This patch adds regression tests for testing the kgdb core and arch
specific implementation.
The kgdb test suite is designed to be built into the kernel and not as
a module because it uses a number of low level kernel and kgdb
primitives which should not be exported externally.
The kgdb test suite is designed as a KGDB I/O module which
simulates the communications that a debugger would have with kgdb.
The tests are broken up in to a line by line and referenced here as
a "get" which is kgdb requesting input and "put" which is kgdb
sending a response.
The kgdb suite can be invoked from the kernel command line
arguments system or executed dynamically at run time. The test
suite uses the variable "kgdbts" to obtain the information about
which tests to run and to configure the verbosity level. The
following are the various characters you can use with the kgdbts=
line:
When using the "kgdbts=" you only choose one of the following core
test types:
A = Run all the core tests silently
V1 = Run all the core tests with minimal output
V2 = Run all the core tests in debug mode
You can also specify optional tests:
N## = Go to sleep with interrupts of for ## seconds
to test the HW NMI watchdog
F## = Break at do_fork for ## iterations
S## = Break at sys_open for ## iterations
NOTE: that the do_fork and sys_open tests are mutually exclusive.
To invoke the kgdb test suite from boot you use a kernel start
argument as follows:
kgdbts=V1 kgdbwait
Or if you wanted to perform the NMI test for 6 seconds and do_fork
test for 100 forks, you could use:
kgdbts=V1N6F100 kgdbwait
The test suite can also be invoked at run time with:
echo kgdbts=V1N6F100 > /sys/module/kgdbts/parameters/kgdbts
Or as another example:
echo kgdbts=V2 > /sys/module/kgdbts/parameters/kgdbts
When developing a new kgdb arch specific implementation or
using these tests for the purpose of regression testing,
several invocations are required.
1) Boot with the test suite enabled by using the kernel arguments
"kgdbts=V1F100 kgdbwait"
## If kgdb arch specific implementation has NMI use
"kgdbts=V1N6F100
2) After the system boot run the basic test.
echo kgdbts=V1 > /sys/module/kgdbts/parameters/kgdbts
3) Run the concurrency tests. It is best to use n+1
while loops where n is the number of cpus you have
in your system. The example below uses only two
loops.
## This tests break points on sys_open
while [ 1 ] ; do find / > /dev/null 2>&1 ; done &
while [ 1 ] ; do find / > /dev/null 2>&1 ; done &
echo kgdbts=V1S10000 > /sys/module/kgdbts/parameters/kgdbts
fg # and hit control-c
fg # and hit control-c
## This tests break points on do_fork
while [ 1 ] ; do date > /dev/null ; done &
while [ 1 ] ; do date > /dev/null ; done &
echo kgdbts=V1F1000 > /sys/module/kgdbts/parameters/kgdbts
fg # and hit control-c
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Create <linux/atmel_tc.h> based on <asm-arm/arch-at91/at91-tc.h> and the
at91sam9263 and at32ap7000 datasheets. Most AT91 and AT32 SOCs have one
or two of these TC blocks, which include three 16-bit timers that can be
interconnected in various ways.
These TC blocks can be used for external interfacing (such as PWM and
measurement), or used as somewhat quirky sixteen-bit timers.
Changes relative to the original version:
* Drop unneeded inclusion of <linux/mutex.h>
* Support an arbitrary number of TC blocks
* Return a struct with information about a TC block from
atmel_tc_alloc() instead of using a combination of return values
and "out" parameters.
* ioremap() the I/O registers on allocation
* Look up clocks and irqs for all channels
* Add "name" parameter to atmel_tc_alloc() and use this when
requesting the iomem resource.
* Check if the platform provided the necessary resources at probe()
time instead of when the TCB is allocated.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
PWM device setup, and a simple PWM driver exposing a programming interface
giving access to each channel's full capabilities. Note that this doesn't
support starting several channels in synch.
[hskinnemoen@atmel.com: allocate platform device dynamically]
[hskinnemoen@atmel.com: Kconfig fix]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The enclosure misc device is really just a library providing sysfs
support for physical enclosure devices and their components.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is based on the 2004 out-of-tree work of Jamey Hicks, to add
support via WMI for controlling the jog dial and wireless on these
tablets.
v1:
Original release
v2:
As per Joshua Wise's comments, change bluetooth to jogdial (an error from
the original driver).
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
CC: Matthew Garrett <mjg59@srcf.ucam.org>
CC: Jamey Hicks <jamey.hicks@nokia.com>
CC: Joshua Wise <joshua@joshuawise.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is a driver for newer Acer (and Wistron) laptops. It adds wireless
radio and bluetooth control, and on some laptops, exposes the mail LED and
LCD backlight.
v1:
* Initial release
v2:
* Replace left over ACPI references with WMI
* Add GUID based autoloading (depends on future work to WMI)
* Add DMI based autoloading (backup solution until WMI sysfs/ class
work is available)
* Checkpatch fixes
v3:
* Add new EC quirks for Aspire 3100 & 5100, and Extensa 5220
v4:
* Simplified internal handling of WMID and AMW0 devices
* Add autodetection for bluetooth and maximum brightness on AMW0 V2 and
WMID laptops.
v5:
* Add EC quirk for Medion MD 98000
* Add autodetection for AMW0, and mail LED on AMW0 and AMW0 V2.
* Improve error handling
* Fix AMW0 V2 bluetooth and wireless, by using both WMID and AMW0 methods
to ensure that the correct value is always set.
v6:
* Fix 'use before initialisation' bug with quirks.
v7
* Fix bug on AMW0 where acer-wmi would exit if a mail LED was not
detected.
* Add Acer Aspire 9110 mail LED support
* Fix section mismatch warnings
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
CC: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Intel menlow platform specific driver for thermal management extension.
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (41 commits)
ACPICA: hw: Don't carry spinlock over suspend
ACPICA: hw: remove use_lock flag from acpi_hw_register_{read, write}
ACPI: cpuidle: port idle timer suspend/resume workaround to cpuidle
ACPI: clean up acpi_enter_sleep_state_prep
Hibernation: Make sure that ACPI is enabled in acpi_hibernation_finish
ACPI: suppress uninitialized var warning
cpuidle: consolidate 2.6.22 cpuidle branch into one patch
ACPI: thinkpad-acpi: skip blanks before the data when parsing sysfs
ACPI: AC: Add sysfs interface
ACPI: SBS: Add sysfs alarm
ACPI: SBS: Add ACPI_PROCFS around procfs handling code.
ACPI: SBS: Add support for power_supply class (and sysfs)
ACPI: SBS: Make SBS reads table-driven.
ACPI: SBS: Simplify data structures in SBS
ACPI: SBS: Split host controller (ACPI0001) from SBS driver (ACPI0002)
ACPI: EC: Add new query handler to list head.
ACPI: Add acpi_bus_generate_event4() function
ACPI: Battery: add sysfs alarm
ACPI: Battery: Add sysfs support
ACPI: Battery: Misc clean-ups, no functional changes
...
Fix up conflicts in drivers/misc/thinkpad_acpi.[ch] manually
The Synchronous Serial Controller (SSC) on Atmel microprocessors are
capable of tranceiving many frame based protocols, like I2S. Tested on the
AT32AP7000/ATSTK1000.
This driver is used in the ALSA sound driver for the AT73C213 external DAC
on the ATSTK1000 development board for AVR32. This sound driver will be
submitted soon.
Hardware documentation can be found in the AT32AP7000 data sheet, which can
be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
[akpm@linux-foundation.org: init spinlock at compile time]
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Patrice Vilchez <patrice.vilchez@rfo.atmel.com>
Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a library for reading from 93cx6 eeproms.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yeah, we could have just disabled it, but there's work on a new one that
isn't as fundamentally broken, so there really doesn't seem to be any
point in keeping it around.
The recent timer cleanup broke the only valid use, and when I say
"valid", I obviously mean "totally broken". So it's not like it works,
or really even can work in the current format that uses the unsafe
"panic" LED blinking routines..
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple driver that blinks the keyboard LEDs when loaded. Useful for
checking that the kernel is still alive or for crashdumping
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since ibm-acpi was renamed to thinkpad-acpi, rename and update its Kconfig
entries and Kconfig-related symbols accordingly.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Rename the ibm-acpi driver to thinkpad-acpi. ThinkPads are not even made
by IBM anymore, so it is high time to rename the driver...
The name thinkpad-acpi was used sometime ago by a thinkpad-specific hotkey
driver by Erik Rigtorp, around the 2.6.8-2.6.10 time frame. The driver
apparently never got merged into mainline (it did make some trips through
-mm). ibm-acpi was merged soon after, making its debut in 2.6.10.
The reuse of the thinkpad-acpi name shouldn't be a problem as far as user
confusion goes, as Erik's thinkpad-acpi apparently didn't get widespread
use in the Linux ThinkPad community and most hits for thinkpad-acpi in
google point to ibm-acpi anyway.
Erik, if you read this, please consider the reuse of the thinkpad-acpi name
as a compliment to your effort to make ThinkPads more useful to all of us.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
ibm-acpi is not an ACPICA driver, so move it to drivers/misc as per Len
Brown's request.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Move drivers/acpi/sony_acpi.c to drivers/misc/sony-laptop.c with all the
necessary configuration.
The SONY_LAPTOP config option substitutes the old ACPI_SONY and is 'default n'
now.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Adds the new driver and make ASUS_LAPTOP and ACPI_ASUS
incompatible. It may be strange to use ASUS_CREATE_DEVICE_ATTR
and ASUS_SET_DEVICE_ATTR now, but these macro will be very
usefull in next patchs. ASUS_HANDLE and ASUS_HANDLE_INIT comes
from IBM_HANDLE and IBM_HANDLE_INIT, with some modification,
and will also be used in next patchs.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
The SGI PCI-RT card, based on the SGI IOC4 chip, will be made available on
Altix XE (x86_64) platforms in the near future. As such it is now a
misnomer for the IOC4 base device driver to live under drivers/sn, and
would complicate builds for non-SN2.
This patch moves the IOC4 base driver code from drivers/sn to drivers/misc,
and updates the associated Makefiles and Kconfig files to allow building on
non-SN2 configs. Due to the resulting change in link order, it is now
necessary to use late_initcall() for IOC4 subdriver initialization.
[akpm@osdl.org: __udivdi3 fix]
[akpm@osdl.org: fix default in Kconfig]
Acked-by: Pat Gefre <pfg@sgi.com>
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create a driver to support the platform-specific features
of MSI S270 laptops (and maybe other MSI laptops).
This driver implements a backlight device for controlling LCD brightness
(/sys/class/backlight/msi-laptop-bl/).
In addition it allows access to the WLAN and Bluetooth states
through a platform driver (/sys/devices/platform/msi-laptop-pf/).
Signed-off-by: Lennart Poettering <mzxreary@0pointer.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Cc: Daniel Qarras <dqarras@yahoo.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A simple module to test Linux Kernel Dump mechanism. This module uses
jprobes to install/activate pre-defined crash points. At different crash
points, various types of crashing scenarios are created like a BUG(),
panic(), exception, recursive loop and stack overflow. The user can
activate a crash point with specific type by providing parameters at the
time of module insertion. Please see the file header for usage
information. The module is based on the Linux Kernel Dump Test Tool by
Fernando <http://lkdtt.sourceforge.net>.
This module could be merged with mainline. Jprobes is used here so that the
context in which crash point is hit, could be maintained. This implements
all the crash points as done by LKDTT except the one in the middle of
tasklet_action().
Signed-off-by: Ankita Garg <ankita@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
