Make pci_setup_device() write the bus ID directly into the allotted storage,
rather than using pci_name() as the address as that now returns a const
pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp driver saves its private data pointer into pci_dev
structure using pci_set_drvdata()/pci_get_drvdata(). But because
pciehp is not a pci device driver but a PCI Express service driver, it
should save its private data pointer into pcie_device structure using
set_service_data()/get_service_data().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, pciehp driver enables command completed interrupt as follows.
(1) Don't enable at initialization.
(2) Enable command completed interrupt whenever pciehp issues a
command, if the command doesn't attempt to disable the interrupt.
(3) Disable command completed interrupt at driver unloading.
Once we enable command completed interrupt, we don't need to re-enable
it for every command. So we can simplify above steps as follows:
(1) Enable command completed interrupt at initialization.
(2) No special sequence for command completed interrupt.
(3) Disable command completed interrupt at driver unloading.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp driver's intialization sequence is as follows:
(1) initialize controller data structure
(2) install interrupt handler
(3) enable software notification
(4) initialize controller specific slot data structure
(5) initialize generic slot data structure and register it to pci hotplug core
The interrupt handler of pciehp assumes that controller specific slot
data structure is already initialized. However, it is installed at (2)
before initializing controller specific slot data structure at
(4). Because of this, pciehp driver cannot handle the following cases
properly.
- If devices that shares IRQ with pciehp raise interrupts between (2) and (4).
- If hotplug events (e.g. MRL open) happen between (3) and (4).
We already have a workaround for this problem ("pciehp: fix NULL
dereference in interrupt handler: dbd79aed1a).
But we still need fundamental fix.
This patch fix the problem by changing the initilization sequence as follows:
(1) initialize controller data structure
(2) initialize controller specific slot data structure
(3) install interrupt handler
(4) enable software notification
(5) initialize generic slot data structure and register it to pci hotplug core
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Convert printks to use dev_printk().
I converted pr_debug() to dev_dbg(). Both use KERN_DEBUG and are enabled
only when DEBUG is defined.
I converted printk(KERN_DEBUG) to dev_printk(KERN_DEBUG), not to dev_dbg(),
because dev_dbg() is only enabled when DEBUG is defined.
I converted DBG(KERN_INFO) (only in setup-bus.c) to dev_info(). The DBG()
name makes it sound like debug, but it's been enabled forever, so dev_info()
preserves the previous behavior.
I tried to make the resource assignment formats more consistent, e.g.,
"BAR %d: got res [%#llx-%#llx] bus [%#llx-%#llx] flags %#lx\n"
instead of sometimes using "start-end" and sometimes using "size@start".
I'm not attached to one or the other; I'd just like them consistent.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pcie_poll_cmd() and pcie_wait_cmd() are too large to be
inlined.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change command polling frequency to 100Hz from 10Hz in order to reduce
the delay in the common case of a command completing quickly.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup pcie_poll_cmd(): check the slot status once before entering our
completion test loop and convert the loop to a simpler while() block.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since the second argument of acpi_pci_choose_state() and
platform_pci_choose_state() is never used, remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Get rid of a superfluous acpi_pm_device_sleep_state() parameter. The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do. (However, this
does not address the fact that ACPI still doesn't set up those flags.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Detect all physical PCI slots as described by ACPI, and create entries in
/sys/bus/pci/slots/.
Not all physical slots are hotpluggable, and the acpiphp module does not
detect them. Now we know the physical PCI geography of our system, without
caring about hotplug.
[kaneshige.kenji@jp.fujitsu.com: export-kobject_rename-for-pci_hotplug_core]
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Greg KH <greg@kroah.com>
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix build with CONFIG_DMI=n]
Signed-off-by: Alex Chiang <achiang@hp.com>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, /sys/bus/pci/slots/ only exposes hotplug attributes when a
hotplug driver is loaded, but PCI slots have attributes such as address,
speed, width, etc. that are not related to hotplug at all.
Introduce pci_slot as the primary data structure and kobject model.
Hotplug attributes described in hotplug_slot become a secondary
structure associated with the pci_slot.
This patch only creates the infrastructure that allows the separation of
PCI slot attributes and hotplug attributes. In this patch, the PCI
hotplug core remains the only user of this infrastructure, and thus,
/sys/bus/pci/slots/ will still only become populated when a hotplug
driver is loaded.
A later patch in this series will add a second user of this new
infrastructure and demonstrate splitting the task of exposing pci_slot
attributes from hotplug_slot attributes.
- Make pci_slot the primary sysfs entity. hotplug_slot becomes a
subsidiary structure.
o pci_create_slot() creates and registers a slot with the PCI core
o pci_slot_add_hotplug() gives it hotplug capability
- Change the prototype of pci_hp_register() to take the bus and
slot number (on parent bus) as parameters.
- Remove all the ->get_address methods since this functionality is
now handled by pci_slot directly.
[achiang@hp.com: rpaphp-correctly-pci_hp_register-for-empty-pci-slots]
Tested-by: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: make headers_check happy]
[akpm@linux-foundation.org: nuther build fix]
[akpm@linux-foundation.org: fix typo in #include]
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Register one slot per slot, rather than one slot per function. Change the
name of the slot to fake%d instead of the pci address.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch unhides the SMBus on Compaq Deskpro EN
SFF P667 with the Intel 815E chipset. Unhiding it reveals
a THMC51 hardware monitoring chip.
Jean Delvare has checked that this machine has no ACPI
magic touching the SMBus nor the hardware monitoring chip,
so this should be safe.
The patch was tested on Fedora Core 9 with 2.6.25.4 kernel.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Rafał Haładuda <rh1985@wp.pl>
CC: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While refreshing my physical PCI slot series against upstream, I
noticed a few simple sparse/compile warnings that were easy to
fix.
Fix the following sparse warnings in PCIe:
drivers/pci/pcie/aer/aerdrv.c:86:6: warning: symbol 'pci_no_aer'
was not declared. Should it be static?
drivers/pci/pcie/portdrv_bus.c:21:17: warning: symbol
'pcie_port_bus_type' was not declared. Should it be static?
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
One more machine with a hidden Intel SMBus. Unhiding it reveals a SMSC
EMC6D100 hardware monitoring chip. I have checked that this machine
has no ACPI magic touching the SMBus nor the hardware monitoring chip,
so this should be safe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The destination of goto error also does a kfree(g_iommus), so it is not
correct to do one here.
This was found using Coccinelle (http://www.emn.fr/x-info/coccinelle/).
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fixup a typo in dbg_ctrl(); it was fetching SLOTSTATUS twice.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the following problems of shpchp driver about getting hotplug
control from firmware.
- The shpchp driver must not control the hotplug controller if it
fails to get control from the firmware. But current shpchp
controls the hotplug controller regardless the result, because it
doesn't check the return value of get_hp_hw_control_from_firmware().
- Current shpchp driver doesn't support _OSC.
The pciehp driver already have the code for evaluating _OSC and OSHP
and shpchp and pciehp can share it. So this patch move that code from
pciehp to acpi_pcihp.c.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since we need to wait for command completion for muximum 1sec, waiting
command should not be interrupted by a signal.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp evaluates _OSC/OSHP method after some controller
initialization is done. So if evaluating _OSC/OSHP is failed, we need
to cleanup already initialized data structures or hardware. This
clearly is not robust way. With this patch, _OSC/OSHP evaluation is
done first.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the redundant initialization of pci_dev member of struct
controller in pciehp_probe(). It is initialized in pcie_init().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Implement new suspend and hibernation callbacks for the PCI bus type.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The position of MSI capability is already cached in the msi_desc when
we enter the msi_set_mask_bits(). Use it instead.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The 'retval' variable in __pci_osc_support_set() is no longer
used. Remove this unused variable.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pci-acpi implementation checks osc_data->support_stat to see
if control bits had been already queried. It is not good from the
viewpoint of easy understanding. So this patch adds new 'is_queried'
flag to indicate query had been done.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pci-acpi implementation uses array in osc_data directly to
evaluate _OSC. It needs to save the old data and restore it if _OSC
evaluation fails. To make it more robust, we should use local array to
evaluate _OSC.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the duplicated code in acpi_query_osc() and acpi_run_osc().
It simplifies the code very much.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If a device supports #PME and can generate PME events from D0, we may see
superfluous events before a driver is loaded (drivers should only enable PME as
needed), preventing suspend from working if the corresponding GPE was enabled.
Likewise, if the ACPI device has the _PRW object, the _PSW/_DSW object will be
called in order to disable the wakeup functionality. But when it is allowed to
wake up the sleeping state, OSPM will enable it again.
So we should disable PME in the course of scanning PCI devices and enable it
again only when PME events are actually required to be generated from the
requested PCI state (for example, D3_hot or D3_cold). It is also safe to
disable PME again when the PME is disabled for the PCI devices.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some quirks should be called with interrupt disabled, we can't directly
call them in .resume_early. Also the patch introduces
pci_fixup_resume_early and pci_fixup_suspend, which matches current
device core callbacks (.suspend/.resume_early).
TBD: Somebody knows why we need quirk resume should double check if a
quirk should be called in resume or resume_early. I changed some per my
understanding, but can't make sure I fixed all.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch makes the needlessly global {pciehp,shpchp}_slot_with_bus
static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When Greg "fixed" the sysfs usage of that driver a while back, he seem
to have introduced a bug where the quotes are added around the name of
our specific sysfs files, thus breaking the user space tool.
This fixes it. Tested DLPAR operations on a POWER6 machine successfully.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The pciehp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the following errors reported by Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
kobject_add_internal failed for 2 with -EEXIST, don't try to register things with the same name in the same directory.
Pid: 1, comm: swapper Tainted: G W 2.6.26-rc3 #1
[<c0266980>] kobject_add_internal+0x140/0x190
[<c0266afd>] kobject_init_and_add+0x2d/0x40
[<c027bc91>] pci_hp_register+0x81/0x2f0
[<c027fd07>] pciehp_probe+0x1a7/0x470
[<c01b3b84>] sysfs_add_one+0x44/0xa0
[<c01b3c1f>] sysfs_addrm_start+0x3f/0xb0
[<c01b497a>] sysfs_create_link+0x8a/0xf0
[<c0279570>] pcie_port_probe_service+0x50/0x80
[<c02e0545>] driver_sysfs_add+0x55/0x70
[<c02e0662>] driver_probe_device+0x82/0x180
[<c02e07cc>] __driver_attach+0x6c/0x70
[<c02dfe0a>] bus_for_each_dev+0x3a/0x60
[<c05db2d0>] pcied_init+0x0/0x80
[<c02e04e6>] driver_attach+0x16/0x20
[<c02e0760>] __driver_attach+0x0/0x70
[<c02e0341>] bus_add_driver+0x1a1/0x220
[<c05db2d0>] pcied_init+0x0/0x80
[<c02e09cd>] driver_register+0x4d/0x120
[<c05db050>] ibm_acpiphp_init+0x0/0x190
[<c0125aab>] printk+0x1b/0x20
[<c05db2d0>] pcied_init+0x0/0x80
[<c05db2de>] pcied_init+0xe/0x80
[<c05c751a>] kernel_init+0x10a/0x300
[<c0120138>] schedule_tail+0x18/0x50
[<c0103b9a>] ret_from_fork+0x6/0x1c
[<c05c7410>] kernel_init+0x0/0x300
[<c05c7410>] kernel_init+0x0/0x300
[<c010485b>] kernel_thread_helper+0x7/0x1c
=======================
pci_hotplug: Unable to register kobject '2'<3>pciehp: pci_hp_register failed with error -22
Slot with the same name can be registered multiple times if shpchp or
pciehp driver is loaded after acpiphp is loaded because ACPI based
hotplug driver and Native OS hotplug driver trying to handle the same
physical slot. In this case, current pci_hotplug core will call
kobject_init_and_add() muliple time with the same name. This is the
cause of this problem. To fix this problem, this patch adds the check
into pci_hp_register() to see if the slot with the same name.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
According to the PCI Express specification, we must wait for at least
1 second after turning power off before taking any action that relies
on power having been removed from the slot/adapter. For this, current
pciehp wait for 1 second after issuing the power off command in
hpc_power_off_slot() function. But waiting for 1 second in
hpc_power_off_slot() can make pciehp probing slow-down because pciehp
probe code calls hpc_power_off_slot() if the slot is not occupied just
in case. We don't need to wait for 1 second at the pciehp probe time
because there is no action on that empty slot. So move 1 second wait
from hpc_power_off_slot() to the caller of hpc_power_off_slot().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix improper long wait for command completion in pciehp probing.
As described in PCI Express specification, software notification is
not generated if the command that occurs as a result of a write to the
Slot Control register that disables software notification of command
completed events. Since pciehp driver doesn't take it into account,
such command is issued in pciehp probing, and it causes improper long
wait for command completion.
This patch changes the pciehp driver to take such command into
account.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the "pciehp probing slow" problem reported from Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
The command completed bit in Slot Status register applies only to
commands issued to control the attention indicator, power indicator,
power controller, or electromechanical interlock. However, writes to
other parts of the Slot Control register would end up writing to the
control fields. Hence, any write to Slot Control register is
considered as a command. However, if the controller doesn't support
any of attention indicator, power indicator, power controller and
electromechanical interlock, command completed bit would not set in
writing to Slot Control register. In this case, we should not wait for
command completed bit set, otherwise all commands would be considered
not completed in timeout seconds (1 sec.).
The cause of the problem is pciehp driver didn't take this situation
into account. This patch changes pciehp to take it into account. This
patch also add the check for "No Command Completed Support" bit in
Slot Capability register. If it is set, we should not wait for command
completed bit set as well.
This problem seems to be revealed by the commit
c27fb883df that fixed the bug that
pciehp did not wait for command completed properly (pciehp just
ignored the command completion event).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The shpchp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
