ACPI and APM used "pm_active" to guarantee that
they would not be simultaneously active.
But pm_active was recently moved under CONFIG_PM_LEGACY,
so that without CONFIG_PM_LEGACY, pm_active became a NOP --
allowing ACPI and APM to both be simultaneously enabled.
This caused unpredictable results, including boot hangs.
Further, the code under CONFIG_PM_LEGACY is scheduled
for removal.
So replace pm_active with pm_flags.
pm_flags depends only on CONFIG_PM,
which is present for both CONFIG_APM and CONFIG_ACPI.
http://bugzilla.kernel.org/show_bug.cgi?id=9194
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
It is important that these resources be reserved
to avoid conflicts with well known ACPI registers.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When PCI IDE controller works in legacy mode and no PRT entry is found
in ACPI PRT table, OSPM will neither read the irq number from the IDE
PCI configuration space nor call the function of acpi_register_gsi to
register gsi.
http://bugzilla.kernel.org/show_bug.cgi?id=5637
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata and starting/stopping ATAPI floppy devices
sata_sil24: prevent hba lockup when pass-through ATA commands are used
Update kernel parameter document for libata DMA mode setting knobs.
libata: don't normalize UNKNOWN to NONE after reset
libata-pmp: propagate timeout to host link
libata-pmp: 4726 hates SRST
pata_ixp4xx_cf: fix compilation introduced by ata_port_desc() conversion
pata_pdc202xx_old: Further fixups
libata-sff: PCI IRQ handling fix
sata_qstor: use hardreset instead of softreset
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
trm290: do hook dma_host_{on,off} methods (take 2)
ide: fix cable detection for SATA bridges
ide: workaround suspend bug for ACPI IDE
Using default methods caused the chip's DMA PRD count registers, inadvertently
starting DMA! While fixing it, also do:
- get rid of the 'ide_' prefixes in several functions for which the prefix in
the method's name has been 'ide_' ectomized already;
- align the code hooking the IDE DMA methods in init_hwif_trm290()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
http://bugzilla.kernel.org/show_bug.cgi?id=9673
ACPI _PS3 cause S4 breaks in the second attempt. The system has a _PS3
method for IDE, which will call into SMM mode. Currently we haven't clue
why just the second attempt fails, as it's totally in BIOS code, so
blacklist the system so far for 2.6.24.
A possible suspect is ACPI NVS isn't save/restore, we will revisit the
bug after linux does ACPI NVS save/restore.
Bart:
- fix scripts/checkpatch.pl complaints
- const-ify ide_acpi_dmi_table[]
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix commands timeout with Sil3124/3132 based HBA when pass-through ATA
commands [where ATA_QCFLAG_RESULT_TF is set] are used while other
commands are active on other devices connected to the same port with a
Port Multiplier. Due to a hardware bug, these commands must be sent
alone, like ATAPI commands.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After non-classifying reset, ehc->classes[] could contain
ATA_DEV_UNKNOWN which used to be normalized to ATA_DEV_NONE for
consistency. However, this causes unfortunate side effect for drivers
which have non-classifying hardresets (e.g. sata_nv) by making
hardreset report ATA_DEV_NONE for non-classifying resets and thus
makes EH believe that the port is unoccupied and recovery can be
skipped. The end result is that after a device is swapped with
another one, the new device isn't attached after the old one is
detached.
This patch makes ata_eh_reset() not normalize UNKNOWN to NONE after
non-classifying resets. This fixes the above problem. As UNKNOWN and
NONE are handled differently by only EH hotplug logic, this doesn't
cause other behavior changes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Timeout on downstream command may indicate transmission problem on
host link. Propagate timeouts to host link.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turns out distros always enabled burst mode and it is pretty essential so
do the same. Also sort out the post DMA mode restore properly.
My 20263 card now seems happy but needs some four drive tests done yet
(when I've persuaded the kernel not to hang in the edd boot code if I
plug them in ..)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It is legitimate (although annoying and silly) for a PCI IDE controller
not to be assigned an interrupt and to be polled. The libata-sff code
should therefore not try and request IRQ 0 in this case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During conversion to new EH, sata_qstor was accidentaly changed to use
softreset, which is buggy on this chip, instead of hardreset. This
patch updates sata_qstor such that it uses hardreset again.
This fixes bugzilla bug 9631.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The previous patch fixed spurious read faults from occuring by copying
the data if we happen to have a single block at the end of a page. It
appears that gcc cannot guarantee 16-byte alignment in the kernel with
__attribute__. The following report from Torben Viets shows a buffer
that's only 8-byte aligned:
> eneral protection fault: 0000 [#1]
> Modules linked in: xt_TCPMSS xt_tcpmss iptable_mangle ipt_MASQUERADE
> xt_tcpudp xt_mark xt_state iptable_nat nf_nat nf_conntrack_ipv4
> iptable_filter ip_tables x_tables pppoe pppox af_packet ppp_generic slhc
> aes_i586
> CPU: 0
> EIP: 0060:[<c035b828>] Not tainted VLI
> EFLAGS: 00010292 (2.6.23.12 #7)
> EIP is at aes_crypt_copy+0x28/0x40
> eax: f7639ff0 ebx: f6c24050 ecx: 00000001 edx: f6c24030
> esi: f7e89dc8 edi: f7639ff0 ebp: 00010000 esp: f7e89dc8
Since the hardware must have 16-byte alignment, the following patch fixes
this by open coding the alignment adjustment.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There's an error remaining in the 32 bit descriptor code after the
conversion to dma accessors: req_cnt is left uninitialised.
qla1280_32bit_start_scsi gives the following warnings:
drivers/scsi/qla1280.c: In function 'qla1280_32bit_start_scsi':
drivers/scsi/qla1280.c:3044: warning: unused variable 'dma_handle'
drivers/scsi/qla1280.c: In function 'qla1280_queuecommand':
drivers/scsi/qla1280.c:3060: warning: 'req_cnt' is used uninitialized in this function
drivers/scsi/qla1280.c:3042: note: 'req_cnt' was declared here
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
cn_queue_free_callback() will touch 'dev'(i.e. cbq->pdev), so it
should be called before atomic_dec(&dev->refcnt).
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For cards that initially have the MAC address stored in reverse order,
the forcedeth driver uses a flag to signal whether the address was
already corrected, so that it is not reversed again on a subsequent
probe.
Unfortunately this flag, which is stored in a register of the card,
seems to get lost during suspend, resulting in the MAC address being
reversed again. To fix that, the MAC address needs to be written back
in reversed order before we suspend and the flag needs to be reset.
The flag is still required because at least kexec will never write
back the reversed address and thus needs to know what state the card
is in.
Signed-off-by: Bjrn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_control_msg was changed long ago (2.6.12-pre) to take milliseconds
instead of jiffies. Oddly, mcs7830 wasn't added until 2.6.19-rc3.
Signed-off-by: Russ Dill <Russ.Dill@asu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in 2.6.12-pre, usb_start_wait_urb was switched over to take
milliseconds instead of jiffies. kaweth.c was never updated to match.
Signed-off-by: Russ Dill <Russ.Dill@asu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the ->poll() routines of the E100, E1000, E1000E, IXGB, and
IXGBE drivers complete ->poll() consistently.
Now they will all break out when the amount of RX work done is less
than 'budget'.
At a later time, we may want put back code to include the TX work as
well (as at least one other NAPI driver does, but by in large NAPI
drivers do not do this). But if so, it should be done consistently
across the board to all of these drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
When we add the generic napi_disable_pending() breakout
logic to net_rx_action() it means that napi_disable()
can cause NAPI poll interrupt events to be disabled.
And this is exactly what we want. If a napi_disable()
is pending, and we are looping in the ->poll(), we want
->poll() event interrupts to stay disabled and we want
to complete the NAPI poll ASAP.
When ->poll() break out during device down was being handled on a
per-driver basis, often these drivers would turn interrupts back on
when '!netif_running()' was detected.
And this would just cause a reschedule of the NAPI ->poll() in the
interrupt handler before the napi_disable() could get in there and
grab the NAPI_STATE_SCHED bit.
The vast majority of drivers don't care if napi_disable() might have
the side effect of disabling NAPI ->poll() event interrupts. In all
such cases, when a napi_disable() is performed, the driver just
disabled interrupts or is about to.
However there were three exceptions to this in PCNET32, R8169, and
SKY2. To fix those cases, at the subsequent napi_enable() points, I
added code to ensure that the ->poll() interrupt events are enabled in
the hardware.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Don Fry <pcnet32@verizon.net>
This will make sure that always the correct core is selected, even if
there are both a PCI and PCI-E core on a PCI or PCI-E card.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers do this to try to break out of the ->poll()'ing loop
when the device is being brought administratively down.
Now that we have a napi_disable() "pending" state we are going
to solve that problem generically.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the parsing of the RX data header channel field.
The current code parses the header incorrectly and passes a wrong
channel number and frequency for each frame to mac80211.
The FIXMEs added by this patch don't matter for now as the code
where they live won't get executed anyway. They will be fixed later.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should fix the kernel warn/oops reported while routing.
The tulip driver has a fencepost bug with new NAPI in 2.6.24
It has an off by one bug if a full quantum is reached.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
meth didn't set a valid mac address during probing, but later during
open. Newer kernel refuse to open device with 00:00:00:00:00:00 as mac
address -> dead ethernet. This patch sets the mac address in the probe
function and uses only the mac address from the netdevice struct when
setting up the hardware.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was missed when commit e2ac455a18
fixed the compile errors in drivers/net/netx-eth.c caused by
commit 09f75cd7bf.
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the TX ring to have packets sit in it for unbounded
amounts of time.
The only way to defer TX interrupts in the chip is to periodically set
"mark" bits, when processing of a TX descriptor with the mark bit set
is complete it triggers the interrupt for the TX queue's LDG.
A consequence of this kind of scheme is that if packet flow suddenly
stops, the remaining TX packets will just sit there.
If this happens, since those packets could be charged to TCP socket
send queues, such sockets could get stuck.
The simplest solution is to divorce the socket ownership of the packet
once the device takes the SKB, by using skb_orphan() in
niu_start_xmit().
In hindsight, it would have been much nicer if the chip provided two
interrupt sources for TX (like basically every other ethernet chip
does). Namely, keep the "mark" bit, but also signal the LDG when the
TX queue becomes completely empty. That way there is no need to have
a deadlock breaker like this.
Signed-off-by: David S. Miller <davem@davemloft.net>
niu_slowpath_interrupt() expects values to be setup in lp->{v0,v1,v2}
but they aren't. That's only done by niu_schedule_napi() which is
done later in the interrupt path.
If niu_rx_error() returns zero, and v0 is clear, hit the
RX_DMA_CTL_STATE register with a RX_DMA_CTL_STAT_MEX.
Only emit verbose RX error logs if a fatal channel or port error is
signalled. Other cases will be recorded into statistics by
niu_log_rxchan_errors().
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleaning out all the incorrect 'no change made' checks for termios
settings showed up a problem with the PL2303. The hardware here seems to
lose sync and bits if you tell it to make no changes. This shows up with
a real world application.
To fix this the driver check for meaningful hardware changes is restored
but doing the tests correctly and as a tty layer function so it doesn't
get duplicated wrongly everywhere if other drivers turn out to need it.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Mirko Parthey <mirko.parthey@informatik.tu-chemnitz.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc 3.2 has a hard time coping with the code in dmi_id_init():
drivers/built-in.o(.init.text+0x789e): In function `dmi_id_init':
: undefined reference to `__you_cannot_kmalloc_that_much'
make: *** [.tmp_vmlinux1] Error 1
Moving half of the code to a separate function seems to help. This is a
no-op for gcc 4.1 which will successfully inline the code anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Dave Airlie <airlied@linux.ie>
Tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We currently do not wait for the block from the missing device to be
computed from parity before copying data to the new stripe layout.
The change in the raid6 code is not techincally needed as we don't delay
data block recovery in the same way for raid6 yet. But making the change
now is safer long-term.
This bug exists in 2.6.23 and 2.6.24-rc
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a glitch reported by lockdep in the spi_bitbang code: it needs to
consistently block IRQs when holding that spinlock.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
