When controlling an industrial radio modem it can be necessary to
manipulate the handshake lines in order to control the radio modem's
transmitter, from userspace.
The transmitter should not be turned off before all characters have been
transmitted. serial8250_tx_empty() was reporting that all characters were
transmitted before they actually were.
===
Discovered in parallel with more testing and analysis by Kees Schoenmakers
as follows:
I ran into an NetMos 9835 serial pci board which behaves a little
different than the standard. This type of expansion board is very common.
"Standard" 8250 compatible devices clear the 'UART_LST_TEMT" bit together
with the "UART_LSR_THRE" bit when writing data to the device.
The NetMos device does it slightly different
I believe that the TEMT bit is coupled to the shift register. The problem
is that after writing data to the device and very quickly after that one
does call serial8250_tx_empty, it returns the wrong information.
My patch makes the test more robust (and solves the problem) and it does
not affect the already correct devices.
Alan:
We may yet need to quirk this but now we know which chips we have a
way to do that should we find this breaks some other 8250 clone with
dodgy THRE.
Signed-off-by: Dick Hollenbeck <dick@softplc.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Kees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cc: Sasha Hauer <kernel@pengutronix.de>
We noticed that we were only able to communicate once with a GSM module
per session, if we powered down the module then the serial driver was
broken until reset, no traffic or /proc/interrupts activity could be
seen any more.
Volker noticed it was provoked by a long "break" seen on the wire when
the RX was not driven during powerdown, we discovered we could kill the
serial driver just by forcing RX low extenally for a little while.
I saw that the processing for BREAK in the driver gets too excited and
clears down all set bits in USR2, including that a character is pending.
This stops all further characters getting processed.
The attached one-liner makes the serial driver immortal against BREAK.
Signed-off-by: Andy Green <andy.green@txtr.com>
Signed-off-by: Volker Ernst <volker.ernst@txtr.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
machine is compatible is an OF-specific call. It should have
the of_ prefix to protect the global namespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
Add support for ARM-based SH-Mobile CPUs to the sh-sci driver.
Also remove the SCLSR register that is missing on sh772x, sh7705 and
SH-Mobile.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since sci_rxd_in() is used by SCI only, clean up
the header file by killing off code dealing with
SCIF ports and their register definitions.
Also introduce a default sci_rxd_in() function
which can be shared by all SCIF-only processors.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As part of the development process, it is hoped PLAT_S3C is either removed
from all of the PLAT_SAMSUNG derived platforms or removed entirely. It is
also better to use PLAT_SAMSUNG as this is the current base of all Samsung
devices.
Change the two places that use PLAT_S3C to use PLAT_SAMSUNG
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C2412 has a fractional baud rate register, this patch adds the
corresponding flag to the UART definition to allow generation of more
precise baud rates for the various clock combinations.
Signed-off-by: Michel Pollet <buserror@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds UART serial port support for S5PV210.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
fmvj18x_cs, serial_cs:
add new id
Panasonic lan & modem card (model name:AL-VML101)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quirk is applied on all cards with given manfid (is it that correct?).
Unfortunately, that quirk breaks resume on zaurus with billionton
bluetooth card inserted: c950ctrl is 0 and outb() faults.
I believe it is simply not a multiport card. (info->multi == 1). ...
... confirmed by printks.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since UCR1_UARTEN is defined 1, the port was always treated as enabled.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Oskar Schirmer <os@emlix.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabian Godehardt <fg@emlix.com>
Cc: Daniel Glöckner <dg@emlix.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In that situation if the old rate is invalid and the new rate is invalid
and the chip cannot do 9600 baud we report zero, which makes all the
drivers explode.
Instead force the rate based on min/max
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Perform a tricky suspend/resume even with no_console_suspend.
With no_console_suspend, kernel skips serial port suspend/resume and the
serial hardware may remain in undefined state after resume. It actually
happens on devices that don't have BIOS that handle serial
initialization. It makes impossible to use serial console after resume.
Devices affected by this problem include:
Sharp Zaurus devices
Several PXA based ARM embedded boards
The patch does:
- Save the hardware state
- Perform buffer flush in time of its suspend call
- Tell the driver that port is suspended
- But still accept new data
- And keep console hardware in state that allows to send them
It allows to capture late console messages without breaking console
after resume.
This is just a resend of a patch discussed in these threads, as the
patch was not yet applied.
"Possible suspend/resume regression in .32-rc?" (Nov 1-5, 2009, ARM
list, later LKML)
"serial-core: resume serial hardware with no_console_suspend" (Sep
15-Oct 18, 2009, LKML & ARM lists)
Signed-off-by: Stanislav Brabec <sbrabec@suse.cz>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wacom claims that the WACF namespace will always be devoted to serial
Wacom tablets. Remove the existing entries and add a wildcard to avoid
having to update the kernel every time they add a new device.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch modifies s3c24xx_serial_initconsole function to accept multiple
platform UART information structures. This is required on platforms that have
differences among the instances of UART ports. As an example, the FIFO sizes
could be different for each UART instance and hence multiple platform UART
information structures would be needed.
This patch also modifies the s3c24xx_console_init macro since it wraps the
call to the s3c24xx_serial_initconsole function.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Move cpu hotplug driver lock from pseries to powerpc
powerpc: Move /proc/ppc64 to /proc/powerpc update
powerpc/8xx: Fix user space TLB walk in dcbX fixup
powerpc: Fix decrementer setup on 1GHz boards
powerpc/iseries: Initialise on-stack completion
powerpc/hvc: Driver build breaks with !HVC_CONSOLE
serial/pmac_zilog: Workaround problem due to interrupt on closed port
powerpc/macintosh: Make Open Firmware device id constant
powerpc: Use helpers for rlimits
powerpc: cpumask_of_node() should handle -1 as a node
powerpc/pseries: Fix dlpar compile warning without CONFIG_PROC_DEVICETREE
powerpc/pseries: Fix xics interrupt affinity
powerpc/swsusp_32: Fix TLB invalidation
powerpc/8xx: Always pin kernel instruction TLB
powerpc: 2.6.33 update of defconfigs for embedded 6xx/7xxx, 8xx, 8xxx
powerpc: Use scripts/mkuboot.sh instead of 'mkimage'
powerpc/5200: update defconfigs
This is a new two finger touch Fujitsu Wacom Tablet PC.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds UART serial port support for S5P6440 CPU. Most of the
serial support of Samsung's 6400 CPU is reused for 6440 CPU.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
It seems that in qemu, we can see an interrupt in R3 despite the
fact that it's masked in W1. The chip doesn't actually issue an
interrupt, but we can "see" it when taking an interrupt for the
other channel. This may be a qemu bug ... or not, so let's be
safe and avoid calling into the UART layer when that happens which
woulc cause a crash.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Rob Landley <rob@landley.net>
The sh-sci driver used the wrong fifosize for PORT_SCIFA and PORT_SCIF
ports. If an incorrect size is used, the serial core will enforce an
early shutdown on the port, especially with baudrates < 9600.
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options
ARM: Fix wrong dmb
ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock
ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards
ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h
ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes
ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set
ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code"
ARM: 5867/1: Update U300 defconfig
ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs
[ARM] pxa: fix strange characters in zaurus gpio .desc
ARM: add missing recvmmsg syscall number
[ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*()
[ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *'
[ARM] pxa: enable L2 if present in XSC3
[ARM] pxa: do not enable L2 after MMU is enabled
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
sky2: Fix oops in sky2_xmit_frame() after TX timeout
Documentation/3c509: document ethtool support
af_packet: Don't use skb after dev_queue_xmit()
vxge: use pci_dma_mapping_error to test return value
netfilter: ebtables: enforce CAP_NET_ADMIN
e1000e: fix and commonize code for setting the receive address registers
e1000e: e1000e_enable_tx_pkt_filtering() returns wrong value
e1000e: perform 10/100 adaptive IFS only on parts that support it
e1000e: don't accumulate PHY statistics on PHY read failure
e1000e: call pci_save_state() after pci_restore_state()
netxen: update version to 4.0.72
netxen: fix set mac addr
netxen: fix smatch warning
netxen: fix tx ring memory leak
tcp: update the netstamp_needed counter when cloning sockets
TI DaVinci EMAC: Handle emac module clock correctly.
dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chips
ixgbe: Fix compiler warning about variable being used uninitialized
netfilter: nf_ct_ftp: fix out of bounds read in update_nl_seq()
mv643xx_eth: don't include cache padding in rx desc buffer size
...
Fix trivial conflict in drivers/scsi/cxgb3i/cxgb3i_offload.c
The console hangs during bootup when disable_irq is called from the
transmit interrupt handler (it will wait forever for it's "own"
interrupt in synchronize_irq). Fix by using disable_irq_nosync()
instead.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pcnet_cs,serial_cs:
add cis of KTI PE520 pcmcia network card,
and serial card(Sierra Wireless AC860).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
ctrl_xxx() is an antiquated SH interface, while __raw_xxx is the standard
API that accomplishes the same thing. As such, this converts the
remaining sh-sci straggles over, which enables the driver to be wired up
for ARM SH-Mobile CPUs as well.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This establishes a sensible max baud rate for the earlyprintk cases where
the port's uartclk has not yet been determined.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (33 commits)
sh: Fix test of unsigned in se7722_irq_demux()
sh: mach-ecovec24: Add FSI sound support
sh: mach-ecovec24: Add mt9t112 camera support
sh: mach-ecovec24: Add tw9910 support
sh: MSIOF/mmc_spi platform data for the Ecovec24 board
sh: ms7724se: Add ak4642 support
sh: Fix up FPU build for SH5
sh: Remove old early serial console code V2
sh: sh5 scif pdata (sh5-101/sh5-103)
sh: sh4a scif pdata (sh7757/sh7763/sh7770/sh7780/sh7785/sh7786/x3)
sh: sh4a scif pdata (sh7343/sh7366/sh7722/sh7723/sh7724)
sh: sh4 scif pdata (sh7750/sh7760/sh4-202)
sh: sh3 scif pdata (sh7705/sh770x/sh7710/sh7720)
sh: sh2a scif pdata (sh7201/sh7203/sh7206/mxg)
sh: sh2 scif pdata (sh7616)
sh-sci: Extend sh-sci driver with early console V2
sh: Stub in P3 ioremap support for nommu parts.
sh: wire up vmallocinfo support in ioremap() implementations.
sh: Make the unaligned trap handler always obey notification levels.
sh: Couple kernel and user write page perm bits for CONFIG_X2TLB
...
Two IOC3 and IOC4 drivers have broken error paths on registration. Fix
them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several IOC3 and IOC4 drivers misuse the __devinit and __devexit section
markers. Use __init and __exit instead as appropriate, then add __devinit
and __devexit where they really belong for PCI drivers.
Also make ioc4_serial_init static.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is V2 of early serial console support for the sh-sci
driver. The early serial console is using early platform
devices and "earlyprintk". To use this feature the early
platform devices must be broken out to one device per port
and the desired port should be selected on the kernel command
line like: "earlyprintk=sh-sci.N[,baudrate][,keep]"
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (58 commits)
tty: split the lock up a bit further
tty: Move the leader test in disassociate
tty: Push the bkl down a bit in the hangup code
tty: Push the lock down further into the ldisc code
tty: push the BKL down into the handlers a bit
tty: moxa: split open lock
tty: moxa: Kill the use of lock_kernel
tty: moxa: Fix modem op locking
tty: moxa: Kill off the throttle method
tty: moxa: Locking clean up
tty: moxa: rework the locking a bit
tty: moxa: Use more tty_port ops
tty: isicom: fix deadlock on shutdown
tty: mxser: Use the new locking rules to fix setserial properly
tty: mxser: use the tty_port_open method
tty: isicom: sort out the board init logic
tty: isicom: switch to the new tty_port_open helper
tty: tty_port: Add a kref object to the tty port
tty: istallion: tty port open/close methods
tty: stallion: Convert to the tty_port_open/close methods
...
Do not read IIR in serial8250_start_tx when UART_BUG_TXEN
Reading the IIR clears some oustanding interrupts so it is not safe.
Instead, simply transmit immediately if the buffer is empty without
regard to IIR.
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Intel(R) PXA27x Processor Family Specification Update (Nov 2005)
says:
E75. UART: Baud rate may not be programmed correctly on
back-to-back writes.
Problem:
When programming the Divisor Latch registers, Low and High (DLL and
DLH), with back-to-back writes, the second register write may not
take effect. The result is an incorrect baud rate.
Workaround:
After programming the first Divisor Latch register, read and verify
it before programming the second Divisor Latch register.
This was hit when changing the baud rate from 115200 to 9600 while
receiving characters at 9600 Bd.
And fixed indention of some comments nearby.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding EEH handlers for the serial jsm driver. This patch adds
the PCI error handlers and also register them to be called when
a error is detected.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently there is a field in the jsm_board structure to cont
the number of interrupt that the card recevived, but it's not
working properly when the IRQ line is shared, and also nowhere
else this field is used. So, This patch is removing it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the jsm_channel->ch_wopen field is defined and never
used. So, this patch removes it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the field jsm_channel->ch_cpstime is defined but never
used, so this patch removes it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the field jsm_channel->ch_old_baud is not used, just
assigned in a lot of places but never used. This patches removes
this field.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the ch_custom_speed field exists but is never used,
so, this patch removes it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Actually jsm displays "Device Added" 8 times (for a 8 port device).
This silly patch just makes things more informative, showing
the port (instead of the device) that was added.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently jsm is showing the following message when loaded:
IRQ 432/JSM: IRQF_DISABLED is not guaranteed on shared IRQs
It's because the request_irq() is called using IRQF_DISABLED
and IRQF_SHARED.
Actually there is no need to use IRQF_DISABLED in this driver.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unfortunately, one cannot hold on to the struct firmware
that request_firmware_nowait() hands off, which is needed
in some cases. Allow this by requiring the callback to
free it (via release_firmware).
Additionally, give it a gfp_t parameter -- all the current
users call it from a GFP_KERNEL context so the GFP_ATOMIC
isn't necessary. This also marks an API break which is
useful in a sense, although that is obviously not the
primary purpose of this change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: Abhay Salunke <abhay_salunke@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: export clk_* symbols in clk.c
m68knommu: Split the .init section into INIT_TEXT_SECTION and INIT_DATA_SECTION.
m68knommu: Move __init_end out of the .init section.
m68knommu: Move __init_begin out of the .init section.
m68knommu: Use more macros inside the .init section.
m68knommu: Use INIT_TASK_DATA and CACHELINE_ALIGNED_DATA.
m68knommu: Make THREAD_SIZE available to assembly files.
m68knommu: Don't hardcode the value of PAGE_SIZE in the linker script.
m68knommu: rename BSS define in linker script
m68knommu: add a task_pt_regs() macro
m68knommu: define arch_has_single_step() and friends
m68knommu: add uboot commandline argument passing support
m68knommu: Coldfire GPIO corrections
m68knommu: move mcf_remove to .devexit.text
Fixed up (?) conflict in arch/m68k/include/asm/ptrace.h
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
sh: include empty zero page in romImage
sh: Make associative cache writes fatal on all SH-4A parts.
sh: Drop associative writes for SH-4 cache flushes.
sh: Partial revert of copy/clear_user_highpage() optimizations.
sh: Add default uImage rule for se7724, ap325rxa, and migor.
sh: allow runtime pm without suspend/resume callbacks
sh: mach-ecovec24: Remove un-defined settings for VPU
sh: mach-ecovec24: LCDC drive ability become high
sh: fix sh7724 VEU3F resource size
serial: sh-sci: Fix too early port disabling.
sh: pfc: pr_info() -> pr_debug() cleanups.
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
sh: Improve kfr2r09 serial port setup code
sh: Break out SuperH PFC code
sh: Move KEYSC header file
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
sh: Add CPG save/restore code for sh7724 R-standby
sh: Add SDHI power control support to Ecovec
mfd: Add power control platform data to SDHI driver
sh: mach-ecovec24: modify address map
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6:
sparc: Set UTS_MACHINE correctly.
sparc,leon: init_leon srmmu cleanup
sparc32: Remove early interrupt enable.
sparc, leon: Added Aeroflex Gaisler entry in manufacturer_info structure
sparc64: Faster early-boot framebuffer console.
Revert "sparc: Make atomic locks raw"
sparc: remove unused nfsd #includes
sparc: Fixup last users of irq_chip->typename
Added sparc_leon3_snooping_enabled() and converted extern inline to static inline
No auxio on LEON
apbuart: Use of_find_node_by_path to find root node.
sparc: Replace old style lock initializer
sparc: Make atomic locks raw
apbuart: Fix build and missing driver unregister.
apbuart: Kill dependency on deprecated Sparc-only PROM interfaces.
apbuart: Fix build warning.
sparc: Support for GRLIB APBUART serial port
watchdog: Remove BKL from rio watchdog driver
sparc: Remove BKL from apc
sparc,leon: Sparc-Leon SMP support
Currently serial ports on SH CPUs get disabled too early, because the
sci_tx_empty() routine claims to not be able to detect whether the
transmission has been completed and just always returns TIOCSER_TEMT. This
results in corrupt output of last characters if the port is not open for
reading at the same time. It is however possible to detect whether
transmission has been completed. Use the TEND bit of the status register
for this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The function mcf_remove is used only wrapped by __devexit_p so define it
using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
There are a number of statements of the form A, B or A, B, C where
the numbers A,B,C are not consecutive. However, referencing [1] it
is the correct thing to replace these with A-B or A-C as apropriate.
[1] http://www.copyrightservice.co.uk/copyright/p03_copyright_notices
section 4iii 'Year of publication'
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Many boards have a bug-free ns16550 compatible serial port, which we should
register as PORT_16550A. This introduces a new value "ns16550a" for the
compatible property of of_serial to let a firmware choose that model instead
of using the crippled PORT_16550 mode.
Reported-by: Alon Ziv <alonz@nolaviz.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver missed a small API change while sitting in Ralf's tree, this
patch makes it compile again.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sunsu: Use sunserial_console_termios() in sunsu_console_setup().
sunsu: Pass true 'ignore_line' to console match when RSC or LOM console.
serial: suncore: Fix RSC/LOM handling in sunserial_console_termios().
serial: suncore: Add 'ignore_line' argument to sunserial_console_match().
sunsu: Fix detection of SU ports which are RSC console or control.
sunsab: Do not set sunsab_reg.cons right before registering minors.
sparc64: Fix definition of VMEMMAP_SIZE.
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:
(1) IRQInfo2 was unused in any case, so drop it.
(2) IRQInfo1 was used write-only, so drop it.
(3) Instance (private data to be passed to the IRQ handler):
Most PCMCIA drivers using pcmcia_request_irq() to actually
register an IRQ handler set the "dev_id" to the same pointer
as the "priv" pointer in struct pcmcia_device. Modify the two
exceptions (ipwireless, ibmtr_cs) to also work this waym and
set the IRQ handler's "dev_id" to p_dev->priv unconditionally.
(4) Handler is to be of type irq_handler_t.
(5) Handler != NULL already tells whether an IRQ handler is present.
Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
irq_req_t.Attributes.
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The sh-sci code conditionalized the clock framework support in order to
give the other platforms a chance to catch up. sh64 supported this some
time ago and the forthcoming ARM changes handle this as well, this leaves
h8300 as the odd one out. H8300 has had since 2.5 to merge it's sh-sci
support upstream, and has yet to do so. At this point I will no longer be
holding back the driver to support an unreponsive architecture, 7 years
is quite enough of a grace period. Support is easily implemented on the
architecture if and when it ever decides to merge its changes upstream.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The function sci_remove is defined without any section modifier, so
don't use __devexit_p to wrap it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Magnus Damm <damm@opensource.se>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Be like the other Sun serial drivers otherwise the special handling of
OpenFirmware options and hard-coded overrides for LOM/RSC consoles
will not be handled.
Signed-off-by: David S. Miller <davem@davemloft.net>
RSC and LOM devices have fixed speed settings.
We already had some code to match and handle "rsc" named devices on
E250 systems, but we also have to handle 'rsc-console', 'rsc-control',
and 'lom-console'.
Also, in order to get this right regardless of what 'output-device'
happens to be, explicitly pass the UART device node pointer to this
routine.
Signed-off-by: David S. Miller <davem@davemloft.net>
This tells the logic to ignore the line match when deciding whether the
device is the OpenFirmware specified console device or not.
This is going to be used in the SU driver for rsc-console detection.
There is probably a better way to handle this, but this is the least
intrusive solution for now which we can validate won't break any other
cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
These device nodes are named "rsc-console" and "rsc-control" rather
than 'serial', but the device_type property is 'serial' so we'll
tip off of that for detection.
Signed-off-by: David S. Miller <davem@davemloft.net>
Other Sun serial drivers do not do this, and if we keep it this way
it ends up registering all serial devices as consoles rather than
just the one which we explicitly register via sunserial_console_match()
which uses add_preferred_console().
Signed-off-by: David S. Miller <davem@davemloft.net>
This seems to be a different model (with a different PCI ID) than the
"Quatro" card that is also in the list.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct uart_port::iobase is unsigned long, so use %lx as printk format
specifier.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert PCMCIA drivers to use the dynamic debug infrastructure, instead of
requiring manual settings of PCMCIA_DEBUG.
Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.
CC: linux-serial@vger.kernel.org
CC: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
drivers/serial/apbuart.c: In function ‘apbuart_probe’:
drivers/serial/apbuart.c:574: warning: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘resource_size_t’
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the APBUART serial port from Aeroflex
Gaisler's IP library GRLIB. It is currently used in all LEON3 designs
(SPARC V8) but can be used on other platforms as well (which support OF).
Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs,serial_cs:
add cis of PreMax ethernet pcmcia card,
and some Sierra Wireless serial card(AC555, AC7xx, AC8xx).
use PROD_ID for AC7xx, because MANF_ID of AC7xx and AC8xx are the same.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/ppc64: Use preempt_schedule_irq instead of preempt_schedule
powerpc: Minor cleanup to lib/Kconfig.debug
powerpc: Minor cleanup to sound/ppc/Kconfig
powerpc: Minor cleanup to init/Kconfig
powerpc: Limit memory hotplug support to PPC64 Book-3S machines
powerpc: Limit hugetlbfs support to PPC64 Book-3S machines
powerpc: Fix compile errors found by new ppc64e_defconfig
powerpc: Add a Book-3E 64-bit defconfig
powerpc/booke: Fix xmon single step on PowerPC Book-E
powerpc: Align vDSO base address
powerpc: Fix segment mapping in vdso32
powerpc/iseries: Remove compiler version dependent hack
powerpc/perf_events: Fix priority of MSR HV vs PR bits
powerpc/5200: Update defconfigs
drivers/serial/mpc52xx_uart.c: Use UPIO_MEM rather than SERIAL_IO_MEM
powerpc/boot/dts: drop obsolete 'fsl5200-clocking'
of: Remove nested function
mpc5200: support for the MAN mpc5200 based board mucmc52
mpc5200: support for the MAN mpc5200 based board uc101
The IBM Saturn serial card has only one port. Without that fixup,
the kernel thinks it has two, which confuses userland setup and
admin tools as well.
[akpm@linux-foundation.org: fix pci-ids.h layout]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Michael Reed <mreed10@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
is_power_of_2() appears not to be constant enough for BUILD_BUG_ON()
after the latest rework, so replace it with an open-coded test.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the PCMCIA core already determines the multifunction count, the
ConfigBase address and the Present value, we can use them directly
instead of parsing the CIS again. By making use of pcmcia_loop_config(),
we can further remove the remaining call to pcmcia_get_first_tuple()
and friends.
CC: linux-serial@vger.kernel.org
CC: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As in the commit 9b4a161777, use UPIO_MEM
rather than SERIAL_IO_MEM. Both have the same value.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@has_sc@
@@
#include <linux/serial_core.h>
@depends on has_sc@
@@
- SERIAL_IO_MEM
+ UPIO_MEM
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 46d57a449a ("serial: use tty_port pointers in the core code")
contained two bugs that causes (rare) crashes:
- the rename typoed one site
- a NULL check was missed
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Greg KH <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
ethoc: limit the number of buffers to 128
ethoc: use system memory as buffer
ethoc: align received packet to make IP header at word boundary
ethoc: fix buffer address mapping
ethoc: fix typo to compute number of tx descriptors
au1000_eth: Duplicate test of RX_OVERLEN bit in update_rx_stats()
netxen: Fix Unlikely(x) > y
pasemi_mac: ethtool get settings fix
add maintainer for network drop monitor kernel service
tg3: Fix phylib locking strategy
rndis_host: support ETHTOOL_GPERMADDR
ipv4: arp_notify address list bug
gigaset: add kerneldoc comments
gigaset: correct debugging output selection
gigaset: improve error recovery
gigaset: fix device ERROR response handling
gigaset: announce if built with debugging
gigaset: handle isoc frame errors more gracefully
gigaset: linearize skb
gigaset: fix reject/hangup handling
...
pcnet_cs,serial_cs:
add cis of National Semicondoctor's lan&modem mulitifunction pcmcia card,
NE2K, tamarack ethernet card,
and some serial card(COMpad2, COMpad4).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow users to force skipping the TXEN test at init time. Applies
to all serial ports. Intended for debugging only.
There is a blacklist for devices where we need to skip the test but the
list is not complete. This lets users force skipping the test so we can
determine if they need to be added to the list.
Some HP machines with weird serial consoles have this problem and there
may be more.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
