Setup a proper AGC config for the 340e, based on the Windows USB trace
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a sleep since in some cases the dib7000p wasn't online when being probed.
The optimal timing has not yet been determined.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the correct i2c bus to communicate with the tuner, and properly setup the
reset GPIO and i2c address.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide a frontend setup routine for the PCTV 340e which takes into account
the specific GPIO setup of the board.
Note that this patch does *not* take into account the xc4000 reset pin, which
is attached to the dib7000.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the board profile for the PCTV 340eSE, since that's what I have here
for development.
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is initial code written by Davide Ferri for the PCTV 340e, including
a new xc4000 driver. I am checking in all the code unmodified, and making
no assertions about its quality (other than confirming it compiles).
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Davide Ferri <davidef1986@gmail.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function "rc5_scan" in "dvb_usb.h" is returning invalid value.
The value should be returned "u16" but is returning "u8".
See example below in "drivers/media/dvb/dvb-usb/opera1.c":
send_key = (send_key & 0xffff) | 0x0100;
for (i = 0; i < ARRAY_SIZE(rc_map_opera1_table); i++) {
if (rc5_scan(&rc_map_opera1_table[i]) == (send_key & 0xffff)) {
*state = REMOTE_KEY_PRESSED;
*event = rc_map_opera1_table[i].keycode;
opst->last_key_pressed =
rc_map_opera1_table[i].keycode;
break;
}
opst->last_key_pressed = 0;
}
Signed-off-by: Manoel Pinheiro <pinusdtv@hotmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Basically it is just same device as Anysee E7 S2 but made for
internal PCI(e) slot and motherboard USB connector.
Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Basically it is just same device as Anysee E7 TC but made for
internal PCI(e) slot and motherboard USB connector.
Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] v1.88 DM04/QQBOX Move remote to use rc_core dvb-usb-remote
[media] Add missing include guard to header file
[media] Inlined functions should be static
[media] Remove invalid parameter description
[media] cpia2: fix warning about invalid trigraph sequence
[media] s5p-csis: Add missing dependency on PLAT_S5P
[media] gspca/kinect: wrap gspca_debug with GSPCA_DEBUG
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function
[media] uvcvideo: Connect video devices to media entities
[media] uvcvideo: Register subdevices for each entity
[media] uvcvideo: Register a v4l2_device
[media] add V4L2-PIX-FMT-SRGGB12 & friends to docbook
[media] Documentation/DocBook: Rename media fops xml files
[media] Media DocBook: fix validation errors
[media] wl12xx: g_volatile_ctrl fix: wrong field set
[media] fix kconfig dependency warning for VIDEO_TIMBERDALE
[media] dm1105: GPIO handling added, I2C on GPIO added, LNB control through GPIO reworked
[media] Add support for M-5MOLS 8 Mega Pixel camera ISP
driver to use dvb-usb-remote.
The remote(s) generates 24 bit NEC codes, lme2510 keymaps redefined.
Other minor fixes
fix le warning.
make sure frontend is detached on firmware change.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (247 commits)
[media] gspca - sunplus: Fix some warnings and simplify code
[media] gspca: Fix some warnings tied to 'no debug'
[media] gspca: Unset debug by default
[media] gspca - cpia1: Remove a bad conditional compilation instruction
[media] gspca - main: Remove USB traces
[media] gspca - main: Version change to 2.13
[media] gspca - stk014 / t613: Accept the index 0 in querymenu
[media] gspca - kinect: Remove __devinitdata
[media] gspca - cpia1: Fix some warnings
[media] video/Kconfig: Fix mis-classified devices
[media] support for medion dvb stick 1660:1921
[media] tm6000: fix uninitialized field, change prink to dprintk
[media] cx231xx: Add support for Iconbit U100
[media] saa7134 add new TV cards
[media] Use a more consistent value for RC repeat period
[media] cx18: Move spinlock and vb_type initialisation into stream_init
[media] tm6000: remove tm6010 sif audio start and stop
[media] tm6000: remove unused exports
[media] tm6000: add pts logging
[media] tm6000: change from ioctl to unlocked_ioctl
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
[mchehab@redhat.com: The same patch were sent by Alf and by Randoslaw.
I've applied the oldest version, just fixing the entry index]
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Tested-by: James Huk <huk256@gmail.com>
Tested-by: Alf Fahland <alf-f@gmx.de>
Signed-off-by: Radoslaw Warowny <radoslaww@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bits 4 and 5 on register 02 should always be set to 1.
Opera1/Bsru6/z0194a/mantis_vp1033
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improve PID filtering and program register 20 correctly.
Make sure stream_on message is sent if streaming is off, otherwise
PIDs are not registered.
Move mutex outside lme2510_enable_pid.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_buffer not inside mutex lock, waiting caller can alter buffer.
Static added to lme2510_exit and lme2510_exit_int.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return device errors to demuxer from on/off streamming and
pid filtering.
Please test this patch with all dvb-usb devices.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are a couple of places where mutex_unlock() is called even
if mutex_lock_interruptible() failed. The patch fixes the issue.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A greatly simplified version of the PID Filter now added
back to the Driver.
The driver allows for the PID filter to be turned off.
applied after patch 683781.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
stv0288 Register 42 bits 6 & 7 should be set to 0.
This is causing intermittent lock, the dvb-usb-lmedm04 driver uses
register 50 (auto fine mode) to correct for this, this register is
now returned to its default setting.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Seems like 'adap->fe' test for NULL was meant to be before we dereference
that pointer.
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Acked-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Tested-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Signed-off-by: Florian Mickler <florian@mickler.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Signed-off-by: Florian Mickler <florian@mickler.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Signed-off-by: Florian Mickler <florian@mickler.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note: This change is tested to compile only as I don't have the
hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we need a bigger buffer, we reallocte a new buffer and free the old
one.
Note: This change is tested to compile only as I don't have the
hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note: This change is tested to compile only as I don't have the
hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Otherwise it is not obvious that vp702x_usb_in_op or vp702x_usb_out_op
will not interfere with any vp702x_usb_inout_op.
Note: This change is tested to compile only, as I don't have the
hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This sets up a buffer and a mutex protecting that buffer in
the struct vp702x_device_state.
The definition of struct vp702x_device_state is moved into the header
in order to use the buffer also in the frontend.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need a state struct for the dvb_usb_device.
In order to reduce confusion we rename the vp702x_state struct.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some whitespace, one linebreak and one unneded variable
initialization...
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Igor M. Liplianin <liplianin@tut.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the on-stack buffers for USB DMA transfers.
This is an alternative version of the patch discussed by Florian here:
http://thread.gmane.org/gmane.linux.kernel/1115695/
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the newly introduced KEY_IMAGES where appropriate, and standardize
on KEY_MEDIA for media center/application launcher button (such as the
Windows logo key on the Windows Media Center Ed. remotes).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
