Some minor refactoring in the generic code was necessary for
this:
1) This controller requires 8-byte access to the interrupt map
and clear register. They are 64-bits on all the other
SBUS and PCI controllers anyways, so this was easy to cure.
2) The IMAP register has a different layout and some bits that we
need to preserve, so use a read/modify/write when making
changes to the IMAP register in generic code.
3) Flushing the entire IOMMU TLB is best done with a single write
to a register on this PCI controller, add a iommu->iommu_flushinv
for this.
Still lacks MSI support, that will come later.
Signed-off-by: David S. Miller <davem@davemloft.net>
This starts bringing the PowerPC and Sparc64 implemetations back closer
together.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to simplify sharing code with powerpc which
has properties that have various forms of capitalization
when on the sparc64 side the property is all lower-case.
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, we actually change the functions themselves.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in schizo_irq_trans_init() should set irq_data->sync_reg
to the location of the SYNC register if this is Tomatillo, and set
it to zero otherwise. But that is not what it is doing.
As a result, non-Tomatillo systems were trying to access a
non-existent register resulting in bus errors at the first
PCI interrupt.
Thanks to Roland Stigge for the bug report.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) probe_other_fhcs() wants to see only non-central FHC
busses, so skip FHCs that don't sit off the root
2) Like SBUS, FHC can lack the appropriate address and
size cell count properties, so add an of_busses[]
entry and handlers for that.
3) Central FHC irq translator probing was buggy. We
were trying to use dp->child in irq_trans_init but
that linkage is not setup at this point.
So instead, pass in the parent of "dp" and look for
the child "fhc" with parent "central".
Thanks to the tireless assistence of Ben Collins in tracking
down these problems and testing out these fixes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabre and Psycho PCI controllers can have partial interrupt-map
properties, meaning that on-board devices don't match up to any
entries. Instead, they are fully specified from the beginning and
we should pass them directly to the IRQ translator as-is.
Also, fill in the necessary translator slots for the "graphics"
and "expansion UPA" interrupts on Sabre, Psycho, and SYSIO SBUS.
Increase PROMREG_MAX to 24, as seen on SUNW,ffb devices.
Finally, prevent accidentally writing past the end of the of_device
struct resource[] and irqs[] arrays. Spit out a log message when
we ignore some entries because there are too many of them.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is only needed when there is a PCI-PCI bridge sitting
between the device and the PCI host controller which is
not a Simba APB bridge.
Add logic to handle two special cases:
1) device behind EBUS, which sits on PCI
2) PCI controller interrupts
Signed-off-by: David S. Miller <davem@davemloft.net>
When installing the IRQ pre-handler, we were not setting up the second
argument correctly. It should be a pointer to the sabre_irq_data, not
the config space PIO address.
Furthermore, we only need this pre-handler installed if the device
sits behind a PCI bridge that is not Sabre or Simba/APB.
Signed-off-by: David S. Miller <davem@davemloft.net>
Do IRQ determination generically by parsing the PROM properties,
and using IRQ controller drivers for final resolution.
One immediate positive effect is that all of the IRQ frobbing
in the EBUS, ISA, and PCI controller layers has been eliminated.
We just look up the of_device and use the properly computed
value.
The PCI controller irq_build() routines are gone and no longer
used. Unfortunately sbus_build_irq() has to remain as there is
a direct reference to this in the sunzilog driver. That can be
killed off once the sparc32 side of this is written and the
sunzilog driver is transformed into an "of" bus driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Import some more stuff from powerpc.
Add of_device_is_compatible(), and of_find_compatible_node().
Export some more of the other routines to modules.
Signed-off-by: David S. Miller <davem@davemloft.net>
One thing this change pointed out was that we really should
pull the "get 'local-mac-address' property" logic into a helper
function all the network drivers can call.
Signed-off-by: David S. Miller <davem@davemloft.net>
The basic framework is based on the PowerPC OF code.
This code even tries to get the device addressing components
correct in the full path names.
Signed-off-by: David S. Miller <davem@davemloft.net>
