Its hardware is handled more fully by the new azt1605/azt2316 drivers.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a new driver for Aztech Sound Galaxy ISA soundcards based on the
AZT1605 and AZT2316 chipsets. It's constructed as two seperate drivers
for either chipset generated from the same source file, with (very)
minimal ifdeffery.
The drivers check the SB DSP version to decide if they are being loaded
for the right chip. AZT1605 returns 2.1 by default and AZT2316 3.1.
This isn't full-proof as the DSP version can actually be set through
software but it's close enough -- as far as I've been able to see, the
DSP version can not be stored in the EEPROM and the cards will therefore
startup with the defaults.
This distinction could (with the same success rate) also be used to
decide which chip we're looking at at runtime meaning a single, merged
driver is also an option but I feel it's actually nicer this way. A
merged driver would have to postpone translating the passed in resource
values to the card configuration until it knew which one it was looking
at and would need to postpone erring out on mpu_irq=10 for azt1605 and
mpu_irq=3 for azt2316.
The drivers have been tested on various cards. For snd-azt1605:
FCC-ID I38-MMSN811: Aztech Sound Galaxy Nova 16 Extra
FCC-ID I38-MMSN822: Aztech Sound Galaxy Pro 16 II
and for snd-azt2316:
FCC-ID I38-MMSN824: Aztech Sound Galaxy Pro 16 AB
FCC-ID I38-MMSN826: Trust Sound Expert DeLuxe Wave 32 (05201)
FCC-ID I38-MMSN830: Trust Sound Expert DeLuxe 16+ (05202)
FCC-ID I38-MMSN837: Packard Bell ISA Soundcard 030069
FCC-ID I38-MMSN846: Trust Sound Expert DeLuxe 16-3D (06300)
FCC-ID I38-MMSN847: Trust Sound Expert DeLuxe Wave 32-3D (06301)
FCC-ID I38-MMSN852: Aztech Sound Galaxy Waverider Pro 32-3D
826 and 846 were also marketed directly by Aztech and then known as:
FCC-ID I38-MMSN826: Aztech Sound Galaxy Waverider 32+
FCC-ID I38-MMSN846: Aztech Sound Galaxy Nova 16 Extra II-3D
Together, these cover the AZT1605 and AT2316A, AZT2316R and AZT2316-S
chipsets. All cards work fully -- full-duplex PCM, MIDI and FM. Full
duplex is a little flaky on some.
I38-MSN811 tends to not work in full-duplex but sometimes does with the
highest success rate being achieved when you first start the capture and
then a playback instead of the other way around (it's a CS4231-KL
codec).
The cards with an AD1845XP codec (my I38-MMSN826 and one of my
I38-MMSN830s) are also somewhat duplex-challenged. Sometimes full-duplex
works, sometimes not and this varies from try to try. This seems likely
to be a timing problem somewhere inside wss-lib.
I38-MMSN826 has an additional "ICS2115 WaveFront" wavetable synth
onboard that isn't supported yet. The wavetable synths on I38-MMSN847
and I38-MMSN852 are wired directly to the standard MPU-401 UART and the
AUX1 input on the codec and work without problem.
CD-ROM audio on the cards is routed to the codec "Line" input, Line-In
to its Aux input, and FM/Wavetable to its AUX1 input. I did not rename
the controls due to the capture source enumeration: I see that
capture-source overrides are hardcoded in wss-lib and this is just too
ugly to live.
Versus the old snd-sgalaxy driver these drivers add support for the
models without a configuration EEPROM (which are common), full-duplex,
MPU-401 UART and OPL3. In the future they might grow support for that
ICS2115 WaveFront synth on 826 and an hwdep interface to write to the
EEPROM on the models that have one.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ESS ES968 chip is nothing more then a PnP companion
for a non-PnP audio chip. It was paired with non-PnP ESS' chips:
ES688 and ES1688. The ESS' audio chips are handled by the es1688
driver in native mode. The PnP cards are handled by the ES968
driver in SB compatible mode.
Move the ES968 chip handling to the es1688 driver so the driver
can handle both PnP and non-PnP cards. The es968 is removed.
Also, a new PnP id is added for the card I acquired (the change
was tested on this card).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is one of Sound Blaster Pro compatible chipsets which is supported
by Linux OSS driver and was missing native supoort for ALSA.
The Jazz16 audio codec is Crystal CS4216 which is capable
of playback and recording up to 48 kHz stereo.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The als100 driver is so similar to the dt019x/als007 driver
that one driver's source can be used for both drivers with
only few changes. Merge the dt019x driver into the als100.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The conversion solves the problem that firmware size was set to 64KB
while non PnP cards have 128KB firmware files.
An additional firmware initialization code has been moved from the OSS
driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move code from the OSS sscape driver in order to support old Soundscape OEM models.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for later cards based on CompuMedia ASC-9408 chipsets.
These cards were produced by Gallant.
This patch make the OSS aedsp16 driver redundant.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Always use request_firmware() for loading yss225_registers image.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
cs4232 and cs4236 driver merge to solve PnP BIOS detection.
Also, the patch adds recognition if the chip is cs4236b+
or earlier part. This unifies drivers for both cs4232
and cs4236+ chips. It allows to use the PnP BIOS
detection for the cs4236+ chips. Previously, only
the snd-cs4232 could be detected by the PnP BIOS.
The cs4232+ cards reports two separate PnP BIOS ids.
The patch adds search for the second id to find out
resources assigned to a control port.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is driver for Turtle Beach Multisound cards:
Classic, Fiji and Pinnacle.
Tested pcm playback and recording and MIDI playback
on Multisound Pinnacle.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add OPL3 handling to the driver
and volume control for FM synthesis.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the wss detection code and kill the ad1848 library.
The library is fully assimilated into the new wss library.
This required reworking of the AD1848 family code
so the code is changed to correctly detect chips from
the AD1848 and CS4231 families.
I have tested it on following cards:
Gallant SC-6600 (codec: AD1848, driver: snd-sc6600)
SoundScape VIVO/90 (codec: AD1845, driver: snd-sscape)
SG Waverider (codec: CS4231A, driver: Rene Herman's snd-galaxy)
Opti930 (codec: built-in - CS4231 compatible, driver: snd-opti93x)
Opti931 (codec: built-in - CS4231 compatible, driver: snd-opti93x)
Gallant SC-70P (chip/codec: CS4237B, driver: snd-cs4236)
Audio Plus 3D (chip/codec: CMI8330A, driver: snd-cmi8330)
Dell Latitude CP (chip/codec: cs4236, driver snd-cs4232)
Sound playback and recording works on all these cards.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the wss pcm code and kill the ad1848 pcm code.
The AD1848 chip is much slower than CS4231 chips
so the waiting loop was increased 100x (10x is not
enough).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Move the file sound/isa/cs423x/cs4231_lib.c
into sound/isa/cs423x/wss_lib.c
This is the first step toward merging all libraries
for Windows Sound System compatible chips
into a single library.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch converts the Opti93x driver to use
the cs4231 library instead of duplicating the code.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
After the removal of the sequencer instrument layer SND_GUS_SYNTH was
no longer used.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is port of the Gallant SC-6000 driver from the OSS aedsp16 driver.
This card was also sold as AudioExcel DSP 16 and Zoltrix AV302 (Audio
Plus True 16).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Use the standard firmware loader for loading ICS2115 OS firmware file.
This is the last old bad guy that is still using sys_open() and sys_read()
calls, and now all should be gone.
The patch also adds the missing description of module options related
with wavefront_synth.c.
Due to this rewrite, user will have to copy or make symlink the firmware
file appropriately to the standard firmware path such as /lib/firmware.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes the following compile error with
CONFIG_SND_CS5530=y, CONFIG_ISA=n:
<-- snip -->
...
LD .tmp_vmlinux1
sound/built-in.o: In function 'snd_sb16_capture_trigger':
sb16_main.c:(.text+0x212ad): undefined reference to 'snd_sbdsp_command'
sb16_main.c:(.text+0x212cc): undefined reference to 'snd_sbdsp_command'
sb16_main.c:(.text+0x212f7): undefined reference to 'snd_sbdsp_command'
sound/built-in.o: In function 'snd_sb16_playback_trigger':
sb16_main.c:(.text+0x2136d): undefined reference to 'snd_sbdsp_command'
sb16_main.c:(.text+0x2138c): undefined reference to 'snd_sbdsp_command'
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
A few PCI drivers like ALS4000 and CS5530 require the SB16-codes.
This patch fixes / improves the dependency between SB modules and
PCI drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Since request_firmware() is no longer used when the internal firmware
images are used, it is no longer necessary to depend on FW_LOADER in
this case.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The external firmware files are not in the alsa-plugins but in the
alsa-firmware package.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Move the FW_LOADER dependencies out of the *_FIRMWARE_IN_KERNEL entries
because these drivers use the firmware loader regardless of whether
there is an in-kernel firmware image.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Some drivers are already ifdefs for enabling external firmwares
but not defined in Kconfig. Now they appear as the kernel configs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Load the YSS225 register initialization data using request_firmware(),
if possible, instead of using the built-in data blob.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Load the CSP programs using request_firmware(), if possible, instead of
using the built-in firmware blobs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the missing dependency on CONFIG_SND for snd-adlib driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Attached you'll find an ALSA driver for AdLib FM cards. An AdLib card is
just an OPL2, which was already supported by sound/drivers/opl3, so only
very minimal bus-glue is needed. The patch applies cleanly to both
2.6.16 and 2.6.16-mm1.
The driver has been tested with an actual ancient 8-bit ISA AdLib card
and works fine. It also works fine for an OPL3 {,emulation} as still
found on many ISA soundcards but given that AdLib cards don't have their
own mixer, upping the volume from 0 might be a problem without the card
driver already loaded and driving the OPL3.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In sound/isa/Kconfig, select ISAPNP and depend on ISAPNP are intermixed,
resulting in funny behaviour. (Soundcarts get selectable if other
soundcards are selected).
This patch changes the "depend on ISAPNP"s to select.
Signed-Off-By: Bodo Eggert <7eggert@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
fixed kconfig dependencies on ISA_DMA_API for parts of sound/* that rely
on it.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
