: rename legacy_fakephp to fakephp
PCI Hotplug: restore fakephp interface with complete reimplementation
PCI: Introduce /sys/bus/pci/devices/.../rescan
PCI: Introduce /sys/bus/pci/devices/.../remove
PCI: Introduce /sys/bus/pci/rescan
PCI: Introduce pci_rescan_bus()
PCI: do not enable bridges more than once
PCI: do not initialize bridges more than once
PCI: always scan child buses
PCI: pci_scan_slot() returns newly found devices
PCI: don't scan existing devices
...
Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest-and-virtio:
lguest: barrier me harder
lguest: use bool instead of int
lguest: use KVM hypercalls
lguest: wire up pte_update/pte_update_defer
lguest: fix spurious BUG_ON() on invalid guest stack.
virtio: more neatening of virtio_ring macros.
virtio: fix BAD_RING, START_US and END_USE macros
* 'iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (60 commits)
dma-debug: make memory range checks more consistent
dma-debug: warn of unmapping an invalid dma address
dma-debug: fix dma_debug_add_bus() definition for !CONFIG_DMA_API_DEBUG
dma-debug/x86: register pci bus for dma-debug leak detection
dma-debug: add a check dma memory leaks
dma-debug: add checks for kernel text and rodata
dma-debug: print stacktrace of mapping path on unmap error
dma-debug: Documentation update
dma-debug: x86 architecture bindings
dma-debug: add function to dump dma mappings
dma-debug: add checks for sync_single_sg_*
dma-debug: add checks for sync_single_range_*
dma-debug: add checks for sync_single_*
dma-debug: add checking for [alloc|free]_coherent
dma-debug: add add checking for map/unmap_sg
dma-debug: add checking for map/unmap_page/single
dma-debug: add core checking functions
dma-debug: add debugfs interface
dma-debug: add kernel command line parameters
dma-debug: add initialization code
...
Fix trivial conflicts due to whitespace changes in arch/x86/kernel/pci-nommu.c
* 'x86-stage-3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (190 commits)
Revert "cpuacct: reduce one NULL check in fast-path"
Revert "x86: don't compile vsmp_64 for 32bit"
x86: Correct behaviour of irq affinity
x86: early_ioremap_init(), use __fix_to_virt(), because we are sure it's safe
x86: use default_cpu_mask_to_apicid for 64bit
x86: fix set_extra_move_desc calling
x86, PAT, PCI: Change vma prot in pci_mmap to reflect inherited prot
x86/dmi: fix dmi_alloc() section mismatches
x86: e820 fix various signedness issues in setup.c and e820.c
x86: apic/io_apic.c define msi_ir_chip and ir_ioapic_chip all the time
x86: irq.c keep CONFIG_X86_LOCAL_APIC interrupts together
x86: irq.c use same path for show_interrupts
x86: cpu/cpu.h cleanup
x86: Fix a couple of sparse warnings in arch/x86/kernel/apic/io_apic.c
Revert "x86: create a non-zero sized bm_pte only when needed"
x86: pci-nommu.c cleanup
x86: io_delay.c cleanup
x86: rtc.c cleanup
x86: i8253 cleanup
x86: kdebugfs.c cleanup
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (180 commits)
powerpc: clean up ssi.txt, add definition for fsl,ssi-asynchronous
powerpc/85xx: Add support for the "socrates" board (MPC8544).
powerpc: Fix bugs introduced by sysfs changes
powerpc: Sanitize stack pointer in signal handling code
powerpc: Add write barrier before enabling DTL flags
powerpc/83xx: Update ranges in gianfar node to match other dts
powerpc/86xx: Move gianfar mdio nodes under the ethernet nodes
powerpc/85xx: Move gianfar mdio nodes under the ethernet nodes
powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes
powerpc/83xx: Add power management support for MPC837x boards
powerpc/mm: Introduce early_init_mmu() on 64-bit
powerpc/mm: Add option for non-atomic PTE updates to ppc64
powerpc/mm: Fix printk type warning in mmu_context_nohash
powerpc/mm: Rename arch/powerpc/kernel/mmap.c to mmap_64.c
powerpc/mm: Merge various PTE bits and accessors definitions
powerpc/mm: Tweak PTE bit combination definitions
powerpc/cell: Fix iommu exception reporting
powerpc/mm: e300c2/c3/c4 TLB errata workaround
powerpc/mm: Used free register to save a few cycles in SW TLB miss handling
powerpc/mm: Remove unused register usage in SW TLB miss handling
...
A paravirtualized system may not have PSE or PGE available to
guests, so they are not required features. However, without
paravirt we can assume that any x86-64 implementation will have
them available.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
PGE may not be available when running paravirtualized, so test the cpuid
bit before using it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Impact: cleanup
Eliminate more than 20 unnecessary #include lines in fault.c
Also fix include file dependency bug in asm/traps.h. (this was
masked before, by implicit inclusion)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <tip-56aea8468746e673a4bf50b6a13d97b2d1cbe1e8@git.kernel.org>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Everyone defines it, and only one person uses it
(arch/mips/sgi-ip27/ip27-nmi.c). So just open code it there.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-mips@linux-mips.org
Impact: cleanup
This patch allow us to use KVM hypercalls
Signed-off-by: Matias Zabaljauregui <zabaljauregui at gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Impact: fix lazy context switch API
Pass the previous and next tasks into the context switch start
end calls, so that the called functions can properly access the
task state (esp in end_context_switch, in which the next task
is not yet completely current).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Impact: allow preemption during lazy mmu updates
If we're in lazy mmu mode when context switching, leave
lazy mmu mode, but remember the task's state in
TIF_LAZY_MMU_UPDATES. When we resume the task, check this
flag and re-enter lazy mmu mode if its set.
This sets things up for allowing lazy mmu mode while preemptible,
though that won't actually be active until the next change.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Impact: simplification, prepare for later changes
Make lazy cpu mode more specific to context switching, so that
it makes sense to do more context-switch specific things in
the callbacks.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Conflicts:
arch/sparc/kernel/time_64.c
drivers/gpu/drm/drm_proc.c
Manual merge to resolve build warning due to phys_addr_t type change
on x86:
drivers/gpu/drm/drm_info.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Due to a different size of ino_t ustat needs a compat handler, but
currently only x86 and mips provide one. Add a generic compat_sys_ustat
and switch all architectures over to it. Instead of doing various
user copy hacks compat_sys_ustat just reimplements sys_ustat as
it's trivial. This was suggested by Arnd Bergmann.
Found by Eric Sandeen when running xfstests/017 on ppc64, which causes
stack smashing warnings on RHEL/Fedora due to the too large amount of
data writen by the syscall.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1750 commits)
ixgbe: Allow Priority Flow Control settings to survive a device reset
net: core: remove unneeded include in net/core/utils.c.
e1000e: update version number
e1000e: fix close interrupt race
e1000e: fix loss of multicast packets
e1000e: commonize tx cleanup routine to match e1000 & igb
netfilter: fix nf_logger name in ebt_ulog.
netfilter: fix warning in ebt_ulog init function.
netfilter: fix warning about invalid const usage
e1000: fix close race with interrupt
e1000: cleanup clean_tx_irq routine so that it completely cleans ring
e1000: fix tx hang detect logic and address dma mapping issues
bridge: bad error handling when adding invalid ether address
bonding: select current active slave when enslaving device for mode tlb and alb
gianfar: reallocate skb when headroom is not enough for fcb
Bump release date to 25Mar2009 and version to 0.22
r6040: Fix second PHY address
qeth: fix wait_event_timeout handling
qeth: check for completion of a running recovery
qeth: unregister MAC addresses during recovery.
...
Manually fixed up conflicts in:
drivers/infiniband/hw/cxgb3/cxio_hal.h
drivers/infiniband/hw/nes/nes_nic.c
* 'kvm-updates/2.6.30' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (113 commits)
KVM: VMX: Don't allow uninhibited access to EFER on i386
KVM: Correct deassign device ioctl to IOW
KVM: ppc: e500: Fix the bug that KVM is unstable in SMP
KVM: ppc: e500: Fix the bug that mas0 update to wrong value when read TLB entry
KVM: Fix missing smp tlb flush in invlpg
KVM: Get support IRQ routing entry counts
KVM: fix sparse warnings: Should it be static?
KVM: fix sparse warnings: context imbalance
KVM: is_long_mode() should check for EFER.LMA
KVM: VMX: Update necessary state when guest enters long mode
KVM: ia64: Fix the build errors due to lack of macros related to MSI.
ia64: Move the macro definitions related to MSI to one header file.
KVM: fix kvm_vm_ioctl_deassign_device
KVM: define KVM_CAP_DEVICE_DEASSIGNMENT
KVM: ppc: Add emulation of E500 register mmucsr0
KVM: Report IRQ injection status for MSI delivered interrupts
KVM: MMU: Fix another largepage memory leak
KVM: SVM: set accessed bit for VMCB segment selectors
KVM: Report IRQ injection status to userspace.
KVM: MMU: remove assertion in kvm_mmu_alloc_page
...
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (29 commits)
crypto: sha512-s390 - Add missing block size
hwrng: timeriomem - Breaks an allyesconfig build on s390:
nlattr: Fix build error with NET off
crypto: testmgr - add zlib test
crypto: zlib - New zlib crypto module, using pcomp
crypto: testmgr - Add support for the pcomp interface
crypto: compress - Add pcomp interface
netlink: Move netlink attribute parsing support to lib
crypto: Fix dead links
hwrng: timeriomem - New driver
crypto: chainiv - Use kcrypto_wq instead of keventd_wq
crypto: cryptd - Per-CPU thread implementation based on kcrypto_wq
crypto: api - Use dedicated workqueue for crypto subsystem
crypto: testmgr - Test skciphers with no IVs
crypto: aead - Avoid infinite loop when nivaead fails selftest
crypto: skcipher - Avoid infinite loop when cipher fails selftest
crypto: api - Fix crypto_alloc_tfm/create_create_tfm return convention
crypto: api - crypto_alg_mod_lookup either tested or untested
crypto: amcc - Add crypt4xx driver
crypto: ansi_cprng - Add maintainer
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: (35 commits)
[CPUFREQ] Prevent p4-clockmod from auto-binding to the ondemand governor.
[CPUFREQ] Make cpufreq-nforce2 less obnoxious
[CPUFREQ] p4-clockmod reports wrong frequency.
[CPUFREQ] powernow-k8: Use a common exit path.
[CPUFREQ] Change link order of x86 cpufreq modules
[CPUFREQ] conservative: remove 10x from def_sampling_rate
[CPUFREQ] conservative: fixup governor to function more like ondemand logic
[CPUFREQ] conservative: fix dbs_cpufreq_notifier so freq is not locked
[CPUFREQ] conservative: amend author's email address
[CPUFREQ] Use swap() in longhaul.c
[CPUFREQ] checkpatch cleanups for acpi-cpufreq
[CPUFREQ] powernow-k8: Only print error message once, not per core.
[CPUFREQ] ondemand/conservative: sanitize sampling_rate restrictions
[CPUFREQ] ondemand/conservative: deprecate sampling_rate{min,max}
[CPUFREQ] powernow-k8: Always compile powernow-k8 driver with ACPI support
[CPUFREQ] Introduce /sys/devices/system/cpu/cpu*/cpufreq/cpuinfo_transition_latency
[CPUFREQ] checkpatch cleanups for powernow-k8
[CPUFREQ] checkpatch cleanups for ondemand governor.
[CPUFREQ] checkpatch cleanups for powernow-k7
[CPUFREQ] checkpatch cleanups for speedstep related drivers.
...
Impact: cleanup
'make headers_check' warn us about leaking of kernel private
(mostly compile time vars) data to userspace in headers. Fix it.
Guard this one by __KERNEL__.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Partial revert of commit 129d8bc828
titled 'x86: don't compile vsmp_64 for 32bit'
Commit reverted to compile vsmp_64.c if CONFIG_X86_64 is defined,
since is_vsmp_box() needs to indicate that TSCs are not synchronized, and
hence, not a valid time source, even when CONFIG_X86_VSMP is not defined.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: shai@scalex86.org
LKML-Reference: <20090324061429.GH7278@localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IRQ injection status is either -1 (if there was no CPU found
that should except the interrupt because IRQ was masked or
ioapic was misconfigured or ...) or >= 0 in that case the
number indicates to how many CPUs interrupt was injected.
If the value is 0 it means that the interrupt was coalesced
and probably should be reinjected.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
AMD k10 includes support for the FFXSR feature, which leaves out
XMM registers on FXSAVE/FXSAVE when the EFER_FFXSR bit is set in
EFER.
The CPUID feature bit exists already, but the EFER bit is missing
currently, so this patch adds it to the list of known EFER bits.
Signed-off-by: Alexander Graf <agraf@suse.de>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Kconfig symbols are not available in userspace, and are not stripped by
headers-install. Avoid their use by adding #defines in <asm/kvm.h> to
suit each architecture.
Signed-off-by: Avi Kivity <avi@redhat.com>
This actually describes what is going on, rather than alerting the reader
that something strange is going on.
Signed-off-by: Avi Kivity <avi@redhat.com>
Certain clocks (such as TSC) in older 2.6 guests overaccount for lost
ticks, causing severe time drift. Interrupt reinjection magnifies the
problem.
Provide an option to disable it.
[avi: allow room for expansion in case we want to disable reinjection
of other timers]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This commit change the name of emulator_read_std into kvm_read_guest_virt,
and add new function name kvm_write_guest_virt that allow writing into a
guest virtual address.
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
VMX initializes the TSC offset for each vcpu at different times, and
also reinitializes it for vcpus other than 0 on APIC SIPI message.
This bug causes the TSC's to appear unsynchronized in the guest, even if
the host is good.
Older Linux kernels don't handle the situation very well, so
gettimeofday is likely to go backwards in time:
http://www.mail-archive.com/kvm@vger.kernel.org/msg02955.htmlhttp://sourceforge.net/tracker/index.php?func=detail&aid=2025534&group_id=180599&atid=893831
Fix it by initializating the offset of each vcpu relative to vm creation
time, and moving it from vmx_vcpu_reset to vmx_vcpu_setup, out of the
APIC MP init path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Don't allow a vcpu with cr4.pge cleared to use a shadow page created with
cr4.pge set; this might cause a cr3 switch not to sync ptes that have the
global bit set (the global bit has no effect if !cr4.pge).
This can only occur on smp with different cr4.pge settings for different
vcpus (since a cr4 change will resync the shadow ptes), but there's no
cost to being correct here.
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of "calculating" it on every shadow page allocation, set it once
when switching modes, and copy it when allocating pages.
This doesn't buy us much, but sets up the stage for inheriting more
information related to the mmu setup.
Signed-off-by: Avi Kivity <avi@redhat.com>
So far KVM only had basic x86 debug register support, once introduced to
realize guest debugging that way. The guest itself was not able to use
those registers.
This patch now adds (almost) full support for guest self-debugging via
hardware registers. It refactors the code, moving generic parts out of
SVM (VMX was already cleaned up by the KVM_SET_GUEST_DEBUG patches), and
it ensures that the registers are properly switched between host and
guest.
This patch also prepares debug register usage by the host. The latter
will (once wired-up by the following patch) allow for hardware
breakpoints/watchpoints in guest code. If this is enabled, the guest
will only see faked debug registers without functionality, but with
content reflecting the guest's modifications.
Tested on Intel only, but SVM /should/ work as well, but who knows...
Known limitations: Trapping on tss switch won't work - most probably on
Intel.
Credits also go to Joerg Roedel - I used his once posted debugging
series as platform for this patch.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This rips out the support for KVM_DEBUG_GUEST and introduces a new IOCTL
instead: KVM_SET_GUEST_DEBUG. The IOCTL payload consists of a generic
part, controlling the "main switch" and the single-step feature. The
arch specific part adds an x86 interface for intercepting both types of
debug exceptions separately and re-injecting them when the host was not
interested. Moveover, the foundation for guest debugging via debug
registers is layed.
To signal breakpoint events properly back to userland, an arch-specific
data block is now returned along KVM_EXIT_DEBUG. For x86, the arch block
contains the PC, the debug exception, and relevant debug registers to
tell debug events properly apart.
The availability of this new interface is signaled by
KVM_CAP_SET_GUEST_DEBUG. Empty stubs for not yet supported archs are
provided.
Note that both SVM and VTX are supported, but only the latter was tested
yet. Based on the experience with all those VTX corner case, I would be
fairly surprised if SVM will work out of the box.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
VMX differentiates between processor and software generated exceptions
when injecting them into the guest. Extend vmx_queue_exception
accordingly (and refactor related constants) so that we can use this
service reliably for the new guest debugging framework.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements VMRUN. VMRUN enters a virtual CPU and runs that
in the same context as the normal guest CPU would run.
So basically it is implemented the same way, a normal CPU would do it.
We also prepare all intercepts that get OR'ed with the original
intercepts, as we do not allow a level 2 guest to be intercepted less
than the first level guest.
v2 implements the following improvements:
- fixes the CPL check
- does not allocate iopm when not used
- remembers the host's IF in the HIF bit in the hflags
v3:
- make use of the new permission checking
- add support for V_INTR_MASKING_MASK
v4:
- use host page backed hsave
v5:
- remove IOPM merging code
v6:
- save cr4 so PAE l1 guests work
v7:
- return 0 on vmrun so we check the MSRs too
- fix MSR check to use the correct variable
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the GIF flag and the clgi and stgi instructions that
set this flag. Only if the flag is set (default), interrupts can be received by
the CPU.
To keep the information about that somewhere, this patch adds a new hidden
flags vector. that is used to store information that does not go into the
vmcb, but is SVM specific.
I tried to write some code to make -no-kvm-irqchip work too, but the first
level guest won't even boot with that atm, so I ditched it.
v2 moves the hflags to x86 generic code
v3 makes use of the new permission helper
v6 only enables interrupt_window if GIF=1
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
MSR_EFER_SVME_MASK, MSR_VM_CR and MSR_VM_HSAVE_PA are set in KVM
specific headers. Linux does have nice header files to collect
EFER bits and MSR IDs, so IMHO we should put them there.
While at it, I also changed the naming scheme to match that
of the other defines.
(introduced in v6)
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Impact: section mismatch fix
Ingo reports these warnings:
> WARNING: vmlinux.o(.text+0x6a288e): Section mismatch in reference from
> the function dmi_alloc() to the function .init.text:extend_brk()
> The function dmi_alloc() references
> the function __init extend_brk().
> This is often because dmi_alloc lacks a __init annotation or the
> annotation of extend_brk is wrong.
dmi_alloc() is a static inline, and so should be immune to this
kind of error. But force it to be inlined and make it __init
anyway, just to be extra sure.
All of dmi_alloc()'s callers are already __init.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <49C6B23C.2040308@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
This fixed various signedness issues in setup.c and e820.c:
arch/x86/kernel/setup.c:455:53: warning: incorrect type in argument 3 (different signedness)
arch/x86/kernel/setup.c:455:53: expected int *pnr_map
arch/x86/kernel/setup.c:455:53: got unsigned int extern [toplevel] *<noident>
arch/x86/kernel/setup.c:639:53: warning: incorrect type in argument 3 (different signedness)
arch/x86/kernel/setup.c:639:53: expected int *pnr_map
arch/x86/kernel/setup.c:639:53: got unsigned int extern [toplevel] *<noident>
arch/x86/kernel/setup.c:820:54: warning: incorrect type in argument 3 (different signedness)
arch/x86/kernel/setup.c:820:54: expected int *pnr_map
arch/x86/kernel/setup.c:820:54: got unsigned int extern [toplevel] *<noident>
arch/x86/kernel/e820.c:670:53: warning: incorrect type in argument 3 (different signedness)
arch/x86/kernel/e820.c:670:53: expected int *pnr_map
arch/x86/kernel/e820.c:670:53: got unsigned int [toplevel] *<noident>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Add new interfaces:
set_pages_array_uc()
set_pages_array_wb()
that can be used change the page attribute for a bunch of pages with
flush etc done once at the end of all the changes. These interfaces
are similar to existing set_memory_array_uc() and set_memory_array_wc().
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: arjan@infradead.org
Cc: eric@anholt.net
Cc: airlied@redhat.com
LKML-Reference: <20090319215358.901545000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Weak functions aren't all they're cracked up to be. They lead to
incorrect binaries with some toolchains, they require us to have empty
functions we otherwise wouldn't, and the unused code is not elided
(as of gcc 4.3.2 anyway).
So replace the weak MSI arch hooks with the #define foo foo idiom. We no
longer need empty versions of arch_setup/teardown_msi_irq().
This is less source (by 1 line!), and results in smaller binaries too:
text data bss dec hex filename
9354300 1693916 678424 11726640 b2ef30 build/powerpc/vmlinux-before
9354052 1693852 678424 11726328 b2edf8 build/powerpc/vmlinux-after
Also smaller on x86_64 and arm (iop13xx).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Impact: Fix cpu offline when CONFIG_MAXSMP=y
Changeset bc9b83dd1f "cpumask: convert
c1e_mask in arch/x86/kernel/process.c to cpumask_var_t" contained a
bug: c1e_mask is manipulated even if C1E isn't detected (and hence
not allocated).
This is simply fixed by checking for NULL (which gcc optimizes out
anyway of CONFIG_CPUMASK_OFFSTACK=n, since it knows ce1_mask can never
be NULL).
In addition, fix a leak where select_idle_routine re-allocates
(and re-clears) c1e_mask on every cpu init.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Mike Travis <travis@sgi.com>
LKML-Reference: <200903171450.34549.rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: optimize APIC IPI related barriers
Uncached MMIO accesses for xapic are inherently serializing and hence
we don't need explicit barriers for xapic IPI paths.
x2apic MSR writes/reads don't have serializing semantics and hence need
a serializing instruction or mfence, to make all the previous memory
stores globally visisble before the x2apic msr write for IPI.
Add x2apic_wrmsr_fence() in flush tlb path to x2apic specific paths.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "steiner@sgi.com" <steiner@sgi.com>
Cc: Nick Piggin <npiggin@suse.de>
LKML-Reference: <1237313814.27006.203.camel@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix possible race
save_mask_IO_APIC_setup() was using non atomic memory allocation while getting
called with interrupts disabled. Fix this by splitting this into two different
function. Allocation part save_IO_APIC_setup() now happens before
disabling interrupts.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: simplification
In the current code, for level triggered migration, we need to modify the
io-apic RTE with the update vector information, along with modifying interrupt
remapping table entry(IRTE) with vector and destination. This is to ensure that
remote IRR bit inthe IOAPIC RTE gets cleared when the cpu does EOI.
With this patch, for level triggered, we eliminate the io-apic RTE modification
(with the updated vector information), by using a virtual vector (io-apic pin
number). Real vector that is used for interrupting cpu will be coming from
the interrupt-remapping table entry. Trigger mode in the IRTE will always be
edge, and the actual level or edge trigger will be setup in the IO-APIC RTE.
So a level triggered interrupt will appear as an edge to the local apic
cpu but still as level to the IO-APIC.
With this change, level irq migration can be done by simply modifying
the interrupt-remapping table entry with out changing the io-apic RTE.
And as the interrupt appears as edge at the cpu, in addition to do the
local apic EOI, we need to do IO-APIC directed EOI to clear the remote
IRR bit in the IO-APIC RTE.
This simplies the irq migration in the presence of interrupt-remapping.
Idea-by: Rajesh Sankaran <rajesh.sankaran@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: cleanup, paranoia
We were not clearing the local APIC in clear_local_APIC() in the
presence of x2apic. Fix it.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: interface augmentation (not yet used)
Enable fault handling flow for intr-remapping aswell. Fault handling
code now shared by both dma-remapping and intr-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: bulletproofing, clarification
The brk reservation symbols are just there to document the amount
of space reserved by brk users in the final vmlinux file. Their
addresses are irrelevent, and using their addresses will cause
certain havok. Name them ".brk.NAME", which is a valid asm symbol
but C can't reference it; it also highlights their special
role in the symbol table.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Impact: fix crash on VMI (VMware)
When we generate a call sequence for calling a paravirtualized
function, we presume that the generated code is "call *0xXXXXX",
which is a 6 byte opcode; this is larger than a normal
direct call, and so we can patch a direct call over it.
At the moment, however we give gcc enough rope to hang us by
putting the address in a register and generating a two byte
indirect-via-register call. Prevent this by explicitly
dereferencing the function pointer and passing it into the
asm as a constant.
This prevents crashes in VMI, as it cannot handle unpatchable
callsites.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Alok Kataria <akataria@vmware.com>
LKML-Reference: <49BEEDC2.2070809@goop.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: new interface; remove hard-coded limit
Add RESERVE_BRK(name, size) macro to reserve space in the brk
area. This should be a conservative (ie, larger) estimate of
how much space might possibly be required from the brk area.
Any unused space will be freed, so there's no real downside
on making the reservation too large (within limits).
The name should be unique within a given file, and somewhat
descriptive.
The C definition of RESERVE_BRK() ends up being more complex than
one would expect to work around a cluster of gcc infelicities:
The first attempt was to simply try putting __section(.brk_reservation)
on a variable. This doesn't work because it ends up making it a
@progbits section, which gets actual space allocated in the vmlinux
executable.
The second attempt was to emit the space into a section using asm,
but gcc doesn't allow arguments to be passed to file-level asm()
statements, making it hard to pass in the size.
The final attempt is to wrap the asm() in a function to allow
it to have arguments, and put the function itself into the
.discard section, which vmlinux*.lds drops entirely from the
emitted vmlinux.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: simplification
We only need to map the kernel in head_32.S, not the whole of
lowmem. We use 512MB as a reasonable (but arbitrary) limit on
the maximum size of the kernel image.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: use new interface instead of previous ad hoc implementation
Use extend_brk() to allocate memory for DMI rather than having an
ad-hoc allocator.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: use new interface instead of previous ad hoc implementation
Rather than having special purpose init_pg_table_start/end variables
to delimit the kernel pagetable built by head_32.S, just use the brk
mechanism to extend the bss for the new pagetable.
This patch removes init_pg_table_start/end and pg0, defines __brk_base
(which is page-aligned and immediately follows _end), initializes
the brk region to start there, and uses it for the 32-bit pagetable.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: new interface
Add a brk()-like allocator which effectively extends the bss in order
to allow very early code to do dynamic allocations. This is better than
using statically allocated arrays for data in subsystems which may never
get used.
The space for brk allocations is in the bss ELF segment, so that the
space is mapped properly by the code which maps the kernel, and so
that bootloaders keep the space free rather than putting a ramdisk or
something into it.
The bss itself, delimited by __bss_stop, ends before the brk area
(__brk_base to __brk_limit). The kernel text, data and bss is reserved
up to __bss_stop.
Any brk-allocated data is reserved separately just before the kernel
pagetable is built, as that code allocates from unreserved spaces
in the e820 map, potentially allocating from any unused brk memory.
Ultimately any unused memory in the brk area is used in the general
kernel memory pool.
Initially the brk space is set to 1MB, which is probably much larger
than any user needs (the largest current user is i386 head_32.S's code
to build the pagetables to map the kernel, which can get fairly large
with a big kernel image and no PSE support). So long as the system
has sufficient memory for the bootloader to reserve the kernel+1MB brk,
there are no bad effects resulting from an over-large brk.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Provide the x86 trace callbacks to trace syscalls.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
LKML-Reference: <1236401580-5758-3-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
We are removing cpumask_t in favour of struct cpumask: mainly as a
marker of what code is now CONFIG_CPUMASK_OFFSTACK-safe.
The only non-trivial change here is vector_allocation_domain():
explicitly clear the mask and set the first word, rather than using
assignment.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Impact: reduce kernel memory usage when CONFIG_CPUMASK_OFFSTACK=y
Straightforward conversion: done for 32 and 64 bit kernels.
node_to_cpumask_map is now a cpumask_var_t array.
64-bit used to be a dynamic cpumask_t array, and 32-bit used to be a
static cpumask_t array.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Impact: cleanup
We take the 64-bit code and use it on 32-bit as well. The new file
is called mm/numa.c.
In a minor cleanup, we use cpu_none_mask instead of declaring a local
cpu_mask_none.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Impact: implement new API
We define arch_send_call_function_ipi_mask and generic kernel/smp.c
code creates arch_send_call_function_ipi() as a wrapper.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Impact: reduce per-cpu size for CONFIG_CPUMASK_OFFSTACK=y
In most places it's cleaner to use the accessors cpu_sibling_mask()
and cpu_core_mask() wrappers which already exist.
I couldn't avoid cleaning up the access in oprofile, either.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Impact: 32/64-bit consolidation
In a first step, this allows fixing phys_addr_valid() for PAE (which
until now reported all addresses to be valid). Subsequently, this will
also allow simplifying some MTRR handling code.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <49B9101E.76E4.0078.0@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix potential oops during app-initiated LDT manipulation
The underlying hypercall has differing argument requirements on 32-
and 64-bit.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
LKML-Reference: <49B9061E.76E4.0078.0@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
