Adding control to clk_rx, and makes the control of clk_{rx|tx|tcp}
with safer sequence.
This sequence is provided by JMicron.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear Transmit Timer/Retry setting while full-duplex.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After main chip rev 5, the hardware support more power saving
control registers.
Some Non-Linux drivers might turn off the phy power with new
interfaces, this patch makes it possible for Linux to turn it
on again.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the main and sub chip revision for later workaround use.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two bugs introduced by the commit
c659c38b27 ("tlan: Code cleanup:
checkpatch.pl is relatively happy now.") In that change,
TLAN_CSTAT_READY was considered as a bit mask containing a single bit
set while it was actually had two set instead.
Many thanks to Dan Carpenter for finding the mistake.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->master is now tightly connected to bonding driver. This patch makes
this pointer more general and ready to be used by others.
- netdev_set_master() - bond specifics moved to new function
netdev_set_bond_master()
- introduced netif_is_bond_slave() to check if device is a bonding slave
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded depends on PHYLIB. The config selection is already in
an if PHYLIB / endif block.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
WOL is not supported for Vrtual Functions.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid accessing the hardware when UE is detected.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_cmd_pmac_add/del functions need to pass domain number to the firmware.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we are always using the Emulex OUI for a VF MAC address
while generating MAC for a VF. Use OUI from current MAC instead.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF needs to cleanup all the interface handles that it created for the VFs.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to avoid the completion processing for be_vf_eth_addr_config
to consume the link status notification before netdev_register.
Otherwise this causes the PF miss its first link status update.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While configuring QOS for VFs, the VF number should be translated
to domain number correctly.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The atl1 driver uses the legacy PCI power management, so it has to
do some PCI-specific things in its ->suspend() and ->resume()
callbacks, which isn't necessary and should better be done by the PCI
subsystem-level power management code.
Convert atl1 to the new PCI power management framework and make it
let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.
Tested-by: Thomas Fjellstrom <thomas@fjellstrom.ca>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The atl1c driver shouldn't call device_init_wakeup() in its probe
routine with the second argument equal to 1, because for PCI devices
the wakeup capability setting is initialized as appropriate by the
PCI subsystem. Remove the potentially harmful call.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver uses device_init_wakeup() in such a way that the
device's power.can_wakeup flag may be set even though the PCI
subsystem cleared it before, in which case the device cannot wake
up the system from sleep states. Modify the driver to only change
the power.can_wakeup flag if the device is not capable of generating
wakeup signals.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver does not show 100MB support in ethtool.
Adding support for the same.
Signed-off-by: Atita Shirwaikar <atita.shirwaikar@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function ixgbe_init_mbx_params_pf isn't used unless CONFIG_PCI_IOV
is defined. This is causing namespace warnings. So I wrapped its
definition in CONFIG_PCI_IOV too.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We had a support function that just walked a few pointers to get
from the ixgbe_hw struct to the netdev pointer. This was causing
a namespace warning so I removed it and just reference the pointers
directly.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We didn't need the prototype and it was causing namespace complaints so
I made it static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This consolidates hardware specifics to ixgbe_dcb.c this simplifies
code that was previously branching based on hardware type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This removes the RESET bit previously used to force a device
reset when DCB bandwidth configurations were changed. This can
now be done dynamically without a reset so the bit is no longer
needed. The only remaining operations that force a device reset
are DCB enable/disable and FCoE application priority changes.
DCB enable/disable is a hardware requirement.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82599 and 82598 devices do not require hardware resets to
configure CEE pg settings. This patch changes DCB configuration
to set the CEE pg values directly from the dcbnl ops routine.
This reduces the number of resets seen on the wire and allows
LLDP to reach a steady state faster.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implements 802.1Qaz support for ixgbe driver. Additionally,
this adds IEEE_8021QAZ_TSA_{} defines to dcbnl.h this is to
avoid having to use cryptic numeric codes for the TSA type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the routines that configure the HW for DCB require a
ixgbe_dcb_config structure. This structure was designed to support
the CEE standard and does not match the IEEE standard well.
This patch changes the HW routines in ixgbe_dcb_8259x.{ch} to use
raw pfc and bandwidth values. This requires some parsing of the DCB
configuration but makes the HW routines independent of the data
structure that contains the DCB configuration.
The primary advantage to doing this is we can do HW setup directly
from the 802.1Qaz ops without having to arbitrarily encapsulate this
data into the CEE structure.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove round robin configuration code for 82598 parts it
is not settable and is always false.
If we need/want this in the future we can add it back properly.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the FCoE priority is not changing do not set the RESET and
APP_UPCHG bits. This causes unneeded HW resets and which can
cause unneeded LLDP frames and negotiations.
The current check is not sufficient because the FCoE priority
can change twice during a negotiation which results in the
bits being set. This occurs when the switch changes the
priority or when the link is reset with switches that do not
include the APP priority until after PFC has been negotiated.
This results in set_app being called with the local APP
priority. Then the negotiation completes and set_app
is called again with the peer APP priority. The check
fails so the device is reset and the above occurs again
resulting in an endless loop of resets.
By only resetting the device if the APP priority has really
changed we short circuit the loop.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds full support for SR-IOV by enabling the PF side.
VF side has already been committed.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
...when invoked while interface is not up or when auto-negotiation is
disabled as done by other drivers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
*e1000_gstrings_test is not the same size as e1000_gstrings_test.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As a precautionary measure, expand the fix submitted in commit
4d163b75e9 entitled "tg3: Fix 5719 A0 tx
completion bug" to apply to all 5719 revisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in case reload pch_can,
pch_can not to be able to catch interrupt.
The cause is bus-master is not set in pch_can.
Thus, add enabling bus-master processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when rmmod pch_can, kernel failure occurs.
The cause is pci_iounmap executed before pch_can_reset.
Thus pci_iounmap moves after pch_can_reset.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, 800k comms fails since prop_seg set zero.
(EG20T PCH CAN register of prop_seg must be set more than 1)
To prevent prop_seg set to zero, change tseg2_min 1 to 2.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
