Here's the big tty/serial driver patchset for 3.18-rc1.
Lots of little things in here, some good work from Peter Hurley on the
tty core, and in lots of drivers. There are also lots of other driver
updates in here as well, full details in the changelog below.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQ0aDwACgkQMUfUDdst+ymueACeI1i2exlGaBBSVQuUK2Jmx8Uz
nukAn3KPuvvx+MKfMMBRpK0DQCzTxv4P
=dwv1
-----END PGP SIGNATURE-----
Merge tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver patchset for 3.18-rc1.
Lots of little things in here, some good work from Peter Hurley on the
tty core, and in lots of drivers. There are also lots of other driver
updates in here as well, full details in the changelogs.
All have been in the linux-next tree for a while"
* tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (99 commits)
Revert "serial/core: Initialize the console pm state"
tty: serial: 8250: use 32bit variable for rpm_tx_active
tty: serial: msm: Add earlycon support
serial/core: Initialize the console pm state
serial: asc: Conditionally use readl_relaxed (COMPILE_TEST)
serial: of-serial: add PM suspend/resume support
m68k: AMIGA_BUILTIN_SERIAL should depend on TTY
asm/uapi: Add definition of TIOC[SG]RS485
tty/metag_da: Add console_poll module parameter
serial: 8250_pci: remove rts_n override from Baytrail quirk
serial: cadence: Add generic earlycon support
serial: imx: change the wait even to interruptiable
serial: imx: terminate the RX DMA when the UART is suspending
serial: imx: fix throttle/unthrottle callbacks for hardware assisted flow control
serial: 8250: Add Quark X1000 to 8250_pci.c
tty: omap-serial: pull out calculation from baud_is_mode16
tty: omap-serial: fix division by zero
xen_hvc: no reason to write the type key on xenstore
tty: serial: 8250_core: remove UART_IER_RDI in serial8250_stop_rx()
tty: serial: 8250_core: use the ->line argument as a hint in serial8250_find_match_or_unused()
...
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids fuse hangs on sh4 by flushing the cache on
get_user_pages_fast(). This is not necessary a good thing to do, but
get_user_pages() does this, so get_user_pages_fast() should too.
Please note the patch for mips arch that addresses the similar problem:
https://kernel.googlesource.com/pub/scm/linux/kernel/git/ralf/linux/+/linux-3.4.50%5E!/#F0
They basically simply disable get_user_pages_fast() at all, using a
fall-back to get_user_pages(). But my fix is different, it adds an
explicit cache flushes.
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit: e676253b19 (serial/8250: Add
support for RS485 IOCTLs), adds support for RS485 ioctls for 825_core on
all the archs. Unfortunaltely the definition of TIOCSRS485 and
TIOCGRS485 was missing on the ioctls.h file
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New system call depends on crypto. As it did not have a separate config
option, CONFIG_KEXEC was modified to select CRYPTO and CRYPTO_SHA256.
But now previous patch introduced a new config option for new syscall.
So CONFIG_KEXEC does not require crypto. Remove that dependency.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the sh-intc driver is compiled on all SuperH and
non-multiplatform SH-Mobile platforms, while it's only used on a limited
number of platforms:
- SuperH: SH2(A), SH3(A), SH4(A)(L) (all but SH5)
- ARM: sh7372, sh73a0
Drop the "default y" on SH_INTC, make all CPU platforms that use it
select it, and protect all sub-options by "if SH_INTC" to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull slave-dma updates from Vinod Koul:
"Some notable changes are:
- new driver for AMBA AXI NBPF by Guennadi
- new driver for sun6i controller by Maxime
- pl330 drivers fixes from Lar's
- sh-dma updates and fixes from Laurent, Geert and Kuninori
- Documentation updates from Geert
- drivers fixes and updates spread over dw, edma, freescale, mpc512x
etc.."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (72 commits)
dmaengine: sun6i: depends on RESET_CONTROLLER
dma: at_hdmac: fix invalid remaining bytes detection
dmaengine: nbpfaxi: don't build this driver where it cannot be used
dmaengine: nbpf_error_get_channel() can be static
dma: pl08x: Use correct specifier for size_t values
dmaengine: Remove the context argument to the prep_dma_cyclic operation
dmaengine: nbpfaxi: convert to tasklet
dmaengine: nbpfaxi: fix a theoretical race
dmaengine: add a driver for AMBA AXI NBPF DMAC IP cores
dmaengine: add device tree binding documentation for the nbpfaxi driver
dmaengine: edma: Do not register second device when booted with DT
dmaengine: edma: Do not change the error code returned from edma_alloc_slot
dmaengine: rcar-dmac: Add device tree bindings documentation
dmaengine: shdma: Allocate cyclic sg list dynamically
dmaengine: shdma: Make channel filter ignore unrelated devices
dmaengine: sh: Rework Kconfig and Makefile
dmaengine: sun6i: Fix memory leaks
dmaengine: sun6i: Free the interrupt before killing the tasklet
dmaengine: sun6i: Remove switch statement from buswidth convertion routine
dmaengine: of: kconfig: select DMA_ENGINE when DMA_OF is selected
...
Pull arch signal handling cleanup from Richard Weinberger:
"This patch series moves all remaining archs to the get_signal(),
signal_setup_done() and sigsp() functions.
Currently these archs use open coded variants of the said functions.
Further, unused parameters get removed from get_signal_to_deliver(),
tracehook_signal_handler() and signal_delivered().
At the end of the day we save around 500 lines of code."
* 'signal-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (43 commits)
powerpc: Use sigsp()
openrisc: Use sigsp()
mn10300: Use sigsp()
mips: Use sigsp()
microblaze: Use sigsp()
metag: Use sigsp()
m68k: Use sigsp()
m32r: Use sigsp()
hexagon: Use sigsp()
frv: Use sigsp()
cris: Use sigsp()
c6x: Use sigsp()
blackfin: Use sigsp()
avr32: Use sigsp()
arm64: Use sigsp()
arc: Use sigsp()
sas_ss_flags: Remove nested ternary if
Rip out get_signal_to_deliver()
Clean up signal_delivered()
tracehook_signal_handler: Remove sig, info, ka and regs
...
Load purgatory code in RAM and relocate it based on the location.
Relocation code has been inspired by module relocation code and purgatory
relocation code in kexec-tools.
Also compute the checksums of loaded kexec segments and store them in
purgatory.
Arch independent code provides this functionality so that arch dependent
bootloaders can make use of it.
Helper functions are provided to get/set symbol values in purgatory which
are used by bootloaders later to set things like stack and entry point of
second kernel etc.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The core mm code will provide a default gate area based on
FIXADDR_USER_START and FIXADDR_USER_END if
!defined(__HAVE_ARCH_GATE_AREA) && defined(AT_SYSINFO_EHDR).
This default is only useful for ia64. arm64, ppc, s390, sh, tile, 64-bit
UML, and x86_32 have their own code just to disable it. arm, 32-bit UML,
and x86_64 have gate areas, but they have their own implementations.
This gets rid of the default and moves the code into ia64.
This should save some code on architectures without a gate area: it's now
possible to inline the gate_area functions in the default case.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> [in principle]
Acked-by: Richard Weinberger <richard@nod.at> [for um]
Acked-by: Will Deacon <will.deacon@arm.com> [for arm64]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Nathan Lynch <Nathan_Lynch@mentor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge incoming from Andrew Morton:
- Various misc things.
- arch/sh updates.
- Part of ocfs2. Review is slow.
- Slab updates.
- Most of -mm.
- printk updates.
- lib/ updates.
- checkpatch updates.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (226 commits)
checkpatch: update $declaration_macros, add uninitialized_var
checkpatch: warn on missing spaces in broken up quoted
checkpatch: fix false positives for --strict "space after cast" test
checkpatch: fix false positive MISSING_BREAK warnings with --file
checkpatch: add test for native c90 types in unusual order
checkpatch: add signed generic types
checkpatch: add short int to c variable types
checkpatch: add for_each tests to indentation and brace tests
checkpatch: fix brace style misuses of else and while
checkpatch: add --fix option for a couple OPEN_BRACE misuses
checkpatch: use the correct indentation for which()
checkpatch: add fix_insert_line and fix_delete_line helpers
checkpatch: add ability to insert and delete lines to patch/file
checkpatch: add an index variable for fixed lines
checkpatch: warn on break after goto or return with same tab indentation
checkpatch: emit a warning on file add/move/delete
checkpatch: add test for commit id formatting style in commit log
checkpatch: emit fewer kmalloc_array/kcalloc conversion warnings
checkpatch: improve "no space after cast" test
checkpatch: allow multiple const * types
...
Pull trivial tree changes from Jiri Kosina:
"Summer edition of trivial tree updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: fix two typos in watchdog-api.txt
irq-gic: remove file name from heading comment
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
doc: replace "practise" with "practice" in Documentation
befs: remove check for CONFIG_BEFS_RW
scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
drivers/usb/phy/phy.c: remove a leading space
mfd: fix comment
cpuidle: fix comment
doc: hpfall.c: fix missing null-terminate after strncpy call
usb: doc: hotplug.txt code typos
kbuild: fix comment in Makefile.modinst
SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
ARM: msm: Remove MSM_SCM
crypto: Remove MPILIB_EXTRA
doc: CN: remove dead link, kerneltrap.org no longer works
media: update reference, kerneltrap.org no longer works
hexagon: update reference, kerneltrap.org no longer works
doc: LSM: update reference, kerneltrap.org no longer works
...
This patch set consists of the usual driver updates (ufs, storvsc, pm8001
hpsa). It also has removal of the user space target driver code (everyone is
using LIO now), a partial PCI MSI-X update, more multi-queue updates,
conversion to 64 bit LUNs (so we could theoretically cope with any LUN
returned by a device) and placeholder support for the ZBC device type (Shingle
drives), plus an assortment of minor updates and bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT4mS9AAoJEDeqqVYsXL0Mq34H/2AeXiM8GEVO3PIsBtF3TFZ9
poJvAyb8t//+VwAIVLHU9wrssIrIcyvNQmNHH/InGt5rOaXwGQRsnEc73bBtot4b
aC1t+hAnp2Ddvu6phmyUg7iY2GmQhAoZmeaj7krGIu2XgtLGiPg26eSsgk4Yv/U9
cuULEuOc/UnTj3w5VK8SvpyXMybVF6oQhSrS1slOglfFwPTlTI/NHU9xo7Wc3qHT
VifHXNphIvye5EH8zwtKX5p8qCrFW0pevJwyfPz7Hp2CTA9XYKx3SoeOh+n9F9ez
udBBggg7Vb1tb4mPKUoZ78UrtCVdFSCmesBU/RJe7cIh8daKaO5MVr3WPSx2JhM=
=yGai
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (ufs, storvsc,
pm8001 hpsa). It also has removal of the user space target driver
code (everyone is using LIO now), a partial PCI MSI-X update, more
multi-queue updates, conversion to 64 bit LUNs (so we could
theoretically cope with any LUN returned by a device) and placeholder
support for the ZBC device type (Shingle drives), plus an assortment
of minor updates and bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (143 commits)
scsi: do not issue SCSI RSOC command to Promise Vtrak E610f
vmw_pvscsi: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Fix invalid return when request_irq() failed
lpfc: Remove superfluous call to pci_disable_msix()
isci: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Cleanup bfad_setup_intr() function
bfa: Do not call pci_enable_msix() after it failed once
fnic: Use pci_enable_msix_exact() instead of pci_enable_msix()
scsi: use short driver name for per-driver cmd slab caches
scsi_debug: support scsi-mq, queues and locks
Drivers: add blist flags
scsi: ufs: fix endianness sparse warnings
scsi: ufs: make undeclared functions static
bnx2i: Update driver version to 2.7.10.1
pm8001: fix a memory leak in nvmd_resp
pm8001: fix update_flash
pm8001: fix a memory leak in flash_update
pm8001: Cleaning up uninitialized variables
pm8001: Fix to remove null pointer checks that could never happen
...
There've been many updates in ASoC side at this time, especially the
framework enhancement for multiple CODECs on a single DAI and more
componentization works. The only major change in ALSA core is the
addition of timestamp type in sw_params field. This should behave in
backward compatible way. Other than that, there are lots of small
changes and new drivers in wide range, including a large code cut in
HD-audio driver for deprecated static quirks. Some highlights are
below:
ALSA Core:
- Add the new timestamp type field to sw_params to choose
MONOTONIC_RAW type
HD-audio:
- Continued conversion to standard printk macros, generic code
cleanups
- Removal of obsoleted static quirk codes for Conexant and C-Media
codecs
- Fixups for HP Envy TS, Dell XPS 15, HP and Dell mute/mic LED,
Gigabyte BXBT-2807 mobo
- Intel Braswell support
ASoC:
- Support for multiple CODECs attached to a single DAI, enabling
systems with for example multiple DAC/speaker drivers on a single
link, contributed by Benoit Cousson based on work from Misael Lopez
Cruz
- Support for byte controls larger than 256 bytes based on the use of
TLVs contributed by Omair Mohammed Abdullah
- More componentisation work from Lars-Peter Clausen
- The remainder of the conversions of CODEC drivers to params_width()
by Mark Brown
- Drivers for Cirrus Logic CS4265, Freescale i.MX ASRC blocks, Realtek
RT286 and RT5670, Rockchip RK3xxx I2S controllers and Texas
Instruments TAS2552
- Lots of updates and fixes, especially to the DaVinci, Intel,
Freescale, Realtek, and rcar drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJT4fj0AAoJEGwxgFQ9KSmkXQ0QAIiRmVg40aiJoEdOLGgzNZtq
r/nXj69AuB6JSy0hKbFyyijjCcRpyCCGvjDYlogjT75M3c35Npz/m85oZHx2tajD
SB5OA+QxO4EQ3C0GjITIRHJROm4MM8/rnbnNYTsWnEGRkobTFTl0rHbSkA85RGFt
0zZqqs1R0s/nO9PMQ+5PA5x9xVFiZs2COeCK0CFA9s2ACf/hbxJBRIqYpIFWOo78
9L41jBOFuC/hIb4qwjgmsCWbKe1KQysTAf+Wty0CKipJ6VhfCbPn1Qn1zXGeUOxc
mj4eZ6LpJTrVMr/UN02c5vgPOiaBrQ7fWZo3dVHLlIjC6cEI1tUvNYAin7CMEzx8
DUsvo9p30OheA+ijc9wKaYFY6YmmJZRtpnnMd39i0oPG+bhvoV7vjXjJSB1sLJt1
o82xLpVL4Th8H+DMDVwA7UIBvvZGZBusw1qsNGfcOPrmExi4ScGhA0gSOO6W2y1z
VQLRbiXB/HtJGxeqWL6RqJOcLBOlJNmsk4UZMOSCu2OZrWd5I8MuRrNWeHDqhX1H
+VDEJVhFmM21vMpnobzEPxWsMgTVIAVf3Thh+WgaPxL4Krh0vkpZsgZk16VVmy/o
OJJF3n41FND4n9zSjOe4MkuL8UCOUpKCaBdqj9K1s6UKwOEKuDNslyT/zqutRWK5
x1uApU5y+E4iQT/b7cmA
=RL72
-----END PGP SIGNATURE-----
Merge tag 'sound-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There've been many updates in ASoC side at this time, especially the
framework enhancement for multiple CODECs on a single DAI and more
componentization works.
The only major change in ALSA core is the addition of timestamp type
in sw_params field. This should behave in backward compatible way.
Other than that, there are lots of small changes and new drivers in
wide range, including a large code cut in HD-audio driver for
deprecated static quirks. Some highlights are below:
ALSA Core:
- Add the new timestamp type field to sw_params to choose
MONOTONIC_RAW type
HD-audio:
- Continued conversion to standard printk macros, generic code
cleanups
- Removal of obsoleted static quirk codes for Conexant and C-Media
codecs
- Fixups for HP Envy TS, Dell XPS 15, HP and Dell mute/mic LED,
Gigabyte BXBT-2807 mobo
- Intel Braswell support
ASoC:
- Support for multiple CODECs attached to a single DAI, enabling
systems with for example multiple DAC/speaker drivers on a single
link, contributed by Benoit Cousson based on work from Misael Lopez
Cruz
- Support for byte controls larger than 256 bytes based on the use of
TLVs contributed by Omair Mohammed Abdullah
- More componentisation work from Lars-Peter Clausen
- The remainder of the conversions of CODEC drivers to params_width()
by Mark Brown
- Drivers for Cirrus Logic CS4265, Freescale i.MX ASRC blocks,
Realtek RT286 and RT5670, Rockchip RK3xxx I2S controllers and Texas
Instruments TAS2552
- Lots of updates and fixes, especially to the DaVinci, Intel,
Freescale, Realtek, and rcar drivers"
* tag 'sound-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (402 commits)
ALSA: usb-audio: Whitespace cleanups for sound/usb/midi.*
ALSA: usb-audio: Respond to suspend and resume callbacks for MIDI input
sound/oss/pss: Remove typedefs pss_mixerdata and pss_confdata
sound/oss/opl3: Remove typedef opl_devinfo
ALSA: fireworks: fix specifiers in format strings for propper output
ASoC: imx-audmux: Use uintptr_t for port numbers
ASoC: davinci: Enable menuconfig entry for McASP
ASoC: fsl_asrc: Don't access members of config before checking it
ASoC: fsl_sarc_dma: Check pair before using it
ASoC: adau1977: Fix truncation warning on 64 bit architectures
ALSA: virtuoso: add Xonar Essence STX II support
ALSA: riptide: fix %d confusingly prefixed with 0x in format strings
ALSA: fireworks: fix %d confusingly prefixed with 0x in format strings
ALSA: hda - add codec ID for Braswell display audio codec
ALSA: hda - add PCI IDs for Intel Braswell
ALSA: usb-audio: Adjust Gamecom 780 volume level
ALSA: usb-audio: improve dmesg source grepability
ASoC: rt5670: Fix duplicate const warnings
ASoC: rt5670: Staticise non-exported symbols
ASoC: Intel: update stream only on stream IPC msgs
...
This patch introduces zone_for_memory() to arch_add_memory() on sh to
ensure new, higher memory added into ZONE_MOVABLE if movable zone has
already setup.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Mel Gorman" <mgorman@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix build error as reported by Geert Uytterhoeven here:
http://kisskb.ellerman.id.au/kisskb/buildresult/11607865/
The error happens when CONFIG_HAS_IOPORT_MAP=n because of which there
are missing definitions of ioport_map/unmap(). Fix this build error by
adding these prototypes.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <stable@vger.kernel.org> [3.16+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the device name for the CMT.
Add clocks called usb0 and usb1 so that r8a66597_hcd works again on the
ecovec24 board
Signed-off-by: Daniel Palmer <danieruru@gmail.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The symbol is an orphan, get rid of it.
Submitted by Richard a few months ago as "[PATCH 21/28] Remove
CPU_SUBTYPE_SH7764".
[pebolle@tiscali.nl: re-added dropped ||]
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull perf changes from Ingo Molnar:
"Kernel side changes:
- Consolidate the PMU interrupt-disabled code amongst architectures
(Vince Weaver)
- misc fixes
Tooling changes (new features, user visible changes):
- Add support for pagefault tracing in 'trace', please see multiple
examples in the changeset messages (Stanislav Fomichev).
- Add pagefault statistics in 'trace' (Stanislav Fomichev)
- Add header for columns in 'top' and 'report' TUI browsers (Jiri
Olsa)
- Add pagefault statistics in 'trace' (Stanislav Fomichev)
- Add IO mode into timechart command (Stanislav Fomichev)
- Fallback to syscalls:* when raw_syscalls:* is not available in the
perl and python perf scripts. (Daniel Bristot de Oliveira)
- Add --repeat global option to 'perf bench' to be used in benchmarks
such as the existing 'futex' one, that was modified to use it
instead of a local option. (Davidlohr Bueso)
- Fix fd -> pathname resolution in 'trace', be it using /proc or a
vfs_getname probe point. (Arnaldo Carvalho de Melo)
- Add suggestion of how to set perf_event_paranoid sysctl, to help
non-root users trying tools like 'trace' to get a working
environment. (Arnaldo Carvalho de Melo)
- Updates from trace-cmd for traceevent plugin_kvm plus args cleanup
(Steven Rostedt, Jan Kiszka)
- Support S/390 in 'perf kvm stat' (Alexander Yarygin)
Tooling infrastructure changes:
- Allow reserving a row for header purposes in the hists browser
(Arnaldo Carvalho de Melo)
- Various fixes and prep work related to supporting Intel PT (Adrian
Hunter)
- Introduce multiple debug variables control (Jiri Olsa)
- Add callchain and additional sample information for python scripts
(Joseph Schuchart)
- More prep work to support Intel PT: (Adrian Hunter)
- Polishing 'script' BTS output
- 'inject' can specify --kallsym
- VDSO is per machine, not a global var
- Expose data addr lookup functions previously private to 'script'
- Large mmap fixes in events processing
- Include standard stringify macros in power pc code (Sukadev
Bhattiprolu)
Tooling cleanups:
- Convert open coded equivalents to asprintf() (Andy Shevchenko)
- Remove needless reassignments in 'trace' (Arnaldo Carvalho de Melo)
- Cache the is_exit syscall test in 'trace) (Arnaldo Carvalho de
Melo)
- No need to reimplement err() in 'perf bench sched-messaging', drop
barf(). (Davidlohr Bueso).
- Remove ev_name argument from perf_evsel__hists_browse, can be
obtained from the other parameters. (Jiri Olsa)
Tooling fixes:
- Fix memory leak in the 'sched-messaging' perf bench test.
(Davidlohr Bueso)
- The -o and -n 'perf bench mem' options are mutually exclusive, emit
error when both are specified. (Davidlohr Bueso)
- Fix scrollbar refresh row index in the ui browser, problem exposed
now that headers will be added and will be allowed to be switched
on/off. (Jiri Olsa)
- Handle the num array type in python properly (Sebastian Andrzej
Siewior)
- Fix wrong condition for allocation failure (Jiri Olsa)
- Adjust callchain based on DWARF debug info on powerpc (Sukadev
Bhattiprolu)
- Fix a risk for doing free on uninitialized pointer in traceevent
lib (Rickard Strandqvist)
- Update attr test with PERF_FLAG_FD_CLOEXEC flag (Jiri Olsa)
- Enable close-on-exec flag on perf file descriptor (Yann Droneaud)
- Fix build on gcc 4.4.7 (Arnaldo Carvalho de Melo)
- Event ordering fixes (Jiri Olsa)"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (123 commits)
Revert "perf tools: Fix jump label always changing during tracing"
perf tools: Fix perf usage string leftover
perf: Check permission only for parent tracepoint event
perf record: Store PERF_RECORD_FINISHED_ROUND only for nonempty rounds
perf record: Always force PERF_RECORD_FINISHED_ROUND event
perf inject: Add --kallsyms parameter
perf tools: Expose 'addr' functions so they can be reused
perf session: Fix accounting of ordered samples queue
perf powerpc: Include util/util.h and remove stringify macros
perf tools: Fix build on gcc 4.4.7
perf tools: Add thread parameter to vdso__dso_findnew()
perf tools: Add dso__type()
perf tools: Separate the VDSO map name from the VDSO dso name
perf tools: Add vdso__new()
perf machine: Fix the lifetime of the VDSO temporary file
perf tools: Group VDSO global variables into a structure
perf session: Add ability to skip 4GiB or more
perf session: Add ability to 'skip' a non-piped event stream
perf tools: Pass machine to vdso__dso_findnew()
perf tools: Add dso__data_size()
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle are:
- big rtmutex and futex cleanup and robustification from Thomas
Gleixner
- mutex optimizations and refinements from Jason Low
- arch_mutex_cpu_relax() removal and related cleanups
- smaller lockdep tweaks"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
arch, locking: Ciao arch_mutex_cpu_relax()
locking/lockdep: Only ask for /proc/lock_stat output when available
locking/mutexes: Optimize mutex trylock slowpath
locking/mutexes: Try to acquire mutex only if it is unlocked
locking/mutexes: Delete the MUTEX_SHOW_NO_WAITER macro
locking/mutexes: Correct documentation on mutex optimistic spinning
rtmutex: Make the rtmutex tester depend on BROKEN
futex: Simplify futex_lock_pi_atomic() and make it more robust
futex: Split out the first waiter attachment from lookup_pi_state()
futex: Split out the waiter check from lookup_pi_state()
futex: Use futex_top_waiter() in lookup_pi_state()
futex: Make unlock_pi more robust
rtmutex: Avoid pointless requeueing in the deadlock detection chain walk
rtmutex: Cleanup deadlock detector debug logic
rtmutex: Confine deadlock logic to futex
rtmutex: Simplify remove_waiter()
rtmutex: Document pi chain walk
rtmutex: Clarify the boost/deboost part
rtmutex: No need to keep task ref for lock owner check
rtmutex: Simplify and document try_to_take_rtmutex()
...
to the ftrace function callback infrastructure. It's introducing a
way to allow different functions to call directly different trampolines
instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which always
had a different trampoline, but the function tracer trampoline was called
and did basically nothing, and then the function graph tracer trampoline
was called. The difference now, is that the function graph tracer
trampoline can be called directly if a function is only being traced by
the function graph trampoline. If function tracing is also happening on
the same function, the old way is still done.
The accounting for this takes up more memory when function graph tracing
is activated, as it needs to keep track of which functions it uses.
I have a new way that wont take as much memory, but it's not ready yet
for this merge window, and will have to wait for the next one.
Another big change was the removal of the ftrace_start/stop() calls that
were used by the suspend/resume code that stopped function tracing when
entering into suspend and resume paths. The stop of ftrace was done
because there was some function that would crash the system if one called
smp_processor_id()! The stop/start was a big hammer to solve the issue
at the time, which was when ftrace was first introduced into Linux.
Now ftrace has better infrastructure to debug such issues, and I found
the problem function and labeled it with "notrace" and function tracing
can now safely be activated all the way down into the guts of suspend
and resume.
Other changes include clean ups of uprobe code.
Clean up of the trace_seq() code.
And other various small fixes and clean ups to ftrace and tracing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT35zXAAoJEKQekfcNnQGuOz0H/38zqM0nLFhrgvz3EPk2UOjn
xqpX8qyb2V7TJZL+IqeXU2a5cQZl5ba0D4WtBGpxbTae3CJYiuQ87iKUNFoH0om5
FDpn80igb368k8V3qRdRsziKVCCf0XBd/NkHJXc0ZkfXGyzB2Ga4bBxALxp2gj9y
bnO+vKo6+tWYKG4hyQb4P3LRXUrK8/LWEsPr39cH2QH1Rdj69Lx9CgrCdUVJmwcb
Bj8hEiLXL/RYCFNn79A3wNTUvW0rG/AOIf4SLqXtasSRZ0ToaU0ZyDnrNv+0Ol47
rX8tSk+LfXchL9hpIvjCf1vlAYq3pO02favteR/jip3lx/dTjEDE4RJ9qtJzZ4Q=
=fwQY
-----END PGP SIGNATURE-----
Merge tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This pull request has a lot of work done. The main thing is the
changes to the ftrace function callback infrastructure. It's
introducing a way to allow different functions to call directly
different trampolines instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which
always had a different trampoline, but the function tracer trampoline
was called and did basically nothing, and then the function graph
tracer trampoline was called. The difference now, is that the
function graph tracer trampoline can be called directly if a function
is only being traced by the function graph trampoline. If function
tracing is also happening on the same function, the old way is still
done.
The accounting for this takes up more memory when function graph
tracing is activated, as it needs to keep track of which functions it
uses. I have a new way that wont take as much memory, but it's not
ready yet for this merge window, and will have to wait for the next
one.
Another big change was the removal of the ftrace_start/stop() calls
that were used by the suspend/resume code that stopped function
tracing when entering into suspend and resume paths. The stop of
ftrace was done because there was some function that would crash the
system if one called smp_processor_id()! The stop/start was a big
hammer to solve the issue at the time, which was when ftrace was first
introduced into Linux. Now ftrace has better infrastructure to debug
such issues, and I found the problem function and labeled it with
"notrace" and function tracing can now safely be activated all the way
down into the guts of suspend and resume
Other changes include clean ups of uprobe code, clean up of the
trace_seq() code, and other various small fixes and clean ups to
ftrace and tracing"
* tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (57 commits)
ftrace: Add warning if tramp hash does not match nr_trampolines
ftrace: Fix trampoline hash update check on rec->flags
ring-buffer: Use rb_page_size() instead of open coded head_page size
ftrace: Rename ftrace_ops field from trampolines to nr_trampolines
tracing: Convert local function_graph functions to static
ftrace: Do not copy old hash when resetting
tracing: let user specify tracing_thresh after selecting function_graph
ring-buffer: Always run per-cpu ring buffer resize with schedule_work_on()
tracing: Remove function_trace_stop and HAVE_FUNCTION_TRACE_MCOUNT_TEST
s390/ftrace: remove check of obsolete variable function_trace_stop
arm64, ftrace: Remove check of obsolete variable function_trace_stop
Blackfin: ftrace: Remove check of obsolete variable function_trace_stop
metag: ftrace: Remove check of obsolete variable function_trace_stop
microblaze: ftrace: Remove check of obsolete variable function_trace_stop
MIPS: ftrace: Remove check of obsolete variable function_trace_stop
parisc: ftrace: Remove check of obsolete variable function_trace_stop
sh: ftrace: Remove check of obsolete variable function_trace_stop
sparc64,ftrace: Remove check of obsolete variable function_trace_stop
tile: ftrace: Remove check of obsolete variable function_trace_stop
ftrace: x86: Remove check of obsolete variable function_trace_stop
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT1VYNAAoJEHm+PkMAQRiGQJwIAKSYp1Uqz5O/e5r0V1TlZKT4
1B4Njopl57PwSrJQWcGEuH2yHyM896vfPO4L6BJIOfyWzh8kwpQqclDt6uhXoF/v
OsO1zb/7/j+n/pDZsePqP9AyIgErsHEBgUbhecDqzjN++ITPcZjQ6TIMPglZaumN
jFAdAZuAaEwqAk8jqN2wlm689Fh9MuUEarHXbXLCqu5RgLrWhFGhp/cTWY62aqnZ
XfEeQ9KtpRZmlR/IYjerbb1eRH7ZdJsZ88WngLX9dj/JdNxHWBkWQBXGAusXk5Fk
y6LsIV3TjyBdrRKJ1Ifyg/2EIXHNBs8HxTFGXpjtp2HPuMLDxZOWOWikb9URtNg=
=Fjf4
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc7' into perf/core, to merge in the latest fixes before applying new changes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When compiling a SH2A kernel (e.g. se7206_defconfig or rsk7203_defconfig)
using sh4-linux-gcc, linking fails with:
net/built-in.o: In function `__sk_run_filter':
net/core/filter.c:566: undefined reference to `__fpscr_values'
net/core/filter.c:269: undefined reference to `__fpscr_values'
...
net/built-in.o:net/core/filter.c:580: more undefined references to `__fpscr_values' follow
This happens because sh4-linux-gcc doesn't support the "-m2a-nofpu",
which is thus filtered out by "$(call cc-option, ...)".
As compiling using sh4-linux-gcc is useful for compile coverage, also
try passing "-m4-nofpu" (which is presumably filtered out when using a
real sh2a-linux toolchain) to disable the generation of FPU instructions
and references to __fpscr_values[].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nothing sets function_trace_stop to disable function tracing anymore.
Remove the check for it in the arch code.
[ Please test this on your arch ]
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
ftrace_stop() is going away as it disables parts of function tracing
that affects users that should not be affected. But ftrace_graph_stop()
is built on ftrace_stop(). Here's another example of killing all of
function tracing because something went wrong with function graph
tracing.
Instead of disabling all users of function tracing on function graph
error, disable only function graph tracing. To do this, the arch code
must call ftrace_graph_is_dead() before it implements function graph.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Because of the removal of the scsi_tgt kernel module, the kbuild variables
CONFIG_SCSI_TGT, CONFIG_SCSI_SRP_TGT_ATTRS and CONFIG_SCSI_FC_TGT_ATTRS
are obsolete. This patch removes these variables. This patch is the result
of the following command:
find -name '*defconfig' | while read f; do grep -vwE 'CONFIG_SCSI_TGT|CONFIG_SCSI_SRP_TGT_ATTRS|CONFIG_SCSI_FC_TGT_ATTRS|CONFIG_SRP' $f >/tmp/t && mv /tmp/t $f; done
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
The arch_mutex_cpu_relax() function, introduced by 34b133f, is
hacky and ugly. It was added a few years ago to address the fact
that common cpu_relax() calls include yielding on s390, and thus
impact the optimistic spinning functionality of mutexes. Nowadays
we use this function well beyond mutexes: rwsem, qrwlock, mcs and
lockref. Since the macro that defines the call is in the mutex header,
any users must include mutex.h and the naming is misleading as well.
This patch (i) renames the call to cpu_relax_lowlatency ("relax, but
only if you can do it with very low latency") and (ii) defines it in
each arch's asm/processor.h local header, just like for regular cpu_relax
functions. On all archs, except s390, cpu_relax_lowlatency is simply cpu_relax,
and thus we can take it out of mutex.h. While this can seem redundant,
I believe it is a good choice as it allows us to move out arch specific
logic from generic locking primitives and enables future(?) archs to
transparently define it, similarly to System Z.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bharat Bhushan <r65777@freescale.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Joe Perches <joe@perches.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Joseph Myers <joseph@codesourcery.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Qiaowei Ren <qiaowei.ren@intel.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Stratos Karafotis <stratosk@semaphore.gr>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vasily Kulikov <segoon@openwall.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Cc: Waiman Long <Waiman.Long@hp.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: adi-buildroot-devel@lists.sourceforge.net
Cc: linux390@de.ibm.com
Cc: linux-alpha@vger.kernel.org
Cc: linux-am33-list@redhat.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linux-cris-kernel@axis.com
Cc: linux-hexagon@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux@lists.openrisc.net
Cc: linux-m32r-ja@ml.linux-m32r.org
Cc: linux-m32r@ml.linux-m32r.org
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-metag@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-parisc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-xtensa@linux-xtensa.org
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/1404079773.2619.4.camel@buesod1.americas.hpqcorp.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Also add a few definitions that were missing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current fsi driver is using SNDRV_DMA_TYPE_CONTINUOUS
for snd_pcm_lib_preallocate_pages_for_all().
But, it came from original dma-sh7760.c,
and no longer needed.
This patch exchange its parameter, and removed
original dma mapping and un-needed
dma_sync_single_xxx() from driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Transition to using the new generic PERF_PMU_CAP_NO_INTERRUPT method for
failing a sampling event when no PMU interrupt is available.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-sh@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1406150205300.16738@vincent-weaver-1.umelst.maine.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Strings library contributed to glibc but re-licensed under GPLv2)
- Optimised crypto algorithms making use of the ARMv8 crypto extensions
(together with kernel API for using FPSIMD instructions in interrupt
context)
- Ftrace support
- CPU topology parsing from DT
- ESR_EL1 (Exception Syndrome Register) exposed to user space signal
handlers for SIGSEGV/SIGBUS (useful to emulation tools like Qemu)
- 1GB section linear mapping if applicable
- Barriers usage clean-up
- Default pgprot clean-up
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=Jj8U
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux into next
Pull arm64 updates from Catalin Marinas:
- Optimised assembly string/memory routines (based on the AArch64
Cortex Strings library contributed to glibc but re-licensed under
GPLv2)
- Optimised crypto algorithms making use of the ARMv8 crypto extensions
(together with kernel API for using FPSIMD instructions in interrupt
context)
- Ftrace support
- CPU topology parsing from DT
- ESR_EL1 (Exception Syndrome Register) exposed to user space signal
handlers for SIGSEGV/SIGBUS (useful to emulation tools like Qemu)
- 1GB section linear mapping if applicable
- Barriers usage clean-up
- Default pgprot clean-up
Conflicts as per Catalin.
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (57 commits)
arm64: kernel: initialize broadcast hrtimer based clock event device
arm64: ftrace: Add system call tracepoint
arm64: ftrace: Add CALLER_ADDRx macros
arm64: ftrace: Add dynamic ftrace support
arm64: Add ftrace support
ftrace: Add arm64 support to recordmcount
arm64: Add 'notrace' attribute to unwind_frame() for ftrace
arm64: add __ASSEMBLY__ in asm/insn.h
arm64: Fix linker script entry point
arm64: lib: Implement optimized string length routines
arm64: lib: Implement optimized string compare routines
arm64: lib: Implement optimized memcmp routine
arm64: lib: Implement optimized memset routine
arm64: lib: Implement optimized memmove routine
arm64: lib: Implement optimized memcpy routine
arm64: defconfig: enable a few more common/useful options in defconfig
ftrace: Make CALLER_ADDRx macros more generic
arm64: Fix deadlock scenario with smp_send_stop()
arm64: Fix machine_shutdown() definition
arm64: Support arch_irq_work_raise() via self IPIs
...
__get_cpu_var() is used for multiple purposes in the kernel source. One
of them is address calculation via the form &__get_cpu_var(x). This
calculates the address for the instance of the percpu variable of the
current processor based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less
registers are used when code is generated.
At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.
The patch set includes passes over all arches as well. Once these
operations are used throughout then specialized macros can be defined in
non -x86 arches as well in order to optimize per cpu access by f.e. using
a global register that may be set to the per cpu base.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
__this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
__this_cpu_inc(y)
Signed-off-by: Christoph Lameter <cl@linux.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org> [compilation only]
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently hugepage migration is available for all archs which support
pmd-level hugepage, but testing is done only for x86_64 and there're
bugs for other archs. So to avoid breaking such archs, this patch
limits the availability strictly to x86_64 until developers of other
archs get interested in enabling this feature.
Simply disabling hugepage migration on non-x86_64 archs is not enough to
fix the reported problem where sys_move_pages() hits the BUG_ON() in
follow_page(FOLL_GET), so let's fix this by checking if hugepage
migration is supported in vma_migratable().
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big USB driver pull request for 3.16-rc1.
Nothing huge here, but lots of little things in the USB core, and in
lots of drivers. Hopefully the USB power management will be work better
now that it has been reworked to do per-port power control dynamically.
There's also a raft of gadget driver updates and fixes, CONFIG_USB_DEBUG
is finally gone now that everything has been converted over to the
dynamic debug inteface, the last hold-out drivers were cleaned up and
the config option removed. There were also other minor things all
through the drivers/usb/ tree, the shortlog shows this pretty well.
All have been in linux-next, including the very last patch, which came
from linux-next to fix a build issue on some platforms.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONYEMACgkQMUfUDdst+ynxvgCggMQBhN5icth8Y5hFglNNaISN
c4AAoMHR2kb62U1plylLbPnboQTjfcl0
=fG6y
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb into next
Pull USB driver updates from Greg KH:
"Here is the big USB driver pull request for 3.16-rc1.
Nothing huge here, but lots of little things in the USB core, and in
lots of drivers. Hopefully the USB power management will be work
better now that it has been reworked to do per-port power control
dynamically. There's also a raft of gadget driver updates and fixes,
CONFIG_USB_DEBUG is finally gone now that everything has been
converted over to the dynamic debug inteface, the last hold-out
drivers were cleaned up and the config option removed. There were
also other minor things all through the drivers/usb/ tree, the
shortlog shows this pretty well.
All have been in linux-next, including the very last patch, which came
from linux-next to fix a build issue on some platforms"
* tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (314 commits)
usb: hub_handle_remote_wakeup() only exists for CONFIG_PM=y
USB: orinoco_usb: remove CONFIG_USB_DEBUG support
USB: media: lirc: igorplugusb: remove CONFIG_USB_DEBUG support
USB: media: streamzap: remove CONFIG_USB_DEBUG
USB: media: redrat3: remove CONFIG_USB_DEBUG usage
USB: media: redrat3: remove unneeded tracing macro
usb: qcserial: add additional Sierra Wireless QMI devices
usb: host: max3421-hcd: Use module_spi_driver
usb: host: max3421-hcd: Allow platform-data to specify Vbus polarity
usb: host: max3421-hcd: fix "spi_rd8" uses dynamic stack allocation warning
usb: host: max3421-hcd: Fix missing unlock in max3421_urb_enqueue()
usb: qcserial: add Netgear AirCard 341U
Documentation: dt-bindings: update xhci-platform DT binding for R-Car H2 and M2
usb: host: xhci-plat: add xhci_plat_start()
usb: host: max3421-hcd: Fix potential NULL urb dereference
Revert "usb: gadget: net2280: Add support for PLX USB338X"
USB: usbip: remove CONFIG_USB_DEBUG reference
USB: remove CONFIG_USB_DEBUG from defconfig files
usb: resume child device when port is powered on
usb: hub_handle_remote_wakeup() depends on CONFIG_PM_RUNTIME=y
...
The bulk of this branch is updates for Renesas Shmobile. They are still
doing some enablement for classic boards first, and then come up with DT
bindings when they've had a chance to learn more about the hardware. Not
necessarily a bad way to go about it, and they're looking at moving some
of the temporary board code resulting from it to drivers/staging instead
to avoid the churn here.
As a result of the shmobile clock cleanups, we end up merging quite a
bit of SH code here as well. We ended up merging it here instead of in
the cleanup branch due to the other board changes depending on it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTjNClAAoJEIwa5zzehBx3Q7wP+wYzWTAU0+3BnnjJpQM79hsX
1hP89RaM6DEyTf6PiL/AKOHsnDponUhNzZu1W5FvNG6cFVenh/nxbmO65FKX9CrY
Ap2pkQW+/IcpmIKZ+Hln2bkCc54a6yPouK+5pd9W14X5TtqNmLbdh1qhoq9UjFTo
zgLfhch5tyNqfpNOj0vFsmvTw0ZGJ0Neq6olRqQbXmyAaRaWzDa64lmEKVupMdk7
2Fh/8jeXlVlryi7p7CvNoAmZEMm7+We5ZMVsQXLk8b9zcwuCWK0DZzNW4DnRCB1d
lsNM/Sygi3Y5zRj2XogNANVhNDIih0f50FX7uuKtmevWNJE9n4To7uFUMTk/3zBt
1hvJLL8w4WHhzkg5v5nFsiCTx65pFaTD/LocPj8lhQ1AYzUvWN5sKPxW0uC1lvJ9
Unlwdc0C4EWs3yq6hAPUZS2eB7owmzNUWdjdkgKfdc74u5RnRay0pUmbRMJm2l20
OKoDSwaluQZUeHrxPnTSLdgpkBbPRn9M5DbswEQsuPyI6yROgCRxaRQ4XcpM93dV
4obCF+fOvX6dtsdIUBCtdhvmJ/iHqhQlPLc2avpt2gyti7eWjQkt5it12hjjOF6A
DVBdNHv215EEgvB0MbPJvFVKBLw4boxdeBx+FqMQCqvAbqefHo4gcQZcsUGAv/pX
zJ8jgkYhlt7XTd+6GlJu
=lWof
-----END PGP SIGNATURE-----
Merge tag 'boards-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC board support updates from Olof Johansson:
"The bulk of this branch is updates for Renesas Shmobile. They are
still doing some enablement for classic boards first, and then come up
with DT bindings when they've had a chance to learn more about the
hardware. Not necessarily a bad way to go about it, and they're
looking at moving some of the temporary board code resulting from it
to drivers/staging instead to avoid the churn here.
As a result of the shmobile clock cleanups, we end up merging quite a
bit of SH code here as well. We ended up merging it here instead of
in the cleanup branch due to the other board changes depending on it"
* tag 'boards-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (130 commits)
ARM: davinci: remove checks for CONFIG_USB_MUSB_PERIPHERAL
ARM: add drivers for Colibri T30 to multi_v7_defconfig
ARM: shmobile: Remove Genmai reference DTS
ARM: shmobile: Let Genmai multiplatform boot with Genmai DTB
ARM: shmobile: Sync Genmai DTS with Genmai reference DTS
ARM: shmobile: genmai-reference: Remove legacy clock support
ARM: shmobile: Remove non-multiplatform Genmai reference support
ARM: configs: enable XHCI mvebu support in multi_v7_defconfig
ARM: OMAP: replace checks for CONFIG_USB_GADGET_OMAP
ARM: OMAP: AM3517EVM: remove check for CONFIG_PANEL_SHARP_LQ043T1DG01
ARM: OMAP: SX1: remove check for CONFIG_SX1_OLD_FLASH
ARM: OMAP: remove some dead code
ARM: OMAP: omap3stalker: remove two Kconfig macros
ARM: tegra: tegra_defconfig updates
ARM: shmobile: r7s72100: use workaround for non DT-clocks
ARM: shmobile: Add forward declaration of struct clk to silence warning
ARM: shmobile: r7s72100: remove SPI DT clocks from legacy clock support
ARM: shmobile: r7s72100: add spi clocks to dtsi
ARM: shmobile: r7s72100: remove I2C DT clocks from legacy clock support
ARM: shmobile: r7s72100: add i2c clocks to dtsi
...
* pci/misc:
PCI: Fix return value from pci_user_{read,write}_config_*()
PCI: Turn pcibios_penalize_isa_irq() into a weak function
PCI: Test for std config alias when testing extended config space
Now that CONFIG_USB_DEBUG is gone, remove it from a number of defconfig
files that were enabling it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pcibios_penalize_isa_irq() is only implemented by x86 now, and legacy ISA
is not used by some architectures. Make pcibios_penalize_isa_irq() a
__weak function to simplify the code. This removes the need for new
platforms to add stub implementations of pcibios_penalize_isa_irq().
[bhelgaas: changelog, comments]
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
