The 'pwrdm_for_each()' function walks powerdomains with a spinlock
locked, so the the callbacks cannot do anything which may sleep.
This patch introduces a 'pwrdm_for_each_nolock()' helper which does
the same, but without the spinlock locked. This fixes the following
lockdep warning:
[ 0.000000] WARNING: at kernel/lockdep.c:2460 lockdep_trace_alloc+0xac/0xec()
[ 0.000000] Modules linked in:
(unwind_backtrace+0x0/0xdc) from [<c0045464>] (warn_slowpath_common+0x48/0x60)
(warn_slowpath_common+0x48/0x60) from [<c0067dd4>] (lockdep_trace_alloc+0xac/0xec)
(lockdep_trace_alloc+0xac/0xec) from [<c009da14>] (kmem_cache_alloc+0x1c/0xd0)
(kmem_cache_alloc+0x1c/0xd0) from [<c00b21d8>] (d_alloc+0x1c/0x1a4)
(d_alloc+0x1c/0x1a4) from [<c00a887c>] (__lookup_hash+0xd8/0x118)
(__lookup_hash+0xd8/0x118) from [<c00a9f20>] (lookup_one_len+0x84/0x94)
(lookup_one_len+0x84/0x94) from [<c010d12c>] (debugfs_create_file+0x8c/0x20c)
(debugfs_create_file+0x8c/0x20c) from [<c010d320>] (debugfs_create_dir+0x1c/0x20)
(debugfs_create_dir+0x1c/0x20) from [<c000e8cc>] (pwrdms_setup+0x60/0x90)
(pwrdms_setup+0x60/0x90) from [<c002e010>] (pwrdm_for_each+0x30/0x80)
(pwrdm_for_each+0x30/0x80) from [<c000e79c>] (pm_dbg_init+0x7c/0x14c)
(pm_dbg_init+0x7c/0x14c) from [<c00232b4>] (do_one_initcall+0x5c/0x1b8)
(do_one_initcall+0x5c/0x1b8) from [<c00083f8>] (kernel_init+0x90/0x10c)
(kernel_init+0x90/0x10c) from [<c00242c4>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Earlier BeagleBoards were using pad AH8 muxed to GPIO29 for MMC write-protect.
However, this signal has been changed to pad AG9 in board revision C2.
Fix this by adding mux configuration for pad AG9, runtime check for board
revisions and set the gpio number and pad muxing accordingly.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO135 is used as EHCI (port2) phy reset pin on Multi Media Daughter card
connected to OMAP3EVM.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.infradead.org/mtd-2.6: (58 commits)
mtd: jedec_probe: add PSD4256G6V id
mtd: OneNand support for Nomadik 8815 SoC (on NHK8815 board)
mtd: nand: driver for Nomadik 8815 SoC (on NHK8815 board)
m25p80: Add Spansion S25FL129P serial flashes
jffs2: Use SLAB_HWCACHE_ALIGN for jffs2_raw_{dirent,inode} slabs
mtd: sh_flctl: register sh_flctl using platform_driver_probe()
mtd: nand: txx9ndfmc: transfer 512 byte at a time if possible
mtd: nand: fix tmio_nand ecc correction
mtd: nand: add __nand_correct_data helper function
mtd: cfi_cmdset_0002: add 0xFF intolerance for M29W128G
mtd: inftl: fix fold chain block number
mtd: jedec: fix compilation problem with I28F640C3B definition
mtd: nand: fix ECC Correction bug for SMC ordering for NDFC driver
mtd: ofpart: Check availability of reg property instead of name property
driver/Makefile: Initialize "mtd" and "spi" before "net"
mtd: omap: adding DMA mode support in nand prefetch/post-write
mtd: omap: add support for nand prefetch-read and post-write
mtd: add nand support for w90p910 (v2)
mtd: maps: add mtd-ram support to physmap_of
mtd: pxa3xx_nand: add single-bit error corrections reporting
...
- use __iomem type attribute where appropriate
- expand (a ? : b) to (a ? a : b)
As suggested by Russel King <linux@arm.linux.org.uk>
- remove a dead line from omapfb_main.c
Signed-off-by: Arun C <arunedarath@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed-by: Mike Wege <ext-mike.wege@nokia.com>
Fixed-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Fixed-by: Timo Savola <tsavola@movial.fi>
Fixed-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Fixed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add basic support for all 5 MMC controllers on OMAP4.
This patch doesn't include mmc-regulator support
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the ability for the driver to put the card power regulators to sleep
and wake them up again.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support for multi-level dynamic power saving states in omap_hsmmc
(ENABLED->DISABLED->OFF). In the "deepest" state (OFF) we switch off the
voltage regulators.
Signed-off-by: Denis Karpov <ext-denis.2.karpov@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let the board specify that a card is nonremovable e.g. eMMC
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PM dynamic OFF state results in context loss. That is, the host
controller has been powered off at some point, which means the registers
have been reset. The driver must detect when this happens, and restore
the context. This patch adds the means to detect context loss.
Note, the PM side is not yet implemented.
Signed-off-by: Denis Karpov <ext-denis.2.karpov@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds prefetch support to access nand flash in mpu mode.
This patch also adds 8-bit nand support (omap_read/write_buf8).
Prefetch can be used for both 8- and 16-bit devices.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Due to problems at cam.org, my nico@cam.org email address is no longer
valid. FRom now on, nico@fluxnic.net should be used instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
[ARM] Update mach-types
ARM: 5636/1: Move vendor enum to AMBA include
ARM: Fix pfn_valid() for sparse memory
[ARM] orion5x: Add LaCie NAS 2Big Network support
[ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
ARM: 5689/1: Update default config of HP Jornada 700-series machines
ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
ARM: 5688/1: ks8695_serial: disable_irq() lockup
ARM: 5687/1: fix an oops with highmem
ARM: 5684/1: Add nuc960 platform to w90x900
ARM: 5683/1: Add nuc950 platform to w90x900
ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
MMC: MMCI: convert realview MMC to use gpiolib
ARM: 5685/1: Make MMCI driver compile without gpiolib
ARM: implement highpte
ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
...
Fix up trivial conflict in arch/arm/kernel/signal.c.
It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83f ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.
* topic/asoc: (226 commits)
ASoC: au1x: PSC-AC97 bugfixes
ASoC: Fix WM835x Out4 capture enumeration
ASoC: Remove unuused hw_read_t
ASoC: fix pxa2xx-ac97.c breakage
ASoC: Fully specify DC servo bits to update in wm_hubs
ASoC: Debugged improper setting of PLL fields in WM8580 driver
ASoC: new board driver to connect bfin-5xx with ad1836 codec
ASoC: OMAP: Add functionality to set CLKR and FSR sources in McBSP DAI
ASoC: davinci: i2c device creation moved into board files
ASoC: Don't reconfigure WM8350 FLL if not needed
ASoC: Fix s3c-i2s-v2 build
ASoC: Make platform data optional for TLV320AIC3x
ASoC: Add S3C24xx dependencies for Simtec machines
ASoC: SDP3430: Fix TWL GPIO6 pin mux request
ASoC: S3C platform: Fix s3c2410_dma_started() called at improper time
ARM: OMAP: McBSP: Merge two functions into omap_mcbsp_start/_stop
ASoC: OMAP: Fix setup of XCCR and RCCR registers in McBSP DAI
OMAP: McBSP: Use textual values in DMA operating mode sysfs files
ARM: OMAP: DMA: Add support for DMA channel self linking on OMAP1510
ASoC: Select core DMA when building for S3C64xx
...
The omap_device code provides a mapping of omap_hwmod structures into
the platform_device system, and includes some details on external
(board-level) integration. This allows drivers to enable, idle, and
shutdown on-chip device resources, including clocks, regulators, etc.
The resources enabled and idled are dependent on the device's maximum
wakeup latency constraint (if present).
At the moment, omap_device functions are intended to be called from
platform_data function pointers. Ideally in the future these
functions will be called from either subarchitecture-specific
platform_data activate, deactivate functions, or via an custom
bus/device type for OMAP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Eric Thomas <ethomas@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
OMAP SoCs can be considered a collection of hardware IP blocks
connected by various interconnects. The bus topology and device
integration data is somewhat more complex than platform_device can
encode. This patch creates code and structures to manage information
about OMAP on-chip devices ("hardware modules") and their integration
to the rest of the chip. Hardware module data is intended to be
generated dynamically from the TI hardware database for the OMAP4
chips and beyond, easing Linux support for new chip variants.
This code currently:
- resets and configures all hardware modules upon startup, reducing bootloader
dependencies;
- provides hooks for Linux driver model code to enable, idle, and shutdown
hardware modules (forthcoming patch);
- waits for hardware modules to leave idle once their clocks
are enabled and OCP_SYSCONFIG bits are set appropriately.
- provides a means to pass arbitrary IP block configuration data (e.g.,
FIFO size) to the device driver (via the dev_attr void pointer)
In the future this code is intended to:
- estimate interconnect bandwidth and latency characteristics to
ensure constraints are satisfied during DVFS
- provide *GRPSEL bit data to the powerdomain code
- handle pin/ball muxing for devices
- generate IO mapping information dynamically
- supply device firewall configuration data
- provide hardware module data to other on-chip coprocessor software
- allow the removal of the "disable unused clocks" code in the OMAP2/3
clock code
This patch represents a collaborative effort involving many people from TI,
Nokia, and the Linux-OMAP community.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Eric Thomas <ethomas@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Most board-*.c files read configuration data from the bootloader in
their .init_machine() function. This needs to happen earlier, at some
point before omap2_init_common_hw() is called. This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The interface provides device drivers, CPUFreq, and DSPBridge with a
means of controlling OMAP power management parameters that are not yet
supported by the Linux PM PMQoS interface. Copious documentation is
in the patch in Documentation/arm/OMAP/omap_pm and the interface
header file, arch/arm/plat-omap/include/mach/omap-pm.h.
Thanks to Rajendra Nayak <rnayak@ti.com> for adding CORE (VDD2) OPP
support and moving the OPP table initialization earlier in the event
that the clock code needs them. Thanks to Tero Kristo
<tero.kristo@nokia.com> for fixing the parameter check in
omap_pm_set_min_bus_tput(). Jouni signed off on Tero's patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Jouni Högander <jouni.hogander@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Igor Stoppa <igor.stoppa@nokia.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Veeramanikandan Raju <veera@ti.com>
Cc: Karthik Dasu <karthik-dp@ti.com>
This patch provides the debugfs entries and a function which will be
called by the PM code to register the time spent per domain per
state. Also some new fields are added to the powerdomain struct to
keep the time information.
NOTE: As of v2.6.29, using getnstimeofday() after drivers are
suspended is no longer safe since the timekeeping subsystem is also
suspended as part of the suspend process. Instead use sched_clock()
which on OMAP returns the 32k SYNC timer in nanoseconds.
Also, do not print out status for meta powerdomains (dpll*)
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add some infrastructure to easily iterate over clock and power
domains.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch provides the infrastructure to count how many times a
powerdomain entered a given power state (on, inactive, retention,
off). A number of functions are provided which will be called by the
chip specific powerdomain and clockdomain code whenever a transition
might have happened.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch changes for setting the padconf value for sys_nirq line
which is connected to T2 INTR1. This will fix the T2 keypad wakeup
issue on OMAP3 SDP.
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For OMAP3 add MMC1 MMC2 pin mux MMC3 mux is not added as there are
multiple configurations possible, so the muxing is left to be done
in board file.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Chikkature Rajashekar <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables to peek the following data.
$ /debug/iommu/isp# ls
mem nr_tlb_entries regs
mmap pagetable tlb
$ /debug/iommu/isp# head pagetable
L: da: pa:
-----------------------------------------
2: 00001000 8ae4a002
2: 00002000 8e7bb002
2: 00003000 8ae49002
2: 00004000 8ae65002
.....
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP tags are deprecrated so drop them.
Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.
Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.) After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Omap tags are deprecated and remove OMAP_TAG_SERIAL_CONSOLE. Console must be
enabled with the console boot parameter instead.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.
Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.
In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Functionality of functions omap_mcbsp_xmit_enable and omap_mcbsp_recv_enable
can be merged into omap_mcbsp_start and omap_mcbsp_stop since API of
those omap_mcbsp_start and omap_mcbsp_stop was changed recently allowing
to start and stop individually the transmitter and receiver.
This cleans up the code in arch/arm/plat-omap/mcbsp.c and in
sound/soc/omap/omap-mcbsp.c which was the only user for those removed
functions.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
FCLK may get autogated so that it prevents the McBSP
to work properly. It is the bit 9 that must be set
for maintaining the McBSP FCLK.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Configure only XRDYEN and RRDYEN wakeup signals
in order to get better power consumption.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch enables the smart idle mode while
McBPS is being utilized. Once it's done,
force idle mode is taken instead. Apart of it,
it also configures what signals will wake mcbsp up.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It adds a new sysfs file, where the user can configure the mcbsp mode to use.
If the mcbsp channel is in use, it does not allow the change.
Than in omap_pcm_open we can call the omap_mcbsp_get_opmode to get the mode,
store it, than use it to implement the different modes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch export through sysfs two properties to configure
maximum threshold for transmission and reception on each
mcbsp instance. Also, it exports two helper functions to
allow mcbsp users to read this values.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a way to handle transmit/receive threshold.
It export to mcbsp users a callback registration procedure.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adding McBSP register definition for IRQEN, IRQSTATUS, THRESHOLD2 and THRESHOLD1 registers.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC has an annoying bug letting either L or R channel to be
played on L channel. In other words, L and R channels can
switch at random. This provides McBSP funtionality that may
be used to fix this feature.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There's no need to keep these defines limited in the ifdef block
for mach-omap2. It will just cause problems testing for the CPU
revision in the common code, like the next patch does for the DMA
errata.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Simultaneous audio playback and capture on OMAP1510 can cause that second
stream is stalled if there is enough delay between startup of the audio
streams.
Current implementation of the omap_mcbsp_start is starting both transmitter
and receiver at the same time and it is called only for firstly started
audio stream from the OMAP McBSP based ASoC DAI driver.
Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is
missed if there is no DMA transfer set up at that time when the first word
after McBSP startup is transmitted. The problem hasn't noted before since
later OMAPs are using level sensitive DMA request lines.
Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by
allowing to start and stop individually McBSP transmitter and receiver
logics. Then call those functions individually for both audio playback
and capture streams. This ensures that DMA transfer is setup before
transmitter or receiver is started.
Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem
analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA
request line behavior differences between the OMAP generations.
Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
