this fixes a regression since the fbcon rework.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On nv50 it became impossible to attempt a PCI ROM shadow of the VBIOS,
which will break some setups.
This patch also removes the different ordering of shadow methods for
pre-nv50 chipsets. The reason for the different ordering was paranoia,
but it should hopefully be OK to try shadowing PRAMIN first.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a regression caused by b2ea4aa67b
due to the way shared ddc with multiple digital connectors was handled.
You generally have two cases where DDC lines are shared:
- HDMI + VGA
- HDMI + DVI-D
HDMI + VGA is easy to deal with because you can check the EDID for the
to see if the attached monitor is digital. A shared DDC line with two
digital connectors is more complex. You can't use the hdmi bits in the
EDID since they may not be there with DVI<->HDMI adapters. In this case
all we can do is check the HPD pins to see which is connected as we have
no way of knowing using the EDID.
Reported-by: trapdoor6@gmail.com
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
A lot of 945GMs have had stability issues for a long time, this manifested as X hangs, blitter engine hangs, and lots of crashes.
one such report is at:
https://bugs.freedesktop.org/show_bug.cgi?id=20560
along with numerous distro bugzillas.
This only took a week of digging and hair ripping to figure out.
Tracked down and tested on a 945GM Lenovo T60,
previously running
x11perf -copypixwin500
or
x11perf -copywinpix500
repeatedly would cause the GPU to wedge within 4 or 5 tries, with random busy bits set.
After this patch no hangs were observed.
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The i915 memory arbiter has a register full of configuration
bits which are currently not defined in the driver header file.
Signed-off-by: Keith Packard <keithp@keithp.com>
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
copy_to_user() returns the number of bytes remaining to be copied, but
we want to return a negative error code. This gets copied to user
space.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make inclusion of <asm/agp.h> conditional on TTM_HAS_AGP. The use
of the functions declared in it is already conditional.
Reported-by: Geert Stappers <stappers@stappers.nl>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Geert Stappers <stappers@stappers.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current shrinker implementation requires the registered callback
to have global state to work from. This makes it difficult to shrink
caches that are not global (e.g. per-filesystem caches). Pass the shrinker
structure to the callback so that users can embed the shrinker structure
in the context the shrinker needs to operate on and get back to it in the
callback via container_of().
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The hibernate issues that got fixed in commit 985b823b91 ("drm/i915:
fix hibernation since i915 self-reclaim fixes") turn out to have been
incomplete. Vefa Bicakci tested lots of hibernate cycles, and without
the __GFP_RECLAIMABLE flag the system eventually fails to resume.
With the flag added, Vefa can apparently hibernate forever (or until he
gets bored running his automated scripts, whichever comes first).
The reclaimable flag was there originally, and was one of the flags that
were dropped (unintentionally) by commit 4bdadb9785 ("drm/i915:
Selectively enable self-reclaim") that introduced all these problems,
but I didn't want to just blindly add back all the flags in commit
985b823b91, and it looked like __GFP_RECLAIM wasn't necessary. It
clearly was.
I still suspect that there is some subtle reason we're missing that
causes the problems, but __GFP_RECLAIMABLE is certainly not wrong to use
in this context, and is what the code historically used. And we have no
idea what the causes the corruption without it.
Reported-and-tested-by: M. Vefa Bicakci <bicave@superonline.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The asics in question have the following requirements with regard to
their gart setups:
1. The GART aperture size has to be in the form of 2^X bytes, where X is from 25 to 31
2. The GART aperture MC base has to be aligned to a boundary equal to the size of the
aperture.
3. The GART page table has to be aligned to the boundary equal to the size of the table.
4. The GART page table size is: table_entry_size * (aperture_size / page_size)
5. The GART page table has to be allocated in non-paged, non-cached, contiguous system
memory.
This patch takes care 2. The rest should already be handled properly.
This fixes a regression noticed by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Unify debug printing so it easier to track what's happening
while debugging.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check ulBootUpMemoryClock on AMD IGPs.
Fix regression noticed by Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Original behaviour will be preserved for drivers that don't implement
disable() hooks for an encoder.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that highlevel DRM no longer requires PCI, we can move the requirement
into the lowlevel drivers.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
More explicit than dpms. Same as the encoder disable function.
Need this to explicity disconnect plls from crtcs for reuse when you
plls:crtcs ratio isn't 1:1.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-intel-lru:
drm: implement helper functions for scanning lru list
drm_mm: extract check_free_mm_node
drm: sane naming for drm_mm.c
drm: kill dead code in drm_mm.c
drm: kill drm_mm_node->private
drm: use list_for_each_entry in drm_mm.c
* drm-platform:
drm: Make sure the DRM offset matches the CPU
drm: Add __arm defines to DRM
drm: Add support for platform devices to register as DRM devices
drm: Remove drm_resource wrappers
We don't currently update the DPMS status of the connector (both in the
connector itself and the connector's DPMS property) in the fb helper
code. This means that if the kernel FB core has blanked the screen,
sysfs will still show a DPMS status of "on". It also means that when X
starts, it will try to light up the connectors, but the drm_crtc_helper
code will ignore the DPMS change since according to the connector, the
DPMS status is already on.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=28436 (the annoying
"my screen was blanked when I started X and now it won't light up" bug).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Connectors with a shared ddc line can be connected to different
encoders.
Reported by Pasi Kärkkäinen <pasik@iki.fi> on dri-devel
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
These helper functions can be used to efficiently scan lru list
for eviction. Eviction becomes a three stage process:
1. Scanning through the lru list until a suitable hole has been found.
2. Scan backwards to restore drm_mm consistency and find out which
objects fall into the hole.
3. Evict the objects that fall into the hole.
These helper functions don't allocate any memory (at the price of
not allowing any other concurrent operations). Hence this can also be
used for ttm (which does lru scanning under a spinlock).
Evicting objects in this fashion should be more fair than the current
approach by i915 (scan the lru for a object large enough to contain
the new object). It's also more efficient than the current approach used
by ttm (uncoditionally evict objects from the lru until there's enough
free space).
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Thomas Hellstrom <thellstrom@vmwgfx.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are already two copies of this logic. And the new scanning
stuff will add some more. So extract it into a small helper
function.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Thomas Hellstrom <thellstrom@vmwgfx.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Yeah, I've kinda noticed that fl_entry is the free stack. Still
give it (and the memory node list ml_entry) decent names.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Thomas Hellstrom <thellstrom@vmwgfx.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Thomas Hellstrom <thellstrom@vmwgfx.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only ever assigned, never used.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[glisse: I will re-add if needed for range-restricted allocations]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Thomas Hellstrom <thellstrom@vmwgfx.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Repeated ttm_page_alloc_init/fini fails noisily because the pool
manager kobj isn't zeroed out between uses (we could do just that but
statically allocated kobjects are generally considered a bad thing).
Move it to kzalloc'ed memory.
Note that this patch drops the refcounting behavior of the pool
allocator init/fini functions: it would have led to a race condition
in its current form, and anyway it was never exploited.
This fixes a regression with reloading kms modules at runtime, since
page allocator was introduced.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Allows us to track each process that requests and completes events.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Emit a trace point for vblank events. This can be helpful for mapping
drawing activity against the vblank frequency and period.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix page flip finish vs. prepare on plane B
drm/i915: change default panel fitting mode to preserve aspect ratio
drm/i915: fix uninitialized variable warning in i915_setup_compression()
drm/i915: take struct_mutex in i915_dma_cleanup()
drm/i915: Fix CRT hotplug regression in 2.6.35-rc1
i915: fix ironlake edp panel setup (v4)
drm/i915: don't access FW_BLC_SELF on 965G
drm/i915: Account for space on the ring buffer consumed whilst wrapping.
drm/i915: gen3 page flipping fixes
drm/i915: don't queue flips during a flip pending event
drm/i915: Fix incorrect intel_ring_begin size in BSD ringbuffer.
drm/i915: Turn on 945 self-refresh only if single CRTC is active
drm/i915/gen4: Fix interrupt setup ordering
drm/i915: Use RSEN instead of HTPLG for tfp410 monitor detection.
drm/i915: Move non-phys cursors into the GTT
Revert "drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on)."
(Included the "fix page flip finish vs. prepare on plane B" patch from
Jesse on top of the pull request from Eric. -- Linus)
Since commit 4bdadb9785 ("drm/i915:
Selectively enable self-reclaim"), we've been passing GFP_MOVABLE to the
i915 page allocator where we weren't before due to some over-eager
removal of the page mapping gfp_flags games the code used to play.
This caused hibernate on Intel hardware to result in a lot of memory
corruptions on resume. See for example
http://bugzilla.kernel.org/show_bug.cgi?id=13811
Reported-by: Evengi Golov (in bugzilla)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tested-by: M. Vefa Bicakci <bicave@superonline.com>
Cc: stable@kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We did this a long time ago in the DDX driver, but now this fix belongs
in the kernel.
Preserving the aspect ratio is a nicer default.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=18033.
Tested-by: Josh Triplett <josh@freedesktop.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes:
drivers/gpu/drm/i915/i915_dma.c: In function ‘i915_setup_compression’:
drivers/gpu/drm/i915/i915_dma.c:1311: error: ‘compressed_llb’ may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
intel_cleanup_ring_buffer() calls drm_gem_object_unreference() (as
opposed to drm_gem_object_unreference_unlocked()) so it needs to be
called with "struct_mutex" held. If we don't hold the lock, it triggers
a BUG_ON(!mutex_is_locked(&dev->struct_mutex));
I also audited the other places that call intel_cleanup_ring_buffer()
and they all hold the lock so they're OK.
This was introduced in: 8187a2b70e "drm/i915: introduce
intel_ring_buffer structure (V2)" and it's a regression from v2.6.34.
Addresses: https://bugzilla.kernel.org/show_bug.cgi?id=16247
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reported-by: Benny Halevy <bhalevy@panasas.com>
Tested-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 7a772c492f has two bugs which
made the hotplug problems on my laptop worse instead of better.
First, it did not, in fact, disable the CRT plug interrupt -- it
disabled all the other hotplug interrupts. It seems rather doubtful
that that bit of the patch fixed anything, so let's just remove it.
(If you want to add it back, you probably meant ~CRT_HOTPLUG_INT_EN.)
Second, on at least my GM45, setting CRT_HOTPLUG_ACTIVATION_PERIOD_64
and CRT_HOTPLUG_VOLTAGE_COMPARE_50 (when they were previously unset)
causes a hotplug interrupt about three seconds later. The old code
never restored PORT_HOTPLUG_EN so this could only happen once, but
they new code restores those registers. So just set those bits when
we set up the interrupt in the first place.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Eric Anholt <eric@anholt.net>
The eDP spec claims a 20% overhead for the 8:10 encoding scheme used
on the wire. Take this into account when picking the lane/clock speed
for the panel.
v3: some panels are out of spec, try our best to deal with them, don't
refuse modes on eDP panels, and try the largest allowed settings if
all else fails on eDP.
v4: fix stupid typo, forgot to git add before amending.
Fixes several reports in bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=28070
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The register offset for FW_BLC_SELF is a totally different set of bits
on Broadwater (it's actually MI_RDRET_STATE), so don't treat it like
FW_BLC_SELF on 965G chips.
Fixes bug https://bugs.freedesktop.org/show_bug.cgi?id=26874.
Cc: stable@kernel.org
Tested-by: Norman Yarvin <yarvin@yarchive.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
If we fill the tail of the physical ring buffer with NOOP when wrapping,
we need to account for the reduction in available space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some RV100 cards with 2 VGA ports show up with DVI+VGA, however
some boards with DVI+VGA have the same subsystem ids. Better
to have a VGA port show up as DVI than having a non-useable
DVI port.
reported by DHR in irc.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is a regression from 2.6.34 related to the recent radeon power
management changes, caused by attempting to cancel a delayed work
item that's never been scheduled. However, the code as is has some
other issues potentially leading to visible problems.
First, the mutex around cancel_delayed_work() in radeon_pm_suspend()
doesn't really serve any purpose, because cancel_delayed_work() only
tries to delete the work's timer. Moreover, it doesn't prevent the
work handler from running, so the handler can do some wrong things if
it wins the race and in that case it will rearm itself to do some
more wrong things going forward. So, I think it's better to wait for
the handler to return in case it's already been queued up for
execution. Also, it should be prevented from rearming itself in that
case.
Second, in radeon_set_pm_method() the cancel_delayed_work() is not
sufficient to prevent the work handler from running and queing up
itself for the next run (the failure scenario is that
cancel_delayed_work() returns 0, so the handler is run, it waits on
the mutex and then rearms itself after the mutex has been released),
so again the work handler should be prevented from rearming itself in
that case..
Finally, there's a potential deadlock in radeon_pm_fini(), because
cancel_delayed_work_sync() is called under rdev->pm.mutex, but the
work handler tries to acquire the same mutex (if it wins the race).
Fix the issues described above.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some IGP systems specify the system memory clock in the Firmware
table rather than the IGP info table. Check both and make sure
we have a value system memory clock value.
v2: make sure rs690_pm_info is called on rs780/rs880 as well.
fixes a regression since 07d4190327b02ab3aaad25a2d168f79d92e8f8c2.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For some reason on resume, executing the BIOS scripts locks up the whole chipset, by avoiding the dynclk table the machine resumes properly and seems to function okay.
Signed-off-by: Dave Airlie <airlied@redhat.com>
They don't have an atombios so don't attempt to use it for
eng/mem clocks.
Reported by spoonb on #radeon
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28671
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
HDP non surface should cover the whole VRAM but we were misscomputing
the size and we endup in some case not covering the VRAM at all (if
VRAM size were > 1G). Covering more than the VRAM size shouldn't be
an issue.
Fix : https://bugs.freedesktop.org/show_bug.cgi?id=28016
[airlied: add evergreen fix]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since the VGA switcheroo, we'd attempt to read the BIOS from VRAM on startup
but on some unposted cards this can cause hangs/crashes.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=28592
(further problem pointed out by agd5f on IGP systems)
Reported-by: Reilithion on #radeon
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were returning 0 in both the success and failure paths. Noticed while
investigating FDO bug 26403.
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Non pooled page allocation should have GFP_USER set so allocation
can wait and reclaim page from other process (ie non atomic).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This needs similar handling to other compressed textures.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=26428
Signed-off-by: sroland@vmware.com
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Code did not handle projected 2d and depth coordinates, meaning potentially
set 3d or cube special handling might stick.
(Not sure what depth coord actually does, but I guess handling it
like a normal coordinate is the right thing to do.)
Might be related to https://bugs.freedesktop.org/show_bug.cgi?id=26428
Signed-off-by: sroland@vmware.com
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28459
agd5f: apply to r1xx/r2xx as well.
Signed-off-by: Roland Scheidegger <sroland@vmware.com>
Cc: stable@kernel.org
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This works well enough on a js21, but it would be nice if IBM could supply
more tables for the later Power6/7 machines.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reduced blanking is valid only when doing CVT modes. Also, generate GTF
modes unless CVT was requested; CVT devices are required to support GTF,
but the reverse is not true.
[airlied: fix typo]
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The transmitter needs to be enabled before the link is trained.
Reported-By: Lars Doelle <lars.doelle@on-line.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When suspending, we turn the display hw off, at resume the screen will stay black.
This patch turn it on. Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16180
Signed-off-by: Cedric Godin <cedric.godin@skynet.be>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Gen3 chips have slightly different flip commands, and also contain a bit
that indicates whether a "flip pending" interrupt means the flip has
been queued or has been completed.
So implement support for the gen3 flip command, and make sure we use the
flip pending interrupt correctly depending on the value of ECOSKPD bit
0.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Hardware will set the flip pending ISR bit as soon as it receives the
flip instruction, and (supposedly) clear it once the flip completes
(e.g. at the next vblank). If we try to send down a flip instruction
while the ISR bit is set, the hardware can become very confused, and we
may never receive the corresponding flip pending interrupt, effectively
hanging the chip.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The ring_begin API was taking a number of bytes, while all of our
other begin/end macros take number of dwords. Change the API over to
dwords to prevent future bugs.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Enable self-refresh on 945 when just one CRTC is activated.
Otherwise user would get display flicker with dual display.
This fixes https://bugs.freedesktop.org/show_bug.cgi?id=27667
Signed-off-by: Li Peng <peng.li@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Installing 2.6.34 on a Power5/rn50 combo machine, X showed buggy sw rendering,
enabling tiling in the DDX fixed it. Investigation showed that a further /16
was needed in the untiled case on this chipset. Need further investigations
on what other chips this could affect, possibly rv100->rv280.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Plugged in FireMV with the rv250 on it, and the second crtc/dac didn't work,
we were reading/writing different registers than we were modifying in the code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit cfecde435d, since it
seems to cause some systems to not come up with any video output at all
(or video that only comes on when X starts up).
Fixes bugzilla:
http://bugzilla.kernel.org/show_bug.cgi?id=16163
Reported-and-tested-by: David John <davidjon@xenontk.org>
Tested-by: Nick Bowler <nbowler@elliptictech.com>
Acked-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
So when we added output polling, we'd suddenly use this code more often, and the fact that it always takes over crtc2 and messes with it during probing isn't what we really want to be happening. A more complete fix would to change it to use whatever crtc was free at the time, but for now lets stay simple and just don't poll if crtc2 is already in use.
Although a more correct fix was found I suspect we should do this as well, until we get a chance to readdres the tv out polling issues.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We really don't want to be polling tv-out but since we weren't forcing the
i2c lines to invalid (tv-out has no DDC), we were adding tv connectors to the
polling setup and this was causing blinking on secondary displays.
This fixes the regression Torsten reported.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
dcb->i2c[] has DCB_MAX_NUM_I2C_ENTRIES entries.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If "gpio->line" is 32 then "nv50_gpio_reg[gpio->line >> 3]" reads past the
end of the array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On cards where there's a specific BAR for PRAMIN, we used to try and fall
back to the "legacy" aperture within the mmio BAR.
This is doomed to cause problems, so lets just fail completely as there's
obviously something else very wrong anyway.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It appears version 0x21 'U' and 'd' tables require us to take the SOR link
into account when selecting the appropriate table for a particular output.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes FDO bug #28375, it's kind of regression, so quite important to have
it for .35.
V2: Fix on RV770+ as well. All other chipsets have only one clock mode per
state.
V3: I'm out of luck today. Grepped for voltage in r*.c and missed evergreen.
agd5f: rebased
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
track the current voltage level and avoid setting it
if the requested voltage is already set.
v2: check voltage type before checking current voltage
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vddc value in the power tables is not an actual voltage
like on discrete r6xx/r7xx/evergreen systems, but instead has
a symbolic meaning (e.g., NONE, LOW, HIGH, etc.). See atombios.h
Most RS780/RS880 vbioses don't have a SetVoltage table anyway,
so it shouldn't be doing anything to the hardware at the moment.
I need to figure out how voltage is supposed to work on the newer
IGPs; until then, disable it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds an additional profile, mid, to the pm profile
code which takes the place of the old low profile. The default
behavior remains the same, e.g., auto profile now selects between
mid and high profiles based on power source, however, you can now
manually force the low profile which was previously only available
as a dpms off state. Enabling the low profile when the displays
are on has been known to cause display corruption in some cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- don't rest the power state in pm_init()
We already boot up to the default power state. Note this
patch relies on:
drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
To make sure the default power state matches the boot up state.
- In the pm resume path asic init will have set the power state
back to the default so reset the tracking state values.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed to enable accel in the ddx. However,
due to a bug in older versions of the ddx, it relies
on accel being disabled in order to load properly on
evergreen chips. To maintain compatility, we add a new
get accel param and call that from the ddx. The old one
always returns false for evergreen cards.
[this fixes a regression with older userspaces on newer kernels].
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
copy_to/from_user() returns the number of bytes remaining to be copied
but we want to return a negative error code here. This gets returned to
userspace.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
copy_from_user() returns the number of bytes left to be copied but we
want to return a negative error code here. This is in the ioctl handler
so the error code get returned to userspace.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
using DRM_ERROR, results in people blaming the drm code for the oops, and
not looking at the oops.
(sadly yes I've gotten reports).
Signed-off-by: Dave Airlie <airlied@redhat.com>
PM attemps to unmap objects that aren't actually mapped into userspace ever,
so just don't bother unmapping them at this point, since all you are doing
is nothing. We should be making sure all access to these objects are locked in
kernel space instead. In theory the VRAM gart table is already done, and both
the shaders and stolen vga memory blocks are never accessed at runtime.
fixes: https://bugzilla.kernel.org/show_bug.cgi?id=16127
Reported-by: Jure Repnic <jlp.bugs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The previous commit fixes the problem, these commits make sure we actually
fail properly if it happens again.
I've squashed the commits from Chris since they are all fixing one issue.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(regression fix since fbdev/kms rework).
My fb rework didn't remember about the 84/65s.
Reported-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cursors need to be in the GTT domain when being accessed by the GPU.
Previously this was a fortuitous byproduct of userspace using pwrite()
to upload the image data into the cursor. The redundant clflush was
removed in commit 9b8c4a and so the image was no longer being flushed
out of the caches into main memory. One could also devise a scenario
where the cursor was rendered by the GPU, prior to being attached as the
cursor, resulting in similar corruption due to the missing MI_FLUSH.
Fixes:
Bug 28335 - Cursor corruption caused by commit 9b8c4a0b21https://bugs.freedesktop.org/show_bug.cgi?id=28335
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unmask, then enable interrupts, then enable interrupt sources; matches
PCH ordering. The old way (sources, enable, unmask) gives a window
during which interrupt conditions would appear in ISR but would never
reach IIR and thus never raise an IRQ. Since interrupts only trigger
on rising edges in ISR, this would lead to conditions where (for
example) output hotplugging would never fire an interrupt because it
was already stuck on in ISR.
Also, since we know IIR and PIPExSTAT have been cleared during
irq_preinstall, don't clear them again during irq_postinstall, nothing
good can come of that.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (41 commits)
drm/radeon/kms: make sure display hw is disabled when suspending
drm/vmwgfx: Allow userspace to change default layout. Bump minor.
drm/vmwgfx: Fix framebuffer modesetting
drm/vmwgfx: Fix vga save / restore with display topology.
vgaarb: use MIT license
vgaarb: convert pr_devel() to pr_debug()
drm: fix typos in Linux DRM Developer's Guide
drm/radeon/kms/pm: voltage fixes
drm/radeon/kms/pm: radeon_set_power_state fixes
drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
drm/radeon/kms/pm: enable SetVoltage on r7xx/evergreen
drm/radeon/kms/pm: add support for SetVoltage cmd table (V2)
drm/radeon/kms/evergreen: add initial CS parser
drm/kms: disable/enable poll around switcheroo on/off
drm/nouveau: fixup confusion over which handle the DSM is hanging off.
drm/nouveau: attempt to get bios from ACPI v3
drm/nv50: cast IGP memory location to u64 before shifting
drm/ttm: Fix ttm_page_alloc.c
drm/ttm: Fix cached TTM page allocation.
drm/vmwgfx: Remove some leftover debug messages.
...
Disable the display hw when suspending.
Should fix bug:
https://bugzilla.redhat.com/show_bug.cgi?id=522393
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The host may change the layout and, since the change is
communicated to the master, the master needs a way to
communicate the change to the kernel driver.
The minor version number is bumped to advertize the
availability of this feature.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
