Just as Artem suggested:
"Both UBI and JFFS2 are able to read verify what they wrote already.
There are also MTD tests which do this verification. So I think there
is no reason to keep this in the NAND layer, let alone wasting RAM in
the driver to support this feature. Besides, it does not work for sub-pages
and many drivers have it broken. It hurts more than it provides benefits."
So kill MTD_NAND_VERIFY_WRITE entirely.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is an implemention of hardware ECC write page function which may return an
error indication.
For instance, using Atmel HW PMECC to write one page into a nand flash, the hardware
engine will compute the BCH ecc code for this page. so we need read a the
status register to theck whether the ecc code is generated.
But we cannot assume the status register always can be ready, for example,
incorrect hardware configuration or hardware issue, in such case we need
write_page() to return a error code.
Since the definition of 'write_page' function in struct nand_ecc_ctrl is 'void'.
So this patch will:
1. add return 'int' value for 'write_page' function.
2. to be consitent, add return 'int' value for 'write_page_raw' fuctions too.
3. add code to test the return value, and if negative, indicate an
error happend when write page with ECC.
4. fix the compile warning in all impacted nand flash driver.
Note: I couldn't compile-test all of these easily, as some had ARCH dependencies.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Previously the remove method was looping and removing all chips,
which is obviously not the right thing to do — left over from when
the driver was organized differently and that was the remove method for
the entire controller. This would result in bad things happening if
you have more than one NAND chip, and remove the module.
This also fixes priv->dev to properly point to the chip's device rather than
the controller's. Until now priv->dev was only used for error/debug prints
(and it's an improvement there), so this shouldn't break anything.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
According to its documentation, the NAND_NO_READRDY option is always used
when autoincrement is not supported. Autoincrement support was recently
dropped, so we can drop this options as well (defaulting to "no read ready
check").
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Don't read OOB if the caller doesn't require it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
New NAND controllers can perform read/write via HW engines which don't expose
OOB data in their DMA mode. To reflect this, we should rework the nand_chip /
nand_ecc_ctrl interfaces that assume that drivers will always read/write OOB
data in the nand_chip.oob_poi buffer. A better interface includes a boolean
argument that explicitly tells the callee when OOB data is requested by the
calling layer (for reading/writing to/from nand_chip.oob_poi).
This patch adds the 'oob_required' parameter to each relevant {read,write}_page
interface; all 'oob_required' parameters are left unused for now. The next
patch will set the parameter properly in the nand_base.c callers, and follow-up
patches will make use of 'oob_required' in some of the callee functions.
Note that currently, there is no harm in ignoring the 'oob_required' parameter
and *always* utilizing nand_chip.oob_poi, but there can be
performance/complexity/design benefits from avoiding filling oob_poi in the
common case. I will try to implement this for some drivers which can be ported
easily.
Note: I couldn't compile-test all of these easily, as some had ARCH
dependencies.
[dwmw2: Merge later 1/0 vs. true/false cleanup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ecc.read_page() method for nand drivers is changed to return the maximum
number of bitflips that were corrected on any one region covering an ecc step,
This patch doesn't change what the nand code returns to mtd.
This v2 includes the change to the fsl_ifc_nand driver requested by Scott¹.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040883.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by (freescale changes): Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Flash device drivers initialize 'ecc_strength' in struct mtd_info, which is the
maximum number of bit errors that can be corrected in one writesize region.
Drivers using the nand interface intitialize 'strength' in struct nand_ecc_ctrl,
which is the maximum number of bit errors that can be corrected in one ecc step.
Nand infrastructure code translates this to 'ecc_strength'.
Also for nand drivers, the nand infrastructure code sets ecc.strength for ecc
modes NAND_ECC_SOFT, NAND_ECC_SOFT_BCH, and NAND_ECC_NONE. It is set in the
driver for all other modes.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There was a bug for fmr initialization, which lead to fmr was always 0x100
in fsl_elbc_chip_init() and caused FCM command timeout before calling
fsl_elbc_chip_init_tail(), now we initialize CWTO to maximum timeout value
and not relying on the setting of bootloader.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If we use the Nand flash chip whose number of pages in a block is greater
than 64(for large page), we must treat the low bit of FBAR as being the
high bit of the page address due to the limitation of FCM, it simply uses
the low 6-bits (for large page) of the combined block/page address as the
FPAR component, rather than considering the actual block size.
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When we do a non-full-page write, the length be set to FBCR should
not be 'elbc_fcm_ctrl->index', it should be 'elbc_fcm_ctrl->index -
elbc_fcm_ctrl->column'.
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On both of large-page chip and small-page chip, we always should use
'elbc_fcm_ctrl->oob' to set the FPAR_LP_MS/FPAR_SP_MS bit of FPAR, don't
use a overflowed 'column' to set it.
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch converts the drivers in drivers/mtd/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The eLBC NAND driver currently follows up each program/write operation with a
read-back of the page, in order to [ostensibly] fill in ECC data for the
caller. However, the page address used for this read is always -1, so the read
will never work correctly. Remove this useless (and potentially problematic)
block of code.
Signed-off-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
The global data fsl_lbc_ctrl_dev->nand don't have to be freed in
fsl_elbc_chip_remove(). The right place to do that is in fsl_elbc_nand_remove()
if elbc_fcm_ctrl->counter is zero.
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Recall the recently added prefix requirements:
* "NAND_" for flags in nand.h, used in nand_chip.options
* "NAND_BBT_" for flags in bbm.h, used in nand_chip.bbt_options
or in nand_bbt_descr.options
Thus, I am changing NAND_USE_FLASH_BBT to NAND_BBT_USE_FLASH.
Again, this flag is found in bbm.h and so should NOT be used in the
"nand_chip.options" field.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch works with the following three flags from two headers (nand.h
and bbm.h):
(1) NAND_USE_FLASH_BBT (nand.h)
(2) NAND_USE_FLASH_BBT_NO_OOB (nand.h)
(3) NAND_BBT_NO_OOB (bbm.h)
These flags are all related and interdependent, yet they were in
different headers. Flag (2) is simply the combination of (1) and (3) and
can be eliminated.
This patch accomplishes the following:
* eliminate NAND_USE_FLASH_BBT_NO_OOB (i.e., flag (2))
* move NAND_USE_FLASH_BBT (i.e., flag (1)) to bbm.h
It's important to note that because (1) and (3) are now both found in
bbm.h, they should NOT be used in the "nand_chip.options" field.
I removed a small section from the mtdnand DocBook because it referes to
NAND_USE_FLASH_BBT in nand.h, which has been moved to bbm.h.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
when nand_get_flash_type() is called, it will read 8 bytes of ID instead of 5,
but the driver only read 5 bytes, so kernel will dump error messages like:
fsl-lbc ffe124000.localbus: read_byte beyond end of buffer
fsl-lbc ffe124000.localbus: read_byte beyond end of buffer
fsl-lbc ffe124000.localbus: read_byte beyond end of buffer
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch should fix the following problem:
1. the jffs2-image update in the u-boot was ok
2. first restart and first mount of the NAND-flash-partition was also ok
3. before the restart of controller there are no any activity on NAND-flash except of the jffs2_gcd_mtdX-process ...
4. BUT after the second restart the NAND-flash-partition could not be really used after the second mount,
dmesg filled with messages:
...
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x03ce0000: 0xc0ff instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x03d00000: 0xc0ff instead
....
Just for for info:
the behaviour observed on mpc8313-based board with the large-page NAND.
The only activity on NAND-flash was the garbage collector process, that looks for CLEANMARKER-nodes
As Scott said it was broken by commit 3ab8f2a2e7
Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
--
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When system uses 36bit physical address, res.start is 36bit
physical address. But the function of in_be32 returns 32bit
physical address. Then both of them compared each other is
wrong. So by converting the address of res.start into
the right format fixes this issue.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move Freescale elbc interrupt from nand driver to elbc driver.
Then all elbc devices can use the interrupt instead of ONLY nand.
For former nand driver, it had the two functions:
1. detecting nand flash partitions;
2. registering elbc interrupt.
Now, second function is removed to fsl_lbc.c.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We want error information even if the kernel hasn't been built for verbose
debugging.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently, the program and erase sequences do not wait for completion,
instead relying on a subsequent waitfunc() callback. However, this causes
the chipselect to be deasserted while the NAND chip is still asserting the
busy pin, which can corrupt activity on other chipselects.
This patch switches to using the sequences recommended by the manual,
in which a wait is performed within the initial command sequence. We can
now re-use the status byte from the initial command sequence, rather than
having to do another status read in the waitfunc.
Since we're already touching the command sequences, it also cleans up some
cruft in SEQIN that isn't needed since we cannot program partial pages
outside of OOB.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reported-by: Suchit Lepcha <suchit.lepcha@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When a NAND operation is in progress, all other localbus operations
(including NOR flash) will have to wait for access to the bus. However, the
NAND operation may take longer to complete than the default timeout. Thus,
if NOR is accessed while a NAND operation is in progress, the NAND operation
will fail.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs. The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
These are all powerpc specific drivers.
res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit. Thanks to Scott Wood for noticing.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ECCM maybe set in bootloader, Get ECCM settings from the bootloader,
can avoid the image written by bootloader cannot read out by kernel.
But the limitation of doing it this way is that, it could break large page
NAND if it is written with NAND disabled in u-boot and read with NAND
enabled, or vice versa.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/nand/fsl_elbc_nand.c:890: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With CONFIG_MTD_OF_PARTS=y I'm getting this new section mismatch in reference
from the function fsl_elbc_chip_probe() to the function
.devinit.text:of_mtd_parse_partitions()
This patch fixes the mismatch by providing __devinit annotation to the
fsl_elbc_chip_probe() function.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch deletes oobavail assignments, they're calculated by the nand
core code in nand_scan_tail, plus current oobavail values are wrong for
the LP NANDs.
Also remove mtd->ecclayout and mtd->oobavail assignments, mtd core
handles this all by itself.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch implements support for flash-based BBT for chips working
through ELBC NAND controller, so that NAND core will not have to re-scan
for bad blocks on every boot.
Because ELBC controller may provide HW-generated ECCs we should adjust
bbt pattern and bbt version positions in the OOB free area.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For large page chips, nand_bbt is looking into OOB area, and checking
for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be
reserved for bbt means.
But ELBC driver is specifying ecclayout so that oobfree area starts at
offset 1, so only one byte left for the bbt purposes.
This causes problems with any OOB users, namely JFFS2: after first mount
JFFS2 will fill all OOBs with "erased marker", so OOBs will contain:
OOB Data: ff 19 85 20 03 00 ff ff ff 00 00 08 ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
And on the next boot, NAND core will rescan for bad blocks, then will
see "0xff 0x19" pattern, and will mark all blocks as bad ones.
To fix the issue we should implement our own bad block pattern: just one
byte at OOB start. Though, this will work only for x8 chips. For x16
chips two bytes must be checked. Since ELBC driver does not support x16
NANDs (yet), we're safe for now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
WARNING: drivers/mtd/nand/built-in.o(.devinit.text+0x114): Section mismatch
in reference from the function fsl_elbc_ctrl_probe() to the function
.devexit.text:fsl_elbc_ctrl_remove()
__devinit functions should not call functions with __devexit. Since probe
function calls remove in case of errors, we want to remove __devexit
attribute from it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Using current driver elbc sometimes hangs during nand write. Reading back
last byte helps though (thanks to Scott Wood for the idea).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix a race condition in fsl_elbc_run_command
Fix incorrect usage of clearbits32 that bashed option register
Remove work around for bashed register
Signed-off-by: Mike Hench <mhench@elutions.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Currently fsl_elbc_nand doesn't initialize mtd->name, and this causes
nand_get_flash_type() to assign name that is equal to chip type, like
this:
root@b1:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00010000 "fe000000.flash"
mtd1: 02000000 00004000 "NAND 32MiB 3,3V 8-bit"
mtd0 is physmap_of flash (normal name), and mtd1 is fsl_elbc_nand.
Despite inconsistency, with mtd name like this specifying paritions
from the kernel command line becomes a torture (though, I didn't tried
and not sure if mtdparts= can handle spaces at all). Plus, this causes
real bugs when multiple fsl_elbc_nand chips registered.
With this patch applied fsl_elbc_nand chip will have proper name:
root@b1:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00010000 "fe000000.flash"
mtd1: 02000000 00004000 "e0600000.flash"
p.s. We can't use priv->dev->bus_id as in physmap_of, because
fsl_elbc_nand pretends to be a localbus controller, so its bus_id is
"address.localbus", which is incorrect and thus will also not work
for multiple chips.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
