Add a common entry-macro-vic2.S for systems where there are two VICs
so that the machine or platform directories just need to setup the
correct information before including <asm/entry-macro-vic2.S> into
their own entry-macro.S file.
Since this code is from the S3C64XX project, we update the S3C64XX
machine entry code to use this new header.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the handling for the UART interrupts out of the s3c64xx specific
code and into plat-samsung so that it can be used by all implementations
that need it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the VIC based timer interrupt handling out of plat-s3c64xx and
into plat-samsung to be re-used for other systems. This also reduces
the code size as we now have a common init routine and use the irq_desc
to store the interrupt number of the timer.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The arch/arm/plat-s3c/gpio-config.c file is common to pretty much all the Samsung
SoCs, so move it to arch/arm/plat-samsung
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch makes clk_default_setrate and clk_ops_def_setrate available
to code outside plat-samsung clock code.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If there is no source register defined, do not register a clksrc
clock with a valid .set_parent in the ops.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add s3c_register_clocks() to register an array of clocks, printing
an error message if there is a problem. Replace all points in the code
where this could be used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If the reg_div field is not set, then do not register clk_ops with the
get/set/round rate calls as these will fail to work.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is the core implementation of the clock code for all Samsung based
SoCs, so move it to arch/arm/plat-samsung (the clock.h file has already
been moved).
Since the file is built for every Samsung SoC, no changes are needed to the
Kconfig system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The new code calls the clock setup code on registration which
can be before the clock system has been fully initialised. The
following code re-does this setup at the end of the clock
registration and thus we get two printings.
Update the calls to only print on the last pass or when doing
the necessary resume work.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change these two fields to have named initialisers as per the
review comments from Kyungmin Park.
sed used:
s@\.reg_src\(.*\)=\(.*\){\(.*\),\(.*\),\(.*\)}@.reg_src\1=\2{ .reg =\3, .shift =\4, .size =\5 }@g
s@\.reg_div\(.*\)=\(.*\){\(.*\),\(.*\),\(.*\)}@.reg_div\1=\2{ .reg =\3, .shift =\4, .size =\5 }@g
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Reduce the size of struct clk by 12 bytes and make defining clocks with
common implementation functions easier by moving the set_rate, get_rate,
round_rate and set_parent calls into a new structure called 'struct clk_ops'
and using that instead.
This change does make a few clocks larger as they need their own clk_ops,
but this is outweighed by the number of clocks with either no ops or having
a common set of ops.
Update all the users of this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Clean out the definitions we are no longer using after the new clock
code updates.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
[ben-linux@fluff.org: split from initial patch provided]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the s3c6400-clock.c implementation over to use the new common
plat-samsung based clock-clksrc.c.
Note, this does not delete the clocks definitions that are now unused
in the regs-clock.h to reduce the quantity of change in this commit.
Based on original patches by Harald Welte.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a core for the clksrc clock implementation, which is found in many of
the newer Samsung SoCs into plat-samsung.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
[ben-linux@fluff.org: split from original patch to make change smaller]
[ben-linux@fluff.org: split clk and clksrc changes]
[ben-linux@fluff.org: moved to plat-samsung from plat-s3c]
[ben-linux@fluff.org: re-wrote headers after splits]
[ben-linux@fluff.org: added better documentation to headers]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The individually named clocks are all static to the code
and thus can be compressed into a single array and then
the array can be referenced. This removes the need for
a seperate array of pointers to clocks.
Fix a minor problem of re-initialising the pointers in
s3c6400_set_clksrc() as this is also called by the cpufreq
code. Move these initialisations to the code that does the
registration.
Based on Harald Welte's original clock changes patch.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the four fields from clksrc_clk.clk which are always the same
and init them when the clock is registered. This helps remove the amount
of repeated code.
This is a re-work of Harald Welte's clock changes for the latest kernel.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the <plat/clock.h> header to plat-samsung where it can be used by all
the platforms, and readies it for the next round of clock updates where
the clock code will be amalgamated.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove some of the __initdata tags which are currently inappropriate for
platform_device and some of the platform data. These can be returned once
support for copying platform devices and data is added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch fix mini2440 crash on boot due to improper __initdata
qualifier on mini2440_led1_pdata.
Signed-off-by: Uri Yosef <uri.yosef@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since the fixed voltage regulator grew support for GPIO based
enables and GPIO 0 is valid on some systems we need to specify
that there is no valid GPIO enable control.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since the structure field nr_map is optional, we need to check whether the
chip number map is provided to avoid unexpected NULL pointer exception.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options
ARM: Fix wrong dmb
ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock
ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards
ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h
ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes
ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set
ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code"
ARM: 5867/1: Update U300 defconfig
ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs
[ARM] pxa: fix strange characters in zaurus gpio .desc
ARM: add missing recvmmsg syscall number
[ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*()
[ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *'
[ARM] pxa: enable L2 if present in XSC3
[ARM] pxa: do not enable L2 after MMU is enabled
A kernel with both ARMv6 and ARMv7 selected results in build errors.
Fix this by specifying the proper architectures for these assembly
files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The __kuser_cmpxchg code uses an ARMv6 dmb instruction, rather than
one based upon the architecture being built for. Switch to using
the macro provided for this purpose, which also eliminates the
need for an ifdef.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- changes to ach/arch/boot/Makefile to make it easier to add new
compression types
- new piggy.lzo.S necessary for lzo compression
- changes in arch/arm/boot/compressed/misc.c to allow the use of lzo or
gzip, depending on the config
- Kconfig support
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes it consistent with the extern declaration, used when CONFIG_HIGHMEM
is set Removes redundant casts in printout messages
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extend the patch from Philby John to the other "RealView" boards.
Rename the constants and offsets to reflect their actual functions.
Cc: Philby John <pjohn@in.mvista.com>
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The file arch/arm/include/asm/cpu.h needs to include 'linux/cpu.h' to
meet its dependency. Otherwise when using "struct cpuinfo_arm" and
including just 'asm/cpu.h' throws below error -
arch/arm/include/asm/cpu.h:16: error: field 'cpu' has incomplete type
To fix this otherway, one can also include both linux/cpu.h and
asm/cpu.h but it shoudn't be that way. So this patch fixes this by
including the linux/cpu.h in asm/cpu.h, so that including alone
asm/cpu.h is enough.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a build failure [1] due to missing includes
This should make the arm tree build again with lpd7a404_defconfig
References:
http://kisskb.ellerman.id.au/kisskb/buildresult/1983329/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A lot of ARM-defconfigs (those without CONFIG_ISA_DMA_API set) fail to
build [1][2][3] due to the changes of the patch
[PATCH] PCI: Clean up build for CONFIG_PCI_QUIRKS unset
by Rafael J. Wysocki (Sat, 2 Jan 2010 22:57:24 +0100) [4]
as the referenced variable 'isa_dma_bridge_buggy' in asm/dma.h is
enclosed by the CONFIG_ISA_DMA_API conditional all configs without this
setting fail to build.
I'm not sure wether moving the condition is the right way to solve the
issue, but atleast it fixes the issue :)
References:
[1] http://kisskb.ellerman.id.au/kisskb/buildresult/1983354/
[2] http://kisskb.ellerman.id.au/kisskb/buildresult/1983333/
[3] http://kisskb.ellerman.id.au/kisskb/buildresult/1983337/
[4] http://lkml.org/lkml/2010/1/2/102
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dynamically allocate the CPUFreq frequency table on OMAP2xxx chips.
This fixes some compilation problems, since the kernel may not know
what chip it is running on until boot-time. This also reduces the size
of the CPUFreq frequency table.
Problem originally reported by Felipe Balbi <felipe.balbi@nokia.com>.
Thanks also for comments on the patch from Felipe and Kevin.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
A subsequent patch adds code on OMAP2xxx to dynamically allocate the
CPUFreq frequency table in clk_init_cpufreq_table(), so for it to
avoid a leak, it will need a corresponding function to free the
memory. This patch adds clk_exit_cpufreq_table() with generic
code to call a chip-specific variant inside the clockfw_lock spinlock via
struct clk_functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Revise some of the comments in the OMAP2xxx OPP data for clarity.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
if we enable CPUFREQ we can't build omap2 for two reasons,
one of them is fixed by the patch below.
It's failing because the __must_be_array() check in
ARRAY_SIZE() is failing and printing the following message:
arch/arm/mach-omap2/clock2xxx.c:453: error: negative width in bit-field '<anonymous>'
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
[paul@pwsan.com: commit message updated; changed rate variable name]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 52650505fb added an __initdata
decoration to the structure containing the clk_enable and clk_disable
functions. Once init data was freed, these pointers went to null, and
the next enable or disable call caused the kernel to crash. This
change removes this decoration.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
[paul@pwsan.com: patch manually split and commit message edited]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This change adds in some missing clocks that were needed as a result
of 526505... (OMAP1 clock: convert mach-omap1/clock.h to
mach-omap1/clock_data.c). Prior to this, it was just assumed that
these clocks existed for all devices, and it was used directly instead
of calling it out with a clock_get call or similar. So, not having
the CK_7XX meant these clocks weren't being used anymore for omap 7xx
devices, which broke things badly.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
[paul@pwsan.com: commit message edited]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The only symbols that should be exported are symbols that are to be
called from loadable kernel modules, e.g., device drivers. In the
context of plat-omap/clock.c, these should only be the Linux clock
interface symbols as defined by include/linux/clk.h. Core code
doesn't need these symbols to be exported. Also, clean up an old
comment while here.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add necessary definitions to clock framework to allow changing
dpll4_m5_ck rate. This is used by the camera code.
Signed-off-by: Jouni Högander <jouni.hogander@nokia.com>
Signed-off-by: Tuukka Toivonen <tuukka.o.toivonen@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The correct parent of the McBSP 2, 3, and 4 functional clocks is
PER_96M_FCLK, not CORE_96M_FCLK. Fix this in the OMAP clock tree.
Reported by Nicole Chalhoub <n-chalhoub@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Nicole Chalhoub <n-chalhoub@ti.com>
UART1 & 2 were missing clockdomains resulting in broken omap_hwmod
init for these devices.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 10db25fea4 causes the following
kernel messages during N800 boot (and presumably all other 2420
boards):
[ 0.000000] BUG: mapping for 0x58000000 at 0xe0000000 overlaps vmalloc space
[ 0.000000] BUG: mapping for 0x59000000 at 0xe1000000 overlaps vmalloc space
[ 0.000000] BUG: mapping for 0x5a000000 at 0xe2000000 overlaps vmalloc space
Fix by remapping the IVA memory areas somewhere outside vmalloc space.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Out of the three major OMAP2 chip types, OMAP2420, OMAP2430, and OMAP3430,
we only map the IVA on OMAP2420. The memory mapping is not shared between
OMAP2420 and OMAP2430, so it is inappropriate to label those macros as
'24XX'; this patch changes them to '2420'.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In OMAP2/3 some of the clock-domains which did not have control
facility were being falsely written to and read using the CM_CLKSTCTRL
register though it did not exist for them. One check is added to remove
this flaw.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Without this the kernel doesn't boot, it craches in
omap_mux_package_fixup(), since the package_subset becomes NULL.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise bringing up new boards can be harder:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
last sysfs file:
Modules linked in:
CPU: 0 Not tainted (2.6.33-rc2-00015-g0bc9c93-dirty #37)
PC is at omap_mux_init+0xa4/0x3d8
LR is at omap_mux_init+0x3c/0x3d8
...
Signed-off-by: Tony Lindgren <tony@atomide.com>
`!' has a higher precedence than `&' so parentheses are required.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Keys: 'right arrow', 'up arrow' and 'select' were mapped
wrongly. This patch corrects them.
This patch also adds one missing key present in the board,
currently I added it as 'unknown' key, as I am not able to
find proper description for this key.
One key entry (r: 7, c: 5) is present in the keymap, which
is really not present in the board, removing it.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit f62349ee97 makes it possible to
have some other than first uart port as ttyS0, which breaks the workaround
serial_in_override() function which will try to address the first uart
port (for ttyS0) and not the one that was initialized.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
CC: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 9905a43b made struct backlight_ops const. Omap was
setting check_fb dynamically, which caused the following
compile error:
drivers/video/backlight/omap1_bl.c: In function 'omapbl_probe':
drivers/video/backlight/omap1_bl.c:142: error: assignment of read-only variable 'omapbl_ops'
Turns out pdata->check_fb is not being used, so just remove
it to fix the compile.
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 35c9049b27 added
drivers/spi/omap_spi_100k.c.
This patch add the related clocks and pin muxing
entries to make the driver work on omap7xx platforms.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some chips, namely any OMAP1 chips using METHOD_MPUIO,
OMAP15xx and OMAP7xx, cannot be setup to respond to on-chip GPIO
interrupts in both rising and falling edge directions -- they can
only respond to one direction or the other, depending on how the
ICR is configured.
Additionally, current code forces rising edge detection if both
flags are specified:
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 1 << gpio;
else if (trigger & IRQ_TYPE_EDGE_FALLING)
l &= ~(1 << gpio);
else
goto bad;
This change implements a toggle function that will modify the ICR
to flip the direction of interrupt for IRQs that are requested with
both rising and falling flags. The toggle function is not called
for chips and GPIOs it does not apply to through the use of a flip_mask
that's added on a per-bank basis. The mask is only set for those
GPIOs where a toggle is necessary. Edge detection starts out the
same as above with FALLING mode first.
The toggle happens on EACH interrupt; without it, we have the
following sequence of actions on GPIO transition:
ICR GPIO Result
0x1 0 -> 1 (rising) Interrupt
0x1 1 -> 0 (falling) No interrupt
(set ICR to 0x0 manually)
0x0 0 -> 1 (rising) No interrupt
0x0 1 -> 0 (falling) Interrupt
That is, with the ICR set to 1 for a gpio, only rising edge interrupts
are caught, and with it set to 0, only falling edge interrupts are
caught. If we add in the toggle, we get this:
ICR GPIO Result
0x1 0 -> 1 (rising) Interrupt (ICR set to 0x0)
0x0 1 -> 0 (falling) Interrupt (ICR set to 0x1)
0x1 0 -> 1 ...
so, both rising and falling are caught, per the request for both
(IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING).
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In its current form, the omap_mcbsp_request() function can return after
irq_request() failure without any cleanups, effectively locking out the port
forever with clocks left running. Fix it.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following warning, which appears when the register dump for a
faulting process is printed in a kernel with SMP, DEBUG_PREEMPT, and
DEBUG_USER (with user_debug=31) enabled:
BUG: using smp_processor_id() in preemptible [00000000] code: init/1
caller is __show_regs+0x18/0x234
Backtrace:
[<c0159e5c>] (dump_backtrace+0x0/0x114) from [<c01faf30>] (dump_stack+0x18/0x1c)
r6:c781a000 r5:c0157544 r4:00000001 r3:00000000
[<c01faf18>] (dump_stack+0x0/0x1c) from [<c01e5230>] (debug_smp_processor_id+0xc4/0xf8)
[<c01e516c>] (debug_smp_processor_id+0x0/0xf8) from [<c0157544>] (__show_regs+0x18/0x234)
r6:c781bfb0 r5:00000000 r4:c781bfb0 r3:00000000
[<c015752c>] (__show_regs+0x0/0x234) from [<c01577a0>] (show_regs+0x40/0x50)
[<c0157760>] (show_regs+0x0/0x50) from [<c015c968>] (__do_user_fault+0x5c/0xa4)
r4:c781c000 r3:00000000
[<c015c90c>] (__do_user_fault+0x0/0xa4) from [<c015cbe0>] (do_page_fault+0x1b4/0x1e4)
r7:00000000 r6:00010000 r5:c781bfb0 r4:c781c000
[<c015ca2c>] (do_page_fault+0x0/0x1e4) from [<c01554c8>] (do_DataAbort+0x3c/0xa0)
[<c015548c>] (do_DataAbort+0x0/0xa0) from [<c01560c4>] (ret_from_exception+0x0/0x10)
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This updates the U300 defconfig to include the DMA driver merged
in 2.6.33-rc1 and adds a codepage that's needed to mount VFAT MMC
cards as default. The rest is new config options.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make registers unsigned for kernel space. This is important for
example in the perf events where the PC is stored into a u64. We
don't want it sign extended so make the regs unsigned to prevent
casts throughout the kernel.
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Somehow, strange characters made their way zaurus gpio .desc
fields. Fix it.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
There is a possibility of a loop happening in the PLL output clock
chain on the S3C64XX series. clk_mpll's parent was set to be
clk_mout_mpll, but this is fed from clk_fout_epll (which is also
clk_mpll).
clk_mpll is meant to be the output from the MPLL, and clk_mout_mpll
is a seperate clock derived from the mux of clk_mpll and clk_fin_mpll
and thus should be considered a seperate clock.
Anything using clk_mpll directly really should not be relying on this
being the clock that is eventually routed to a peripheral, so remove the
loop and ensure that the clocks accurately represent the clock chain
in the device.
The clk_mpll is not being used outside of the s3c6400-clock.c code, so
this change should not break anything else.
Do the same for the EPLL.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'davinci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci:
DaVinci: DM365: Add the device_enable for the DaVinci Keyscan
davinci: enable ARCH_HAS_HOLES_MEMORYMODEL for DaVinci
davinci: da8xx/omap-l1: mark RTC as a wakeup source
davinci: cp_intc: provide set_wake function
Davinci VPFE Capture: Take i2c adapter id through platform data
Adds the device_enable function to the DaVinci Keyscan platform data
to setup the PINMUX configuration.
It also removes #ifdef from the DM365 EVM board in order to load it
properly as a module.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
All DaVinci platforms include a DSP or co-processor for
audio/video acceleration.
While creating memory for the DSP/co-processor, system
integrator can end up creating a hole in the memory map
of the sort:
<kernel memory> <hole (memory for DSP)> <kernel memory>
This sort of configuration needs ARCH_HAS_HOLES_MEMORYMODEL
enabled. See further details see this discussion on ARM
linux mailing list:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15262.html
The patch is boot tested on OMAP-L138, DM6446 and DM355 EVMs
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Sriramakrishnan <srk@ti.com>
CC: Khasim Syed Mohammed <khasim@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On da850, RTC alarm is a wakeup source from deep sleep.
Mark it as a wakeup source after the rtc platform device
is registered.
Without this patch, the rtc-omap driver suspends the RTC
during the suspend sequence and hence it cannot wakeup the
SoC.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There is nothing special to be done for interrupts
which can wakeup the device from sleep on CP-INTC,
but not having a set_wake implemented prevents use
of common drivers which expect this function to be
implemented for all wakeup interrupt sources.
This patch fixes the issue encountered when using the
omap-rtc driver on DA850. On DA850 the RTC alarm
interrupt is used to wake up the SoC from deep sleep
mode. Without this patch, the disable_irq_wake throws
an unbalanced wake disable warning while resuming
because the previous enable call fails for lack of
set_wake implementation.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The I2C adapter ID is actually depends on Board and may vary, Davinci
uses id=1, but in case of AM3517 id=3.
So modified respective davinci board files.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
ARM: 5865/1: nuc900 ethernet driver needs mii
ARM: 5864/1: Implement arch_reset() in NUC900
ARM: 5863/1: fix bugs of clock source of NUC900
ARM: 5858/1: Remove unused vma_vm_flags macro from v7wbi_flush_user_tlb_range
imx/mx3: depend on USB_ULPI for otg_ulpi_create
ARM: MX3: make CPU revision number detection work on all boards
mx25: pdk: add platform code for FEC support
mx25: add support for FEC on i.MX25
mx25: s/NO_PAD_CTL/NO_PAD_CTRL/
mx31moboard: fix usbh device names
mx3: add support for the mt9v022 camera sensor to pcm037 platform
mx27: mxt_td60: Remove not used UART pins
[ARM] pxa/poodle: fix incorrect 'gpio_card_detect' of MMC
[ARM] pxa/zylonite: simplify reduntant gpio settings on mmc slot
[ARM] pxa/ttc_dkb: remove duplicate macro definition
[ARM] pxa/zeus: provide power-source information when APM is enabled
[ARM] pxa/zeus: relax memory timings on Zeus ethernet ports
[ARM] pxa/zeus: make internal zeus_get_pcb_info static
[ARM] pxa/littleton: select CPU_PXA300 and CPU_PXA310
[ARM] pxa/littleton: add UART3 GPIO config
...
Implement arch_reset(), reboot from shell become possible.
Signed-off-by: lijie <eltshanli@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fix following bugs:
1. typo error, CLOCK_EVT_MODE_PERIODIC -> CLOCK_EVT_FEAT_PERIODIC
2. TCSR register of timer1 missed PRESCALE
3. timer1 should be enabled before register it to clock source.
Signed-off-by: lijie <eltshanli@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
otg_ulpi_create is defined in drivers/usb/otg/ulpi.c which depends on
CONFIG_USB_ULPI. So protect its usage by the same symbol. Moreover
mxc_ulpi_access_ops needs CONFIG_MXC_ULPI.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 52939c03 (ARM: MX3: fix CPU revision number detection) started
using the CPU's SREV register for revision number detection. This
makes it mandatory to have a valid SPBA0 mapping. Add this to the
global map_io code instead of adding multiple copies for each board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Tested on Qong (EVB-Lite)
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Check whether L2 is present or not in XSC3. If it's present, enable L2
immediately.
Disabling L2 after L2 is enabled that would result in unpredicatable behavior
of XSC3 processor.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Outer cache checked whether L2 is enabled or not. If L2 isn't enabled in XSC3,
it would enable L2. This operation is evil that would make system hang.
In XSC3 core document, these words are mentioned in below.
"Following reset, the L2 Unified Cache Enable bit is cleared. To enable the L2
Cache, software may set the bit to a '1' before or at the same time as enabling
the MMU. Enabling the L2 Cache after the MMU has been enabled or disabling the
L2 Cache after the L2 Cache has been enabled, may result in unpredictable
behavior of the processor."
When outer cache is initialized, the MMU is already enabled. We couldn't enable
L2 after MMU enabled.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
PXA mmc host driver supports card detect, read only and power gpio pin
setting already. Zylonite platform driver needn't implement this any more.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
ARRAY_AND_SIZE is already defined arch/arm/mach-mmp/common.h which is
already included.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Bin Yang <bin.yang@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
DM9000s on Zeus sometime fail under heavy load.
Relaxing the timings a bit seems to be of a great help.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This has to be selected, otherwise some peripherals don't get initialized.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
