The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"The main change is support for keyboards and touchpads found in 2015
editions of Macbooks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: zforce - don't overwrite the stack"
Input: bcm5974 - add support for the 2015 Macbook Pro
HID: apple: Add support for the 2015 Macbook Pro
Input: bcm5974 - prepare for a new trackpad generation
Input: synaptics - dump ext10 capabilities as well
This reverts commit 7d01cd261c because
with given FRAME_MAXSIZE of 257 the check will never trigger and it
causes warnings from GCC (with -Wtype-limits). Also the check was
incorrect as it was not accounting for the already read 2 bytes of data
stored in the buffer.
The GPIOD API can be used from boardcode, so that the DT check can be
removed. To avoid breaking existing boardcode, _optional() variant has been
chosen. For completely removing the DT check, the regulator has also been
made optional, so that it could be supplied from boardcode.
As a side-effect the patch fixes the after-probe reset GPIO state, so that
the device is not kept in reset state.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using dev_*_drvdata() instead of spi_*_drvdata() reduces lines of code and
prepares the driver for possible tsc2004 support, which is i2c based.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert driver so that it uses regmap instead of directly using
spi_transfer for all register accesses.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace spaces with tab, so that the tsc2005 Kconfig entry matches the
other entries in drivers/input/touchscreen/Kconfig.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Improve defines for first control byte by removing 0x00 prefix (the defines
are for 8 bit values and not for 16 bit values) and expose register
structure by exposing the shift.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the MacBookPro12,1 model. This patch needs to be
applied together with the accompanied HID patch, as usual.
Tested-by: John Horan <knasher@gmail.com>
Tested-by: Jochen Radmacher <jradmacher@gmx.de>
Tested-by: Yang Hongyang <burnef@gmail.com>
Tested-by: Yen-Chin, Lee <coldnew.tw@gmail.com>
Tested-by: George Hilios <ghilios@gmail.com>
Tested-by: Janez Urevc <janez@janezurevc.name>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With the advent of the Macbook Pro 12, we see a new generation of
trackpads, capable of force sensoring and haptic feedback.
This patch prepares for the new device by adding configuration data
for the code paths that would otherwise look different.
Tested-by: John Horan <knasher@gmail.com>
Tested-by: Jochen Radmacher <jradmacher@gmx.de>
Tested-by: Yang Hongyang <burnef@gmail.com>
Tested-by: Yen-Chin, Lee <coldnew.tw@gmail.com>
Tested-by: George Hilios <ghilios@gmail.com>
Tested-by: Janez Urevc <janez@janezurevc.name>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make extended capabilities obtained through $10 query also available in
touchpad identification.
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fix for the warnings/oops when handling HID devices with "unnamed"
LEDs and couple of other driver fixups""
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: goodix - fix touch coordinates on WinBook TW100 and TW700
Input: LEDs - skip unnamed LEDs
Input: usbtouchscreen - avoid unresponsive TSC-30 touch screen
Input: elantech - force resolution of 31 u/mm
Input: zforce - don't overwrite the stack
The touchscreen on the WinBook TW100 and TW700 don't match the default
display, with 0,0 touches being reported when touching at the bottom
right of the screen.
1280,800 0,800
+-------------+
| |
| |
| |
+-------------+
1280,0 0,0
It's unfortunately impossible to detect this problem with data from the
DSDT, or other auxiliary metadata, so fallback to quirking this specific
model of tablet instead.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Devices may declare more LEDs than what is known to input-leds
(HID does this for some devices). Instead of showing ugly warnings
on connect and, even worse, oopsing on disconnect, let's simply
ignore LEDs that are not known to us.
Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add CYTP0002 to the list of ACPI HIDs recognized by the driver.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the the runtime suspend power management not working issue when system
starts up and before user touches the trackpad device.
TEST=test on Chromebook.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Gen5 and Gen6 trackpad devices are able to detect and report object
proximity data/events, add this function support in the cyapa driver
through the ABS_DISTANCE event.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on the cyapa core, add support for basic functionality of the gen6
trackpad devices. The driver can automatically determine what protocol
(gen3, gen5, or gen6) should be used with the attached trackpad device.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change 'gen5' to 'pip' for all macros, variables and functions that are
shared between gen5 and gen6 modules to make naming more clear and
readable.
Also fix a few spelling errors.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On pm8xxx PMICs, shutdown and restart are signaled to the PMIC via a pin
called PS_HOLD. When this pin goes low, the PMIC performs a configurable
power sequence. Add a .shutdown hook so that we can properly configure this
power sequence for shutdown or restart depending on the system state.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30
touch screen. Due to a missing delay between the RESET and SET_RATE
commands, the touch screen may become unresponsive during system startup or
driver loading.
According to the DMC documentation, a delay is needed after the RESET
command to allow the chip to complete its internal initialization. As this
delay is not guaranteed, we had a system where the touch screen
occasionally did not send any touch data. There was no other indication of
the problem.
The patch fixes the problem by adding a 150ms delay between the RESET and
SET_RATE commands.
Cc: stable@vger.kernel.org
Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com>
Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVrBp0AAoJEHm+PkMAQRiGADsH/iCVjA1x+a19xpeuHNJcjcQR
Lin8td8zdUxereBNQOFjnkhCmKtzLODXGkQdYFaWZx8mbEQ93wC+nPV8O+LsqPbI
T/2MjJ78IjlNsoTyE4b1AhqpASsxrLZJNB+f9dd251f1BSAzKfRER0G46WxbOPN7
9HdzCMbtx03ZJkr9baE6alljxA43O5mpDzpotKIagfTMQr5h0ra16uXlmVXFjHRs
roNJsugwKxJPnVmLWWOM1JsAjRSMBAXQUQxhJJCMDOhgZZ5KR1z6L30ESeFTUhvh
WG/2MEfyVYXn91kV0N+AUCuOFHTv6uiaz3RaRVJFDSv3sPOh1WQ9tQHxyrBsqyY=
=MA/P
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rc3' into next
Sync up with Linux 4.2-rc3 to bring in infrastructure (OF) pieces.
ELAN0600 seems to work just fine in mouse emulation mode through i2c-hid,
but to have full raw touch support we need to register it in elan_i2c.ko
Reported-and-tested-by: Alessio Treglia <alessio@debian.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 2d53809594 ("Input: zforce_ts - convert to use the gpiod
interface") converted this driver to use the gpiod functions. These
functions take the active low property into account, so we don't have
to invert the result of gpiod_get_value_cansleep(). This has been
missed in that commit. Fix it.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of inventing a new property name, let's use "wakeup-source" to
be consistent with other driver and subsystem bindings.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Separate the functionality using sequences of register writes from the
functions that take register defaults. This change renames the arguments
in order to support the extension of reg_sequence to take an optional
delay to be applied after any given register in a sequence is written.
This avoids adding an int to all register defaults, which could
substantially increase memory usage for regmaps with large default tables.
This also updates all the clients of multi_reg_write/register_patch.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to the same definition of state container as in MAX77693 drivers.
This will allow usage of one regulator driver in both devices: MAX77693
and MAX77843.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This prepares for merging some of the drivers between max77693 and
max77843 so the child MFD driver can be attached to any parent MFD main
driver.
Move the state container to common header file. Additionally add
consistent 'i2c' prefixes to its members (of 'struct i2c_client' type).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All Elantech touchpads pre-v4 with dynamic resolution queries have a fixed
resolution of 800dpi -> 31.49 units/mm. Set this statically, so userspace
does not have to guess.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If we get a corrupted packet with PAYLOAD_LENGTH > FRAME_MAXSIZE, we
will silently overwrite the stack.
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <external.Oleksij.Rempel@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The legacy system PM support has long time ago been dropped from the
AMBA bus. Align to that by converting to the modern system PM
callbacks.
Fixes: 26825cfd90 (ARM: 7914/1: amba: Drop legacy PM support ...)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A big problem with the current i8042 debugging option is that it outputs
data going to and from the keyboard by default. As a result, many dmesg
logs uploaded by users will unintentionally contain sensitive information
such as their password, as such it's probably a good idea not to output
data coming from the keyboard unless specifically enabled by the user.
Signed-off-by: Stephen Chandler Paul <cpaul@redhat.com>
Reviewed-by: Andreas Mohr <andim2@users.sf.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
add snvs power key driver.
It work in imx chips after i.mx6sx
ON/OFF key used power on/off whole system.
This driver make it wakeup from suspend state when short press
ON/OFF key.
Long time press will trig SNVS power off chip without software
intervention.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The original wait time was 200ms which was enough for the firmware to
finish loading and boot. After that the firmware will perform
initialization and touch calibration, which will take about 1.1 second. The
touch calibration will change controller frequency to scan at the most
optimal frequency and during calibration/frequency switching process we may
run into i2c data errors. To avoid them we extend the sleep to 2500ms after
issuing the sw reset.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These attributes can be used to identify controllers present in the system.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch to using standard touchscreen device properties parsing module
instead of doing it by hand in the driver.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() will perform necessary settings for performing
multi-touch to single-touch emulation, we do not need to do that ourselves.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The controller has a RESET pin which is usually controlled over
a GPIO line. If such a GPIO is provided, perform a RESET
during probe.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are using threaded interrupt handler and thus are allowed to sleep.
Let's switch over to gpiod_get_value_cansleep() so that we do not get
ugly warnings in case GPIO controller might sleep when accessing GPIO.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This allows uniform parsing on legacy, DT and ACPI systems.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's move driver's platform data definitions from include/linux/input/
into include/linux/platform_data/ so that it stays with the rest of
platform data definitions.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
