- improve handling of the EXTERN input: don't start an unnecessary carrier scan
- improve the LOG_STATUS output
- ensure that a carrier scan is started again when switching back to the tuner.
- set correct prescale for L-NICAM
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is some old code in the or51133 firmware loading function that
has no effect. Left a comment to in case it helps someone trying
to reverse engineer the chip.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move <linux/usb_input.h> to <linux/usb/input.h> and remove some
redundant includes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various drivers use xmit_lock internally to synchronise with their
transmission routines. They do so without setting xmit_lock_owner.
This is fine as long as netpoll is not in use.
With netpoll it is possible for deadlocks to occur if xmit_lock_owner
isn't set. This is because if a printk occurs while xmit_lock is held
and xmit_lock_owner is not set can cause netpoll to attempt to take
xmit_lock recursively.
While it is possible to resolve this by getting netpoll to use
trylock, it is suboptimal because netpoll's sole objective is to
maximise the chance of getting the printk out on the wire. So
delaying or dropping the message is to be avoided as much as possible.
So the only alternative is to always set xmit_lock_owner. The
following patch does this by introducing the netif_tx_lock family of
functions that take care of setting/unsetting xmit_lock_owner.
I renamed xmit_lock to _xmit_lock to indicate that it should not be
used directly. I didn't provide irq versions of the netif_tx_lock
functions since xmit_lock is meant to be a BH-disabling lock.
This is pretty much a straight text substitution except for a small
bug fix in winbond. It currently uses
netif_stop_queue/spin_unlock_wait to stop transmission. This is
unsafe as an IRQ can potentially wake up the queue. So it is safer to
use netif_tx_disable.
The hamradio bits used spin_lock_irq but it is unnecessary as
xmit_lock must never be taken in an IRQ handler.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mixing "depends on I2C" and "select I2C" within the media subsystem
leads to the following problem:
Warning! Found recursive dependency: I2C DVB_BUDGET DVB_BUDGET_PATCH
DVB_AV7110 VIDEO_SAA7146_VV VIDEO_SAA7146 I2C
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
reference to .init.text: from .text between 'dvb_bt8xx_probe'
(at offset 0x122c) and 'dvb_bt8xx_remove'
reference to .init.text: from .text between 'dvb_bt8xx_probe'
(at offset 0x1267) and 'dvb_bt8xx_remove'
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If CONFIG_VIDEO_DEV=m and CONFIG_VIDEO_V4L1_COMPAT=y, v4l1-compat should
be built as a module (currently, it isn't built at all leading to
problems with modules using it).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes two off-by-one errors spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/vivi.c: In function `vivi_map_sg':
drivers/media/video/vivi.c:799: error: `DMA_NONE' undeclared (first use in this function)
drivers/media/video/vivi.c:799: error: (Each undeclared identifier is reported only once
drivers/media/video/vivi.c:799: error: for each function it appears in.)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Frequency range values in the current driver for the LG TDVS H06xF tuners
appear to have been a transposing of the 5 in the mid range 160-455 instead
of 165-450.
This patch corrects the pll programming for these tuners as per the datasheet.
Signed-off-by: Rusty Scott <rustys@ieee.org>
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is a missing break in card initialization function. Might screw
up initialization of Terratec Cinergy 400 TV.
Signed-off-by: Mikhail Gusarov <dottedmag@dottedmag.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The fast firmware load hack in cx25840 uses private data. In fact, it
breaks pvrusb2 and doesn't work at all with ivtv. It is a unsafe
implementation and so it is removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch prevents a bug where the frontend is unable to tune after waking
from powered down state. Now, the device remains powered on until it is
disconnected, just like the windows driver. It seems that the bluebird
firmware is unable to successfully handle tuning after a powered down state.
This patch fixes all of the FusionHDTV Bluebird USB2 devices. The Medion
MD95700 will still behave as before, since it was unaffected by this bug.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*) Allow forcing the bandselect value with a module parameter to
facilitate determining the correct bandselect frequencies.
*) Changes the bandselect frequency thresholds based on experiments
with the above parameter in conjunction with the values in the spec.
Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*) Sets an additional tuner parameter (demodulator sample gain) that
wasn't being set before.
*) Removes the low symbol rate tuner parameter tweaks in the previous
patch -- it appears those tweaks are not necessary with the demodulator
sample gain set correctly.
*) Cleanup and document the demodulator register initialization sequence.
*) Change set_fec routine to disable FEC auto scan when a specific code
rate is selected.
*) Remove error message when reported FEC is invalid (which happens
sometimes when the card has no signal)
Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The previous DISEQC code didn't wait, so it was unreliable
Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Current debug messages at cx24123 are next to useless, since they don't
print the values sent/read to registers. With this patch, debug=1 will
show comprehensive messages. debug=2 will show also read/write operations
at I2C bus.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
- fixed the reception of channels with low symbol rates.
( The VGA1 and VGA2 offsets recommended by cx24109 docs for
symbol rates from 1 to 5 MSps do not work. I changed them
to values found experimentally. The charge pump current
and FILTUNE voltage are now set to values recommended in
the docs. This improves reception for symbol rates < 15 MSps.
The values written in the SYSSymbolRate registers are calculated
with better precision. )
- fixed the cx24123_get_fec() function. It was returning the values
for DCII mode.
- removed some unused variables
Signed-off-by: Vadim Catana <skystar at moldova.cc>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In several places we use dev->devno right after we kfree() dev. This fixes
coverity bug id #1065
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L1 API is depreciated and should be removed soon from kernel. This patch
adds two new options, one to disable V4L1 drivers, and another to disable
V4L1 compat module. This way, it would be easy to check what still depends
on V4L1 stuff, allowing also to test if app works fine with V4L2 only support.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Witout this patch tv out don't work properly with my pvr350 card.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The computation in cx88_risc_buffer suffers from the mistake:
a non-zero padding value can cause more page borders to be crossed,
leading to big buffer over-runs.
This patch changes the additive constant from 3 + 4 to 4
It also changees the constant in cx88_risc_databuffer from 3 + 4 to 2,
because 2 dwords are the correct vaule.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It looks like the HD3000 was prototyped with the 7610 tuner when
the driver was developed, but the cards appear to have always shipped
with the 7612 tuner and the driver was never adjusted for it.
The definition needs to be corrected.
- The HD-3000 was prototyped with a Thomson DTT7610,
but production versions used a DTT7612 tuner.
- This patch changes both dvb-pll settings and V4L tuner type.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Spotted a couple more places where it fails to check if
dvb_register_adapter() fails.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that the CI code reinitialises the frontend, need to move the CI
initialisation to after the frontend init in order to ensure the frontend is
always in a good state. Fixes an oops caused by the frontend being NULL as
well.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When disable_ir=1 parameter is used, or when saa7134_input_init1()
fails for any other reason, dev->remote will remain NULL, and the
driver will oops in saa7134_hwinit2(). Therefore dev->remote must be
checked before dereferencing.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It turns out the firmware on the TT budget-ci 1.1 slots doesn't generate
interrupts. This patch adds support for this using polling mode on these
slots.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This mutex is meant to stop two devices getting the same ID. dvbdev_get_free_id()
scans the list of already allocated devices to find a free id.
Unfortunately, since the mutex is unlocked before the card is added to the
above list, it is still possible for two of them to get the same id.
Its debatable whether this mutex lock is actually needed, but I'm unwilling
to just remove it in case something does depend on it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are tree mistakes on bttv_risc_overlay.
1) When skip_odd is true, the number of lines for which
instructions are written is (height+1)/2, not height/2.
2) This occurs when clipping: the number of instruction bytes
written can be as much as 8 + 12*nclips, not 8 + 8*nclips, as
currently estimated.
3) Coverity check were wrong with nskips=0, since it means that
it can clipped at most one line.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kconfig: fix typo in change count initialization
kconfig: recenter menuconfig
kconfig: revert conf behaviour change
kconfig: fix default value for choice input
kbuild: fix NULL dereference in scripts/mod/modpost.c
kbuild: fix mode of checkstack.pl and other files.
kbuild: rebuild initramfs if content of initramfs changes
kbuild: properly pass options to hostcc when doing make O=..
kbuild: modules_install for external modules must not remove existing modules
kbuild: fix make dir/
ver_linux: don't print reiser4progs version if none found
kbuild: mips: fix sed regexp to generate asm-offset.h
kbuild: fix building single targets with make O=.. single-target
kbuild: use relative path to -I
kbuild: fix unneeded rebuilds in drivers/net/chelsio after moving source tree
kbuild: fix unneeded rebuilds in drivers/media/video after moving source tree
kbuild: fix garbled text in modules.txt
These are the last conversions of pci_set_dma_mask(),
pci_set_consistent_dma_mask() and pci_dma_supported() to use DMA_xBIT_MASK
constants from linux/dma-mapping.h
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using a relative path has the advantage that when the kernel source
tree is moved the relevant .o files will not be rebuild just because
the path to the kernel src has changed.
This also got rid of a user of TOPDIR - which has been deprecated for a long time now.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This fixes some uneeded rebuilds under drivers/media/video after moving
the source tree. The makefiles used $(src) and $(srctree) for include
paths, which is unnecessary. Changed to use relative paths.
Compile tested, produces byte-identical code to the previous makefiles.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Fix address space warning (from sparse):
drivers/media/video/cpia2/cpia2_core.c:2355:6: error: symbol 'cpia2_read' redeclared with different type (originally declared at drivers/media/video/cpia2/cpia2.h:458) - incompatible argument 2 (different address spaces)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Renamed various msp3400 routing defines to be more consistent and less
confusing. Esp. the MSP_DSP_OUT defines were confusing since it is really
a DSP input.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Remove old DECODER_ commands from tvp5150.c, replacing them with newer
ones if appropriate.
- Small VIDIOC_G_TUNER fixes in msp3400 and tuner.
- Fix VIDIOC_S_TUNER support in em28xx.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- msp3400c did not detect the second carrier, thus being always mono.
- properly mute the msp3400c while detecting the carrier.
- fix checks on the presence of scart2/3 inputs and scart 2 output.
- implement proper audio mode fallbacks for msp3400c/d, identical to the
way msp3400g works.
- MODE_STEREO no longer produces dual languages when set for a bilingual
transmission, instead it falls back to LANG1. Use LANG1_LANG2 to hear
both languages of a bilingual transmission. This is much more intuitive
for the user and is in accordance with the preferred usage in the v4l2
specification.
- bttv tried to implement v4l2 calls with v4l1 calls to the i2c devices,
completely mangling the audmode/rxsubchans handling. v4l2 calls now do
v4l2 calls to the i2c devices.
- fixed broken i2c_vidiocschan in bttv.
- add start/end lines to LOG_STATUS.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The sliced VBI defines added in videodev2.h are removed since requires
more discussion.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes a dependency problem that affected the indentation order
within the individual frontend selection support menus for cx88-dvb.
- created a boolean dependency link for VIDEO_CX88_VP3054, so that
it's tristate value will be the same as that of VIDEO_CX88_DVB.
- VIDEO_CX88_VP3054 is automatically selected by VIDEO_CX88_DVB_ALL_FRONTENDS,
but is otherwise selected by VIDEO_CX88_DVB_VP3054, offered as an option
under VIDEO_CX88_DVB_MT352
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Unfortunately on the budget-av board, the CAM reset line is tied to the
frontend reset line, so resetting the CAM also zaps the frontend. This
breaks the tda1004x at least, and causes it to fail to tune until the
budget-av module is reloaded. This patch adds an exported function to dvb_frontend
that allows a card to forcibly reinitialise a frontend. The budget-av now
does this on CAM reset, which corrects this problem.
since they do not tie the CAM reset line to the frontend reset line.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The dvr device could be opened multiple times simultaneously in O_RDONLY mode.
Each open after the first would allocate a new dvr buffer (1880 KB) and leak
the old buffer. The first close would de-allocate the dvr buffer and cause
all other open dvrs to stop working. This patch allows only a single O_RDONLY
open of the drv device, as per the API specification. Multiple O_WRONLY opens
are still allowed and don't appear to cause any problems.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This attached patch was originally proposed by Anssi Hannula to the dvb-kernel
user to choose the default broadcast mode when using the ttpci driver.
NTSC users need to only add the following line to modprobe.d:
options dvb-ttpci tv_standard=1
PAL users will not need to change anything, for this will be the default.
Signed-off-by: C.Y.M <syphir@syphir.sytes.net>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes a typo in a comment.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Issue a warning when more than 80% of the DMA buffer is being used
(probably due to bad IRQ latency). Warnings are rate-limited.
- Introduce a new parameter 'bufsize' (in KByte) which increases the
default DMA buffer of 188 KByte up to 1410 KByte (Activy: 564 KByte).
Signed-off-by: Ingo Schneider <mail@ingo-schneider.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Move documentation for usb v4l devices from
Documentation/usb to Documentation/video4linux.
- Removed trailing whitespace.
- Update Kconfig help text links to reflect the new file locations.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It should be V4L2_TUNER_MODE_LANG1_LANG2. What the code does is check if
we are NTSC and a SAP channel is available. If so, then the msp3400
should switch to standard 0x21 if the user wants to hear the SAP
channel, which is for audio modes LANG2 (aka SAP) and LANG1_LANG2
(bilingual).
In the msp3400 driver STEREO is abused for bilingual in PAL. Bilingual
never worked with NTSC in the past and I decided that I'd better not
use the bad PAL example.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add support for the uPD64031A NEC Electronics Ghost Reduction i2c device
- Add support for the uPD6408x NEC Electronics 3-Dimensional Y/C separation
i2c device.
Signed-off-by: Takahiro Adachi <tadachi@tadachi-net.com>
Signed-off-by: Takeru Komoriya <komoriya@paken.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- The wait time until the first time the audio mode was detected was
1+5=6 seconds instead of just 1 second (wrong statement order).
msp3400c specific bug.
- Implemented audio mode fallback for msp3400c/d just like the msp3400g
does automatically. E.g. fallback to stereo if no second language exists,
etc.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver tried to set a register that is not present on msp3400c devices.
Add the missing test.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the Wolfson Microelectronics WM8739
stereo A/D converter from the ivtv driver.
Many thanks to Takahiro Adachi for writing the original driver.
Signed-off-by: Takahiro Adachi <tadachi@tadachi-net.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Fixed PCI ID typo in VIDEO_CX88_ALSA help text
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There seems to be a new version of the USB DVB-T stick from WideView with a new demod-revision inside and thus a new firwmare.
This patch enables support for that.
Thanks to Mikel Martin for early testing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- removed redundant Video For Linux API help text
- fixed dependency / selection for USB_W9968CF
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There seem to be many variants of this cards with different
feature sets. This entry supports
analog TV, CVBS and s-video input, FM radio and DVB-T
if they are supported by the hardware.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The .vmux entry needs to be 1 instead of 0
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added ID entries for the Genius VideoWonder DVB-T
and the LifeView FlyTV Platinum Gold
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The FWSEND parameter controls the size of the firmware chunks sent
down the I2C bus to the chip. Previously this had been set to 1024
but unfortunately some I2C implementations can't transfer data in such
big gulps. Specifically, the pvrusb2 driver has a hard limit of
around 60 bytes, due to the encapsulation there of I2C traffic into
USB messages. So we have to significantly reduce this parameter.
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to: Andrew Cohen <cohen@andy.bu.edu>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After the recent video-buf "generic" adaptation, the PCI wrappers got
completely broken, and all of the DMA sound modules stopped working (and
failed with an oops)
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added keycodes for the DViCO FusionHDTV portable remote control.
- Enabled the remote control for both versions of FusionHDTV DVB-T USB
and the FusionHDTV 5 USB Gold (ATSC)
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The bt8xx drivers uses request_firmware()
and thus needs to select FW_LOADER.
Signed-off-by: maximilian attems <maks@sternwelten.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
one printk needs a newline at end;
better MODULE_PARM_DESC text formatting;
don't need to init static data to 0;
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The saa7134 drivers uses request_firmware()
and thus needs to select FW_LOADER.
Signed-off-by: maximilian attems <maks@sternwelten.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add missing class check to tveeprom_attach_adapter.
- Add CX2341X specific IR probe address list.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The boot cmdline is parsed in parse_early_param() and
parse_args(,unknown_bootoption).
And __setup() is used in obsolete_checksetup().
start_kernel()
-> parse_args()
-> unknown_bootoption()
-> obsolete_checksetup()
If __setup()'s callback (->setup_func()) returns 1 in
obsolete_checksetup(), obsolete_checksetup() thinks a parameter was
handled.
If ->setup_func() returns 0, obsolete_checksetup() tries other
->setup_func(). If all ->setup_func() that matched a parameter returns 0,
a parameter is seted to argv_init[].
Then, when runing /sbin/init or init=app, argv_init[] is passed to the app.
If the app doesn't ignore those arguments, it will warning and exit.
This patch fixes a wrong usage of it, however fixes obvious one only.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark the f_ops members of inodes as const, as well as fix the
ripple-through this causes by places that copy this f_ops and then "do
stuff" with it.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MODULE_PARM was actually breaking: recent gcc version optimize them out as
unused. It's time to replace the last users, which are generally in the
most unloved drivers anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/media/video/v4l2-common.c: In function `v4l_printk_ioctl_arg':
drivers/media/video/v4l2-common.c:477: warning: `0' flag used with `%p' printf format
Someone went and "improved" my patch ;)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Because of historic reasons, there are two separate directories with
V4L stuff. Most drivers are located at driver/media/video. However, some
code for USB Webcams were inserted under drivers/usb/media.
This makes difficult for module authors to know were things should be.
Also, makes Kconfig menu confusing for normal users.
This patch moves all V4L content under drivers/usb/media to
drivers/media/video, and fixes Kconfig/Makefile entries.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDIOC_G/S_AUDOUT does not belong in msp3400 (it's a user level command,
not to be used in internal i2c drivers). Also fix a compile warning and
improve LOG_STATUS.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a new audio mode V4L2_TUNER_MODE_LANG1_LANG2 (used by VIDIOC_G/S_TUNER).
This mode allows the user to select both languages of a bilingual transmission,
one language on the left, one on the right audio channel. If there is no
bilingual transmission, or it is not supported, then this mode should act like
V4L2_TUNER_MODE_STEREO.
This mode is introduced for PVR-like drivers where it is useful to be able to
record both languages of a bilingual broadcast.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- implement VIDIOC_INT_S_AUDIO_ROUTING for msp3400 and tvaudio
- use the new command in bttv, pvrusb2 and em28xx.
- remove the now obsolete MSP_SET_MATRIX from msp3400 (yeah!)
- remove the obsolete VIDIOC_S_AUDIO from msp3400.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved msp3400.h to msp3400-driver.h.
Created media/msp3400.h with the new routing defines and lots of comments.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Lots of cleanups:
- remove duplicate actions
- add D/K3 Dual FM-Stereo and D/K NICAM FM (HDEV3) support
- put prescales in the proper place
- add missing D/K NICAM
- msp34xxg_reset now only resets instead of also starting the autodetect
(moved that to msp34xxg_thread)
- fix support for SAP.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
msp_modus is 'G' model specific. Moved it to kthreads and also added proper
handling for the Japanese and South Korean TV standards.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For the new routing implementation it is easier if all the 'normal'
scart inputs (IN1-IN4) are consecutive.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cleanup audio input handling in bttv and tvaudio:
- inputs were specified that were never used
- mute was handled as a special input which led to confusing code
- confusing naming made it difficult to see if the setting was for
i2c or gpio.
The old audiochip.h input names moved to tvaudio.h. Currently this
is used both by tvaudio and msp3400 until the msp3400 implements the
new msp3400-specific inputs.
Detect in bttv the tvaudio and msp3400 i2c clients and use these
client pointers to set the inputs directly instead of broadcasting the
command.
Removed AUDC_SET_INPUT. Now replaced by VIDIOC_S_AUDIO. This will be
replaced again later by the new ROUTING commands.
Removed VIDIOC_G_AUDIO implementations in i2c drivers: this command is
a user level command and not to be used internally. It wasn't called at
all anyway.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only the Medion boxes return 0x08 after an i2c read/write.
The bluebird devices do not return anything at all.
This patch conditionalizes the test for the 0x08 return code
to produce a warning message when using the Medion box, only.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- corrects the wording in some of the debug messages.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed the FIXME comment from bluebird_patch_dvico_firmware_download:
/* FIXME: are we allowed to change the fw-data ? */
Yes, we are allowed. DViCO's Windows driver also does the same thing.
A single firmware image is used to support all of the bluebird boxes.
The firmware sets all devices to PID: d700. Instead of using that, the
driver replaces the d700 with the cold PID+1 before the download.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes the (harmless) -ETIMEDOUT during device init
for the DViCO FusionHDTV Bluebird boxes, by conditionalizing the
gpio write inside cxusb_i2c_xfer to happen only for Medion boxes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On ppc64, u64 is `unsigned long'
drivers/media/video/v4l2-common.c: In function `v4l_printk_ioctl_arg':
drivers/media/video/v4l2-common.c:486: warning: cast from pointer to integer of different size
drivers/media/video/v4l2-common.c:580: warning: long long int format, v4l2_std_id arg (arg 8)
drivers/media/video/v4l2-common.c:625: warning: long long int format, v4l2_std_id arg (arg 8)
drivers/media/video/v4l2-common.c:693: warning: long long int format, v4l2_std_id arg (arg 4)
drivers/media/video/v4l2-common.c:910: warning: long long unsigned int format, long unsigned int a$
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There was no MODULE_DEVICE_TABLE for the b2c2-flexcop-usb module. This makes it
impossible for hotplug to load the module automatically, when such a device is
connected.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I2C_foo were used for some i2c addresses. Bad, since those constants could
mean other i2c chip things.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Missing a Makefile for bt8xx
- rds.h were at wrong directory, since it is a global header for an internal
interface
- tda7432 and tda9875 were dependent from bttv.h
- bttv.h were holding i2c addresses
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Virtual Video Device Driver (aka vivi) is a device that
can be used to:
1) test core v4l functionalities;
2) be a prototype for newer development.
Vivi were developed using the best practices for v4l driver.
When loaded, it provides a video device that generates a
standard color bar, with a timestamp placed at top left corner.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Video_buf were concerned to allow PCI devices to be used as
video capture devices. This patch extends video_buf features
by virtualizing pci-dependent functions and allowing other
type of devices to use it.
It is still DMA centric, although it may be used also by
devices that emulates scatter/gather behavior or a DMA device
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several media/video and sound drivers include i2c-dev.h while they
don't need it at all. Clean it up.
This header file is really only needed by i2c-dev.c and
compat_ioctl.c, other drivers should never need it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change all the Zoran (ZR36050/ZR36060) drivers to use i2c_master_send instead
of i2c_transfer when possible. This simplifies the code by a few lines in
each driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drop support for the ENCODER_DUMP command in the adv7175 driver. ENCODER_DUMP
was never actually defined as far as I can see, so the code was ifdef'd out,
and I suspect it was never used, not even once, as it includes an obvious
array overrun.
The register values of this specific chip can be dumped in a generic way using
the i2c-dev driver and the "i2cdump" user-space tool if it is ever really
needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drop the adv7175 register cache, as it is only written to and never read back
from. This saves 128 bytes of memory and slightly speeds up the register
writes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Semaphore to mutexes conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a (probably harmless) array overrun in the DECODER_DUMP command of the
saa7110 driver. No big deal as this command is not used anywhere anyway.
Also reformat the dump so that it displays nicely.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The bt856 driver has a register cache much larger than needed. We really only
write to 3 registers, so a 32-byte cache is a bit too much. We can be just as
efficient with a 6-byte cache. We could even do with a 3-byte cache, but at
the cost of additional arithmetics arguably not worth the spared 3 bytes.
Also, 4 of the 6 other members of the bt856 data structure were not used
anywhere, so we can as well drop them for an additional 16 bytes of memory
spared.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When grabbing composite video with Iomega Buz, the stock driver will
prevent grabbing from the same input twice in a row, forcing the user to
switch inputs before anything useful can be grabbed again. It is caused by
some optimization code in the input selection parts, and triggered by the
saa7111_command() executing cmd 0. The attached patch will remedy this by
disabling cmd 0 altogether; a fix that has no found negative effects on the
rest of the code. In fact, saa7110.c does the exact same thing.
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cleanups to the zr36057 initialization:
* Drop intermediate local variables.
* Single error path.
Also drop a needless cast on kfree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Explicitely state the number of registers the SAA7111 has, and use that
defined value where relevant. This should prevent any future array overrun
like the one I just fixed in the saa7110 driver.
This patch also saves 8 bytes of memory as a side effect, as the register
cache was larger than needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the i2c block write mode of the saa7114 driver. A previous code change
accidentally commented out a local variable increment, which should have been
kept, causing the register writes over the I2C bus to never be batched,
replacing any attempted block write by slower, individual write transactions.
Also drop the commented out code, as it only adds to confusion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This reverts commit 08f1d0b99f
The "bt8xx/ conversion" for drivers/video/ hasn't actually percolated
all the way to this tree, so the Makefile change escaped too soon.
Build breakage noticed by Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some chipsets have several problems when pci to pci transfers are activated
on overlay mode. the option no_overlay allows disabling such feature of
the driver, in favor of keeping the system stable.
The default is to use pcipci_fail flag defined on drivers/pci/quirks.c.
It also allows the user to override it by forcing disable overlay or forcing
enable. Forcing enable may generate PCI transfer corruption, including disk
mass corruption, so should be used with care.
Added a text description to this option and make messages looks the same at
both bttv and saa7134 drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add wss_cfg_4_3 and wss_cfg_16_9 configuration options.
Firmware 2623 or later required.
Both parameters are bit masks:
- bit 15: disable WSS
- bit 14: send short WSS burst, then turn off WSS
- bit 13..0: WSS bits as specified by the standard
These parameters are useful if you own a broken tv set which
does not handle wss correctly.
Default settings:
- wss_cfg_4_3: 0x4008
- wss_cfg_16_9: 0x0007
These should work with most devices.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved duplicated code of ALPS BSRU6 tuner to a standalone file.
Modified av7110 and budget drivers to include the new file.
Signed-off-by: Perceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- removed VIDEO_AUDIO_DECODER Kconfig menu item.
VIDEO_MSP3400, VIDEO_CS53L32A and VIDEO_WM8775 now
each have their own menu items.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- created Kconfig item, VIDEO_CS53L32A, for the cs53l32a module which supports
the Cirrus Logic CS53L32A Low Voltage Stereo A/D Converter.
- created Kconfig item, VIDEO_WM8775, for the wm8775 module which supports
the Wolfson Microelectronics WM8775 high performance stereo A/D Converter.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Corrected typo for NxtWave NXT200X
- Added "Oren" manufacturer name to menu items for OR51132 and OR51211
- Removed "(pcHDTV HDx000 card)" from Oren frontends menu item names,
This isn't necessary, as these frontends are selected by the card drivers,
build configuration (DVB_BT8XX and VIDEO_CX88_DVB).
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CONFIG_VIDEO_CPIA2=y, CONFIG_USB=n results in the following compile
<-- snip -->
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `set_alternate':cpia2_usb.c:(.text+0x443aa2): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `cpia2_usb_stream_resume': undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `cpia2_usb_stream_resume': undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `cpia2_usb_stream_pause': undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `cpia2_usb_stream_pause': undefined reference to `usb_free_urb'
drivers/built-in.o: In function `cpia2_usb_disconnect':cpia2_usb.c:(.text+0x443e14): undefined reference to `usb_driver_release_interface'
drivers/built-in.o: In function `cpia2_usb_transfer_cmd': undefined reference to `usb_control_msg'
drivers/built-in.o: In function `cpia2_usb_transfer_cmd': undefined reference to `usb_control_msg'
drivers/built-in.o: In function `cpia2_usb_complete':cpia2_usb.c:(.text+0x444836): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `cpia2_usb_cleanup': undefined reference to `usb_deregister'
drivers/built-in.o: In function `cpia2_usb_init': undefined reference to `usb_register_driver'
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- removed VIDEO_DECODER Kconfig menu item.
VIDEO_CX25840, VIDEO_SAA711X and VIDEO_SAA7127 now
each have their own menu items.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- created Kconfig menu item, VIDEO_SAA711X, for the saa7115 module,
which supports SAA7113, SAA7114 and SAA7115 video decoders.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The msp3400 driver is currently only being built if
the bttv driver is selected. There are new drivers
that will be needing msp3400, so simply including
msp3400 in the Makefile is no longer appropriate.
This patch creates VIDEO_MSP3400, and alters VIDEO_BT848, VIDEO_PVRUSB2
and VIDEO_AUDIO_DECODER each to select VIDEO_MSP3400.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L2_STD_PAL define is not correct. It specifies only 50Hz PAL standards.
This patch fixes saa7113 color config for other PAL video standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes chroma standard selection based at possible values,
according with datasheet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now, em28xx uses saa7115 instead of saa711x.
saa7115 driver is capable of handling saa 7113, 7114 and 7115.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Detaching the device didn't clean up several device files in /dev/dvb,
after applying that patch all dvb devices disappeared as expected.
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The device, Medion 7134, has two saa7134 chips on it, but only one of them
is functional in the current saa7134 driver.
This patch adds autodetection for the second, unsupported saa7134 chip,
as SAA7134_BOARD_MD7134_BRIDGE_2, and displays a message to the user
(in dmesg) indicating that the second chip isn't yet functional.
This is useful for users, since two instances of the saa7134 driver
will spawn. This patch will prevent confusion by warning the user that
only one of the chips on the board are functional.
There are other versions of the SAA7134_BOARD_MD7134 with only a single
saa7134 bridge/decoder -- those devices will not be affected by this patch.
Only devices containing the second chip will display the warning.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are already some supported devices that contain two
saa713x chips on-board, where only one of these chips is
currently functional in the driver.
We are already printing a warning message for the second
saa7134 decoder in SAA7134_BOARD_AVERMEDIA_A169_B. This
patch alters that case to make it generic, so that other
cards in the same situation can use it.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use dvb_ringbuffer instead of an own buffer implementation in
dmxdev.[ch].
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Oliver Endriss spotted, that resetting read and write pointers on
flush() requires additional locking and breaks the av7110 driver.
Therefore this patch partially reverts the previous patch titled "make
dvb_ringbuffer compatible to dmxdev_buffer".
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDEO_MXB selects VIDEO_TUNER, so we don't have to include tuner.o
in the Makefile.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx25840 module requires external firmware in order to function,
so it must select FW_LOADER, but saa7115 and saa7129 do not require it.
This patch creates VIDEO_CX25840, and alters VIDEO_DECODER to select it.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the call to cx88_core_get returns a NULL value, it is dereferenced
by cx88_reset, and perhaps by cx88_core_put. Spotted by the Coverity
checker.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added variable 'error' to struct dvb_ringbuffer, which is set to zero on
init() and flush(). Also reset read an write pointers to zero on flush()
to get less fragmented data.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes default values for some picture controls:
- brightness set to 50% by default (now is 0%)
- hue set to 50% by default (now is 0%)
- sets saturation to datasheet value
- volume set to 0dB (now is -32dB)
and some left small fixes:
- twice offset adding
- balance didn't follow datasheet (bits[0:5] = attenuation;
bit[6] = channel to provide attenuation)
Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: Ian Pickworth <ian@pickworth.me.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the IR remote control found in the card
CX88_BOARD_PROLINK_PLAYTVPVR.
Signed-off-by: Matheus Izvekov <mizvekov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch changes the gpio0 values for the card CX88_BOARD_PROLINK_PLAYTVPVR
to the ones observed using RegSpy from the dscaler project.
Signed-off-by: Matheus Izvekov <mizvekov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added support for AVerMedia A169 Dual Analog tuner card
(dual saa7134 decoders - only 1 working right now)
- Added autodetection for both parts of the card.
It shows up like 2 cards, B1 and B
- Enabled tuner B1, SVIDEO on B1 and composite1 through SVIDEO,
FIXME: B is more or less dead at this point and I suspect the
FM-radio is on the B part of the board
Signed-off-by: Rickard Osser <ricky@osser.se>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- added tuner_lg_taln_pal_secam_ranges
- renamed tuner 66 from TUNER_LG_NTSC_TALN_MINI to TUNER_LG_TALN
- updated FlyTV mini Asus Digimatrix with new tuner
Thanks-to: Rickard Osser <ricky@osser.se>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- matched indents on quotes within a printk
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some chipsets have several problems when pci to pci transfers are activated
on overlay mode. the option no_overlay allows disabling such feature of
the driver, in favor of keeping the system stable.
The default is to use pcipci_fail flag defined on drivers/pci/quirks.c.
It also allows the user to override it by forcing disable overlay or forcing
enable. Forcing enable may generate PCI transfer corruption, including disk
mass corruption, so should be used with care.
Added a text description to this option and make messages looks the same at
both bttv and saa7134 drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Used Lindent, manually changed some line breaks. Removed invalid email
addresses, useless casts and useless initialization of return values.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename 'enum dmxdevype' to 'enum dmxdev_type' and use this enum instead
of int for the member 'type' of struct dmxdev_filter.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The member dvbdev gets initialized once but is never used after that.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The PID value is already stored in struct dmx_sct_filter_params which is
a member of struct dmxdev_filter.
Acked-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Old values generally works in A2 mono, but new ones allows:
- detect and use Nicam stereo
- mute in tv
- use radio FM
Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is an error in the cx88 code that causes this message in the syslog when
balance is changed at full volume:
Mar 4 18:35:08 ian2 kernel: cx88[0]: irq pci [0x1] vid*
Mar 4 18:35:39 ian2 last message repeated 348 times
Mar 4 18:36:01 ian2 last message repeated 564 times
... and so on
The attached patch cures this problem.
Signed-off-by: Ian Pickworth <ian@pickworth.me.uk>
Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Coverity checker (previously Stanford checker) noticed that
the value of nskips could be read even if it was never written.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Conflicts:
Documentation/video4linux/CARDLIST.cx88
drivers/media/video/cx88/Kconfig
drivers/media/video/em28xx/em28xx-video.c
drivers/media/video/saa7134/saa7134-dvb.c
Resolved as in the original merge by Mauro Carvalho Chehab
VIDEO_CX88_ALSA should not be between VIDEO_CX88_DVB and
VIDEO_CX88_DVB_ALL_FRONTENDS
When cx88-alsa was added to cx88/Kconfig, it was added in between
VIDEO_CX88_DVB and VIDEO_CX88_DVB_ALL_FRONTENDS. This caused
undesireable effects to the appearance of the menu options in
menuconfig.
This fix reorders cx88-alsa and cx88-dvb in Kconfig, to match saa7134,
and restore the correct menuconfig appearance.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixed em28xx based system lockup, device needs to be initialized before
starting the isoc transfer otherwise the system will completly lock up.
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The behaviour of the all-in-one Video4Linux tuner driver apparently
changed. It now wants to know the tv standard, otherwise it refuses to
tune.
Restore tuning functionality in my driver for the "Multimedia eXtension
Board". The all-in-one tuner driver apparently changed its behaviour.
Signed-off-by: Michael Hunold <hunold@linuxtv.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
