Added missing dev_port assignment in cxgb4vf driver.
Also made dev_port assignment of cxgb4 in sync with cxgb4vf driver.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At bootup we run measurements to calculate the best threshold for when we
should be using full TLB flushes instead of just flushing a specific amount of
TLB entries. This performance test is run over the kernel text segment.
But running this TLB performance test on the kernel text segment turned out to
crash some SMP machines when the kernel text pages were mapped as huge pages.
To avoid those crashes this patch simply skips this test on some SMP machines
and calculates an optimal threshold based on the maximum number of available
TLB entries and number of online CPUs.
On a technical side, this seems to happen:
The TLB measurement code uses flush_tlb_kernel_range() to flush specific TLB
entries with a page size of 4k (pdtlb 0(sr1,addr)). On UP systems this purge
instruction seems to work without problems even if the pages were mapped as
huge pages. But on SMP systems the TLB purge instruction is broadcasted to
other CPUs. Those CPUs then crash the machine because the page size is not as
expected. C8000 machines with PA8800/PA8900 CPUs were not affected by this
problem, because the required cache coherency prohibits to use huge pages at
all. Sadly I didn't found any documentation about this behaviour, so this
finding is purely based on testing with phyiscal SMP machines (A500-44 and
J5000, both were 2-way boxes).
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Helge Deller <deller@gmx.de>
One small fix for a regression in a prior fix (again). This time the
condition in the prior fix BUG_ON proved to be wrong under certain
circumstances causing a BUG to trigger where it shouldn't in the lpfc
driver.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cyir
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One small fix for a regression in a prior fix (again).
This time the condition in the prior fix BUG_ON proved to be wrong
under certain circumstances causing a BUG to trigger where it
shouldn't in the lpfc driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: fix oops/BUG in lpfc_sli_ringtxcmpl_put()
When netdev_upper_dev_unlink failed in ipvlan_link_new, need to
unlink the ipvlan dev with upper dev.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we can't allocate the resources in gigaset_initdriver() then we
should return -ENOMEM instead of zero.
Fixes: 2869b23e4b ("[PATCH] drivers/isdn/gigaset: new M101 driver (v2)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug report from Debian [0] shows there's minor changed model of
Linkstation LS-GL that uses the 2nd SATA port of the SoC.
So it's necessary to enable two SATA ports, though for that specific
model only the 2nd one is used.
[0] https://bugs.debian.org/845611
Fixes: b1742ffa9d ("ARM: dts: orion5x: add device tree for buffalo linkstation ls-gl")
Reported-by: Ryan Tandy <ryan@nardis.ca>
Tested-by: Ryan Tandy <ryan@nardis.ca>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Telit LE922A MBIM based composition does not work properly
with altsetting toggle done in cdc_ncm_bind_common.
This patch adds CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE quirk
to avoid this procedure that, instead, is mandatory for
other modems.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro ZX_SPDIF_CLK_RAT should be 2 instead of 4. With this
fix, we can get correct audio output on HDMI through SPDIF interface.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ZTE ZX SPDIF and I2S drivers can work on not only ZX296702 but also
other ZTE ZX family SoCs like ZX296718, which is an arm64 platform.
Let's make a few renaming and tweak the Kconfig a bit to get the drivers
available for other ZTE ZX platforms.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix for bad memory access while disconnecting. netdev is freed before
private data free, and dev is accessed after freeing netdev.
This makes a slub problem, and it raise kernel oops with slub debugger
config.
Signed-off-by: Jiho Chu <jiho.chu@samsung.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This function sets req->r_locked_dir which is supposed to indicate to
ceph_fill_trace that the parent's i_rwsem is locked for write.
Unfortunately, there is no guarantee that the dir will be locked when
d_revalidate is called, so we really don't want ceph_fill_trace to do
any dcache manipulation from this context. Clear req->r_locked_dir since
it's clearly not safe to do that.
What we really want to know with d_revalidate is whether the dentry
still points to the same inode. ceph_fill_trace installs a pointer to
the inode in req->r_target_inode, so we can just compare that to
d_inode(dentry) to see if it's the same one after the lookup.
Also, since we aren't generally interested in the parent here, we can
switch to using a GETATTR to hint that to the MDS, which also means that
we only need to reserve one cap.
Finally, just remove the d_unhashed check. That's really outside the
purview of a filesystem's d_revalidate. If the thing became unhashed
while we're checking it, then that's up to the VFS to handle anyway.
Fixes: 200fd27c8f ("ceph: use lookup request to revalidate dentry")
Link: http://tracker.ceph.com/issues/18041
Reported-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
In case the user provided insufficient data, the code may return
prematurely without any operation. In this case, the processed
data indicated with outlen is zero.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Merge more fixes from Andrew Morton:
"3 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
kcov: add missing #include <linux/sched.h>
radix tree test suite: fix compilation
zram: restrict add/remove attributes to root only
In __sanitizer_cov_trace_pc we use task_struct and fields within it, but
as we haven't included <linux/sched.h>, it is not guaranteed to be
defined. While we usually happen to acquire the definition through a
transitive include, this is fragile (and hasn't been true in the past,
causing issues with backports).
Include <linux/sched.h> to avoid any fragility.
[mark.rutland@arm.com: rewrote changelog]
Link: http://lkml.kernel.org/r/1481007384-27529-1-git-send-email-wangkefeng.wang@huawei.com
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch "lib/radix-tree: Convert to hotplug state machine" breaks the test
suite as it adds a call to cpuhp_setup_state_nocalls() which is not
currently emulated in the test suite. Add it, and delete the emulation
of the old CPU hotplug mechanism.
Link: http://lkml.kernel.org/r/1480369871-5271-36-git-send-email-mawilcox@linuxonhyperv.com
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Tested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zram hot_add sysfs attribute is a very 'special' attribute - reading
from it creates a new uninitialized zram device. This file, by a
mistake, can be read by a 'normal' user at the moment, while only root
must be able to create a new zram device, therefore hot_add attribute
must have S_IRUSR mode, not S_IRUGO.
[akpm@linux-foundation.org: s/sence/sense/, reflow comment to use 80 cols]
Fixes: 6566d1a32b ("zram: add dynamic device add/remove functionality")
Link: http://lkml.kernel.org/r/20161205155845.20129-1-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Steven Allen <steven@stebalien.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: <stable@vger.kernel.org> [4.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
another regression fix for the shutdown stuff.
* 'drm-fixes-4.9' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: just suspend the hw on pci shutdown
SCT Write Same support had been introduced with
commit 7b20309428 ("libata: Add support for SCT Write Same")
Some problems, namely excessive userspace segfaults, had been reported at
http://lkml.kernel.org/r/20160908192736.GA4356@gmail.com
This lead to commit 0ce1b18c42 ("libata: Some drives failing on
SCT Write Same") which strived to disable SCT Write Same on !ZAC devices.
Due to the way this was done and to the logic in sd_config_write_same(),
this didn't work for those devices that have
->max_ws_blocks > SD_MAX_WS10_BLOCKS: for these, ->no_write_same and
->max_write_same_sectors would still be non-zero,
but ->ws10 == ->ws16 == 0. This would cause sd_setup_write_same_cmnd() to
demultiplex REQ_OP_WRITE_SAME requests to WRITE_SAME, and these in turn
aren't supported by libata-scsi:
EXT4-fs (dm-1): Delayed block allocation failed for inode 2625094 at
logical offset 2032 with max blocks 2 with error 121
EXT4-fs (dm-1): This should not happen!! Data will be lost
121 == EREMOTEIO is what scsi_io_completion() asserts in case of
invalid opcodes.
Back to the original problem of userspace segfaults: this can be tracked
down to ata_format_sct_write_same() overwriting the input page. Sometimes,
this page is ZERO_PAGE(0) which ceases to be filled with zeros from that
point on. Since ZERO_PAGE(0) is used for userspace .bss mappings, code of
the following is doomed:
static char *a = NULL; /* .bss */
...
if (a)
*a = 'a';
This problem is not solved by disabling SCT Write Same for !ZAC devices
only.
It can certainly be fixed, but the final release is quite close -- so
disable SCT Write Same for all ATA devices rather than introducing some
SCT key buffer allocation schemes at this point.
Fixes: 7b20309428 ("libata: Add support for SCT Write Same")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The eLCDIF IP of the i.MX 7 SoC knows multiple clocks and lists them
separately:
Clock Clock Root Description
apb_clk MAIN_AXI_CLK_ROOT AXI clock
pix_clk LCDIF_PIXEL_CLK_ROOT Pixel clock
ipg_clk_s MAIN_AXI_CLK_ROOT Peripheral access clock
All of them are switched by a single gate, which is part of the
IMX7D_LCDIF_PIXEL_ROOT_CLK clock. Hence using that clock also for
the AXI bus clock (clock-name "axi") makes sure the gate gets
enabled when accessing registers.
There seem to be no separate AXI display clock, and the clock is
optional. Hence remove the dummy clock.
This fixes kernel freezes when starting the X-Server (which
disables/re-enables the display controller).
Fixes: e8ed73f691 ("ARM: dts: imx7d: add lcdif support")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
In a previous commit, I made a copy/paste error in the pinmux
definitions of UART3: PG{13,14} instead of PA{13,14}. This commit takes
care of that. I have tested this commit on Orange Pi PC and Orange Pi
Plus, and it works for these boards.
Fixes: e3d11d3c45 ("dts: sun8i-h3: add pinmux definitions for
UART2-3")
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull x86 fixes from Ingo Molnar:
"Misc fixes: a core dumping crash fix, a guess-unwinder regression fix,
plus three build warning fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind: Fix guess-unwinder regression
x86/build: Annotate die() with noreturn to fix build warning on clang
x86/platform/olpc: Fix resume handler build warning
x86/apic/uv: Silence a shift wrapping warning
x86/coredump: Always use user_regs_struct for compat_elf_gregset_t
Pull perf fixes from Ingo Molnar:
"A bogus warning fix, a counter width handling fix affecting certain
machines, plus a oneliner hw-enablement patch for Knights Mill CPUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Remove invalid warning from list_update_cgroup_even()t
perf/x86: Fix full width counter, counter overflow
perf/x86/intel: Enable C-state residency events for Knights Mill
Pull locking fixes from Ingo Molnar:
"Two rtmutex race fixes (which miraculously never triggered, that we
know of), plus two lockdep printk formatting regression fixes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Fix report formatting
locking/rtmutex: Use READ_ONCE() in rt_mutex_owner()
locking/rtmutex: Prevent dequeue vs. unlock race
locking/selftest: Fix output since KERN_CONT changes
Pull objtool fix from Ingo Molnar:
"A single late breaking fix for objtool"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix bytes check of lea's rex_prefix
Commit 3e3aaf6494 ("phy: fix mdiobus module safety") fixed the way we
dealt with MDIO bus module reference count, but sort of introduced a
regression in that, if an Ethernet driver registers its own MDIO bus
driver, as is common, we will end up with the Ethernet driver's
module->refnct set to 1, thus preventing this driver from any removal.
Fix this by comparing the network device's device driver owner against
the MDIO bus driver owner, and only if they are different, increment the
MDIO bus module refcount.
Fixes: 3e3aaf6494 ("phy: fix mdiobus module safety")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hyper-V (and Azure) support using NVGRE which requires some extra space
for encapsulation headers. Because of this the largest allowed TSO
packet is reduced.
For older releases, hard code a fixed reduced value. For next release,
there is a better solution which uses result of host offload
negotiation.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for setting the RGMII_IDMODE bit was added in the commit
referenced below. However, that commit did not add the symmetrical
clearing of the bit by way of setting it in "mask". Add it here.
Note that the documentation marks clearing this bit as "reserved",
however, according to TI, support for delaying the clock does exist in
the MAC, although it is not officially supported.
We tested this on a board with an RGMII to RGMII link that will not
work unless this bit is cleared.
Fixes: 0fb26c3063 ("drivers: net: cpsw-phy-sel: add support to configure rgmii internal delay")
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEES2FAuYbJvAGobdVQPTuqJaypJWoFAlhH2rkTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRA9O6olrKklasABCAClCaAGYAOuMLWXJ9mL1K7o2u+s6M93
bSZQfke8ffFv0vNa35HLH8vXCh3QBl8BEZkN0XuXQwRSiewsWQz/W5hMZ9UcfgdR
lml6v/jaQ0nai5UrdSHJqXwm21e3M/ELFn5dE0esp1p7lSITRAbTPSyN2kNhiGyv
HLMXFPopCGEbInyo+5QA17xTPGUdMNE6J8rnRPKnMzbLgyRgZ3Jwy0furKAbzTY7
4eFiERuBErRB/tD3+oxFICcB5zyvqawnXZp+gsg5o8vm7DGZU4/WXbxOQOgwx1fK
Nw4/9FXPxUxXB925JMIn/bxjNi0OK9M96Q7bMpoa8Ik/CCkV/zKdKxIt
=0RcO
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.9-20161207' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-12-07
Andrey Konovalov triggered a warning in the CAN RAW layer, which is
fixed by a patch by me.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull fuse fix from Miklos Szeredi:
"Fix a regression spotted by Jeff Layton"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix clearing suid, sgid for chown()
This reverts commit 8ab2ae655b.
I loved that commit because of how it explained what the problem with
newer versions of binutils were, but the actual patch itself turns out
to not work very well.
It has two problems:
- a zero CRC value isn't actually right. It happens to work for the
case where both sides of the equation fail at giving the symbol a
crc, but there are cases where the users of the exported symbol get
the right crc (due to seeing the C declarations), but the actual
exporting itself does not (due to the whole weak asm symbol issue).
So then the module load fails after all - we did have a crc for the
symbol, but we couldn't match it with the loaded module.
- it seems that the alpha assembler has special semantics for the
'.set' directive, and on alpha it doesn't actually set the value of
the specified symbol at all, it is instead used to set various
assembly modes (eg ".set noat" and ".set noreorder").
So using ".set" to set the symbol value would just cause build
failures on alpha.
I'm sure we'll find some other workaround for these issues (hopefully
that involves getting rid of modversions entirely some day, but people
are also talking about just using smarter tools). But for now we'll
just fall back on commit faaae2a581 ("Re-enable CONFIG_MODVERSIONS in
a slightly weaker form") that just let's a missing crc through.
Reported-by: Jan Stancek <jstancek@redhat.com>
Reported-by: Philip Müller <philm@manjaro.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In theory we could map other things, but there's a reason that function
is called "user_iov". Using anything else (like splice can do) just
confuses it.
Reported-and-tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current rsnd driver setups BRGCKR/BRRA/BRRB when .probe timing.
But it breaks sound after Suspend/Resume. These should be setups
every start timing.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver enables ADG clock when .probe timing,
but it breaks sound after Suspend/Resume. These should be setups
every suspend/resume timing too.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ssi->usrcnt will be updated on snd_soc_dai_ops::trigger,
but snd_pcm_ops::hw_params will be called *before* it.
Thus, ssi->usrcnt is still 0 when 1st call.
rsnd_ssi_hw_params() needs to check its called count, this means
trigger should be if (ssi->usrcnt) instead of if (ssi->usrcnt > 1).
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Algorithms not compatible with mcryptd could be spawned by mcryptd
with a direct crypto_alloc_tfm invocation using a "mcryptd(alg)" name
construct. This causes mcryptd to crash the kernel if an arbitrary
"alg" is incompatible and not intended to be used with mcryptd. It is
an issue if AF_ALG tries to spawn mcryptd(alg) to expose it externally.
But such algorithms must be used internally and not be exposed.
We added a check to enforce that only internal algorithms are allowed
with mcryptd at the time mcryptd is spawning an algorithm.
Link: http://marc.info/?l=linux-crypto-vger&m=148063683310477&w=2
Cc: stable@vger.kernel.org
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For encryption, the AEAD ciphers require AAD || PT as input and generate
AAD || CT || Tag as output and vice versa for decryption. Prior to this
patch, the AF_ALG interface for AEAD ciphers requires the buffer to be
present as input for encryption. Similarly, the output buffer for
decryption required the presence of the tag buffer too. This implies
that the kernel reads / writes data buffers from/to kernel space
even though this operation is not required.
This patch changes the AF_ALG AEAD interface to be consistent with the
in-kernel AEAD cipher requirements.
Due to this handling, he changes are transparent to user space with one
exception: the return code of recv indicates the mount of output buffer.
That output buffer has a different size compared to before the patch
which implies that the return code of recv will also be different.
For example, a decryption operation uses 16 bytes AAD, 16 bytes CT and
16 bytes tag, the AF_ALG AEAD interface before showed a recv return
code of 48 (bytes) whereas after this patch, the return code is 32
since the tag is not returned any more.
Reported-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Start with a clean slate before dealing with bit 16 (pointer size)
of Master Configuration Register.
This fixes the case of AArch64 boot loader + AArch32 kernel, when
the boot loader might set MCFGR[PS] and kernel would fail to clear it.
Cc: <stable@vger.kernel.org>
Reported-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-By: Alison Wang <Alison.wang@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
mv_cesa_hash_std_step() copies the creq->state into the SRAM at each
step, but this is only required on the first one. By doing that, we
overwrite the engine state, and get erroneous results when the crypto
request is split in several chunks to fit in the internal SRAM.
This commit changes the function to copy the state only on the first
step.
Fixes: commit 2786cee8e5 ("crypto: marvell - Move SRAM I/O op...")
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
No need to copy the template of an hash operation twice into the SRAM
from the step function.
Fixes: commit 85030c5168 ("crypto: marvell - Add support for chai...")
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds a check to limit the number of can_filters that can be
set via setsockopt on CAN_RAW sockets. Otherwise allocations > MAX_ORDER
are not prevented resulting in a warning.
Reference: https://lkml.org/lkml/2016/12/2/230
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We have four routines in pacache.S that use temporary alias pages:
copy_user_page_asm(), clear_user_page_asm(), flush_dcache_page_asm() and
flush_icache_page_asm(). copy_user_page_asm() and clear_user_page_asm()
don't purge the TLB entry used for the operation.
flush_dcache_page_asm() and flush_icache_page_asm do purge the entry.
Presumably, this was thought to optimize TLB use. However, the
operation is quite heavy weight on PA 1.X processors as we need to take
the TLB lock and a TLB broadcast is sent to all processors.
This patch removes the purges from flush_dcache_page_asm() and
flush_icache_page_asm.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Helge Deller <deller@gmx.de>
The attached change interchanges the order of purging the TLB and
setting the corresponding page table entry. TLB purges are strongly
ordered. It occurred to me one night that setting the PTE first might
have subtle ordering issues on SMP machines and cause random memory
corruption.
A TLB lock guards the insertion of user TLB entries. So after the TLB
is purged, a new entry can't be inserted until the lock is released.
This ensures that the new PTE value is used when the lock is released.
Since making this change, no random segmentation faults have been
observed on the Debian hppa buildd servers.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Helge Deller <deller@gmx.de>
Hugh notes in response to commit 4cb19355ea "device-dax: fail all
private mapping attempts":
"I think that is more restrictive than you intended: haven't tried, but I
believe it rejects a PROT_READ, MAP_SHARED, O_RDONLY fd mmap, leaving no
way to mmap /dev/dax without write permission to it."
Indeed it does restrict read-only mappings, switch to checking
VM_MAYSHARE, not VM_SHARED.
Cc: <stable@vger.kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Pawel Lebioda <pawel.lebioda@intel.com>
Fixes: 4cb19355ea ("device-dax: fail all private mapping attempts")
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A recent flurry of bug discoveries in the nfit driver's DSM marshalling
routine has highlighted the fact that we do not have unit test coverage
for this routine. Add a self-test of acpi_nfit_ctl() routine before
probing the "nfit_test.0" device. This mocks stimulus to acpi_nfit_ctl()
and if any of the tests fail "nfit_test.0" will be unavailable causing
the rest of the tests to not run / fail.
This unit test will also be a place to land reproductions of quirky BIOS
behavior discovered in the field and ensure the kernel does not regress
against implementations it has seen in practice.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Given dimms and bus commands share the same command number space we need
to be careful that we are translating status in the correct context.
Otherwise we can, for example, fail an ND_CMD_GET_CONFIG_SIZE command
because max_xfer is zero. It fails because that condition erroneously
correlates with the 'cleared == 0' failure of ND_CMD_CLEAR_ERROR.
Cc: <stable@vger.kernel.org>
Fixes: aef2533822 ("libnvdimm, nfit: centralize command status translation")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If an ARS Status command returns truncated output, do not process
partial records or otherwise consume non-status fields.
Cc: <stable@vger.kernel.org>
Fixes: 0caeef63e6 ("libnvdimm: Add a poison list and export badblocks")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Given ambiguities in the ACPI 6.1 definition of the "Output (Size)"
field of the ARS (Address Range Scrub) Status command, a firmware
implementation may in practice return 0, 4, or 8 to indicate that there
is no output payload to process.
The specification states "Size of Output Buffer in bytes, including this
field.". However, 'Output Buffer' is also the name of the entire
payload, and earlier in the specification it states "Max Query ARS
Status Output Buffer Size: Maximum size of buffer (including the Status
and Extended Status fields)".
Without this fix if the BIOS happens to return 0 it causes memory
corruption as evidenced by this result from the acpi_nfit_ctl() unit
test.
ars_status00000000: 00020000 00000000 ........
BUG: stack guard page was hit at ffffc90001750000 (stack is ffffc9000174c000..ffffc9000174ffff)
kernel stack overflow (page fault): 0000 [#1] SMP DEBUG_PAGEALLOC
task: ffff8803332d2ec0 task.stack: ffffc9000174c000
RIP: 0010:[<ffffffff814cfe72>] [<ffffffff814cfe72>] __memcpy+0x12/0x20
RSP: 0018:ffffc9000174f9a8 EFLAGS: 00010246
RAX: ffffc9000174fab8 RBX: 0000000000000000 RCX: 000000001fffff56
RDX: 0000000000000000 RSI: ffff8803231f5a08 RDI: ffffc90001750000
RBP: ffffc9000174fa88 R08: ffffc9000174fab0 R09: ffff8803231f54b8
R10: 0000000000000008 R11: 0000000000000001 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000003 R15: ffff8803231f54a0
FS: 00007f3a611af640(0000) GS:ffff88033ed00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffc90001750000 CR3: 0000000325b20000 CR4: 00000000000406e0
Stack:
ffffffffa00bc60d 0000000000000008 ffffc90000000001 ffffc9000174faac
0000000000000292 ffffffffa00c24e4 ffffffffa00c2914 0000000000000000
0000000000000000 ffffffff00000003 ffff880331ae8ad0 0000000800000246
Call Trace:
[<ffffffffa00bc60d>] ? acpi_nfit_ctl+0x49d/0x750 [nfit]
[<ffffffffa01f4fe0>] nfit_test_probe+0x670/0xb1b [nfit_test]
Cc: <stable@vger.kernel.org>
Fixes: 747ffe11b4 ("libnvdimm, tools/testing/nvdimm: fix 'ars_status' output buffer sizing")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ACPI DSMs can have an 'extended' status which can be non-zero to convey
additional information about the command. In the xlat_status routine,
where we translate the command statuses, we were returning an error for
a non-zero extended status, even if the primary status indicated success.
Return from each command's 'case' once we have verified both its status
and extend status are good.
Cc: <stable@vger.kernel.org>
Fixes: 11294d63ac ("nfit: fail DSMs that return non-zero status by default")
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
