I am using a Xircom CEM33 pcmcia NIC which has occasional hardware problems.
If the netdev watchdog detects a transmit timeout, do_reset is called which
msleeps - this is illegal in atomic context.
This patch schedules the timeout handling as a workqueue item.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
'mdio_reset' has bad side effects that moves the phy_id.
DL10022-based cards work properly without 'mdio_reset'.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Enable the com20020_cs arcnet driver to see the SoHard (now Mercury
Computer Systems Inc.) SH ARC-PCMCIA card.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
First of all it is unnecessary to allocate a new skb in skb_pad since
the existing one is not shared. More importantly, our hard_start_xmit
interface does not allow a new skb to be allocated since that breaks
requeueing.
This patch uses pskb_expand_head to expand the existing skb and linearize
it if needed. Actually, someone should sift through every instance of
skb_pad on a non-linear skb as they do not fit the reasons why this was
originally created.
Incidentally, this fixes a minor bug when the skb is cloned (tcpdump,
TCP, etc.). As it is skb_pad will simply write over a cloned skb. Because
of the position of the write it is unlikely to cause problems but still
it's best if we don't do it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
hi,
coverity choked at this check (id #223), assuming that
skb might be NULL and used anyways later. Since
start_hard_xmit() always gets called with a valid
skb, the check is useless and this patch removes it.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Florin Malita <fmalita@gmail.com>
The skb may be gone after netif_rx(), we can't use 'skb->len' to update the
stats. 'pkt_len' should work instead.
Coverity CID: 911.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The boot cmdline is parsed in parse_early_param() and
parse_args(,unknown_bootoption).
And __setup() is used in obsolete_checksetup().
start_kernel()
-> parse_args()
-> unknown_bootoption()
-> obsolete_checksetup()
If __setup()'s callback (->setup_func()) returns 1 in
obsolete_checksetup(), obsolete_checksetup() thinks a parameter was
handled.
If ->setup_func() returns 0, obsolete_checksetup() tries other
->setup_func(). If all ->setup_func() that matched a parameter returns 0,
a parameter is seted to argv_init[].
Then, when runing /sbin/init or init=app, argv_init[] is passed to the app.
If the app doesn't ignore those arguments, it will warning and exit.
This patch fixes a wrong usage of it, however fixes obvious one only.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of the two status values struct pcmcia_device->p_state and state,
use descriptive bitfields. Most value-checking in drivers was invalid, as
the core now only calls the ->remove() (a.k.a. detach) function in case the
attachement _and_ configuration was successful.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Most of the driver initialization isn't done in the .probe function, but in
the internal _config() functions. Make them return a value, so that .probe
can properly report whether the probing of the device succeeded or not.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
dev_link_t * and client_handle_t both mean struct pcmcai_device * by now.
Therefore, remove all such indirections.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Embed dev_link_t into struct pcmcia_device(), as they basically address the
same entity. The actual contents of dev_link_t will be cleaned up step by step.
This patch includes a bugfix from and signed-off-by Andrew Morton.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As we do not allow setting Vcc in the pcmcia core, and Vpp1 and
Vpp2 can only be set to the same value, a lot of code can be
streamlined.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Handle the _modifying_ operation sm91c92_cs requires in
pcmcia_modify_configuration, so that the only remaining users
of pcmcia_release_configuration() are within the pcmcia core
module.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In all but one case, the suspend and resume functions of PCMCIA drivers
contain mostly of calls to pcmcia_release_configuration() and
pcmcia_request_configuration(). Therefore, move this code out of the
drivers and into the core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Convert the remaining drivers which use pcmcia_release_io or
pcmcia_release_irq, and remove the EXPORT of these symbols.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_disable_device(struct pcmcia_device *p_dev) performs the necessary
cleanups upon device or driver removal: it calls the appropriate
pcmcia_release_* functions, and can replace (most) of the current drivers'
_release() functions.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The axnet_cs driver can support the AMB8110 PC Card, so add the id for it.
In the old pcmcia-cs config file, this card is listed with the comment "not
specific enough". The last entry in the axnet_ids has the same comment.
They are disabled, and for good reason as it was originally identified by
the MANFID, and that is shared with several cards that use both the
pcnet_cs driver and axnet_cs driver. I tried my AMB8110 with pcnet_cs, and
found that it works fine, and I cannot find a reason for either, except
that the old config file recommended axnet_cs.
Signed-off-by: Jesse Allen <the3dfxdude@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
They deal with wrapping correctly and are nicer to read. Also make
jiffies-holding variables unsigned long.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Unify the EVENT_CARD_INSERTION and "attach" callbacks to one unified
probe() callback. As all in-kernel drivers are changed to this new
callback, there will be no temporary backwards-compatibility. Inside a
probe() function, each driver _must_ set struct pcmcia_device
*p_dev->instance and instance->handle correctly.
With these patches, the basic driver interface for 16-bit PCMCIA drivers
now has the classic four callbacks known also from other buses:
int (*probe) (struct pcmcia_device *dev);
void (*remove) (struct pcmcia_device *dev);
int (*suspend) (struct pcmcia_device *dev);
int (*resume) (struct pcmcia_device *dev);
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The linked list of devices managed by each PCMCIA driver is, in very most
cases, unused. Therefore, remove it from many drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Unify the "detach" and REMOVAL_EVENT handlers to one "remove" function.
Old functionality is preserved, for the moment.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the suspend and resume methods out of the event handler, and into
special functions. Also use these functions for pre- and post-reset, as
almost all drivers already do, and the remaining ones can easily be
converted.
Bugfix to include/pcmcia/ds.c
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Some older DL10019 based cards need to setup
the auto-negotiation-advertisement register
to advertise 100Full,100Half,10Full and 10Half.
Signed-off-by: <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The smc91c92_cs multicast does not work
if the count of multicast address is 1.
Signed-off-by: <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The multicast code of the fmvj18x_cs driver is broken.
I fixed it to work properly.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If the product-id-string contains the '+' , '&' ,'_', it was not converted
properly from the /etc/pcmcia/config(pcmcia-cs config file).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Use of the time_after() macro, defined at linux/jiffies.h, which deal
with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a follow-up, remove the inclusion of pcmcia/version.h in many files.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the "event handler" to struct pcmcia_driver -- the unified event handler
will disappear really soon, but switching it to struct pcmcia_driver in the
meantime allows for better "step-by-step" patches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add new pcmcia id_table for fmvj18x_cs and serial_cs.
(TDK multi-function card (NetPartner9610 and MobileNetworker3200))
Signed-off-by: Jun Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
