LAN9115 Ethernet only works on SMDK6410 if certain switches
are set in specific ways. Document the requirement.
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since the mach-smdk6410.c file claims it can start up the
smsc9115 ethernet device on the board, it should take care
about configuring the necessary chip select nCS1 so it can
see the chip. The select defaults to 8-bit mode so without
config the Ethernet doesn't work.
This patch uses the new SROM definitions to set nCS1 to the
state found in the Samsung U-Boot port for 6410. It may be
more conservative that it needs to be since those settings
were marked as for CS8900A also using this chip select.
But this change is enough to get the ethernet working when
booted with Qi.
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Prepare for the forthcoming device changes by renaming s3c_device_usb to
s3c_device_ohci as this is what the device represents.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since the fixed voltage regulator grew support for GPIO based
enables and GPIO 0 is valid on some systems we need to specify
that there is no valid GPIO enable control.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This adds support for the third SDHCI controller.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
DVDD is supplied by supplies derived from the PMIC, AVDD and PVDD are
supplied from the main wall supply on the base board which runs at
5V. No option is currently supported for running without a PMIC card,
the assumption is that the regulator API will be built out when no
soft PMIC card is in use.
To ease merge issues since this uses the newly added dev_name supply
configuration from the regulator API (currently in -next only) the
fixed voltage regulator is ifdefed out when the regulator API is not
enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The WM835x has some GPIOs on it, allocate some space so we can use
them with gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When used with the WM1190-EV1 board we can use the internal pull up
resistor of the CPU to provide the required pull for the IRQ line.
Without this interrupts from the WM835x don't work in the default
WM1190-EV1 hardwaer configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A number of machines that need s3c_device_nand present do not select
this in their Kconfig entries. Add the necessary selection of the
configuration S3C_DEV_NAND so that we avoid the following error:
arch/arm/mach-s3c2410/built-in.o: In function `bast_map_io':
arch/arm/mach-s3c2410/mach-bast.c:634: undefined reference to `s3c_device_nand'
arch/arm/mach-s3c2412/built-in.o: In function `s3c2412_init_uarts':
arch/arm/mach-s3c2412/s3c2412.c:109: undefined reference to `s3c_device_nand'
arch/arm/mach-s3c2412/built-in.o: In function `jive_machine_init':
arch/arm/mach-s3c2412/mach-jive.c:673: undefined reference to `s3c_device_nand'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add proper uartcfg for UART port 2,3 and tidy it up on SMDK6410.
Signed-off-by: Matt Hsu <matt@0xlab.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make ncp_iodesc struct static to clean a public namespace a bit and move
it to __initdata section to save memory a bit.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the s3c_device_nand platform device from plat-s3c24xx to plat-s3c,
now that the nand driver also support the s3c64xx devices.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for the Airgoo HMT (home media terminal) device.
The HMT is a tablet device with a s3c6410, a 7" LCD and a number
of peripheral connections.
For more details of the hardware specs, see:
http://article.gmane.org/gmane.linux.debian.devel.embedded/4307
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
[ben-linux@fluff.org: subject rewrite]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for S3C6400 SDHCI channels 0 and 1, making
the GPIO code common to both S3C6400 and S3C6410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add USB OHCI host capability to the SMDK6410 for either USB OtG or
a single/double USB host port.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This allows the S3C CPUfreq driver to do DVFS.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A&W6410 board uses Samsung S3C6410 SoC and it is registered with 2183.
Framebuffer and ethernet devices are supported currently.
Unnecessary header file is removed.
Fix to use __raw_writel() and __raw_readl() for accessing mapped address.
Thank you for your comments.
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since no consumers are currently configured for the SMDK6410 mark all
the supplies on the board as being always_on, ensuring interoperability
with future regulator API changes to disable unused regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Using an active high IRQ ensures that the WM8350 interrupt handling
does not spin when used with a SMDK6410 which has not had R20 removed
and R21 fitted to connect EINT12 to the PMIC module rather thant the
fixed regulators on the CPU module.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is a basic support for NCP board based on s3c6410.
Only enables the serial. also remove empty i2c device.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The SMDK6410 supports pluggable PMIC boards. One such board is the
Wolfson Microelectronics 1190-EV1 for the WM8350 PMICs. This patch
introduces initial support for this module. Further patches will
add additional integration with the system as support for the
S3C6410 and other devices on the system improves.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ensure that the LCD output type is RGB and that
the modem interface is not bypassing the LCD
block. This ensures the LCD interface output
gets to the pins in the correct format.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Going forward gpio_request() will be a requirement for GPIO API users so
call it for the LCD power GPIOs. With present code the kernel functions
but generaets loud WARN_ON()s when using the unrequested GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The WM8580 driver registers itself as "wm8580" rather than "WM8580".
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The function s3c64xx_init_io was missing from <plat/cpu.h>
and was masked by the SMDK6410 having an local definition.
Fix by removing the SMDK6410 variant and adding it to the
relevant <plat/cpu.h> file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the definition for the hsmmc device to plat-s3c
to be shared between the s3c24xx and s3c64xx platforms.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some of the startup output can be reduced to
KERN_DEBUG from KERN_INFO as it is only really
useful when trying to debug kernel initialisation
problems.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
