This patch is an improvement to 4bba0fd8d1
which got to mainline a little early.
Sudhakar Rajashekhara explains that at least OMAP-L138 requires MDR mode
settings before DXR for correct behaviour, so load MDR first with
STT cleared and later load again with STT set.
Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When setting up to transmit, a race exists between the ISR and
i2c_davinci_xfer_msg() trying to load the first byte and adjust counters.
This is mostly visible for transmits > 1 byte long.
The hardware starts sending immediately that MDR is loaded. IMR trickery
doesn't work because if we start sending, finish the first byte and an
XRDY event occurs before we load IMR to unmask it, we never get an
interrupt, and we timeout.
Move the MDR load after DXR,IMR loads to avoid this race without locking.
Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Come out of i2c time out condition by following the
bus recovery procedure outlined in the i2c protocol v3 spec.
The kernel must be robust enough to gracefully recover
from i2c bus failure without having to reset the machine.
This is done by first NACKing the slave, pulsing the SCL
line 9 times and then sending the stop command.
This patch has been tested on a DM6446 and DM355
Signed-off-by: Philby John <pjohn@in.mvista.com>
Signed-off-by: Srinivasan, Nageswari <nageswari@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Add cpufreq support for DaVinci I2C driver.
Tested on DA850/OMAP-L138 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Add suspend and resume callbacks to DaVinci I2C driver.
This has been tested on DA850/OMAP-L138 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Add i2c reset control and clock divider calculation functions
which will be useful for power management features.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cleanup the DaVinci I2C driver. Remove MOD_REG_BIT macro.
Also use ioremap instead of IO_ADDRESS macro.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
This fixes Oops at kernel startup while "scanning" for TLV320AIC23IDx
addresses.
Additional fix from Sudhakar Rajashekhara: I think 'first byte set'
should come after the write because an I2C transaction is being
carried out before configuring the I2C mode register (which has bits
to configure Master, Start condition etc), which causes undefined
behavior.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Alexander Vasiliev <alexvasiljev@gmail.com>
Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make i2c-davinci cope properly with "i2cdetect": don't spew
syslog spam on perfectly normal behaviors, or respond to any
address other than the one reserved for the SMBus host.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
DaVinci core code has converted to the new clkdev API so
clock name strings are not needed. Instead, just the a
'struct device' pointer is needed.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Properly set the adapter timeout value in jiffies, and then use that
value in the driver, rather than a hard-coded constant.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Kevin Hilman <khilman@mvista.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If an interrupt happens before an I2c master read/write,
complete is called on uninitialized structure.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If wait_for_completion_interruptible_timeout exits due
to a signal, the i2c bus was locking up.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Interrupts are enabled at the point where the DAVINCI_I2C_IVR_REG is read,
so unless an interrupt happened just at that moment, no interrupt would be
pending. Even though documentation implies you should do this, I see no
reason. If slave support is added, this read would cause a hard to
reproduce bug.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Previously the dev_dbg only printed if no error.
Printing also on an error is more useful
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Ensure psc value gives a clock between 7-12 MHz
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Since 43cc71eed1, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to the
hotpluggable I2C platform drivers, to allow module auto loading.
[ db: add some more drivers ]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
__FUNCTION__ is gcc-specific, use __func__.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
DAVINCI_I2C_STR_REG is a write 1 to clear register,
so don't use a read/modify/write cycle.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I2C adapter drivers are supposed to handle retries on nack by themselves
if they do, so there's no point in setting .retries if they don't.
As this retry mechanism is going away (at least in its current form),
clean this up now so that we don't get build failures later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Acked-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
