* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
net: Fix routing tables with id > 255 for legacy software
sky2: Hold RTNL while calling dev_close()
s2io iomem annotations
atl1: fix suspend regression
qeth: start dev queue after tx drop error
qeth: Prepare-function to call s390dbf was wrong
qeth: reduce number of kernel messages
qeth: Use ccw_device_get_id().
qeth: layer 3 Oops in ip event handler
virtio: use callback on empty in virtio_net
virtio: virtio_net free transmit skbs in a timer
virtio: Fix typo in virtio_net_hdr comments
virtio_net: Fix skb->csum_start computation
ehea: set mac address fix
sfc: Recover from RX queue flush failure
add missing lance_* exports
ixgbe: fix typo
forcedeth: msi interrupts
ipsec: pfkey should ignore events when no listeners
pppoe: Unshare skb before anything else
...
Without simpleImage% in the BOOT_TARGETS list, it is impossible to
build any of the simpleImages.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Step 8.5 in RFC 4340 says for the newly cloned socket
Initialize S.GAR := S.ISS,
but what in fact the code (minisocks.c) does is
Initialize S.GAR := S.ISR,
which is wrong (typo?) -- fixed by the patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This fixes a bug in computing the inter-packet-interval t_ipi = s/X:
scaled_div32(a, b) uses u32 for b, but in "scaled_div32(s, X)" the type of the
sending rate `X' is u64. Since X is scaled by 2^6, this truncates rates greater
than 2^26 Bps (~537 Mbps).
Using full 64-bit division now.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This fixes a bug in the reverse lookup of p: given a value f(p), instead of p,
the function returned the smallest tabulated value f(p).
The smallest tabulated value of
10^6 * f(p) = sqrt(2*p/3) + 12 * sqrt(3*p/8) * (32 * p^3 + p)
for p=0.0001 is 8172.
Since this value is scaled by 10^6, the outcome of this bug is that a loss
of 8172/10^6 = 0.8172% was reported whenever the input was below the table
resolution of 0.01%.
This means that the value was over 80 times too high, resulting in large spikes
of the initial loss interval, thus unnecessarily reducing the throughput.
Also corrected the printk format (%u for u32).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This fixes an oversight from an earlier patch, ensuring that Ack Vectors
are not processed on request sockets.
The issue is that Ack Vectors must not be parsed on request sockets, since
the Ack Vector feature depends on the selection of the (TX) CCID. During the
initial handshake the CCIDs are undefined, and so RFC 4340, 10.3 applies:
"Using CCID-specific options and feature options during a negotiation
for the corresponding CCID feature is NOT RECOMMENDED [...]"
And it is not even possible: when the server receives the Request from the
client, the CCID and Ack vector features are undefined; when the Ack finalising
the 3-way hanshake arrives, the request socket has not been cloned yet into a
full socket. (This order is necessary, since otherwise the newly created socket
would have to be destroyed whenever an option error occurred - a malicious
hacker could simply send garbage options and exploit this.)
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch fixes the following sparse warnings:
* nested min(max()) expression:
net/dccp/ccids/ccid3.c:91:21: warning: symbol '__x' shadows an earlier one
net/dccp/ccids/ccid3.c:91:21: warning: symbol '__y' shadows an earlier one
* Declaration of function prototypes in .c instead of .h file, resulting in
"should it be static?" warnings.
* Declared "struct dccpw" static (local to dccp_probe).
* Disabled dccp_delayed_ack() - not fully removed due to RFC 4340, 11.3
("Receivers SHOULD implement delayed acknowledgement timers ...").
* Used a different local variable name to avoid
net/dccp/ackvec.c:293:13: warning: symbol 'state' shadows an earlier one
net/dccp/ackvec.c:238:33: originally declared here
* Removed unused functions `dccp_ackvector_print' and `dccp_ackvec_print'.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
In commit $(825de27d9e) (from 27th May, commit
message `dccp ccid-3: Fix "t_ipi explosion" bug'), the CCID-3 window counter
computation was fixed to cope with RTTs < 4 microseconds.
Such RTTs can be found e.g. when running CCID-3 over loopback. The fix removed
a check against RTT < 4, but introduced a divide-by-zero bug.
All steady-state RTTs in DCCP are filtered using dccp_sample_rtt(), which
ensures non-zero samples. However, a zero RTT is possible on initialisation,
when there is no RTT sample from the Request/Response exchange.
The fix is to use the fallback-RTT from RFC 4340, 3.4.
This is also better than just fixing update_win_count() since it allows other
parts of the code to always assume that the RTT is non-zero during the time
that the CCID is used.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Most legacy software do not like tables > 255 as rtm_table is u8
so tb_id is sent &0xff and it is possible to mismatch for example
table 510 with table 254 (main).
This patch introduces RT_TABLE_COMPAT=252 so the code uses it if
tb_id > 255. It makes such old applications happy, new
ones are still able to use RTA_TABLE to get a proper table id.
Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using vendor magic to force the PHY into power save mode breaks
suspend. It isn't needed anyway, so remove it.
Tested-by: Avuton Olrich <avuton@gmail.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In case the xmit function drop out with an error, we have to wake
the netdevice queue to start another xmit.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Prepare-function to call s390dbf was wrong handling variable arguments.
This worked as macro but not as function any more.
Now using va_list processing.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unnecessary messages. Write important debug information to
s390dbf.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Get the devno from the ccw device via ccw_device_get_id() instead
of parsing the bus_id.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ip event handler may present us non qeth network interfaces.
Add qeth card pointer check.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
virtio_net uses a timer to free old transmitted packets, rather than
leaving callbacks enabled all the time. If the host promises to
always notify us when the transmit ring is empty, we can free packets
at that point and avoid the timer.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
virtio_net currently only frees old transmit skbs just
before queueing new ones. If the queue is full, it then
enables interrupts and waits for notification that more
work has been performed.
However, a side-effect of this scheme is that there are
always xmit skbs left dangling when no new packets are
sent, against the Documentation/networking/driver.txt
guideline:
"... it is not allowed for your TX mitigation scheme
to let TX packets "hang out" in the TX ring unreclaimed
forever if no new TX packets are sent."
Add a timer to ensure that any time we queue new TX
skbs, we will shortly free them again.
This fixes an easily reproduced hang at shutdown where
iptables attempts to unload nf_conntrack and nf_conntrack
waits for an skb it is tracking to be freed, but virtio_net
never frees it.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
hdr->csum_start is the offset from the start of the ethernet
header to the transport layer checksum field. skb->csum_start
is the offset from skb->head.
skb_partial_csum_set() assumes that skb->data points to the
ethernet header - i.e. it computes skb->csum_start by adding
the headroom to hdr->csum_start.
Since eth_type_trans() skb_pull()s the ethernet header,
skb_partial_csum_set() should be called before
eth_type_trans().
(Without this patch, GSO packets from a guest to the world outside the
host are corrupted).
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
eHEA has to call firmware functions in order to change the mac address
of a logical port. This patch checks if the logical port is up
when calling the register / deregister mac address calls. If the port
is down these firmware calls would fail and are therefore not executed.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
RX queue flush can fail if traffic continues to arrive. Recover by
performing an invisible reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add a workaround for lost MSI interrupts. There is a race condition in
the HW in which future interrupts could be missed. The workaround is to
toggle the MSI irq mask.
Added cleanup based on comments from Andrew Morton.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When pfkey has no km listeners, it still does a lot of work
before finding out there aint nobody out there.
If a tree falls in a forest and no one is around to hear it, does it make
a sound? In this case it makes a lot of noise:
With this short-circuit adding 10s of thousands of SAs using
netlink improves performance by ~10%.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes several issues:
Use the right openprom device name so the driver is actually loaded.
Fix a crash due to unitialized info->pseudo_palette.
Put the framebuffer in the proper mode for software rendering.
checkpatch cleanups.
Hardware acceleration was removed when the driver was rewritten
for the new framebuffer API in 2003. Software rendering requires
a different framebuffer access mode but that wasn't changed. The
driver now works again but is slow. The proper fix is to reintroduce
hardware acceleration.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to unshare the skb first as otherwise pskb_may_pull may
write to a shared skb which could be bad.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The length field in the PPPOE header wasn't checked completely.
This patch causes all packets shorter than the declared length
to be dropped.
It also changes the memcpy_toiovec call to skb_copy_datagram_iovec
so that paged packets (rare for PPPOE) are handled properly.
Thanks to Ilja of the Netric Security Team for discovering and
reporting this bug, and Chris Wright for the total_len check.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. creating proc entry and not saving pointer to PDE and checking it
is not going to work.
2. if proc entry wasn't created, no reason to remove it on error path.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
KERNEL_OFFSET macro in eni.h is not required as it is not used anywhere.
Remove the unused macro from eni.h header file.
Signed-off-by: Pradeep Singh <rautelap@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun noticed that we may call reqsk_free on request sock objects where
the opt fields may not be initialized, fix it by introducing inet_reqsk_alloc
where we initialize ->opt to NULL and set ->pktopts to NULL in
inet6_reqsk_alloc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- The tcp_unhash() method in /include/net/tcp.h is no more needed, as the
unhash method in tcp_prot structure is now inet_unhash (instead of
tcp_unhash in the
past); see tcp_prot structure in net/ipv4/tcp_ipv4.c.
- So, this patch removes tcp_unhash() declaration from include/net/tcp.h
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a potential memory corruption in
pppol2tp_recvmsg(). If skb->len is bigger than the caller's buffer
length, memcpy_toiovec() will go into unintialized data on the kernel
heap, interpret it as an iovec and start modifying memory.
The fix is to change the memcpy_toiovec() call to
skb_copy_datagram_iovec() so that paged packets (rare for PPPOL2TP)
are handled properly. Also check that the caller's buffer is big
enough for the data and set the MSG_TRUNC flag if it is not so.
Reported-by: Ilja <ilja@netric.org>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch limits BLK_DEV_HD_ONLY to the ARM platforms offering
IRQ_HARDDISK, fixing the following compile error on others:
<-- snip -->
...
CC drivers/ide/legacy/hd.o
...
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c: In function 'hd_times_out':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:542: error: 'IRQ_HARDDISK' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:542: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:542: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c: In function 'do_hd_request':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:661: error: 'IRQ_HARDDISK' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c: In function 'hd_init':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:765: error: 'IRQ_HARDDISK' undeclared (first use in this function)
make[3]: *** [drivers/ide/legacy/hd.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't fail the probe if there are no devices attached to the controller.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info - as a nice side-effect
this fixes racy setup of ->io_32bit/unmask settings (after ide_device_add()
call device can be already in use).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hwif->dev was set too late (after ide_device_add() call)
so hwif->gendev.parent was not initialized properly.
Fix it by setting hw.dev and letting ide_init_port_hw()
do the rest.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_find_port() now depends on ->chipset being set for occupied ide_hwifs[]
slots so all host drivers have to initialize hwif->chipset properly.
This patch fixes a regression on hosts with > 1 port or with a single port
but no devices attached to it for an affected host drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hwif->chipset need to be set properly or ide-generic driver will break once
we make a final step in fixing host drivers' dependence on ide_hwifs[].
Problem was catched early thanks to IDE tree exposure in -mm / -next trees
and reported by people listed people (thank you guys!).
Reported-by: "John Keller" <jpk@sgi.com>
Reported-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Reported-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
