The purpose of this patch:
- Adopt the DMA API (jazzsonic, macsonic & core driver).
- Adopt the driver model (macsonic).
This part was cribbed from jazzsonic. As a consequence, macsonic once
again works as a module. Driver model is also used by the DMA calls.
- Support 16 bit cards (macsonic & core driver, also affects jazzsonic)
This code was adapted from the mac68k linux 2.2 kernel, where it has
languished for a long time.
- Support more 32-bit mac cards (macsonic)
Also from mac68k repo.
- Zero-copy buffer handling (core driver)
Provides a nice performance improvement. The new algorithm incidentally
helped to replace the old Jazz DMA code.
The patch was tested on a variety of macs (several 32-bit quadra built-in
NICs, a 16-bit LC PDS NIC and a 16-bit comm-slot NIC), and also on MIPS
Jazz.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] [NET] mv643xx: add workaround for HW checksum generation bug
The hardware checksum generator on the mv64xxx occasionally generates
an incorrect checksum. This patch works around the issue and enables
hardware checksum generation.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Patch Description:
This patch incorporates the following hardware fixes required
for Xframe II adapter.
1. New values to program the dtx_control register.
2. Disable memory controller interrupts(MC_INTR) since these
are now monitored thru' a poll routine.
3. Don't reset an XframeII card on an ECC double-bit error(It
can recover).
4. Save/restore PCI config space before/after a reset irrespective
of Xframe I or II card.
5. Bumped up the driver version no. to 2.0.3.1
Please review the patch and apply the same if it looks ok.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Now that all tms380 devices have a valid
struct device with dma_mask, remove dmalimit from tmsdev_init().
Kconfig: depend tms380tr and madgemc on MCA.
abyss.c, proteon.c, skisa.c, tmspci.c, tms380tr.h:
remove dmalimit parameter from tmsdev_init().
tms380tr.c: use device->dma_mask instead of dmalimit.
madgemc.c: move to new MCA API using struct device.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/e1000/e1000_main.c: In function `e1000_clean_tx_irq':
drivers/net/e1000/e1000_main.c:2774: warning: size_t format, dma_addr_t arg (arg 8)
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The multicast code of the fmvj18x_cs driver is broken.
I fixed it to work properly.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The Linksys EG1032 uses Realtek's 8169 chipset.
Credit goes to Bob Wilson <bwilson4web@hotmail.com> for the report.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use msleep_interruptible() instead of delay_cycx() to guarantee the task
delays as expected. Remove the prototype and definition of delay_cycx().
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Rüdiger found a bug in nv_open that explains some of the reports
with duplex mismatches:
nv_open calls nv_update_link_speed for initializing the hardware link speed
registers. If current link setting matches the values in np->linkspeed and
np->duplex, then the function does nothing.
Usually, doing nothing is the right thing, but not in nv_open: During
nv_open, the registers must be initialized because the nic was reset.
The attached patch fixes that by setting np->linkspeed to an invalid value
before calling nv_update_link_speed from nv_open.
Signed-Off-By: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The DM9000 driver is responding to ioctl() calls it should not be. This
can cause problems with the wireless tools incorrectly indentifying the
device as wireless capable, and crashing under certain operations.
This patch also moves the version printk() to the init call, so that
you only get it once for multiple devices, and to show it is loaded
if there are no defined dm9000s
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix DM9000 driver usage of spinlocks, which mainly came to light
when running a kernel with spinlock debugging. These come down to:
1) Un-initialised spin lock
2) Several cases of using spin_xxx(lock) and not spin_xxx(&lock)
3) move the locking around the phy reg for read/write to only
keep the lock when actually reading or writing to the phy.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
After suspend the driver needs to retest link status in case the cable
has been inserted or removed during the suspend.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Using the right register clearly improves chances of getting the MII
code and thus the driver working at all.
- On startup check the media type before setting up duplex or we might
spend the first 1.2s with a wrong duplex setting.
- Get rid of whitespace lines.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The flush threshold in the MAC chip should be increased.
Found while reviewing vendor version of sk98lin driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some versions of the Marvell yukon generate bogus sensor warning interrupts.
The driver would flood log with these messages. Handle this situation
cleanly by masking away at boot time.
Fixes: http://bugs.gentoo.org/show_bug.cgi?id=87182
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
drivers/net/skge.c | 24 ++++++++++--------------
drivers/net/skge.h | 8 ++++++--
2 files changed, 16 insertions(+), 16 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Suggested by Steven Rostedt, matches his patch included in e100.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefined buffer_info-dma to be dma_addr_t instead of uint64
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove unused functions, render some variable static instead of global - based on patch from Adrian Bunk
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Ethtool cleanup patch from Stephen Hemminger
* use ADVERTISED_xxx fields when setting advertised fields
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix data output by ethtool -d
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use netdev_priv() instead of netdev->priv
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix unnecessary link state messages
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Set RXDCTL:PTHRESH/HTHRESH to zero
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This is a patch to incorporate comments from earlier 12 patches.
It also fixes a few issues we found during this time.
Following is a list of changes in this patch. Item 1 incorporates
earlier comments. Issues addressed in items 2 to 4 were discovered
recently.
1. wmb() call in s2io_xmit() replaced with mmiowb().
2. The dtx_control register was earlier programmed incorrectly
for Xframe II adapter.
3. As suggested by hardware team, after a reset, in case of
Xframe II adapter, we clear certain spurious errors by
clearing PCI-X ECC status register, "detected parity error"
bit in PCI_STATUS register and PCI_STATUS bit in txpic_int register.
4. On IBM PPC platforms, we found that in the Rx buffer replenish
function, two memory writes(one to the the descriptor length and
another to the ownership) were getting reordered. This was causing
the adapter to see the ownership transfered to it before the length
was updated.
One solution was to add a wmb() but since this would turnout expensive
on some platforms if called for every descriptor, we set the ownership
bit and other fields of '2' to 'N' Rx descriptors followed by a wmb()
and then set the ownership of first descriptor ('1').
Here the value 'N' is configurable by making it a module loadable
parameter (rxsync_frequency).
(NOTE: This parameter is a power of 2).
5. Bumped up the driver version no. to 2.0.2.1
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
The last patch in this series fixes the following issues found during
testing.
1. Ensure we don't pass zero sized buffers to the card(which can lockup)
2. Restore the PCI-X parameters(in case of Xframe I adapter) after a reset.
3. Make sure total size of all FIFOs does not exceed 8192.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
The below patch implements a new "Link state change handling"
scheme supported by the Xframe II adapter. It also bumps up the
driver version to 2.0.2.0.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This is a patch to provide bimodal interrupt moderation support for
Xframe II adapter. Basically, in this moderation scheme, the adapter
raises a traffic interrupt if the no. of packets transmitted and/or
received reaches a programmable threshold.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch provides basic support for the Xframe II adapter.
Includes the following changes:
1. New values to program XAUI interface.
2. Print the PCI/PCI-X mode(bus frequency, width).
3. Remove EOI from reset during intialization.
4. Enable all 8 PCCs if Xframe II adapter.
5. Programs the RLDRAM size depending on the device.
(Note: RLDRAM size on XFARME-I is 64Mb whereas on XFRAME-II it's 32 Mb).
6. Enable extended(64-bit) statistics counters.
7. Program timer interrupt duration based on PCI/PCI-X clock speed.
8. Not required to save/restore PCI config space before/after reset.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch implements the slow-path handling functions(link
state change, hardware errors) as a timer. It is not
handled in interrupt handler as was done previously.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch relates to mostly performance related changes.
1. Fixed incorrect computation of PANIC level in rx_buffer_level().
2. Removed unnecessary PIOs(read/write of tx_traffic_int and
rx_traffic_int) from interrupt handler and removed read of
general_int_status register from xmit routine.
3. Enable two-buffer mode(for Rx path) automatically for SGI
systems. This improves Rx performance dramatically on
SGI systems.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch fixes certain memory leaks discovered in free_tx_buffers()
and rx_osm_handler()
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below patch includes fixes for few purely software bugs identified
since last release.
1. Keep track and display(as part of ethtool command output) the no.
of single-bit and double-bit ECC errors.
2. Handle race condition between intr handler and "interface down"
routine.
3. Initial link state setting modified so that the link state displayed
after "interface Up" is correct.
4. Fix for "Incorrect Tx packet count when TSO is enabled".
5. Disable periodic DMA of statistics and schedule one-shot DMA
only when required.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below patch addresses few h/w specific issues.
1. Check for additional ownership bit on Rx path before
starting Rx processing.
2. Enable only 4 PCCs(Per Context Controller) for Xframe I
revisions less than 4.
3. Program Rx and Tx round robin registers depending on
no. of rings/FIFOs.
4. Tx continous interrupts is now a loadable parameter.
5. Reset the card if we get double-bit ECC errors.
6. A soft reset of XGXS being done to force a link state change has been
eliminated.
7. After a reset, clear "parity error detected" bit,
PCI-X ECC status register, and PCI_STATUS bit in
tx_pic_int register.
8. The error in the disabling allmulticast implementation has been
rectified.
9. Leave the PCI-X parameters MMRBC, OST etc. at their
BIOS/system defaults.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
We are submitting a series of 13 patches to support our Xframe I and
Xframe II line of products. The patches can be categorized as follows:
Patches 1-8 : Changes applicable to both Xframe I and II
Patches 9-11: Xframe II specific features
Patch 12: Addresses issues found during testing cycle.
Patch 13: Incorpoates mostly the review comments from community
and some last moment bug fixes.
Please review the patches and let us know your comments.
Starting with patch 1 below.
This patch involves cosmetic changes(tabs and indentation,
regrouping of transmit and receive data structures, typecasting,
code cleanup).
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix the p-persistence CSMA algorithm which in simplex mode was starting
with a slottime delay before doing anything else as if there was carrier
collision resulting in bad performance on simplex links.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
