Since commit e58aa3d2d0 ("genirq: run irq handlers with interrupts
disabled") we run all interrupt handlers with interrupts disabled and we
even check and yell when an interrupt handler returns with interrupts
enabled - see commit b738a50a20 ("genirq: warn when handler enables
interrupts").
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Following changes are made as part of this change:
1. As TWL RTC supports periodic interrupt, the correct event should be
RTC_PF instead of RTC_UF.
2. No need to initialize variable "events" to 0 & then OR it with the
event values. Hence fixing it.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For clearing RTC interrupt, programming ALARM bit only is sufficient, as
all other bits are any way not affected by writing 0 to them.
Hence removed unwanted OR operation.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As part of probe, before enabling RTC, RTC_CTRL register is read to check
if it is already running. If RTC is used by kernel alone, then this read
is not required. Even if RTC was enabled already by boot loader, setting
STOP_RTC bit again should not harm. Hence removed unwanted read
operation.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the TWL RTC driver has a cached copy of enabled RTC interrupt bits in
variable rtc_irq_bits, that can be checked before really setting or
masking any of the interrupt bits.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Factor out some boilerplate code for spi driver registration into
module_spi_driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Mark Jackson <mpfj@mimc.co.uk>
Cc: Dennis Aberilla <denzzzhome@yahoo.com>
Cc: Nikolaus Voss <n.voss@weinmann.de>
Cc: "Kim B. Heino" <Kim.Heino@bluegiga.com>
Cc: Raphael Assenat <raph@raphnet.net>
Cc: Chris Verges <chrisv@cyberswitching.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc_device_register() calls rtc-spear routines internally. These
routines call dev_get_drvdata() to get struct spear_rtc_config.
Currently, platform_set_drvdata is called after rtc device is
registered. This causes system to crash, as dev_get_drvdata returns
NULL.
For this we need to call platform_set_drvdata() before registering rtc
device. This requires further cleanup, that leads to removal of
dev_set_drvdata on rtc->dev, which was just not required at all.
Also, we change the parameter to request_irq and pass pointer to config
instead of pointer to rtc struct.
This patch brings all above changes.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Deepak Sikri <deepak.sikri@st.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define API for '.alarm_irq_enable' to enable and disable alarm irq. This
is required by the framework else RTC_AIE_ON and RTC_AIE_OFF ioctls
return errors.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Deepak Sikri <deepak.sikri@st.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle the fix for unbalanced irq for the cases when enable_irq_wake
fails, and a warning related to same is displayed on the console. The
workaround is handled at the driver level.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
arch/arm/mach-lpc32xx/clock.c
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
The conflicts with pxa are non-obvious, we have multiple branches
adding and removing the same clock settings. According to
Haojian Zhuang, removing the sa1100 rtc dummy clock is the correct
fix here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull timer changes for v3.4 from Ingo Molnar
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
ntp: Fix integer overflow when setting time
math: Introduce div64_long
cs5535-clockevt: Allow the MFGPT IRQ to be shared
cs5535-clockevt: Don't ignore MFGPT on SMP-capable kernels
x86/time: Eliminate unused irq0_irqs counter
clocksource: scx200_hrt: Fix the build
x86/tsc: Reduce the TSC sync check time for core-siblings
timer: Fix bad idle check on irq entry
nohz: Remove ts->Einidle checks before restarting the tick
nohz: Remove update_ts_time_stat from tick_nohz_start_idle
clockevents: Leave the broadcast device in shutdown mode when not needed
clocksource: Load the ACPI PM clocksource asynchronously
clocksource: scx200_hrt: Convert scx200 to use clocksource_register_hz
clocksource: Get rid of clocksource_calc_mult_shift()
clocksource: dbx500: convert to clocksource_register_hz()
clocksource: scx200_hrt: use pr_<level> instead of printk
time: Move common updates to a function
time: Reorder so the hot data is together
time: Remove most of xtime_lock usage in timekeeping.c
ntp: Add ntp_lock to replace xtime_locking
...
For simple modules that contain a single amba_driver without any
additional setup code then ends up being a block of duplicated
boilerplate. This patch adds a new macro, module_amba_driver(),
which replaces the module_init()/module_exit() registrations with
template functions.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* spear/dt:
ARM: SPEAr600: Add device-tree support to SPEAr600 boards
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-spear6xx/spear6xx.c
arch/arm/mach-vexpress/Kconfig
The conflicts are between the previous contents of the next/dt2
branch and upstream changes from v3.3-rc7.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'kirkwood_dt_for_3.4_v3' of git://git.infradead.org/users/jcooper/linux-kirkwood:
ARM: kirkwood: use devicetree for rtc-mv
ARM: kirkwood: rtc-mv devicetree bindings
ARM: kirkwood: fdt: define uart[01] as disabled, enable uart0
ARM: kirkwood: fdt: facilitate new boards during fdt migration
ARM: kirkwood: fdt: absorb kirkwood_init()
ARM: kirkwood: fdt: use mrvl ticker symbol
ARM: orion: wdt: use resource vice direct access
ARM: Kirkwood: Remove tclk from kirkwood_asoc_platform_data.
ARM: orion: spi: remove enable_clock_fix which is not used
Richard Weinberger noticed that on some RTC hardware that
doesn't support UIE mode, due to coarse granular alarms
(like 1minute resolution), the current virtualized RTC
support doesn't properly error out when UIE is enabled.
Instead the current code queues an alarm for the next second,
but it won't fire until up to a miniute later.
This patch provides a generic way to flag this sort of hardware
and fixes the issue on the mpc5121 where Richard noticed the
problem.
CC: stable@vger.kernel.org
Reported-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: John Stultz <john.stultz@linaro.org>
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
For 88pm860x pmic, it can wake the system from low power mode by irq,
its sub-devs like RTC and onkey can be enabled for this usage.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If probing the RTC didn't succeed due to failed RTC register access, the
RTC device will be unregistered. Then, when removing the module
r9701_remove() causes a kernel crash while trying to unregister a not
registered RTC device. Fix this by doing RTC register access test before
RTC device registration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the ARCH name to "ARCH_S3C24XX" for Samsung
S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443,
and S3C2450 SoCs so that we can merge the mach-xxx directories
and plat-s3c24xx dir. to just one mach-s3c24xx for them.
I think this should be sent to upstream via samsung tree because
this touches many samsung stuff.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
[for the gadget part:]
Acked-by: Felipe Balbi <balbi@ti.com>
[for the framebuffer (video) part:]
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[For the watchdog-part:]
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Avoid to hard coded irq in rtc-sa1100 driver since we could share
it among arch-sa1100/arch-pxa/arch-mmp.
We still keep hard coded register address since the requirement is
enabling both rtc-sa1100 and rtc-pxa driver. The register addresses
are conflict since they're only two wrappers on the same rtc device.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Since next alarm time is already calculated in rtc common interface, we
needn't keep this logic in rtc-sa1100.c any more.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Since periodic timer is already supported by hrtimer in rtc interface,
we needn't keep the duplicated code in rtc-sa1100.c any more.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
The GPBR registers are used for storing RTC values. The GPBR registers
to use are now provided using standard resource entry. The array is
filled in SoC specific code.
rtc-at91sam9 RTT as RTC driver is modified to retrieve this information.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: rework resources assignment]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Instead of computing virtual address with AT91_VA_BASE_SYS, use the
appropriate ioremap() call on the driver "memory" resource.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
For the RTT as RTC driver rtc-at91sam9, the platform_device structure
is filled during SoC initialization. This will allow to convert this
RTC driver as a standard platform driver.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* lpc32xx/drivers: (566 commits)
ARM: LPC32xx: ADC support for mach-lpc32xx
Includes an update to Linux 3.3-rc4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Instead of computing virtual address with AT91_VA_BASE_SYS, use the
appropriate ioremap() call on the driver "memory" resource.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Especially the TICNT registers are different from the two rtc
types that currently exists.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use the data field of of_device_id to hold the type for
s3c_cpu_type.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Currently, the RTC code does not disable the alarm in the hardware.
This means that after a sequence such as the one below (the files are in the
RTC sysfs), the box will boot up after 2 minutes even though we've
asked for the alarm to be turned off.
# echo $((`cat since_epoch`)+120) > wakealarm
# echo 0 > wakealarm
# poweroff
Fix this by disabling the alarm when there are no timers to run.
The original version of this patch was reverted. This version
disables the irq directly instead of setting a disabled timer
in the future.
Cc: stable@kernel.org
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Merged in the second revision from Rabin]
Signed-off-by: John Stultz <john.stultz@linaro.org>
If the alarm time programming in the rtc is ever in the past, it won't fire,
and any other alarm will be queued after it so they won't fire either.
So any time that the alarm might be in the past, we need to trigger
the irq handler to ensure the old alarm is cleared and the timer queue
is fully in the future.
This is done whenever the RTC clock is set.
This is the second revision of this patch, which was earlier reverted.
This version avoids the initialization problem, which is handled by
a different patch.
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: NeilBrown <neilb@suse.de>
[Remove problematic initialization change, update commit log, also
catch set_mmss case -jstultz]
Signed-off-by: John Stultz <john.stultz@linaro.org>
In some cases at boot up, the RTC alarm may be set in the past,
but still have the enabled flag on. This was causing problems,
because we would then enqueue the alarm into the timerqueue,
but it would never fire. This would clog up the timerqueue
and keep other alarms from working.
The fix is to check the alarm against the current rtc time at
boot and avoid enqueueing the alarm if it is in the past.
Reported-by: NeilBrown <neilb@suse.de>
Tested-by: NeilBrown <neilb@suse.de>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This reverts commit 42874759d7.
This wasn't tested as a stand-alone patch, and it has build errors
without the following patches applied:
drivers/rtc/rtc-sa1100.c: In function 'sa1100_rtc_set_alarm':
drivers/rtc/rtc-sa1100.c:208: error: 'now' undeclared (first use in this function)
drivers/rtc/rtc-sa1100.c:208: error: (Each undeclared identifier is reported only once
drivers/rtc/rtc-sa1100.c:208: error: for each function it appears in.)
drivers/rtc/rtc-sa1100.c:210: error: incompatible type for argument 3 of 'rtc_next_alarm_time'
drivers/rtc/rtc-sa1100.c:211: error: 'time' undeclared (first use in this function)
So it too gets reverted to bring us back to a working point.
This reverts commit 7cea00657d.
The sa1100 cleanups fatally broke the SA1100 RTC driver - the first
hint that something is wrong are these compiler warnings:
drivers/rtc/rtc-sa1100.c:42:1: warning: "RCNR" redefined
In file included from arch/arm/mach-sa1100/include/mach/hardware.h:73,
from drivers/rtc/rtc-sa1100.c:35:
arch/arm/mach-sa1100/include/mach/SA-1100.h:877:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:43:1: warning: "RTAR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:876:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:44:1: warning: "RTSR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:879:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:45:1: warning: "RTTR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:878:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:47:1: warning: "RTSR_HZE" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:891:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:48:1: warning: "RTSR_ALE" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:890:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:49:1: warning: "RTSR_HZ" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:889:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:50:1: warning: "RTSR_AL" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:888:1: warning: this is the location of the previous definition
and the second problem, which is far more severe, are the different
register layouts, resulting in the wrong registers being read on
SA11x0 platforms. This patch adds:
#define RCNR 0x00 /* RTC Count Register */
#define RTAR 0x04 /* RTC Alarm Register */
#define RTSR 0x08 /* RTC Status Register */
#define RTTR 0x0c /* RTC Timer Trim Register */
but the SA11x0 registers are:
#define RTAR __REG(0x90010000) /* RTC Alarm Reg. */
#define RCNR __REG(0x90010004) /* RTC CouNt Reg. */
#define RTTR __REG(0x90010008) /* RTC Trim Reg. */
#define RTSR __REG(0x90010010) /* RTC Status Reg. */
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel config: Fix the APB_TIMER selection
x86/mrst: Add additional debug prints for pb_keys
x86/intel config: Revamp configuration to allow for Moorestown and Medfield
x86/intel/scu/ipc: Match the changes in the x86 configuration
x86/apb: Fix configuration constraints
x86: Fix INTEL_MID silly
x86/Kconfig: Cyclone-timer depends on x86-summit
x86: Reduce clock calibration time during slave cpu startup
x86/config: Revamp configuration for MID devices
x86/sfi: Kill the IRQ as id hack
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") introduced a
potential infinite loop. If an alarm time contains a wildcard month and
an invalid day (> 31), or a wildcard year and an invalid month (>= 12),
the loop searching for the next matching date will never terminate. Treat
the invalid values as wildcards.
Fixes <http://bugs.debian.org/646429>, <http://bugs.debian.org/653331>
Reported-by: leo weppelman <leoweppelman@googlemail.com>
Reported-by: "P. van Gaans" <mailme667@yahoo.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
