Some pins are expected to keep their last level during suspend, and
introduce MFP_LPM_KEEP_OUTPUT for this.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
'mach-pxa' platforms currently rely on a bootloader to setup GPIO pins
and clear RDH (to enable inputs).
A kernel loaded by a 'minimal' bootloader, that doesn't touch any pins,
will not function correctly; inputs will remain disabled, even after the
pins are configured. The following change fixes the issue and has been
verified on Gumstix Verdex XL6P and a custom PXA270 platform.
Signed-off-by: Timothy Clacy <tcl@phaseone.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Let's handle GPIOs by banks, each bank covers up to 32 GPIOs with one set
of registers, and each set of registers start from different offsets.
GPLR GPDR GPSR GPCR GRER GFER GEDR
BANK 0 - 0x0000 0x000C 0x0018 0x0024 0x0030 0x003C 0x0048
BANK 1 - 0x0004 0x0010 0x001C 0x0028 0x0034 0x0040 0x004C
BANK 2 - 0x0008 0x0014 0x0020 0x002C 0x0038 0x0044 0x0050
BANK 3 - 0x0100 0x010C 0x0118 0x0124 0x0130 0x013C 0x0148
BANK 4 - 0x0104 0x0110 0x011C 0x0128 0x0134 0x0140 0x014C
BANK 5 - 0x0108 0x0114 0x0120 0x012C 0x0138 0x0144 0x0150
NOTE:
BANK 3 is only available on PXA27x and later processors.
BANK 4 and 5 are only available on PXA935
1. introduce GPIO_BANK(n) for the offset base of each bank
2. 'struct pxa_gpio_chip' is expanded to include IRQ edge and mask
setings, and saved register values as well, and is dynamically
allocated due to possible bank number ranging from 3 to 6
3. all accesses to GPIO registers are made through 'regbase' within
'pxa_gpio_chip', and register offset
4. introduce several inline functions to simplify the code a bit
5. change IRQ demux handler to base on gpio chips
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This makes gpio.c fully independent of pxa-regs.h (except for the
virtual address of the registers).
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Original patch from Marek Vasut, the problems with PXA26x are:
1. there are additional 4 GPIOs 86,87,88,89 have their direction bits
inverted in GPDR2, as well as their alternate function bits being
'1' for their GPIO functionality in GAFRx
2. there is no easy way to decide if the processor is a pxa26x or a
pxa250/pxa255 at run-time, so the assumption here is the pxa26x
will be treated as one of the pxa25x variants, and board code
should have a better knowledge of the processor it is featured
Introduce pxa26x_init_irq() for the second purpose, and treat the
additional GPIOs > 85 on PXA25x specially.
Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code
a bit when PXA26x support isn't needed. Board config options have
to select this to enable the support for PXA26x.
__gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x
isn't selected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we
already have that variable, remove the unnecessary 'gpio_nr' now.
Also, fix the incorrect GPIO number passed in pxa27x_init_irq().
Note: pxa_last_gpio should be initialized earlier, and this is true
since it's been assigned in machine_desc->init_irq().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PXA SoC have several GPIOs muxed on only one wakeup source.
Add support for these wakeup sources which were missing
in mfp core support.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The initialization of mfp sysdev in pxa2xx_mfp_init() shall really be
avoided when !cpu_is_pxa2xx().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When configured as a specific low power state: MFP_LPM_DRIVE_LOW,
MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during
low power mode shall be re-configured as output (if they are not
configured so), thus the PGSRx bits can output.
Create an additional low power values GPDR registers, and properly
save/restore the GAFR + GPDR registers when doing suspend/resume.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some boards want to change low power state of pins on-the-fly, this
function helps to facilitate that operation instead of switching
back-n-forth between two configurations with pxa2xx_mfp_config().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The power manager and core clock registers aren't present in PXA3
CPUs. Move them out of pxa-regs.h into pxa2xx-regs.h, and include
pxa2xx-regs.h where necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Changes include:
1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate
the board capability of this pin to wakeup the system
2. add gpio_set_wake() and keypad_set_wake() to allow dynamically
enable/disable wakeup from GPIOs and keypad GPIO
* these functions are currently kept in mfp-pxa2xx.c due to their
dependency to the MFP configuration
3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP
is set on incorrect pins
So that the GPIO's wakeup capability is now decided by the following:
a) processor's capability: (only those GPIOs which have dedicated
bits within PWER/PRER/PFER can wakeup the system), this is
initialized by pxa{25x,27x}_init_mfp()
b) board design decides:
- whether the pin is designed to wakeup the system (some of
the GPIOs are configured as other functions, which is not
intended to be a wakeup source), by OR'ing the pin config
with MFP_LPM_CAN_WAKEUP
- which edge the pin is designed to wakeup the system, this
may depends on external peripherals/connections, which is
totally board specific; this is indicated by MFP_LPM_EDGE_*
c) the corresponding device's (most likely the gpio_keys.c) wakeup
attribute:
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
- MFP_PIN(x)
- MFP_AFx
- MFP_LPM_DRIVE_{LOW, HIGH}
- MFP_LPM_EDGE_*
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
- WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
- WAKEUP_ON_LEVEL_HIGH
The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.
These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.
The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
