Add the em2870 to the list of known em28xx chip ids.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This cleans-up the advise/acquire methods.
This has been tested on the hvr-1300/4000 and assumed to be
correct on the hvr-3000.
This update also fixes analogue tuning on the hvr-1300
when in blackbird mode.
Signed-off-by: Darron Broad <darron@kewl.org>
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changes/fixes on em28xx dev->lock:
- em28xx_init_dev() were unlocking without a previous lock;
- some read ioctls need to lock after the removal of KBL, since a write
may be happening at the same time an ioctl is reading;
- keep the device locked during all device initialization;
- lock/unlock while reading/writing registers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vidioc_try_fmt_vid_cap() just checks if a given resolution is supported.
It doesn't touch on struct em28xx device descriptor. so, there's no need
to lock.
While there, use unlikely() for those values that aren't likely to
occur.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for absolute and continuous zoom controls (mapped to absolute
and relative UVC zoom controls).
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update v4l2_ctrl_get_name() and v4l2_ctrl_get_menu() with missing
control names and menu values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Refine the firmware load and firmware startup process. Significant changes
are to ensure the SCB and IPC area are correct before starting up the firmware,
and letting the CPU firmware start up the APU firmware for us.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Use a known open task handle when setting stream CX2341x parameters
Sometimes, we might only have VBI or YUV stream open instead of an MPEG stream.
Let's make sure we use a valid task handle to perform the CX2341x control
settings.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VBI comment corrections to avoid future confusion about standards.
Comments on cx18 VBI implementation shortcomings that need resolution.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed magic number that referred to firmware limit on the number of
MDLs the firmware can maintain for any stream at any one time.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original version of sccb_read_reg() is from Jim Paris.
NOTE: as it is now reading sensor ID won't work for sensors on different
i2c slave address.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The vc0321 sends some additional data after sending the complete
frame, we ignore this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for getting and setting framerate via v4l2 controls,
rather than setting a fixed value at module insertion.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add get_streamparm and set_streamparm operations so subdrivers can
get/set stream parameters such as framerate.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set frame format registers 0x0a and 0x0b to explicit values
rather than relying on reset-time defaults.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frame data in bulk transfers is separated into 2048-byte payloads.
Each payload has its own header.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This sensor was declared as hdcs2020.
The new exchanges have been extracted from the ms-win file usbvm31b.inf.
The light frequency control has been added.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch moves the last fid and pts from static to the sd structure.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The indirect registers at 0x1c/0x1d control frame settings. If we
leave the values at 0x0a and 0x0b at their reset-time defaults, frame
data from the camera matches the UVC payload format. This lets us
better reassemble the data into frames and know when data was lost.
This also lets us relax the bulk_size requirement from 600K to 2K,
which should help systems on with limited RAM (like the PS3).
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The frame size is too small, so we lose the last YUYV pixel.
Fix the setup and remove the last_pixel hack.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The colors control (saturation) acted as color balance.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The brightness jumped from max to min at the middle of the control values.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add helper functions to load i2c sub-devices, integrating them
into the v4l2-framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a driver for the OMAP2 camera block. OMAP2 is used in e.g. Nokia
N800/N810 internet tablet.
This driver uses the V4L2 internal ioctl interface.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bogus controls currently include processing unit auto controls for which no
corresponding manual control is available. Such auto controls make little
sense if any, and are known to crash at least the SiGma Micro webcam.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver drops incomplete uncompressed video frames to avoid confusing
userspace with corrupt data. Add a nodrop module parameter to turn that
behaviour off and make all frames available to userspace.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A combined authorship patch from Hans Verkuil and Andy Walls. Raw
VBI can now be captured but requires a video capture to be in progress as well.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a port of the fixes Hans Verkuil made for ivtv/cx25840:
The service_set field was used to determine whether raw or sliced VBI was
desired. This is incorrect since it is perfectly valid to select sliced VBI
with a service_set of 0.
Instead the driver should check on VIDIOC_S_FMT whether the type
field matches the raw or sliced VBI type.
Updated the cx18 driver accordingly, including an additional check in
cx18_start_v4l2_encode_stream() that didn't exist in ivtv.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Avoid making firmware API calls with the queue lock held. The source
of MPEG strem corruption when not holding the queue lock was found to be that
the MPEG buffer could be retrieved by the user app before it was sync'ed for
the host cpu. Incoming buffers are now sync'ed before being put on q_full and
releasing the queue lock. We can thus avoid the sometimes lengthy call to
the firmware for CPU_DE_SET_MDL while holding the queue lock, so we can get
better performance.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Increment version number due to siginificant buffering changes.
Now version 1.0.4
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Add module parameters for finer control over buffer allocations.
User now has the option of setting smaller buffers to get lower
latency transfers from the encoder. User can also now set the number
of buffers used for a stream explicitly.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Allow more than 63 capture buffers in rotation per stream. Implement
q_busy to hold buffers the firmware has for use. q_free holds truly unused
buffers in a pool. New buffers are given to the firmware as soon as the
firmware returns one, if there are any to give to the firmware.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Eliminate q_io from stream buffer handling in anticipation of upcoming
changes in buffer handling. q_io was a holdover from ivtv and it's function
in cx18 was trivial and not necessary. We just push things back onto the
front of q_full now, instead of maintaining a 1 buffer q_io queue.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
How to enable the mpeg encoder is not found yet.
The card comes up with gpio 0x0820000 for DVB-T.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the function cx88_audio_initdev, the value card has been created using
snd_card_new. The other error handling code in this function frees the
value using snd_card_free. I have thus changed the first error case to do
the same. On the other hand, it may be that card is not sufficiently
initialized at this point to use snd_card_free, in which case something
else should be done to free the memory in the error case.
In the function snd_cx88_create the call kfree(chip) in one error case
looks suspicious, both because it is not done in the other error code, and
because chip points into the middle of the memory allocated by
snd_card_new, ie it is not itself associated with a separate kmalloc.
Therefore I have removed it.
The semantic match that finds the first problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S,S1;
position p1,p2,p3;
expression E,E1;
type T,T1;
expression *ptr != NULL;
@@
(
if ((x@p1 = snd_card_new(...)) == NULL) S
|
x@p1 = snd_card_new(...);
)
... when != snd_card_free(...,(T)x,...)
when != if (...) { <+... snd_card_free(...,(T)x,...) ...+> }
when != true x == NULL || ...
when != x = E
when != E = (T)x
when any
(
if (x == NULL || ...) S1
|
if@p2 (...) {
... when != snd_card_free(...,(T1)x,...)
when != if (...) { <+... snd_card_free(...,(T1)x,...) ...+> }
when != x = E1
when != E1 = (T1)x
(
return \(0\|<+...x...+>\|ptr\);
|
return@p3 ...;
)
}
)
@ script:python @
p1 << r.p1;
p3 << r.p3;
@@
print "* file: %s snd_card_new: %s return: %s" % (p1[0].file,p1[0].line,p3[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add Compro VideoMate E650F (DVB-T part only).
The card based on cx23885 PCI-Express chip, xc3028 tuner and ce6353 demodulator.
Cc: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the new format-negotiation infrastructure, support all four YUV422
packed and the planar formats.
The new translation structure enables to build the format
list with buswidth, depth, host format and camera format
checked, so that it's not done anymore on try_fmt nor
set_fmt.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allocate and fill a list of formats, supported by this specific
camera-host combination. Use it for format enumeration. Take care to stay
backwards-compatible.
Camera hosts rely on sensor formats available, as well as
host specific translations. We add a structure so that hosts
can define a translation table and use it for format check
and setup.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We anyway don't follow the s_fmt_vid_cap / g_fmt_vid_cap / try_fmt_vid_cap
naming, and soc-camera is so far only about video capture, let's simplify
operation names a bit further. set_fmt_cap / try_fmt_cap wasn't a very good
choice too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pixel format requested by the user is not necessarily the same, as what
a sensor driver provides. There are situations, when a camera host driver
provides the required format, but requires a different format from the
sensor. Further, the list of formats, supported by sensors is pretty static
and can be pretty good described with a constant list of structures. Whereas
decisions, made by camera host drivers to support requested formats can be
quite complex, therefore it is better to let the host driver do the work.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
.try_bus_param() method from struct soc_camera_host_ops is only called at one
location immediately before .try_fmt_cap(), there is no value in keeping these
two methods separate, merge them.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: cx18_writel_expect() should not declare success on a PCI read error.
This removes the potential for cx18_write*_expect() calls to not
accomplish a PCI write successfully as expected. The CX18-AV core uses the
*expect() calls often and this may be the source of intermittent audio
problems and standands switching problems.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Change to per CX23418 device work queues for deferrable work handling.
Needed to support 2.6.22 and earlier kernels that can't selectively cancel
work orders. Also will provide slightly better performance on SMP systems.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this
development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx devices generally get hot when xc3028 tuner is powered on. This
patch solves this by turning power off when the device is not used, at the
expense of having a higher load time, when calling a TV application.
Since firmware load happens on 1 or 2 seconds on most devices, this is not a pain.
Also, it helps to save the planet by saving some power :)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change log format to look more like URB transactions. In fact, setup and
IN/OUT transactions are merged. This helps to debug the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
