SBC-3 mandates the protection checks that must be
performed in the rdprotect/wrprotect field. Use them.
According to backstore device pi_attributes and
cdb rdprotect/wrprotect field.
(Fix incorrect se_cmd->prot_type -> TARGET_PROT_NORMAL
comparision in transport_generic_new_cmd - nab)
(Fix missing break in sbc_set_prot_op_checks - DanC + Sagi)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The CMD_T_FAILED flag is set used in one place to record the result of a
trivial test, and it is only tested once, few lines later. We might as
well make the code simpler and easier to read by directly doing the test
of "success" where we want to use it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- add support for SCSI Referrals (Hannes)
- add support for T10 DIF into target core (nab + mkp)
- add support for T10 DIF emulation in FILEIO + RAMDISK backends (Sagi + nab)
- add support for T10 DIF -> bio_integrity passthrough in IBLOCK backend (nab)
- prep changes to iser-target for >= v3.15 T10 DIF support (Sagi)
- add support for qla2xxx N_Port ID Virtualization - NPIV (Saurav + Quinn)
- allow percpu_ida_alloc() to receive task state bitmask (Kent)
- fix >= v3.12 iscsi-target session reset hung task regression (nab)
- fix >= v3.13 percpu_ref se_lun->lun_ref_active race (nab)
- fix a long-standing network portal creation race (Andy)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
target: Fix percpu_ref_put race in transport_lun_remove_cmd
target/iscsi: Fix network portal creation race
target: Report bad sector in sense data for DIF errors
iscsi-target: Convert gfp_t parameter to task state bitmask
iscsi-target: Fix connection reset hang with percpu_ida_alloc
percpu_ida: Make percpu_ida_alloc + callers accept task state bitmask
iscsi-target: Pre-allocate more tags to avoid ack starvation
qla2xxx: Configure NPIV fc_vport via tcm_qla2xxx_npiv_make_lport
qla2xxx: Enhancements to enable NPIV support for QLOGIC ISPs with TCM/LIO.
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
IB/isert: pass scatterlist instead of cmd to fast_reg_mr routine
IB/isert: Move fastreg descriptor creation to a function
IB/isert: Avoid frwr notation, user fastreg
IB/isert: seperate connection protection domains and dma MRs
tcm_loop: Enable DIF/DIX modes in SCSI host LLD
target/rd: Add DIF protection into rd_execute_rw
target/rd: Add support for protection SGL setup + release
target/rd: Refactor rd_build_device_space + rd_release_device_space
target/file: Add DIF protection support to fd_execute_rw
target/file: Add DIF protection init/format support
...
This patch fixes a percpu_ref_put race for se_lun->lun_ref in
transport_lun_remove_cmd() where ->lun_ref could end up being
put more than once per command via different target completion
and fabric release contexts.
It adds a cmpxchg() for se_cmd->lun_ref_active to ensure that
percpu_ref_put() is only ever called once per se_cmd.
This bug was manifesting itself as a LUN shutdown regression
bug in >= v3.13 code, where percpu_ref_kill() would end up
hanging indefinately due to the incorrect percpu_ref count.
(Change se_cmd->lun_ref_active from bool -> int to force at
least a 4-byte cmpxchg with MIPS ll/sc ins. - Fengguang)
Reported-by: Tommy Apel <tommyapeldk@gmail.com>
Cc: Tommy Apel <tommyapeldk@gmail.com>
Cc: <stable@vger.kernel.org> #3.13+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SPC-4 states that data-integrity errors shall also report
the failed sector in CHECK_CONDITION response sense data
information field.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for DIF related CHECK_CONDITION ASC/ASCQ
exception cases into transport_send_check_condition_and_sense().
This includes:
LOGICAL BLOCK GUARD CHECK FAILED
LOGICAL BLOCK APPLICATION TAG CHECK FAILED
LOGICAL BLOCK REFERENCE TAG CHECK FAILED
that used by DIF TYPE1 and TYPE3 failure cases.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds DIF related definitions to target_core_base.h
that includes enums for target_prot_op + target_prot_type +
target_prot_version + target_guard_type + target_pi_error.
Also included is struct se_dif_v1_tuple, along with changes
to struct se_cmd, struct se_dev_attrib, and struct se_device.
Also, add new se_subsystem_api->[init,format,free]_prot() callers
used by target core code to setup backend specific protection
information after the device has been configured.
Enums taken from Sagi Grimberg's original patch.
v2 changes:
- Drop guard_type related definitions
- Update target_prot_op + target_prot_ho definitions (Sagi)
- Drop SCF_PROT + pi_prot_version flag
- Add se_subsystem_api->format_prot() (Sagi)
- Add hw_pi_prot_type device attribute
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the temporary buffer in spc_emulate_inquiry() to
use dynamically allocated memory, instead of local stack memory.
Also bump SE_INQUIRY_BUF up to 1024 bytes to be safe when handling
multiple large SCSI name descriptors for EVPD=0x83.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add infrastructure for referrals.
v2 changes:
- Fix unsigned long long division in core_alua_state_lba_dependent on
32-bit (Fengguang + Chen + Hannes)
- Fix compile warning in core_alua_state_lba_dependent (nab)
- Convert segment_* + sectors variables in core_alua_state_lba_dependent
to u64 (Hannes)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch allows FILEIO to update hw_max_sectors based on the current
max_bytes_per_io. This is required because vfs_[writev,readv]() can accept
a maximum of 2048 iovecs per call, so the enforced hw_max_sectors really
needs to be calculated based on block_size.
This addresses a >= v3.5 bug where block_size=512 was rejecting > 1M
sized I/O requests, because FD_MAX_SECTORS was hardcoded to 2048 for
the block_size=4096 case.
(v2: Use max_bytes_per_io instead of ->update_hw_max_sectors)
Reported-by: Henrik Goldman <hg@x-formation.com>
Cc: <stable@vger.kernel.org> #3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We should be including a descriptor referring to the target device
to allow identification of different TCM instances.
(nab: Bump SE_INQUIRY_BUF to 1024 bytes to handle 2x 256 byte SCSI names)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use a workqueue for processing ALUA state transitions; this allows
us to process implicit delay properly.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
During state transition we should be storing both the original
and the pending state.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We should only allocate ALUA metadata if we're actually going
to write them.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Commit 04f3b31bff ("iscsi-target: Convert iscsi_session statistics to
atomic_long_t") removed the updating of these fields in iscsi (the only
fabric driver that ever touched these counters), and the core has no way
to report or otherwise use the values. Remove the last remnants of
these counters.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The supported ALUA states might be different for individual
devices, so store it in a separate field.
(nab: Remove unnecessary line continuation)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the handful of se_device statistics to type
atomic_long_t, instead of using se_device->stats_lock when
incrementing these values.
More importantly, go ahead and drop the spinlock usage within
transport_lookup_cmd_lun() fast-path code.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a se_device->xcopy_lun that is used for local
copy offload I/O, instead of allocating + initializing a pseudo
se_lun for each received EXTENDED_COPY operation.
Also, move declaration of struct se_lun + struct se_port_stat_grps
ahead of struct se_device.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now with percpu refcounting for se_lun in place, go ahead and drop
the legacy per se_cmd accounting for se_lun shutdown.
This includes __transport_clear_lun_from_sessions(), the associated
transport_lun_wait_for_tasks() logic, along with a handful of now
unused se_cmd structure members and ->transport_state bits.
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds percpu refcounting for se_lun access that allows the
association of an se_lun + se_cmd in transport_lookup_cmd_lun() to
occur without an extra list_head for tracking outstanding I/O during
se_lun shutdown.
This effectively changes se_lun shutdown logic to wait for outstanding
I/O percpu references to complete in transport_lun_remove_cmd() using
se_lun->lun_ref_comp, instead of explicitly draining the per se_lun
command list and waiting for individual se_cmd descriptor processing
to complete.
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the Third Party Copy (3PC) bit to signal support
for EXTENDED_COPY within standard inquiry response data.
Also add emulate_3pc device attribute in configfs (enabled by default)
to allow the exposure of this bit to be disabled, if necessary.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds support for EXTENDED_COPY emulation from SPC-3, that
enables full copy offload target support within both a single virtual
backend device, and across multiple virtual backend devices. It also
functions independent of target fabric, and supports copy offload
across multiple target fabric ports.
This implemenation supports both EXTENDED_COPY PUSH and PULL models
of operation, so the actual CDB may be received on either source or
desination logical unit.
For Target Descriptors, it currently supports the NAA IEEE Registered
Extended designator (type 0xe4), which allows the reference of target
ports to occur independent of fabric type using EVPD 0x83 WWNs.
For Segment Descriptors, it currently supports copy from block to
block (0x02) mode.
It also honors any present SCSI reservations of the destination target
port. Note that only Supports No List Identifier (SNLID=1) mode is
supported.
Also included is basic RECEIVE_COPY_RESULTS with service action type
OPERATING PARAMETERS (0x03) required for SNLID=1 operation.
v3 changes:
- Fix incorrect return type in target_do_receive_copy_results()
(Fengguang)
v2 changes:
- Use target_alloc_sgl() instead of transport_generic_get_mem()
- Convert debug output to use pr_debug()
- Convert target_xcopy_parse_target_descriptors() NAA IEEN WWN
dump to use 0x%16phN format specification
- Drop unnecessary xcopy_pt_cmd->xpt_passthrough_wsem, and
associated usage in xcopy_pt_write_pending() and
target_xcopy_issue_pt_cmd()
- Add check for unsupported EXTENDED_COPY(LID4) service action
bits in target_do_xcopy()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
EXTENDED_COPY needs to be able to search a global list of devices
based on NAA WWN device identifiers, so add a simple g_device_list
protected by g_device_mutex.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds support for COMPARE_AND_WRITE emulation on a per block
basis. This logic is used as an atomic test and set primative currently
used by VMWare ESX VAAI for performing array side locking of individual
VMFS extent ownership.
This includes the COMPARE_AND_WRITE CDB parsing within sbc_parse_cdb(),
and does the majority of the work within the compare_and_write_callback()
to perform the verify instance user data comparision, and subsequent
write instance user data I/O submission upon a successfull comparision.
The synchronization is enforced by se_device->caw_sem, that is obtained
before the initial READ I/O submission in sbc_compare_and_write(). The
mutex is then released upon MISCOMPARE in compare_and_write_callback(),
or upon WRITE instance user-data completion in compare_and_write_post().
The implementation currently assumes a single logical block (NoLB=1).
v4 changes:
- Explicitly clear cmd->transport_complete_callback for two failure
cases in sbc_compare_and_write() in order to avoid double unlock
of ->caw_sem in compare_and_write_callback() (Dan Carpenter)
v3 changes:
- Convert se_device->caw_mutex to ->caw_sem
v2 changes:
- Set SCF_COMPARE_AND_WRITE and cmd->execute_cmd() to
sbc_compare_and_write() during setup in sbc_parse_cdb()
- Use sbc_compare_and_write() for initial READ submission with
DMA_FROM_DEVICE
- Reset cmd->execute_cmd() to sbc_execute_rw() for write instance
user-data in compare_and_write_callback()
- Drop SCF_BIDI command flag usage
- Set TRANSPORT_PROCESSING + transport_state flags before write
instance submission, and convert to __target_execute_cmd()
- Prevent sbc_get_size() from being being called twice to
generate incorrect size in sbc_parse_cdb()
- Enforce se_device->caw_mutex synchronization between initial
READ I/O submission, and final WRITE I/O completion.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds the MAXIMUM COMPARE AND WRITE LENGTH bit, currently
hardcoded to a single logical block (NoLB=1) within the Block Limits
VPD in spc_emulate_evpd_b0().
Also add emulate_caw device attribute in configfs (enabled by default)
to allow the exposure of this bit to be disabled, if necessary.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
After COMPARE_AND_WRITE completes it's comparision, the WRITE
payload SGLs head expect to be updated to point from the verify
instance of user data, to the write instance of user data.
So for this special case, add transport_reset_sgl_orig() usage
within transport_free_pages() and add se_cmd->t_data_[sg,nents]_orig
members to save the original assignments.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
COMPARE_AND_WRITE expects to be able to send down a DMA_FROM_DEVICE
to obtain the necessary READ payload for comparision against the
first half of the WRITE payload containing the verify user data.
Currently virtual backends expect to internally reference SGLs,
SGL nents, and data_direction, so change IBLOCK, FILEIO and RD
sbc_ops->execute_rw() to accept this values as function parameters.
Also add default sbc_execute_rw() handler for the typical case for
cmd->execute_rw() submission using cmd->t_data_sg, cmd->t_data_nents,
and cmd->data_direction).
v2 Changes:
- Add SCF_COMPARE_AND_WRITE command flag
- Use sbc_execute_rw() for normal cmd->execute_rw() submission
with expected se_cmd members.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds TCM_MISCOMPARE_VERIFY (ASC=0x1d, ASCQ=0x00) sense
handling to transport_send_check_condition_and_sense(), which is
required for a COMPARE_AND_WRITE comparision failure.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds a sense_reason_t return to ->transport_complete_callback(),
and updates target_complete_ok_work() to invoke the call if necessary to
transport_send_check_condition_and_sense() during the failure case.
Also update xdreadwrite_callback() to use this return value.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds lib/idr.c based transport_init_session_tags() logic
that allows fabric drivers to setup a per-cpu se_sess->sess_tag_pool
and associated se_sess->sess_cmd_map for basic tagged pre-allocation
of fabric descriptor sized memory.
v5 changes:
- Convert to percpu_ida.h include
v4 changes:
- Add transport_alloc_session_tags() for fabrics that need early
transport_init_session()
v3 changes:
- Update to percpu-ida usage
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Asias He <asias@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Three have been checked for but were never set. Remove the dead code.
Also renumbers the remaining ones to a) get rid of the holes after the
removal and b) avoid a collision between TMR_FUNCTION_COMPLETE==0 and
the uninitialized case. If we failed to set a code, we should rather
fall into the default case then return success.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an optional /auth/ configfs group to TPG context that
can be used by fabrics like iscsi-target for TPG demo-mode
authentication.
Cc: Dax Kelson <dkelson@gurulabs.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now with iscsi-target using modern se_cmd->cmd_kref accounting in
v3.10 code, it's safe to go ahead and drop the legacy release
codepath + se_cmd->check_release bit in transport_release_cmd()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes legacy se_cmd->t_fe_count usage in order to avoid
se_cmd->t_state_lock access within transport_put_cmd() during normal
fast path se_cmd descriptor release.
Also drop the left-over parameter usage within core_tmr_handle_tas_abort()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of taking the buffer and length, update_and_write_aptpl() will
allocate the buffer as needed, and then free it. Instead, the function
takes an 'aptpl' boolean parameter.
This enables us to remove memory alloc/frees from struct
t10_pr_registration and other spots.
There is a slight loss of functionality because each callsite doesn't get
its own pr_debug any more, but this info can be cleaned via ftrace if
necessary and I think the shorter code is worth it.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's only ever set to PR_APTPL_BUF_LEN, so we don't need a variable.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Switch back to pre commit 1c7b13fe65 list splicing logic for active I/O
shutdown with tcm_qla2xxx + ib_srpt fabrics.
The original commit was done under the incorrect assumption that it's safe to
walk se_sess->sess_cmd_list unprotected in target_wait_for_sess_cmds() after
sess->sess_tearing_down = 1 has been set by target_sess_cmd_list_set_waiting()
during session shutdown.
So instead of adding sess->sess_cmd_lock protection around sess->sess_cmd_list
during target_wait_for_sess_cmds(), switch back to sess->sess_wait_list to
allow wait_for_completion() + TFO->release_cmd() to occur without having to
walk ->sess_cmd_list after the list_splice.
Also add a check to exit if target_sess_cmd_list_set_waiting() has already
been called, and add a WARN_ON to check for any fabric bug where new se_cmds
are added to sess->sess_cmd_list after sess->sess_tearing_down = 1 has already
been set.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Some were incremented, but never used anywhere from what I could tell.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SBC-3 (revision 35) says:
The PARAMETER LIST LENGTH field specifies the length in bytes of the
UNMAP parameter list that is available to be transferred from the
Data-Out Buffer. If the parameter list length is greater than zero
and less than 0008h (i.e., eight), then the device server shall
terminate the command with CHECK CONDITION status with the sense key
set to ILLEGAL REQUEST and the additional sense code set to
PARAMETER LIST LENGTH ERROR. A PARAMETER LIST LENGTH set to zero
specifies that no data shall be sent.
so our sense code for too-short descriptors was wrong, and we were
incorrectly failing commands that didn't transfer any descriptors.
While we're at it, also handle the UNMAP check:
If the ANCHOR bit is set to one, and the ANC_SUP bit in the Logical
Block Provisioning VPD page (see 6.6.4) is set to zero, then the
device server shall terminate the command with CHECK CONDITION
status with the sense key set to ILLEGAL REQUEST and the additional
sense code set to INVALID FIELD IN CDB.
(chris boot: Fix wrong cut+paste comment in transport_send_check_condition_and_sense)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes LIO to use the configfs backend device name as the
model if you echo '1' to an individual device's emulate_model_alias attribute.
This is a valid operation only on devices with an export count of 0.
Signed-off-by: Tregaron Bayly <tbayly@bluehost.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
"buf" is 128 characters and "vpd->device_identifier" is 256. It makes
the static checkers complain.
Also bump VPD_TMP_BUF_SIZE to match INQUIRY_VPD_DEVICE_IDENTIFIER_LEN.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Introduce TCM_NO_SENSE, mapping to sense code
'Not ready, no additional sense information'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Nicholas Bellinger <nab@risingtidesystems.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Thanks for reviews, looking a lot better.
---- 8< ----
Initiator access config could be easier. The way other storage vendors
have addressed this is to support initiator groups: the admin adds
initiator WWNs to the group, and then LUN permissions can be granted for
the entire group at once.
Instead of changing ktarget's configfs interface, this patch keeps
the configfs interface per-initiator-wwn and just adds a 'tag' field
for each. This should be enough for user tools like targetcli to group
initiator ACLs and sync their configurations.
acl_tag is not used internally, but needs to be kept in configfs so that
all user tools can avoid dependencies on each other.
Code tested to work, although userspace pieces still to be implemented.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds [dev,lun]_link_magic value assignment + checks within generic
target_fabric_port_link() and target_fabric_mappedlun_link() code to ensure
destination config_item *target_item sent from configfs_symlink() ->
config_item_operations->allow_link() is the underlying se_device->dev_group
and se_lun->lun_group that we expect to symlink.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
